Dynamic Mechanical Properties and Thermal Stability of Poly(lactic Acid) and Poly(butylene Succinate) Blends Composites
The DOI matches its Crossref record; 37 of the 37 references it cites were found in a registry or an index.
Abstract
The blend of poly(lactic acid) (PLA) and poly(butylene succinate) (PBS) were prepared and extruded with various compositions and their molded properties were examined. Thermogravimetric analysis showed that thermal stability of the blends was higher than that of pure PLA and the weight loss of PLA/PBS (40/60 wt%) was lower than neat polymers. Difierential scanning calorimetry thermograms of blends indicated that the thermal properties of PLA did not change noticeably when blended with PBS. The tensile strength and modulus of blends decreased with the increasing PBS content. But impact strength has improved about two times compared to pure PLA. Rheological results revealed that the addition of 10% and 20% of PBS increased the storage modulus, loss modulus and viscosity of the blend at nearly all frequencies, and decreased viscosity with increasing shear stress. Dynamic mechanical properties results showed the lowering of storage modulus of all blended PLA which indicated the increase of molecular mobility by adding PBS due to lower glass transition.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Citations
Cites
Processing technologies for poly(lactic acid)
Lim, L.-T., Auras, R., & Rubino, M. (2008) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2008.05.004 · Cited by 2,766
Jain, R. A. (2000) · Biomaterials · doi:10.1016/s0142-9612(00)00115-0 · Cited by 2,214 · cited 1×
“Biodegradable PLA is perhaps the most important polyester in biomedical applications [9, 10].”
Polymer blends and composites from renewable resources
Yu, L., Dean, K., & Li, L. (2006) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2006.03.002 · Cited by 2,107
Poly(lactic acid) fiber: An overview
Gupta, B., Revagade, N., & Hilborn, J. (2007) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2007.01.005 · Cited by 1,360 · cited 1×
“PLA has attracted an increasing interest in various markets, such as packaging, textile [11-15], and automotive industries [16, 17].”
Poly(lactide) Stereocomplexes: Formation, Structure, Properties, Degradation, and Applications
Tsuji, H. (2007) · Macromolecular Bioscience · doi:10.1002/mabi.200700275 · Cited by 1,021
Research progress in toughening modification of poly(lactic acid)
Liu, H., & Zhang, J. (2011) · Journal of Polymer Science Part B: Polymer Physics · doi:10.1002/polb.22283 · Cited by 767 · cited 1×
“Among a few commercially available biobased or partially biobased thermoplastic polymers, poly(lactic acid) (PLA) has been investigated extensively [2, 3].”
Thermal characterization of polylactides
Jamshidi, K., Hyon, S.-H., & Ikada, Y. (1988) · Polymer · doi:10.1016/0032-3861(88)90116-4 · Cited by 692
New polylactide/layered silicate nanocomposites. 1. Preparation, characterization, and properties
Sinha Ray, S., Maiti, P., Okamoto, M., Yamada, K., & Ueda, K. (2002) · Macromolecules · doi:10.1021/ma011613e · Cited by 607 · cited 1×
“It is a linear aliphatic thermoplastic polyester, produced from renewable resources with good biocompatibility, non-toxic byproducts, excellent transparency, and high strength and modulus [4-8].”
Structure and properties for biomass-based polyester blends of PLA and PBS
Yokohara, T., & Yamaguchi, M. (2008) · European Polymer Journal · doi:10.1016/j.eurpolymj.2008.01.008 · Cited by 439
New Polylactide/Layered Silicate Nanocomposites, 6
Sinha Ray, S., & Okamoto, M. (2003) · Macromolecular Materials and Engineering · doi:10.1002/mame.200300156 · Cited by 333
Cited by
Farah, S., Anderson, D. G., & Langer, R. (2016) · Advanced Drug Delivery Reviews · doi:10.1016/j.addr.2016.06.012 · Cited by 3,443
Polylactic acid blends: The future of green, light and tough
Hamad, K., Kaseem, M., Ayyoob, M., Joo, J., & Deri, F. (2018) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2018.07.001 · Cited by 640
Poly(butylene succinate) (PBS): Materials, processing, and industrial applications
Barletta, M., Aversa, C., Ayyoob, M., Gisario, A., Hamad, K., Mehrpouya, M., & Vahabi, H. (2022) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2022.101579 · Cited by 443
A Review on Properties and Application of Bio-Based Poly(Butylene Succinate)
Rafiqah, S. A., Khalina, A., Harmaen, A. S., Tawakkal, I. A., Zaman, K., Asim, M., Nurrazi, M. N., & Lee, C. H. (2021) · Polymers · doi:10.3390/polym13091436 · Cited by 398
Blending poly(butylene succinate) with poly(lactic acid): Ductility and phase inversion effects
Deng, Y., & Thomas, N. L. (2015) · European Polymer Journal · doi:10.1016/j.eurpolymj.2015.08.029 · Cited by 191
“Hassan et al [13] found that strain-to-break of PLA/PBS blends increased gradually with increasing PBS content, although high ductilities were only reached at PBS levels in excess of 80 weight %.”
BackgroundKian, L. K., Saba, N., Jawaid, M., & Sultan, M. T. H. (2019) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2018.09.040 · Cited by 174
Tyagi, P., Agate, S., Velev, O. D., Lucia, L. A., & Pal, L. (2022) · Environmental Science & Technology · doi:10.1021/acs.est.1c04710 · Cited by 168
Shape memory effect in 3D-printed scaffolds for self-fitting implants
Senatov, F. S., Zadorozhnyy, M. Y., Niaza, K. V., Medvedev, V. V., Kaloshkin, S. D., Anisimova, N. Y., Kiselevskiy, M., & Yang, K.-C. (2017) · European Polymer Journal · doi:10.1016/j.eurpolymj.2017.06.011 · Cited by 149
Liminana, P., Sanoguera, D. G., Quiles‐Carrillo, L., Balart, R., & Muñoz, N. M. (2018) · Composites Part B Engineering · doi:10.1016/j.compositesb.2018.02.031 · Cited by 146
Tábi, T., Ageyeva, T., & Kovács, J. G. (2021) · Polymer Testing · doi:10.1016/j.polymertesting.2021.107282 · Cited by 119
Andrzejewski, J., Cheng, J., Anstey, A., Mohanty, A. K., & Misra, M. (2020) · ACS Sustainable Chemistry & Engineering · doi:10.1021/acssuschemeng.9b04925 · Cited by 124
Aliotta, L., Cinelli, P., Coltelli, M., & Lazzeri, A. (2018) · European Polymer Journal · doi:10.1016/j.eurpolymj.2018.12.042 · Cited by 120
Oesterreicher, A., Wiener, J., Roth, M., Moser, A., Gmeiner, R., Edler, M., Pinter, G., & Grießer, T. (2016) · Polymer Chemistry · doi:10.1039/c6py01132b · Cited by 117
Abdullah, T., Saeed, U., Memić, A., Gauthaman, K., Hussain, M. A., & Al-Turaif, H. (2019) · Journal of Polymer Research · doi:10.1007/s10965-019-1772-y · Cited by 97
Poly(lactic acid) and Its Blends for Packaging Application: A Review
Luca, S. D., Milanese, D., Nottiani, D. G., Cavazza, A., & Sciancalepore, C. (2023) · Clean Technologies · doi:10.3390/cleantechnol5040066 · Cited by 100
Shojaeiarani, J., Bajwa, D. S., & Stark, N. M. (2018) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2018.02.069 · Cited by 92
Ostrowska, J., Sadurski, W., Paluch, M., Tyński, P., & Bogusz, J. (2019) · Polymer International · doi:10.1002/pi.5814 · Cited by 85
Aliotta, L., Vannozzi, A., Canesi, I., Cinelli, P., Coltelli, M., & Lazzeri, A. (2021) · Polymers · doi:10.3390/polym13020218 · Cited by 88
“PBSA is produced by a polycondensation reaction of 1,4-butanediol with succinic acid and adipic acid, that produces a completely aliphatic polyester having high flexibility, excellent impact strength, as well as thermal and chemical resistance and good biodegradability [11,23].”
BackgroundReview on PCL, PBS, and PCL/PBS blends containing carbon nanotubes
Gumede, T. P., Luyt, A. S., & Muller, A. J. (2018) · Express Polymer Letters · doi:10.3144/expresspolymlett.2018.43 · Cited by 80
Rheological properties of cellulose nanocrystals engineered polylactic acid nanocomposites
Shojaeiarani, J., Bajwa, D. S., Stark, N. M., & Bajwa, S. G. (2019) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2018.12.128 · Cited by 76
Stoyanova, N., Paneva, D., Mincheva, R., Toncheva, A., Manolova, N. E., Dúbois, P., & Rashkov, I. B. (2014) · Materials Science and Engineering C · doi:10.1016/j.msec.2014.04.043 · Cited by 82
Singla, R. K., Zafar, M. T., Maiti, S. N., & Ghosh, A. K. (2017) · Polymer Testing · doi:10.1016/j.polymertesting.2017.08.042 · Cited by 77
Lila, M. K., Kartikeya, K., Komal, U. K., & Singh, I. (2018) · Composites Part B Engineering · doi:10.1016/j.compositesb.2018.08.068 · Cited by 73
Lule, Z. C., & Kim, J. (2019) · Polymers · doi:10.3390/polym11010148 · Cited by 71
Vorawongsagul, S., Pratumpong, P., & Pechyen, C. (2020) · Food Packaging and Shelf Life · doi:10.1016/j.fpsl.2020.100608 · Cited by 73
Chuayjuljit, S., Wongwaiwattanakul, C., Chaiwutthinan, P., & Prasassarakich, P. (2016) · Polymer Composites · doi:10.1002/pc.23886 · Cited by 72
Rashmi, B. J., Prashantha, K., Lacrampe, M., & Krawczak, P. (2015) · eXPRESS Polymer Letters · doi:10.3144/expresspolymlett.2015.67 · Cited by 63
Melt processing of biodegradable poly(butylene succinate) (PBS)—a critical review
Barletta, M., Genovesi, A., Desole, M. P., & Gisario, A. (2024) · Clean Technologies and Environmental Policy · doi:10.1007/s10098-024-03005-8 · Cited by 64
“Muhuo (2013) studied injection molding of PLA/PBS blends by exploring the entire compositional range.”
Srivastava, A., Bhati, P., Singh, S., Agrawal, M., Kumari, N., Vashisth, P., Chauhan, P., & Bhatnagar, N. (2024) · Polymer Engineering and Science · doi:10.1002/pen.26626 · Cited by 52
Ghorbani, M., Vakili, M. H., & Ameri, E. (2021) · Materials Today Communications · doi:10.1016/j.mtcomm.2021.102560 · Cited by 51
Characterization of Natural Composites Fabricated from Abutilon-Fiber-Reinforced Poly (Lactic Acid)
Wang, H., Hassan, E. A. M., Memon, H., Elagib, T. H. H., & AllaIdris, F. A. (2019) · Processes · doi:10.3390/pr7090583 · Cited by 46
Self-citationLule, Z. C., Ju, H., & Kim, J. (2018) · Ceramics International · doi:10.1016/j.ceramint.2018.09.066 · Cited by 43
Somsunan, R., & Mainoiy, N. (2019) · Journal of Thermal Analysis and Calorimetry · doi:10.1007/s10973-019-08631-9 · Cited by 44
Hassan, E. A. M., Elarabi, S., Wei, Y., & Yu, M. (2017) · Textile Research Journal · doi:10.1177/0040517517708538 · Cited by 39
Self-citationSeo, Y.-R., Bae, S.-U., Gwon, J., Wu, Q., & Kim, B. (2020) · Materials · doi:10.3390/ma13071660 · Cited by 36
“The first- nd 284 s cond-stage peak axim m temperatures refer to TMax1 by the thermal decomposition of PLA 285 WF and TMax2 by the thermal decomposition of PBS, respectively [28].”
BackgroundMethodZhang, K., Shang, S., Yu, Z. H., Wei, L., & Zhu, P. (2024) · ACS Applied Polymer Materials · doi:10.1021/acsapm.3c02516 · Cited by 36
Singla, R. K., Maiti, S. N., & Ghosh, A. K. (2016) · Journal of Materials Science · doi:10.1007/s10853-016-0255-3 · Cited by 34
Tan, L., & Qu, J. (2019) · Polymer Testing · doi:10.1016/j.polymertesting.2019.05.005 · Cited by 35
Ramlee, N. A., & Tominaga, Y. (2019) · Polymer · doi:10.1016/j.polymer.2019.01.043 · Cited by 31
Yoksan, R., & Dang, K. M. (2023) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2023.123332 · Cited by 33
Ucpinar, B., Sivrikaya, T., & Aytaç, A. (2025) · Polymer Composites · doi:10.1002/pc.29569 · Cited by 31
Pandey, K., Antil, R., Saha, S., Jacob, J., & Balavairavan, B. (2019) · Materials Research Express · doi:10.1088/2053-1591/ab5398 · Cited by 28
Elastomer–Hydrogel Systems: From Bio-Inspired Interfaces to Medical Applications
Fray, M. E., Demirci, G., Niedźwiedź, M., & Kantor-Malujdy, N. (2022) · Polymers · doi:10.3390/polym14091822 · Cited by 30
Lule, Z. C., & Kim, J. (2020) · European Polymer Journal · doi:10.1016/j.eurpolymj.2020.109849 · Cited by 26
Compatibilization of poly(lactic acid)/epoxidized natural rubber blend with maleic anhydride
Klinkajorn, J., & Tanrattanakul, V. (2019) · Journal of Applied Polymer Science · doi:10.1002/app.48297 · Cited by 26
Sabalina, A., Gaidukovs, S., Platnieks, O., Starkova, O., Gaidukova, G., Orlova, L., & Jurinovs, M. (2025) · RSC Sustainability · doi:10.1039/d5su00275c · Cited by 25
Shahdan, D., Flaifel, M. H., Chen, S., Ahmad, S., & Hassan, A. (2019) · Bulletin of Materials Science · doi:10.1007/s12034-019-1782-8 · Cited by 25
Foaming behavior of bio‐based blends based on thermoplastic gelatin and poly(butylene succinate)
Oliviero, M., Sorrentino, L., Cafiero, L., Galzerano, B., Sorrentino, A., & Iannace, S. (2015) · Journal of Applied Polymer Science · doi:10.1002/app.42704 · Cited by 25
Fenni, S. E., Monticelli, O., Conzatti, L., Doufnoune, R., Stagnaro, P., Haddaoui, N., & Cavallo, D. (2017) · eXPRESS Polymer Letters · doi:10.3144/expresspolymlett.2018.5 · Cited by 25
“Introduction Poly(L-lactic acid) (PLLA) is an excellent environmental friendly plastic [1, 2], due to its high rigidity, biocompatibility and biodegradability [3, 4].”
Backgroundde Perre, D. V., Serbruyns, L., Coltelli, M., Gigante, V., Aliotta, L., Lazzeri, A., Geerinck, R., & Verstichel, S. (2024) · Materials · doi:10.3390/ma17225436 · Cited by 25
“It is biodegradable and has good properties, such as high flexibility, thermal and chemical resistance and good impact strength [20].”
Akindoyo, J. O., Husney, N. A. A. B., Ismail, N. H., & Mariatti, M. (2020) · Polymers and Polymer Composites · doi:10.1177/0967391120954047 · Cited by 25
Almwli, H. H. A., Mousavi, S. M., & Kiani, S. (2020) · Process Safety and Environmental Protection · doi:10.1016/j.cherd.2020.10.033 · Cited by 22
Faibunchan, P., Nakaramontri, Y., Chueangchayaphan, W., Pichaiyut, S., Kummerlöwe, C., Vennemann, N., & Nakason, C. (2018) · Journal of Polymers and the Environment · doi:10.1007/s10924-017-1173-4 · Cited by 21
Aldás, M., Ferri, J. M., Motoc, D. L., Peponi, L., Arrieta, M. P., & López, J. (2021) · Polymers · doi:10.3390/polym13121913 · Cited by 26
“By adding 0.3 phr of Luperox 101 to the PLA/20PBAT/20PBS formulation, it was possible to increase by up to 10 times the impact energy absorbed, with respect to the polymeric matrix without additives, considerably reducing the glass transition temperature, Tg, of PLA and increasing the elongation at break [26].”
InfluentialArif, P. M., Sarathchandran, C., Narayanan, A., Saiter, A., Terzano, R., Allegretta, I., Porfido, C., Kalarikkal, N., & Thomas, S. (2017) · Polymer Testing · doi:10.1016/j.polymertesting.2017.09.026 · Cited by 20
Holt, A., Ke, Y., Bramhall, J. A., Crane, G. H., Grubbs, J. B., White, E. M., Horn, J., & Locklin, J. (2021) · ACS Applied Polymer Materials · doi:10.1021/acsapm.1c00078 · Cited by 21
Boonprasertpoh, A., Pentrakoon, D., & Junkasem, J. (2017) · Cellular Polymers · doi:10.1177/026248931703600603 · Cited by 19
Thirmizir, M. Z. A., Ishak, Z. A. M., Taib, R. M., Sudesh, K., Salim, M. S., Hassan, A., & Bakar, M. B. A. (2021) · Journal of Vinyl and Additive Technology · doi:10.1002/vnl.21828 · Cited by 19
Silva, A. L., Corrêa, M. M., de Oliveira, G. C., Michel, R. C., Semaan, F. S., & Ponzio, E. A. (2018) · New Journal of Chemistry · doi:10.1039/c8nj03501f · Cited by 18
Sabalina, A., Gaidukovs, S., Jurinovs, M., Grase, L., & Platnieks, O. (2023) · Journal of Applied Polymer Science · doi:10.1002/app.54031 · Cited by 17
Sukthavorn, K., Ketruam, B., Nootsuwan, N., Jongrungruangchok, S., Veranitisagul, C., & Laobuthee, A. (2021) · Journal of Material Cycles and Waste Management · doi:10.1007/s10163-021-01269-6 · Cited by 17
“However, no one reported the use of the ground tea leaves (GTL) waste from consumption to make green composite fibers with biodegradable polymers, such as PLA, PBS, etc.”
BackgroundBarletta, M., Aversa, C., Puopolo, M., & Donninelli, A. (2018) · Polymer-Plastics Technology and Materials · doi:10.1080/03602559.2018.1520254 · Cited by 16
“[21] Shakoor and Thomas observed the same effect in their work and state that talc acted as a nucleating agent for the crystallization of PLA.”
BackgroundInfluentialTadda, M. A., Gouda, M., Lin, X., Shitu, A., Abdullahi, H. S., Zhu, S., Li, X., & Liu, D. (2021) · Frontiers in Materials · doi:10.3389/fmats.2021.768960 · Cited by 15
Cicogna, F., Passaglia, E., Benedettini, M., Oberhauser, W., Ishak, R., Signori, F., & Coiai, S. (2023) · Molecules · doi:10.3390/molecules28010347 · Cited by 15
“The composition of the blend was selected as it is optimized for application in the packaging industry [6,61]: indeed, this polymer ratio increases the elongation at break of PLA by about 40% and significantly improves its impact strength.”
BackgroundCasamento, F., D’Anna, A., Arrigo, R., & Frache, A. (2021) · Journal of Applied Polymer Science · doi:10.1002/app.50590 · Cited by 14
Slow relaxations in semicrystalline poly(butylene succinate) below and above Tg
Ramos, J. J. M., & Diogo, H. P. (2014) · Polymer Engineering and Science · doi:10.1002/pen.24027 · Cited by 14
Rashmi, B. J., Prashantha, K., Lacrampe, M., & Krawczak, P. (2016) · AIP conference proceedings · doi:10.1063/1.4942284 · Cited by 14
Kaymakçı, A., Ayrılmış, N., Güleç, T., & Tufan, M. (2016) · Journal of Composite Materials · doi:10.1177/0021998316674265 · Cited by 14
“Nurul and Mariatti(30) and Hassan et al.(31) reported that Xc improved tensile strength and modulus of PP, because the crystalline region acted as a physical crosslink that enhanced the tensile strength and their modulus of thermoplastic.”
BackgroundPajarito, B. B., Cayabyab, C. A. L., Costales, P. A. C., & Francisco, J. R. (2019) · Journal of Coatings Technology and Research · doi:10.1007/s11998-019-00188-4 · Cited by 13
Thermal Characterization of the Natural Fiber‐Based Hybrid Composites: An Overview
Muthukumar, C., Krishnasamy, S., Thiagamani, S. M. K., Rajini, N., & Siengchin, S. (2021) · Wiley eBooks · doi:10.1002/9783527831562.ch1 · Cited by 13
Hemsri, S., Thongpin, C., Moradokpermpoon, N., Niramon, P., & Suppaso, M. (2015) · Macromolecular Symposia · doi:10.1002/masy.201400129 · Cited by 12
Phiriyawirut, M., Sarapat, K., Sirima, S., & Prasertchol, A. (2019) · Open Journal of Polymer Chemistry · doi:10.4236/ojpchem.2019.91001 · Cited by 12
“Hassan and coworker [25] which studied the properties of injected PLA/PBS blend.”
BackgroundKadowaki, Y., & Kojio, K. (2022) · Journal of Polymer Research · doi:10.1007/s10965-022-02986-8 · Cited by 11
Effect of Thermoplastic Elastomer on Melt Rheological and Fracture Behavior of Poly(Lactic Acid)
Nehra, R., Maiti, S. N., & Jacob, J. (2017) · Polymer-Plastics Technology and Engineering · doi:10.1080/03602559.2017.1381240 · Cited by 11
“Hassan et al.([15]) reported that the addition of poly(butylene succinate) into PLA resulted in enhanced storage and loss modulus.”
BackgroundJohn, A., Črešnar, K. P., Stanley, J., Vohl, S., Makuc, D., Bikiaris, D. Ν., & Zemljič, L. F. (2025) · Polymer Testing · doi:10.1016/j.polymertesting.2025.108707 · Cited by 10
Tadda, M. A., Gouda, M., Shitu, A., Yu, Q., Zhao, X., Liu, Y., Zhu, S., & Liu, D. (2023) · Journal of environmental chemical engineering · doi:10.1016/j.jece.2023.109654 · Cited by 10
Modification of PLA with Chain Extender
Elhassan, A., Saeed, H. A. M., Eltahir, Y. A., Xia, Y. M., & Wang, Y. (2014) · Applied Mechanics and Materials · doi:10.4028/www.scientific.net/amm.716-717.44 · Cited by 10
“Derived from renewable, and degradable resources with good biocompatibility, excellent transparency non-toxic byproducts and high strength and modulus [3][4].”
BackgroundNucleation and Crystallization in Bio-Based Immiscible Polyester Blends
Fenni, S. E., Cavallo, D., & Müller, A. J. (2019) · Advances in polymer science · doi:10.1007/12_2019_48 · Cited by 10
Properties and Food Packaging Application of Poly‐(Lactic) Acid
Sari, N. H., Suteja, S., Sapuan, S. M., & Ilyas, R. A. (2021) · Wiley eBooks · doi:10.1002/9781119381228.ch14 · Cited by 14
Jariyasakoolroj, P., Makyarm, K., Klairasamee, K., Sane, A., & Jarupan, L. (2023) · Journal of Applied Polymer Science · doi:10.1002/app.53915 · Cited by 10
Barletta, M., & Puopolo, M. (2019) · Journal of Polymers and the Environment · doi:10.1007/s10924-019-01500-4 · Cited by 9
Shi, D., Jiali, S., Zhao, Z., Shi, C., & Chen, M. (2016) · Polymers · doi:10.3390/polym8030092 · Cited by 9
“physicochemical properties [11–15].”
Eco-friendly Polymer Composite: State-of-Arts, Opportunities and Challenge
Aigbodion, V. S., Okonkwo, E. G., & Akinlabi, E. T. (2019) · Springer eBooks · doi:10.1007/978-3-030-05399-4_42 · Cited by 9
Thummarungsan, N., Pattavarakorn, D., & Sirivat, A. (2016) · Journal of the mechanical behavior of biomedical materials/Journal of mechanical behavior of biomedical materials · doi:10.1016/j.jmbbm.2016.07.024 · Cited by 8
Thodsaratpreeyakul, W., Uawongsuwan, P., & Negoro, T. (2018) · Materials Sciences and Applications · doi:10.4236/msa.2018.91012 · Cited by 8
“The lower intensity of the tan delta peaks indicates better dispersion of the dispersed phase in RPET/PC blends [24] [25] [26], because there are more restrict the molecular mobility.”
BackgroundKim, D., Hikima, Y., & Ohshima, M. (2021) · Journal of Applied Polymer Science · doi:10.1002/app.51890 · Cited by 8
“PLA is often blended with other flexible and biodegradable polymers, such as poly(butylene succinate) (PBS)[18-28] and poly(butylene succinate-coadipate) (PBSA)[30-38].”
BackgroundGamma-Irradiated Gelatin-Based Films Modified by HEMA for Medical Application
Alam, J., Rahman, W., Mazid, R. A., & Khan, M. M. R. (2015) · International Journal of Polymer Analysis and Characterization · doi:10.1080/1023666x.2015.1035542 · Cited by 6
“In addition, blend specimens such as the blending system consisting of polylactic acid (PLA) and poly(butylene succinate) (PBS),([21]) polybutylene succinate (PBS) with crystalline polyester,([22]) polylactic acid with starch,([23]) polypropylene with polystyrene,([24]) and liquid crystalline polymer with polyethylene…”
MethodSchippers, C., Gutmann, J. S., & Tsarkova, L. (2022) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.2c16159 · Cited by 6
Parveez, B., Bakar, M. S. A., Aabid, A., & Baig, M. (2024) · Polymer-Plastics Technology and Materials · doi:10.1080/25740881.2024.2375366 · Cited by 9
Ilangovan, M., Kabe, T., & Iwata, T. (2023) · ACS Applied Polymer Materials · doi:10.1021/acsapm.3c01759 · Cited by 6
Rojas‐Lema, S., Martínez, J. I., Gómez-Caturla, J., Balart, R., & García‐García, D. (2021) · Journal of Applied Research in Technology & Engineering · doi:10.4995/jarte.2021.15727 · Cited by 6
Renoux, J., Dani, J., Douchain, C., Prashantha, K., & Krawczak, P. (2018) · Journal of Applied Polymer Science · doi:10.1002/app.46442 · Cited by 5
Ilangovan, M., Gan, H., Kabe, T., & Iwata, T. (2022) · Polymer · doi:10.1016/j.polymer.2022.125332 · Cited by 5
Suresh, S. S., Mohanty, S., & NAYAK, S. K. (2019) · Journal of Material Cycles and Waste Management · doi:10.1007/s10163-019-00961-y · Cited by 5
Güzel, K., Klute, M., Kurgan, N., & Heim, H. (2020) · AIP conference proceedings · doi:10.1063/1.5142934 · Cited by 5
Boonthamjinda, L., Petchwattana, N., Covavisaruch, S., Chinsirikul, W., & Kerddonfag, N. (2015) · Key engineering materials · doi:10.4028/www.scientific.net/kem.659.363 · Cited by 4
“Researchers had attempted to improve the thermal and mechanical properties of PLA by making PLA composites [1], PLA blends [2], PLA compounds [3] or by stretching [4,5].”
BackgroundKumar, G. M., & Soundararajan, P. V. K. S. (2017) · IOSR Journal of Polymer and Textile Engineering · doi:10.9790/019x-04011621 · Cited by 4
“In 2010, PLA was the second most important bioplastic of the world in regard to consumption volume and lot of research has been done on bio-degradable polymers based on PLA [1-5].”
BackgroundTechnological challenges and advances: from lactic acid to polylactate and copolymers
Coelho, L. F., Beitel, S. M., & Contiero, J. (2019) · Elsevier eBooks · doi:10.1016/b978-0-12-816901-8.00005-5 · Cited by 4
Hirsch, P., Menzel, M., Klehm, J., & Putsch, P. (2019) · Macromolecular Symposia · doi:10.1002/masy.201800167 · Cited by 4
Wang, J., Zhang, Y., Zuo, Y., Fu, Z., Jia, S., & Zhang, H. (2025) · Journal of Macromolecular Science Part A · doi:10.1080/10601325.2025.2514001 · Cited by 2
Metadata
- Authors
- Hassan, E., Wei, Y., null, H. J., & Muhuo, Y.
- Affiliations
- Donghua University (CN)
- Corresponding author
- Hassan, Elwathig
- Venue
- Journal of Fiber Bioengineering and Informatics
- Published
- 2013-06
- Volume
- 6
- Issue
- 1
- Pages
- 85-94
- ISSN
- 1940-8676 (ISSN-L)
- 2617-8699
- OpenAlex
- W2099509921
- Cited by
- 124
- References
- 36
- Citations by year
- 2026: 3 · 2025: 6 · 2024: 5 · 2023: 10 · 2022: 10 · 2021: 17 · 2020: 8 · 2019: 18 · 2018: 18 · 2017: 9 · 2016: 8 · 2015: 8 · 2014: 4
- FWCI
- 2.54
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- Journal of Fiber Bioengineering and Informatics (publishedVersion)
- Topics
- Physical Sciences › Materials Science › Biomaterials › biodegradable polymer synthesis and properties
- Physical Sciences › Materials Science › Polymers and Plastics › Polymer crystallization and properties
- Physical Sciences › Materials Science › Polymers and Plastics › Natural Fiber Reinforced Composites
- Keywords
- polylactic acid, poly(butylene succinate), polymer blends, biodegradable plastics, thermal stability, dynamic mechanical properties, impact strength, tensile strength, rheology, glass transition, molecular mobility, extrusion molding
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.