The DOI matches its Crossref record; 12 of the 12 references it cites were found in a registry or an index.
Costs and Cost Effectiveness of Additive Manufacturing
Open accessAbstract
The use of additive manufacturing has increased significantly in previous years.Additive manufacturing is used by multiple industry subsectors, including motor vehicles, aerospace, machinery, electronics, and medical products.Currently, however, additive manufactured products represent less than one percent of all manufactured products in the U.S. As the costs of additive manufacturing systems decrease, this technology may change the way that consumers interact with producers.Additive manufacturing technology opens up new opportunities for the economy and society.It can facilitate the customized production of strong light-weight products and it allows designs that were not possible with previous manufacturing techniques.Various challenges, however, can impede and slow the adoption of this technology.In many instances, the cost of producing a product using additive manufacturing processes exceeds that of traditional methods.This report examines literature on the costs of additive manufacturing and seeks to identify those instances where additive manufacturing might be cost effective and also identify potential means for reducing costs when using this technology.Current research on additive manufacturing costs reveals that this technology is cost effective for manufacturing small batches with continued centralized manufacturing; however, with increased automation distributed production may become cost effective.Due to the complexities of measuring additive manufacturing costs, current studies are limited in their scope.Many of the current studies examine the production of single parts.Those that examine assemblies tend not to examine supply chain effects such as inventory and transportation costs along with decreased risk to supply disruption.Currently, research also reveals that material costs constitute a major proportion of the cost of a product produced using additive manufacturing.However, technologies can often be complementary, where two technologies are adopted alongside each other and the benefits are greater than if they were adopted individually.Increasing adoption of additive manufacturing may lead to a reduction in raw material cost through economies of scale.The reduced cost in raw material might then propagate further adoption of additive manufacturing.There may also be economies of scale in raw material costs if particular materials become more common rather than a plethora of different materials.The additive manufacturing system is also a significant cost factor; however, this cost has continually decreased.Between 2001 and 2011 the average price decreased 51 % after adjusting for inflation.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Analysis of rapid manufacturing—using layer manufacturing processes for production
Hopkinson, N., & Dicknes, P. (2003) · Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science · doi:10.1243/095440603762554596 · Cited by 412
Environmental aspects of laser-based and conventional tool and die manufacturing
Morrow, W. R., Qi, H., Kim, I., Mazumder, J., & Skerlos, S. J. (2007) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2005.11.030 · Cited by 380
The Economics of Technological Diffusion
Stoneman, P. L. (2001) · Cited by 344
Cost estimation for rapid manufacturing - laser sintering production for low to medium volumes
Ruffo, M., Tuck, C., & Hague, R. (2006) · Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture · doi:10.1243/09544054jem517 · Cited by 342
Redesign and cost estimation of rapid manufactured plastic parts
Atzeni, E., Iuliano, L., Minetola, P., & Salmi, A. (2010) · Rapid Prototyping Journal · doi:10.1108/13552541011065704 · Cited by 205
Rapid prototyping: energy and environment in the spotlight
Mognol, P., Lepicart, D., & Perry, N. (2006) · Rapid Prototyping Journal · doi:10.1108/13552540610637246 · Cited by 185
Optimal Design for Additive Manufacturing: Opportunities and Challenges
Doubrovski, Z., Verlinden, J. C., & Geraedts, J. M. P. (2011) · Volume 9: 23rd International Conference on Design Theory and Methodology; 16th Design for Manufacturing and the Life Cycle Conference · doi:10.1115/detc2011-48131 · Cited by 166
Lindermann, C., Jahnke, U., Moi, M., & Koch, R. (2012) · doi:10.26153/tsw/15341 · Cited by 160
Telenko, C., & Seepersad, C. C. (2012) · Rapid Prototyping Journal · doi:10.1108/13552541211272018 · Cited by 107
Economic aspects of additive manufacturing : benefits, costs and energy consumption
Baumers, M. (2012) · Loughborough University Institutional Repository (Loughborough University) · Cited by 68
Cited by
Design for Additive Manufacturing: Trends, opportunities, considerations, and constraints
Thompson, M. K., Moroni, G., Vaneker, T., Fadel, G., Campbell, R. I., Gibson, I., Bernard, A., Schulz, J., Graf, P., Ahuja, B., et al. (2016) · CIRP Annals · doi:10.1016/j.cirp.2016.05.004 · Cited by 2,017
3D printing trends in building and construction industry: a review
Tay, Y. W. D., Panda, B., Paul, S. C., Noor Mohamed, N. A., Tan, M. J., & Leong, K. F. (2017) · Virtual and Physical Prototyping · doi:10.1080/17452759.2017.1326724 · Cited by 868
Metal additive manufacturing in the commercial aviation industry: A review
Gisario, A., Kazarian, M., Martina, F., & Mehrpouya, M. (2019) · Journal of Manufacturing Systems · doi:10.1016/j.jmsy.2019.08.005 · Cited by 574
Applications of additive manufacturing in the construction industry – A forward-looking review
Delgado Camacho, D., Clayton, P., O'Brien, W. J., Seepersad, C., Juenger, M., Ferron, R., & Salamone, S. (2018) · Automation in Construction · doi:10.1016/j.autcon.2017.12.031 · Cited by 538
Support Structures for Additive Manufacturing: A Review
Jiang, J., Xu, X., & Stringer, J. (2018) · Journal of Manufacturing and Materials Processing · doi:10.3390/jmmp2040064 · Cited by 527
Metadata
- Authors
- Thomas, D. S., & Gilbert, S. W.
- Published
- 2014-12
- OpenAlex
- W2715146817
- Cited by
- 443
- References
- 12
- Type
- report
- Language
- en
- Open access
- gold
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Costs and Cost Effectiveness of Additive Manufacturing. https://app.cochat.ai/papers/10.6028/nist.sp.1176
- The paper
- Thomas, D. S., & Gilbert, S. W. (2014). Costs and Cost Effectiveness of Additive Manufacturing. https://doi.org/10.6028/nist.sp.1176
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.