The DOI matches its Crossref record; 126 of the 126 references it cites were found in a registry or an index; 21 of the 134 sources its claims cite were checked for support.
Electrochemical Direct Lithium Extraction: A Review of Electrodialysis and Capacitive Deionization Technologies
Open accessAbstract
The rapid expansion of lithium-ion battery (LIB) markets for electric vehicles and renewable energy storage has exponentially increased lithium demand, driving research into sustainable extraction methods. Traditional lithium recovery from brine using evaporation ponds is resource intensive, consuming vast amounts of water and causing severe environmental issues. In response, Direct Lithium Extraction (DLE) technologies have emerged as more efficient, eco-friendly alternatives. This review explores two promising electrochemical DLE methods: Electrodialysis (ED) and Capacitive Deionization (CDI). ED employs ion-exchange membranes (IEMs), such as cation exchange membranes, to selectively transport lithium ions from sources like brine and seawater and achieves high recovery rates. IEMs utilize chemical and structural properties to enhance the selectivity of Li+ over competing ions like Mg2+ and Na+. However, ED faces challenges such as high energy consumption, membrane fouling, and reduced efficiency in ion-rich solutions. CDI uses electrostatic forces to adsorb lithium ions onto electrodes, offering low energy consumption and adaptability to varying lithium concentrations. Advanced variants, such as Membrane Capacitive Deionization (MCDI) and Flow Capacitive Deionization (FCDI), enhance ion selectivity and enable continuous operation. MCDI incorporates IEMs to reduce co-ion interference effects, while FCDI utilizes liquid electrodes to enhance scalability and operational flexibility. Advancements in electrode materials remain crucial to enhance selectivity and efficiency. Validating these methods at the pilot scale is crucial for assessing performance, scalability, and economic feasibility under real-world conditions. Future research should focus on reducing operational costs, developing more durable and selective electrodes, and creating integrated systems to enhance overall efficiency. By addressing these challenges, DLE technologies can provide sustainable solutions for lithium resource management, minimize environmental impact, and support a low-carbon future.
Overview
CoChat Summary
TL;DR
This review examines electrochemical direct lithium extraction (DLE), focusing on electrodialysis (ED) and capacitive deionization (CDI) and their advanced variants. It synthesizes mechanisms, performance metrics, pilot-scale demonstrations, and challenges for sustainable lithium recovery from brine and seawater.
Key findings
- ED and CDI are both promising electrochemical DLE routes: ED uses ion-exchange membranes for high lithium recovery/selectivity, while CDI uses electrostatic adsorption with lower energy consumption and adaptability to varying lithium concentrations; MCDI and FCDI improve selectivity and enable continuous operation.
- ED examples include a modified CEM with Li/Na molar selectivity of 32.2 (62.3% higher than conventional CEM), BMED achieving 99.8% lithium removal and 86.4% recovery at 20 V, SED achieving 76.45% Li recovery with 0.66 kWh/mol Li at 10 V, and ILM-ED reducing Mg/Li from 50:1 to 0.5:1 with 65% current efficiency and 16 Wh·g⁻¹ Li.
- CDI examples include LMO/GO electrodes with a lithium separation factor of 47.8, 80% capacity retention after 150 cycles, and 720.2 µmol·g⁻¹ Li⁺ adsorption; MCDI with ZIF-8-PDA membranes showing Li/Na selectivity of 1.50 and Li/K of 1.85 at 0.5 V; FCDI Li-MFCDI showing Li/Na selectivity of 141 and Li/K of 46 with 16.70 kWh/kg energy consumption; and HCDI with β Li/Mg of 2.14 and over 70% lithium release efficiency.
- Pilot-scale results include ED with an average flux of 5.73 mol·m⁻²·h⁻¹ and 0.15 kWh/mol, ED enriching Li⁺ from 0.035 mM to 62 mM with purity rising from 0.0048% to 88% and an enrichment factor of 1800 at 0.25 m³/h, and CDI reducing feed salinity from 1 g/L to 0.5 g/L at about 200 L/h with 0.85–0.9 V and approximately 30% energy recovery.
Methods
- Design: narrative review of electrochemical DLE, with emphasis on ED and CDI, covering conventional lithium extraction, electrochemical mechanisms, advanced variants, pilot-scale case studies, and future research directions.
- Data: literature search via Google Scholar using keywords “lithium” and “direct lithium extraction” for 2012–2023; tables compile prior ED/CDI studies and pilot-scale results.
- Analysis: comparative synthesis of process parameters such as lithium source, flow rate, applied voltage, recovery ratio, separation/selectivity factors, adsorption capacity, and energy consumption; no primary experiments were conducted.
Limitations
- Stated: ED faces high energy consumption, membrane fouling/scaling, concentration polarization, high installation and operational costs, and periodic membrane replacement; CDI has limited effectiveness for high-salinity brine, electrode lifespan limits, co-ion expulsion, and is not yet mature for very large-scale desalination.
- Stated: pilot-scale barriers include fouling/scaling, declining energy efficiency with increasing salinity, and the cost and durability of ion-exchange membranes and high-surface-area electrodes.
- Evident from the text: as a narrative review, it does not report a systematic search protocol or quality appraisal, and many table entries are “N.A.” while performance comparisons span heterogeneous feed solutions and operating conditions, limiting direct comparability.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures
![Figure 1 Graphical representation of world lithium reserves created by the authors based on data Figure 1. Graphical representation of world lithium reserves created by the authors based on data from [8].](https://figures.cochat.ai/paper-figures/96cf954654a245069fdc16ddd2757d7e/electrochemical-direct-lithium-extraction-a-review-of-electrodialysis-and-figure-1.png)





Verification
Claims the paper makes
19 Valid · 3 Not valid · 91 Not checked · 29 Own results and interpretations
Every source the paper cites for this claim was checked and supports it.
In the paper
“However, conventional lithium extraction methods result in 85-95% water loss from brine, raising significant concerns about their impact on the water balance and biodiversity of Salt Lake ecosystems [17].”
What the sources say
- Supportedcites [17] Flexer, 2018, Lithium recovery from brines: A vital raw material for green energies with a potential environmental impact in its mining and processing, Sci. Total Environ. source
The paper’s section on sustainability issues (pp. 7–9) identifies water use and flora and fauna conservation as concerns with conventional evaporative extraction. It says that changes to the region’s water balance could affect local flora and fauna; it presents this as a potential impact, not an established loss of biodiversity. (LLM, conf=0.92)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“However, conventional lithium extraction methods result in 85-95% water loss from brine, raising significant concerns about their impact on the water balance and biodiversity of Salt Lake ecosystems [17].”
What the sources say
- Partly supportedcites [17] Flexer, 2018, Lithium recovery from brines: A vital raw material for green energies with a potential environmental impact in its mining and processing, Sci. Total Environ. sourceExperimental — accuracy not yet measured
Section 5, “Sustainability issues of the evaporitic technology” (page unavailable), says that up to 95% of the original brine water needs to be evaporated in conventional processing. It does not give an 85% lower bound or establish 85–95% as the usual range. The section also treats effects on the water balance as dependent on local conditions, rather than a uniform consequence. (LLM, conf=0.86)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“However, the adsorption process has the drawback of performance degradation in ion-sieve materials over time, resulting in reduced efficiency and increased operational costs due to frequent replacements [35].”
What the sources say
- Partly supportedcites [35] Murphy, O., and Haji, M.N. (2022). A Review of Technologies for Direct Lithium Extraction from Low Li+ Concentration Aqueous Solutions. Front. Chem. Eng., 30. sourceExperimental — accuracy not yet measured
Section 6, “Lithium-ion sieve adsorption,” says ion sieves can disintegrate during adsorption/desorption cycling, reducing adsorption capacity and separation efficiency. It also says operating costs rise because more sieve is needed to compensate for those losses, but it does not establish that replacements are frequent. (LLM, conf=0.84)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“ED systems are known for their high initial installation costs and significant energy consumption when processing high-concentration brine”
What the sources say
- Partly supportedcites [71] Dammak, L., Fouilloux, J., Bdiri, M., Larchet, C., Renard, E., Baklouti, L., Sarapulova, V., Kozmai, A., and Pismenskaya, N. (2021). A Review on Ion-Exchange Membrane Fouling during the Electrodialysis Process in the Food Industry, Part 1: Types, Effects, Characterization Methods, Fouling Mechanisms and Interactions. Membranes, 11. sourceExperimental — accuracy not yet measured
The Introduction and Conclusions say that membrane fouling can increase ED energy consumption. They do not link that increase to processing high-concentration brine; the Introduction instead describes electricity consumption in desalination as acceptable. Searches for high-concentration brine and high-salinity energy use found no supporting passage. (LLM, conf=0.84)
boostedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“ED systems are known for their high initial installation costs and significant energy consumption when processing high-concentration brine”
What the sources say
- Could not verifycites [71] Dammak, L., Fouilloux, J., Bdiri, M., Larchet, C., Renard, E., Baklouti, L., Sarapulova, V., Kozmai, A., and Pismenskaya, N. (2021). A Review on Ion-Exchange Membrane Fouling during the Electrodialysis Process in the Food Industry, Part 1: Types, Effects, Characterization Methods, Fouling Mechanisms and Interactions. Membranes, 11. sourceExperimental — accuracy not yet measured
The Conclusions (page unavailable) call ion-exchange membranes the most expensive component of ED modules, but do not discuss initial installation costs. Searches for installation and capital costs found no passage establishing that ED systems have high upfront costs. (LLM, conf=0.72)
boosted- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Could not verify
100 more claims · 11 with their cited sources checked
Create a free account to see all 142 claims and to verify the 1 reference still open.
- It may state two separate claims as one. 26
- Probably not a substantial claim. 18
Citations
Cites
Ghaffour, N., Missimer, T. M., & Amy, G. L. (2013) · Desalination · doi:10.1016/j.desal.2012.10.015 · Cited by 1,603 · cited 1×
“Specifically, CDI achieves an energy consumption of less than 0.5–2.5 kWh/m 3 when treating water with TDS concentrations below 2000 mg/L, making it highly efficient compared to traditional desalination methods such as reverse osmosis [23,25,26].”
InfluentialElectrodialysis, a mature technology with a multitude of new applications
Strathmann, H. (2010) · Desalination · doi:10.1016/j.desal.2010.04.069 · Cited by 1,545
Ion exchange membranes: State of their development and perspective
Xu, T. (2005) · Journal of Membrane Science · doi:10.1016/j.memsci.2005.05.002 · Cited by 1,364 · cited 2×
“In selective dialysis (SED), monovalent-selective ion exchange membranes (IEMs used to replace standard IEMs in conventional ED systems SED is a separation process based on ion-exchange membranes, offering high selectivity and making it essential for the separation of ionic species [65,66].”
Oren, Y. (2008) · Desalination · doi:10.1016/j.desal.2007.08.005 · Cited by 1,180
Tong, T., & Elimelech, M. (2016) · Environmental Science & Technology · doi:10.1021/acs.est.6b01000 · Cited by 1,126 · cited 1×
“However, ED also consumes more energy, requiring approximately 7–15 kWh/m 3 of feed water to concentrate brine to high salinity levels [72].”
Electrodialysis desalination for water and wastewater: A review
Al-Amshawee, S., Yunus, M. Y. B. M., Azoddein, A. A. M., Hassell, D. G., Dakhil, I. H., & Hasan, H. A. (2020) · Chemical Engineering Journal · doi:10.1016/j.cej.2019.122231 · Cited by 964
Anderson, M. A., Cudero, A. L., & Palma, J. (2010) · Electrochimica Acta · doi:10.1016/j.electacta.2010.02.012 · Cited by 943 · cited 1×
“Additionally, their energy efficiency decreases with increasing salinity; CDI, in particular, requires significant energy for electrode regeneration, making it less competitive than reverse osmosis in high-salinity contexts [115].”
Grosjean, C., Miranda, P. H., Perrin, M., & Poggi, P. (2012) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2011.11.023 · Cited by 847 · cited 2×
“Among them, Chile stands out with 34%, making it the leading country in lithium reserves and a key player in lithium production [7,8].”
Flexer, V., Baspineiro, C. F., & Galli, C. I. (2018) · Science of the Total Environment · doi:10.1016/j.scitotenv.2018.05.223 · Cited by 768 · cited 4×
“Additionally, it requires extensive land areas and is highly dependent on climatic conditions, leading to low predictability and sustainability [17].”
InfluentialEnvironmental impact of direct lithium extraction from brines
Vera, M. L., Torres, W. R., Galli, C. I., Chagnes, A., & Flexer, V. (2023) · Nature Reviews Earth & Environment · doi:10.1038/s43017-022-00387-5 · Cited by 766 · cited 2×
“By 2030, EV demand is expected to reach 142 million units, with lithium carbonate demand projected to rise to 3–4 million metric tons (Mt) [9,10].”
Research works printed but not linked: 1
- Joo, 2023, Electrochemical Ion Separation Technology for Carbon Neutrality, Appl. Chem. Eng., 34, 331
Cited by
Advances in integrated membrane processes for sustainable lithium extraction
Tufa, R. A., Santoro, S., Flores-Fernández, C., Zegeye, R. B., Fuentealba, D., Aquino, M., Barraza, B., Inzillo, B. M., Nasirov, S., D'Andrea, G., et al. (2025) · Desalination · doi:10.1016/j.desal.2025.118899 · Cited by 37
Khan, S., Rahman, S. U., Shah, A., Akhtar, N., Hussain, Z., Ahmad, N., Kamika, I. A., Azizi, S., & Mâaza, M. (2026) · Desalination · doi:10.1016/j.desal.2026.119860 · Cited by 25
Han, S. A., Kim, H., Son, J., Ha, J., & Jo, C. (2026) · Chemical Engineering Journal · doi:10.1016/j.cej.2026.173831 · Cited by 16
Recovering Critical Metals from Brines: Technology Landscape, Circular Economy, and Future Trends
Abedi, M., Chang, A., Hassan, H. I., Yang, A., Hickethier, M., Bushagour, A., Aghajari, M. J., Stoerzinger, K. A., Layton, A., Abbasi, B., et al. (2026) · ACS Applied Energy Materials · doi:10.1021/acsaem.5c03407 · Cited by 21
Yelatontsev, D. O., Mukhachev, A. P., & Shevchenkо, V. (2025) · Desalination · doi:10.1016/j.desal.2025.119558 · Cited by 12
Metadata
- Authors
- Park, J., Lee, J., Shim, I.-T., Kim, E., Nam, S.-H., Koo, J.-W., & Hwang, T.-M.
- Affiliations
- Korea Institute of Civil Engineering and Building Technology (KR)
- Western University (CA)
- Department of Civil and Environmental Engineering, Korea University of Science & Technology, 217 Gajung-Ro, Yuseong-Gu, Daejeon 34113, Republic of Korea
- Corresponding author
- Hwang, Tae-Mun
- Venue
- Resources
- Publisher
- MDPI AG
- Published
- 2025-02-03
- Volume
- 14
- Issue
- 2
- Pages
- 27
- ISSN
- 2079-9276 (ISSN-L)
- OpenAlex
- W4407085251
- Cited by
- 44
- References
- 121
- Citations by year
- 2026: 37 · 2025: 7
- FWCI
- 10.77
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Resources (publishedVersion, cc-by)
- RePEc: Research Papers in Economics (submittedVersion)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Funders
- Ministry of Land, Infrastructure, and Transport (RS-2022-00144137, 20240065-001)
- KICT Research Program (RS-2022-00144137, 20240065-001)
- Ministry of Science and ICT (RS-2022-00144137, 20240065-001)
- Topics
- Physical Sciences › Chemical Engineering › Filtration and Separation › Membrane-based Ion Separation Techniques
- Physical Sciences › Materials Science › Metals and Alloys › Extraction and Separation Processes
- Physical Sciences › Environmental Science › Water Science and Technology › Membrane Separation Technologies
- Keywords
- direct lithium extraction, electrodialysis, capacitive deionization, lithium recovery, lithium brines, ion exchange membranes, cation exchange membrane, membrane fouling, electrode materials, membrane capacitive deionization, lithium-ion batteries
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-12, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-12 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Electrochemical Direct Lithium Extraction: A Review of Electrodialysis and Capacitive Deionization Technologies. https://app.cochat.ai/papers/10.3390/resources14020027
- The paper
- Park, J., Lee, J., Shim, I.-T., Kim, E., Nam, S.-H., Koo, J.-W., & Hwang, T.-M. (2025). Electrochemical Direct Lithium Extraction: A Review of Electrodialysis and Capacitive Deionization Technologies. Resources. https://doi.org/10.3390/resources14020027
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.