CoChat

Influence of racemization on stereocomplex‐induced gelation of water‐soluble polylactide–poly(ethylene glycol) block copolymers

Nouailhas, Helene, Li, Feng, El Ghzaoui, Abdelsalm, Li, Suming, Coudane, Jean · 2010 · Polymer International
Cited by 17

The DOI matches its Crossref record; 2 of the 2 references it cites were found in a registry or an index.

Abstract

Ring‐opening polymerization of L‐ or D‐lactide was realized at 140 °C for a period of 7 days in the presence of dihydroxyl poly(ethylene glycol) (PEG), with M̄n = 4000 g mol−1, using zinc lactate as initiator. The resulting poly(L‐lactide)–PEG–poly(L‐lactide) and poly(D‐lactide)–PEG–poly(D‐lactide) triblock copolymers are water soluble with polylactide (PLA) block length ranging from 11 to 17 units. Both the tube inverting method and rheological measurements were used to evaluate the gelation properties of aqueous solutions containing single copolymers or L/D copolymer pairs. Stereocomplexation between poly(L‐lactide) and poly(D‐lactide) blocks is observed for mixed solutions. Hydrogel formation is detected in the case of relatively long PLA blocks (DPPLA = 17), but not for copolymers with shorter PLA blocks (DPPLA = 11–13) due to partial racemization of L‐lactyl units. Racemization is largely reduced when the reaction time is shortened to 1 day. Under these conditions, DPPLA of 8 is sufficient for the stereocomplexation of PLA–PEG block copolymers, and DPPLA above 10 leads to the formation of hydrogels of PLA–PEG block copolymers. On the other hand, racemization appears as a general phenomenon in the (co)polymerization of L‐lactide with Zn(Lac)2 as initiator, although it is negligible or undetectable in the case of high molar mass polymers. Therefore, racemization is the limiting factor for the stereocomplexation‐induced gelation of water‐soluble PLA–PEG block copolymers where the PLA block length generally ranges from 10 to 30. Reaction conditions including initiator, time and temperature should be strictly controlled to minimize racemization. Copyright © 2010 Society of Chemical Industry

Overview

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Integrity signals

Registry

Crossref · 10.1002/pi.2831

Cites

2 of 2 references verified0 citation errors · 0 not checkable

Statistics

Verification

Claims the paper makes

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

The self-check needs the paper’s full text.

Citations

Cites

Show all 2 references

Cited by

Metadata

Authors
Nouailhas, H., Li, F., El Ghzaoui, A., Li, S., & Coudane, J.
Venue
Polymer International
Publisher
Wiley
Published
2010-07-19
Volume
59
Issue
8
Pages
1077-1083
ISSN
  • 0959-8103 (ISSN-L)
  • 1097-0126
OpenAlex
W2069795094
Cited by
17
References
2
FWCI
1.10
Type
journal article
Language
en
Open access
closed

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.