The DOI matches its Crossref record; 45 of the 45 references it cites were found in a registry or an index.
Direct ink writing of highly porous and strong glass scaffolds for load-bearing bone defects repair and regeneration
Open accessAbstract
The quest for synthetic materials to repair load-bearing bone lost because of trauma, cancer, or congenital bone defects requires development of porous and high-performance scaffolds with exceptional mechanical strength. However, the low mechanical strength of porous bioactive ceramic and glass scaffolds, compared with that of human cortical bone, has limited their use for these applications. In the present work, bioactive 6P53B glass scaffolds with superior mechanical strength were fabricated using a direct ink writing technique. The rheological properties of Pluronic® F-127 (referred to hereafter simply as F-127) hydrogel-based inkswere optimized for the printing of features as fine as 30 μm and of the three-dimensional scaffolds. The mechanical strength and in vitro degradation of the scaffolds were assessed in a simulated body fluid (SBF). The sintered glass scaffolds show a compressive strength (136 ± 22 MPa) comparable to that of human cortical bone (100-150 MPa), while the porosity (60%) is in the range of that of trabecular bone (50-90%).The strength is ~100 times that of polymer scaffolds and 4–5 times that of ceramic and glass scaffolds with comparable porosities. Despite the strength decrease resulting from weight loss during immersion in an SBF, the value (77 MPa) is still far above that of trabecular bone after three weeks. The ability to create both porous and strong structures opens a new avenue for fabricating scaffolds for load-bearing bone defect repair and regeneration.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Cellular solids structure and properties
Gibson, L. J., Ashby, M. F., et al. (1997) · Cited by 9,172
Biomechanics. Mechanical Properties of Living Tissues
Fung, Y. C., & Skalak, R. (1982) · Journal of Applied Mechanics · doi:10.1115/1.3162171 · Cited by 6,025
Cellular solids: Structure and properties
Wolcott, M. P. (1990) · Materials Science and Engineering: A · doi:10.1016/0921-5093(90)90295-e · Cited by 5,926
Porous scaffold design for tissue engineering
Hollister, S. J. (2005) · Nature Materials · doi:10.1038/nmat1421 · Cited by 3,969
Biodegradable and bioactive porous polymer/inorganic composite scaffolds for bone tissue engineering
Rezwan, K., Chen, Q. Z., Blaker, J. J., & Boccaccini, A. R. (2006) · Biomaterials · doi:10.1016/j.biomaterials.2006.01.039 · Cited by 3,839
A Mechanism for Non-Newtonian Flow in Suspensions of Rigid Spheres
Krieger, I. M., & Dougherty, T. J. (1959) · Transactions of the Society of Rheology · doi:10.1122/1.548848 · Cited by 3,402
Nature’s hierarchical materials
Fratzl, P., & Weinkamer, R. (2007) · Progress in Materials Science · doi:10.1016/j.pmatsci.2007.06.001 · Cited by 2,800
Third-Generation Biomedical Materials
Hench, L. L., & Polak, J. M. (2002) · Science · doi:10.1126/science.1067404 · Cited by 2,789
Biomechanics: Mechanical Properties of Living Tissues
Fung, Y. C., & Skalak, R. (1981) · Journal of Biomechanical Engineering · doi:10.1115/1.3138285 · Cited by 2,769
Hench, L. L. (1998) · Journal of the American Ceramic Society · doi:10.1111/j.1151-2916.1998.tb02540.x · Cited by 2,652
Cited by
Review of bioactive glass: From Hench to hybrids
Jones, J. R. (2013) · Acta Biomaterialia · doi:10.1016/j.actbio.2012.08.023 · Cited by 2,451
Bone tissue engineering using 3D printing
Bose, S., Vahabzadeh, S., & Bandyopadhyay, A. (2013) · Materials Today · doi:10.1016/j.mattod.2013.11.017 · Cited by 1,866
Direct Ink Writing: A 3D Printing Technology for Diverse Materials
Saadi, M. A. S. R., Maguire, A., Pottackal, N. T., Thakur, M. S. H., Ikram, M. M., Hart, A. J., Ajayan, P. M., & Rahman, M. M. (2022) · Advanced Materials · doi:10.1002/adma.202108855 · Cited by 1,335
Additive Manufacturing of Ceramics: Issues, Potentialities, and Opportunities
Zocca, A., Colombo, P., Gomes, C. M., & Günster, J. (2015) · Journal of the American Ceramic Society · doi:10.1111/jace.13700 · Cited by 1,115
Additive Manufacturing of Ceramic‐Based Materials
Travitzky, N., Bonet, A., Dermeik, B., Fey, T., Filbert‐Demut, I., Schlier, L., Schlordt, T., & Greil, P. (2014) · Advanced Engineering Materials · doi:10.1002/adem.201400097 · Cited by 878
Additive manufacturing of advanced ceramic materials
Lakhdar, Y., Tuck, C., Binner, J., Terry, A., & Goodridge, R. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2020.100736 · Cited by 857
Multimaterial magnetically assisted 3D printing of composite materials
Kokkinis, D., Schaffner, M., & Studart, A. R. (2015) · Nature Communications · doi:10.1038/ncomms9643 · Cited by 848
Designing Biomaterials for 3D Printing
Guvendiren, M., Molde, J., Soares, R. M. D., & Kohn, J. (2016) · ACS Biomaterials Science & Engineering · doi:10.1021/acsbiomaterials.6b00121 · Cited by 732
A review of bioactive glasses: Their structure, properties, fabrication and apatite formation
Kaur, G., Pandey, O. P., Singh, K., Homa, D., Scott, B., & Pickrell, G. (2014) · Journal of Biomedical Materials Research Part A · doi:10.1002/jbm.a.34690 · Cited by 628
Reprint of: Review of bioactive glass: From Hench to hybrids
Jones, J. R. (2015) · Acta Biomaterialia · doi:10.1016/j.actbio.2015.07.019 · Cited by 609
3D Printing of Emulsions and Foams into Hierarchical Porous Ceramics
Minas, C., Carnelli, D., Tervoort, E., & Studart, A. R. (2016) · Advanced Materials · doi:10.1002/adma.201603390 · Cited by 507
Bioinspired large-scale aligned porous materials assembled with dual temperature gradients
Bai, H., Chen, Y., Delattre, B., Tomsia, A. P., & Ritchie, R. O. (2015) · Science Advances · doi:10.1126/sciadv.1500849 · Cited by 483
Self-citationRheological characterisation of ceramic inks for 3D direct ink writing: A review
del-Mazo-Barbara, L., & Ginebra, M.-P. (2021) · Journal of the European Ceramic Society · doi:10.1016/j.jeurceramsoc.2021.08.031 · Cited by 444
3D printing of bacteria into functional complex materials
Schaffner, M., Rühs, P. A., Coulter, F., Kilcher, S., & Studart, A. R. (2017) · Science Advances · doi:10.1126/sciadv.aao6804 · Cited by 425
Bioactive Glasses: Frontiers and Challenges
Hench, L. L., & Jones, J. R. (2015) · Frontiers in Bioengineering and Biotechnology · doi:10.3389/fbioe.2015.00194 · Cited by 406
Additive manufacturing techniques for the production of tissue engineering constructs
Mota, C., Puppi, D., Chiellini, F., & Chiellini, E. (2015) · Journal of Tissue Engineering and Regenerative Medicine · doi:10.1002/term.1635 · Cited by 382
Robocasting of structural ceramic parts with hydrogel inks
Feilden, E., Blanca, E. G.-T., Giuliani, F., Saiz, E., & Vandeperre, L. (2016) · Journal of the European Ceramic Society · doi:10.1016/j.jeurceramsoc.2016.03.001 · Cited by 378
Self-citation3D Printing of Calcium Phosphate Ceramics for Bone Tissue Engineering and Drug Delivery
Trombetta, R., Inzana, J. A., Schwarz, E. M., Kates, S. L., & Awad, H. A. (2017) · Annals of Biomedical Engineering · doi:10.1007/s10439-016-1678-3 · Cited by 377
Ceramic Robocasting: Recent Achievements, Potential, and Future Developments
Peng, E., Zhang, D., & Ding, J. (2018) · Advanced Materials · doi:10.1002/adma.201802404 · Cited by 347
Bone tissue engineering scaffolding: computer-aided scaffolding techniques
Thavornyutikarn, B., Chantarapanich, N., Sitthiseripratip, K., Thouas, G. A., & Chen, Q. (2014) · Progress in Biomaterials · doi:10.1007/s40204-014-0026-7 · Cited by 325
Biomedical production of implants by additive electro-chemical and physical processes
Bartolo, P., Kruth, J.-P., Silva, J., Levy, G., Malshe, A., Rajurkar, K., Mitsuishi, M., Ciurana, J., & Leu, M. (2012) · CIRP Annals · doi:10.1016/j.cirp.2012.05.005 · Cited by 321
Bioactive Glasses: From Parent 45S5 Composition to Scaffold-Assisted Tissue-Healing Therapies
Fiume, E., Barberi, J., Verné, E., & Baino, F. (2018) · Journal of Functional Biomaterials · doi:10.3390/jfb9010024 · Cited by 313
Preethi Soundarya, S., Haritha Menon, A., Viji Chandran, S., & Selvamurugan, N. (2018) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2018.08.056 · Cited by 305
4D printing of materials for the future: Opportunities and challenges
Joshi, S., Rawat, K., C, K., Rajamohan, V., Mathew, A. T., Koziol, K., Kumar Thakur, V., & A.S.S, B. (2020) · Applied Materials Today · doi:10.1016/j.apmt.2019.100490 · Cited by 288
A review of 3D printed porous ceramics
Zhang, F., Li, Z., Xu, M., Wang, S., Li, N., & Yang, J. (2022) · Journal of the European Ceramic Society · doi:10.1016/j.jeurceramsoc.2022.02.039 · Cited by 284
Breakthrough in the printing tactics for stimuli-responsive materials: 4D printing
Rastogi, P., & Kandasubramanian, B. (2019) · Chemical Engineering Journal · doi:10.1016/j.cej.2019.02.085 · Cited by 267
3D printing of ceramic-based scaffolds for bone tissue engineering: an overview
Du, X., Fu, S., & Zhu, Y. (2018) · Journal of Materials Chemistry B · doi:10.1039/c8tb00677f · Cited by 259
Metadata
- Authors
- Fu, Q., Saiz, E., & Tomsia, A. P.
- Venue
- Acta Biomaterialia
- Publisher
- Elsevier BV
- Published
- 2011-10
- Volume
- 7
- Issue
- 10
- Pages
- 3547-3554
- ISSN
- 1742-7061 (ISSN-L)
- OpenAlex
- W2169320864
- Cited by
- 366
- References
- 45
- FWCI
- 7.11
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.