Investigations of the Sulfonated Poly(ether ether ketone) Membranes with Various Degrees of Sulfonation by Considering Durability for the Proton Exchange Membrane Fuel Cell (PEMFC) Applications
Open accessThe DOI matches its Crossref record; 60 of the 60 references it cites were found in a registry or an index; none of the 24 sources its claims cite is checked for support yet.
Abstract
The optimum degree of sulfonation for SPEEK membranes is determined by combining proton conductivity, swelling, water uptake, chemical stability, thermal stability, mechanical tests, and PEMFC performance.
Overview
CoChat Summary
## TL;DR
This paper studies SPEEK membranes with different degrees of sulfonation (DS) for PEMFCs and shows a tradeoff: higher DS improves proton conductivity, but lowers mechanical, thermal, and chemical durability. Considering both performance and durability, the authors argue that SPEEK membranes with DS around 51–62% are more suitable than the previously favored higher-DS membranes.
## Key findings
- Water uptake increased from 7.3% to 43.3% and swelling ratio from 4.2% to 15.4% as sulfonation duration increased from 1.5 to 4 h at 55 °C.
- The paper states that proton conductivity increased with DS, but mechanical, thermal, and chemical stability decreased as DS increased.
- In the Fenton durability test, SPEEK-51 showed the best chemical stability among the membranes discussed; its complete degradation time was about twice that of SPEEK-62, and at crack formation its WU was below 35% versus 107% for SPEEK-62.
- In PEMFC single-cell testing at 80 °C and 100% RH, the SPEEK-62 membrane reached a peak power density of 482.08 mW/cm², exceeding Nafion-212 at 365.16 mW/cm²; SPEEK-51 reached 236.93 mW/cm² under the same condition.
- Under 70 °C and 100% RH OCV durability testing, OCV decays were 0.08 V for SPEEK-51, 0.242 V for SPEEK-62, and 0.141 V for Nafion-212, corresponding to decay rates of 1.33, 4.03, and 2.35 mV h−1, respectively.
## Methods
- SPEEK membranes were prepared from PEEK by sulfonation in concentrated sulfuric acid at 55 °C for 1.5–4 h, yielding membranes labeled SPEEK-34, 43, 51, 62, 72 based on DS.
- The paper characterized membranes using FTIR, SEM, tensile testing, swelling ratio and water uptake, TGA, acid–base titration for IEC/DS, proton conductivity by impedance spectroscopy, Fenton oxidative stability tests, and PEMFC single-cell tests/OCV durability tests.
- Single-cell MEAs were fabricated by hot pressing SPEEK membranes with productized GDEs, then tested at 70, 75, and 80 °C under 100% RH, and OCV durability was tested at 70 °C and 50% RH.
## Limitations
- The paper explicitly notes that SPEEK-34 was not further discussed because its proton conductivity was below 60 mS/cm, and its poor solubility in DMF made membrane preparation difficult.
- The text indicates that the results are based on a small set of membrane DS values; this is evident from the study design, but the paper does not present broader sampling or replication details here.
- The text makes evident that some performance conclusions depend on specific testing conditions (for example, 100% RH, 50% RH, and selected temperatures), so generalization beyond those conditions is not directly established in the provided text.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures









Verification
Claims the paper makes
0 Valid · 0 Not valid · 10 Not checked · 40 Own results and interpretations
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“SPEEK membranes with a lower DS exhibit higher stability compared to the higher ones.”
§ Investigations of the Sulfonated Poly(ether ether ketone) Membranes with Various Degrees of Sulfonation by Considering Durability for the Proton Exchange Membrane Fuel Cell (PEMFC) Applications > 3. Results and Discussion > 3.7. Oxidative Stability
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Due to its extremely low proton conductivity (<60 mS/cm)”
§ Investigations of the Sulfonated Poly(ether ether ketone) Membranes with Various Degrees of Sulfonation by Considering Durability for the Proton Exchange Membrane Fuel Cell (PEMFC) Applications > 3. Results and Discussion > 3.6. Proton Conductivity
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“As the sulfonation reaction time lasts, more -SO3H groups are incorporated into the backbone of the PEM structure.”
§ Investigations of the Sulfonated Poly(ether ether ketone) Membranes with Various Degrees of Sulfonation by Considering Durability for the Proton Exchange Membrane Fuel Cell (PEMFC) Applications > 3. Results and Discussion > 3.5. IEC
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“the proton conductivity data obtained across the entire tested temperature range is far below the SPEEK membrane with higher DS values.”
§ Investigations of the Sulfonated Poly(ether ether ketone) Membranes with Various Degrees of Sulfonation by Considering Durability for the Proton Exchange Membrane Fuel Cell (PEMFC) Applications > 3. Results and Discussion > 3.6. Proton Conductivity
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The outcomes demonstrate dense and homogeneous morphology in terms of all the SPEEK membranes.”
§ Investigations of the Sulfonated Poly(ether ether ketone) Membranes with Various Degrees of Sulfonation by Considering Durability for the Proton Exchange Membrane Fuel Cell (PEMFC) Applications > 3. Results and Discussion > 3.2. SEM
boosted- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
24 more claims
Create a free account to see all 50 claims and to verify the 1 reference still open.
- It may state two separate claims as one. 16
- Probably not a substantial claim. 5
Citations
Cites
Review of the proton exchange membranes for fuel cell applications
Peighambardoust, S. J., Rowshanzamir, S., & Amjadi, M. (2010) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2010.05.017 · Cited by 2,186 · cited 1×
“…membrane fuel cells (PEMFCs) are the most prospective electro-chemical energy generation devices at present for transport and stationary applications as a result of their transient response time, industrial adaptability, extraordinary energy density, and environmental friendliness [1–3].”
Park, C. H., Lee, C. H., Guiver, M. D., & Lee, Y. M. (2011) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2011.06.001 · Cited by 682
Degradation of polymer electrolyte membranes
COLLIER, A., WANG, H., ZIYUAN, X., ZHANG, J., & WILKINSON, D. (2006) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2006.05.006 · Cited by 538
Influence of geometric parameters of the flow fields on the performance of a PEM fuel cell. A review
Manso, A. P., Marzo, F. F., Barranco, J., Garikano, X., & Garmendia Mujika, M. (2012) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2012.07.076 · Cited by 487
Developments of electric cars and fuel cell hydrogen electric cars
Wilberforce, T., El-Hassan, Z., Khatib, F. N., Al Makky, A., Baroutaji, A., Carton, J. G., & Olabi, A. G. (2017) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2017.07.054 · Cited by 478
Developments in fuel cell technologies in the transport sector
Alaswad, A., Baroutaji, A., Achour, H., Carton, J., Al Makky, A., & Olabi, A. G. (2016) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2016.03.164 · Cited by 378
Mechanical endurance of polymer electrolyte membrane and PEM fuel cell durability
Huang, X., Solasi, R., Zou, Y., Feshler, M., Reifsnider, K., Condit, D., Burlatsky, S., & Madden, T. (2006) · Journal of Polymer Science Part B: Polymer Physics · doi:10.1002/polb.20863 · Cited by 369
A review of polymer electrolyte membrane fuel cell durability test protocols
Yuan, X.-Z., Li, H., Zhang, S., Martin, J., & Wang, H. (2011) · Journal of Power Sources · doi:10.1016/j.jpowsour.2011.07.082 · Cited by 354
Review on water management methods for proton exchange membrane fuel cells
Wang, X. R., Ma, Y., Gao, J., Li, T., Jiang, G. Z., & Sun, Z. Y. (2021) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2020.06.211 · Cited by 318
Sun, C., Negro, E., Vezzù, K., Pagot, G., Cavinato, G., Nale, A., Herve Bang, Y., & Di Noto, V. (2019) · Electrochimica Acta · doi:10.1016/j.electacta.2019.03.056 · Cited by 261
Self-citationWater droplet accumulation and motion in PEM (Proton Exchange Membrane) fuel cell mini-channels
Carton, J. G., Lawlor, V., Olabi, A. G., Hochenauer, C., & Zauner, G. (2012) · Energy · doi:10.1016/j.energy.2011.10.023 · Cited by 255
Sulfonated PEEK-based polymers in PEMFC and DMFC applications: A review
Iulianelli, A., & Basile, A. (2012) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2012.07.063 · Cited by 255
PEM fuel cell relative humidity (RH) and its effect on performance at high temperatures
Zhang, J., Tang, Y., Song, C., Xia, Z., Li, H., Wang, H., & Zhang, J. (2008) · Electrochimica Acta · doi:10.1016/j.electacta.2008.02.074 · Cited by 231
Janssen, G. J. M., & Overvelde, M. L. J. (2001) · Journal of Power Sources · doi:10.1016/s0378-7753(01)00708-x · Cited by 230
Zhang, H., Li, X., Zhao, C., Fu, T., Shi, Y., & Na, H. (2008) · Journal of Membrane Science · doi:10.1016/j.memsci.2007.09.045 · Cited by 195 · cited 1×
“As reported in the literature, SPEEK membranes with a DS that is too high exhibit excessive swelling behavior and even dissolve in aqueous solutions at high temperatures; so it is difficult to find commercial SPEEK membranes in the market [39–41].”
Parnian, M. J., Rowshanzamir, S., & Gashoul, F. (2017) · Energy · doi:10.1016/j.energy.2017.02.143 · Cited by 186 · cited 2×
“Moreover, the DS of SPEEK was determined by Equation (4) based on the IEC values [30].”
Gas diffusion layers for PEM fuel cells: Materials, properties and manufacturing – A review
Athanasaki, G., Jayakumar, A., & Kannan, A. M. (2023) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2022.10.058 · Cited by 180
Yang, L., Nik-Ghazali, N.-N., Ali, M. A. H., Chong, W. T., Yang, Z., & Liu, H. (2023) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2023.113737 · Cited by 168
Jiang, R., Kunz, H. R., & Fenton, J. M. (2005) · Journal of Power Sources · doi:10.1016/j.jpowsour.2005.03.180 · Cited by 164
Recent developments of proton exchange membranes for PEMFC: A review
Parekh, A. (2022) · Frontiers in Energy Research · doi:10.3389/fenrg.2022.956132 · Cited by 149
Contaminant absorption and conductivity in polymer electrolyte membranes
Kelly, M. J., Fafilek, G., Besenhard, J. O., Kronberger, H., & Nauer, G. E. (2005) · Journal of Power Sources · doi:10.1016/j.jpowsour.2005.01.064 · Cited by 147 · cited 1×
“In the Fenton test, certain metallic species, including Fe 2+ , were employed for the decomposition of H 2 O 2 to create free radicals, as presented in Equations (7) and (8), and the generated free radicals may attack the PEM and degrade the backbone of SPEEK membranes [52–54].”
Carbone, A., Pedicini, R., Portale, G., Longo, A., D’Ilario, L., & Passalacqua, E. (2006) · Journal of Power Sources · doi:10.1016/j.jpowsour.2005.12.066 · Cited by 143 · cited 1×
“The chemical stability and proton conductivity of SPEEK membranes are highly correlated with the DS, and it is possible to adjust the DS value through altering the reaction conditions and processing factors, including reaction time and sulfonation temperature [42–44].”
Zhang, L., & Mukerjee, S. (2006) · Journal of The Electrochemical Society · doi:10.1149/1.2180715 · Cited by 137 · cited 1×
“In the Fenton test, certain metallic species, including Fe 2+ , were employed for the decomposition of H 2 O 2 to create free radicals, as presented in Equations (7) and (8), and the generated free radicals may attack the PEM and degrade the backbone of SPEEK membranes [52–54].”
Kim, A. R., Poudel, M. B., Chu, J. Y., Vinothkannan, M., Santhosh Kumar, R., Logeshwaran, N., Park, B.-H., Han, M.-K., & Yoo, D. J. (2023) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2023.110558 · Cited by 136
Li, X., Ye, T., Meng, X., He, D., Li, L., Song, K., Jiang, J., & Sun, C. (2024) · Polymers · doi:10.3390/polym16192840 · Cited by 135
Self-citationFuel cell life prediction considering the recovery phenomenon of reversible voltage loss
Meng, X., Sun, C., Mei, J., Tang, X., Hasanien, H. M., Jiang, J., Fan, F., & Song, K. (2024) · Journal of Power Sources · doi:10.1016/j.jpowsour.2024.235634 · Cited by 124
Self-citationInan, T. Y., Doğan, H., Unveren, E. E., & Eker, E. (2010) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2010.07.084 · Cited by 117
SPEEK proton exchange membranes modified with silica sulfuric acid nanoparticles
Du, L., Yan, X., He, G., Wu, X., Hu, Z., & Wang, Y. (2012) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2012.05.024 · Cited by 113
Wu, C., Zhang, W., Han, X., Zhang, Y. X., & Ma, G. (2020) · Journal of Power Sources · doi:10.1016/j.jpowsour.2020.228724 · Cited by 103
Salarizadeh, P., Javanbakht, M., Pourmahdian, S., Hazer, M. S. A., Hooshyari, K., & Askari, M. B. (2018) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2018.11.235 · Cited by 102
SPE water electrolysis with SPEEK/PES blend membrane
Wei, G., Xu, L., Huang, C., & Wang, Y. (2010) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2010.05.041 · Cited by 100
Liu, X., Yang, Z., Zhang, Y., Li, C., Dong, J., Liu, Y., & Cheng, H. (2017) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2017.02.128 · Cited by 95
Meng, X., Mei, J., Tang, X., Jiang, J., Sun, C., & Song, K. (2024) · Energies · doi:10.3390/en17123050 · Cited by 91
Self-citationJun, M.-S., Choi, Y.-W., & Kim, J.-D. (2012) · Journal of Membrane Science · doi:10.1016/j.memsci.2011.12.008 · Cited by 88
Song, Y., Yang, M., Sun, C., & Xu, S. (2023) · Energies · doi:10.3390/en16166010 · Cited by 85
Self-citationLau, W. J., & Ismail, A. F. (2009) · Journal of Membrane Science · doi:10.1016/j.memsci.2009.02.012 · Cited by 83
Li, X., & Gao, J. (2022) · SusMat · doi:10.1002/sus2.88 · Cited by 83
Two-phase flow in GDL and reactant channels of a proton exchange membrane fuel cell
Kandlikar, S. G., See, E. J., Koz, M., Gopalan, P., & Banerjee, R. (2014) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2014.02.045 · Cited by 70
Fabrication of high-performance gas-diffusion-electrode based membrane-electrode assemblies
Mauger, S. A., Pfeilsticker, J. R., Wang, M., Medina, S., Yang-Neyerlin, A. C., Neyerlin, K. C., Stetson, C., Pylypenko, S., & Ulsh, M. (2020) · Journal of Power Sources · doi:10.1016/j.jpowsour.2019.227581 · Cited by 67
Okur, O., Karadağ, Ç. İ., San, F. G. B., Okumuş, E., & Behmenyar, G. (2013) · Energy · doi:10.1016/j.energy.2013.05.001 · Cited by 65
Li, J., Cui, N., Liu, D., Zhao, Z., Yang, F., Zhong, J., & Pang, J. (2024) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2023.08.334 · Cited by 65
Yin, Z., Geng, H., Yang, P., Shi, B., Fan, C., Peng, Q., Wu, H., & Jiang, Z. (2021) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2021.05.119 · Cited by 63
Meng, X., Liu, M., Mei, J., Li, X., Grigoriev, S. V., Hasanien, H. M., Tang, X., Li, R., & Sun, C. (2025) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2025.150162 · Cited by 62
Self-citationTang, X., Shi, L., Li, M., Xu, S., & Sun, C. (2024) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2024.3502499 · Cited by 57
Self-citationZhang, Y., Zhang, A., Wang, S., & Li, S. (2023) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2022.12.332 · Cited by 57
Han, M., Zhang, G., Li, M., Wang, S., Zhang, Y., Li, H., Lew, C. M., & Na, H. (2010) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2010.11.065 · Cited by 56
Advancements in printed components for proton exchange membrane fuel cells: A comprehensive review
da Costa, G. P., Garcia, D. M. E., Nguyen, T. H. V., Lacharmoise, P. D., & Simao, C. D. (2024) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2024.05.072 · Cited by 55
The Influence of the Gas Diffusion Layer on Water Management in Polymer Electrolyte Fuel Cells
Holmström, N., Ihonen, J., Lundblad, A., & Lindbergh, G. (2007) · Fuel Cells · doi:10.1002/fuce.200700003 · Cited by 52 · cited 1×
“Finally, the cathode side is immersed in water for a long time, so that oxygen cannot quickly reach the active sites of the catalyst, thereby slowing down the redox reaction and greatly reducing the performance of the membrane [60].”
3D effects of water-saturation distribution on polymeric electrolyte fuel cell (PEFC) performance
Cordiner, S., Lanzani, S. P., & Mulone, V. (2010) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2010.09.063 · Cited by 49
Ghasemi, M., Daud, W. R. W., Alam, J., Jafari, Y., Sedighi, M., Aljlil, S. A., & Ilbeygi, H. (2015) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2015.10.029 · Cited by 48
Kim, M. J., Ko, H., Nam, S. Y., & Kim, K. (2021) · Polymers · doi:10.3390/polym13203520 · Cited by 44
Thermal crosslinked and nanodiamond reinforced SPEEK composite membrane for PEMFC
Hou, H., Polini, R., Vona, M. L. D., Liu, X., Sgreccia, E., Chailan, J., & Knauth, P. (2013) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2012.12.019 · Cited by 43
Wu, Y., He, G., Wu, X., Yuan, Q., Gong, X., Zhen, D., & Sun, B. (2019) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2019.01.281 · Cited by 40
Wang, X., Zhao, S., Wang, S., Hou, X., Yang, J., Liang, C., Zhao, Y., Wang, L., Shen, C., Gao, N., et al. (2024) · Journal of Membrane Science · doi:10.1016/j.memsci.2024.123605 · Cited by 21
Jo, S.-W., Park, J. E., Jeong, H. Y., Yuk, M., So, S., Yu, D. M., Jang, J.-K., Kim, H., Cho, Y., & Kim, T. (2022) · Journal of Power Sources · doi:10.1016/j.jpowsour.2023.233363 · Cited by 20
Boosting ion conduction in polymer blends by tailoring polymer phase separation
Liu, L., Wang, F., Zhang, J., Jiang, W., Yang, F., Hu, M., & Jiang, F. (2023) · Journal of Power Sources · doi:10.1016/j.jpowsour.2023.233005 · Cited by 19
Martínez-Casillas, D. C., Solorza, O., Mollá, S., Montero, Á., García‐Bernabé, A., & Compañ, V. (2018) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2018.09.217 · Cited by 11
Cited by
Zhou, C., Chu, D., Zeng, W., Cheng, J., & Fei, Z. (2026) · Fuel Cells · doi:10.1002/fuce.70115 · Cited by 24
Huang, M., Song, A., Ben, X., Ji, W., Pan, Y., & Rao, H. (2026) · Nanomaterials · doi:10.3390/nano16080446 · Cited by 3
Cellulose-based membranes for PEM fuel cells: Acidic durability and recent advances
Sannasi, V., Sarvalkar, P. D., & Jung, H.-Y. (2026) · Applied Energy · doi:10.1016/j.apenergy.2026.127628 · Cited by 3
Poly(ether ether ketone) Copolymers as Advanced Materials for Energy and Electronics
Faizal, A., Kandasubramanian, B., & Vaidya, K. S. (2026) · ACS Applied Engineering Materials · doi:10.1021/acsaenm.6c00090 · Cited by 2
Guo, Z., Mingming, G., Zhao, Y., Yinfeng, S., Ren, K., Taijing, O., Tsim, S., & Sun, C. (2026) · SSRN Electronic Journal · doi:10.2139/ssrn.6448473 · Cited by 1
Self-citation
Metadata
- Authors
- Song, Y., Guo, Z., Yin, J., Liu, M., Tolj, I., Grigoriev, S. A., Ge, M., & Sun, C.
- Affiliations
- Harbin Institute of Technology (CN)
- Beijing Normal-Hong Kong Baptist University (CN)
- Shenzhen University (CN)
- University of Split (HR)
- National Research University “Moscow Power Engineering Institute”, 14, Krasnokazarmennaya St., Moscow 111250, Russia
- Corresponding author
- Yin, Jiayi
- Sun, Chuanyu
- Venue
- Polymers
- Publisher
- MDPI AG
- Published
- 2025-08-09
- Volume
- 17
- Issue
- 16
- Pages
- 2181
- ISSN
- 2073-4360 (ISSN-L)
- PMC
- PMC12389468
- OpenAlex
- W4413200649
- Semantic Scholar
- 2ca92def967ec0e14e9d6ba98496ebfe91f60bc2
- Cited by
- 28
- References
- 60
- Citations by year
- 2026: 25 · 2025: 3
- FWCI
- 6.22
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Polymers (publishedVersion, cc-by)
- Europe PMC (PubMed Central) (publishedVersion, cc-by)
- PubMed Central (publishedVersion, cc-by)
- PubMed (publishedVersion)
- Funders
- 2023 Youth Talent Introduction Scientific Research Startup Fee (AUGA2160100623, AUGA2160501723, 2024A1515010711, UICR0700117-25, ZJ2023023)
- 2023 Support Funds for Talent Introduction in Heilongjiang Province (AUGA2160100623, AUGA2160501723, 2024A1515010711, UICR0700117-25, ZJ2023023)
- GuangDong Basic and Applied Basic Research Foundation (AUGA2160100623, AUGA2160501723, 2024A1515010711, UICR0700117-25, ZJ2023023)
- UIC research fund (AUGA2160100623, AUGA2160501723, 2024A1515010711, UICR0700117-25, ZJ2023023)
- Priority Postdoctoral Projects in Zhejiang Province (AUGA2160100623, AUGA2160501723, 2024A1515010711, UICR0700117-25, ZJ2023023)
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Fuel Cells and Related Materials
- Physical Sciences › Chemical Engineering › Filtration and Separation › Membrane-based Ion Separation Techniques
- Physical Sciences › Materials Science › Materials Chemistry › Advancements in Solid Oxide Fuel Cells
- Keywords
- sulfonated poly(ether ether ketone), SPEEK membranes, degree of sulfonation, proton exchange membrane fuel cells, membrane durability, chemical stability, thermal stability, proton conductivity, swelling ratio, water absorption, power density
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.