The DOI matches its Crossref record; 24 of the 24 references it cites were found in a registry or an index.
Investigation of the rheology and strength of geopolymer mixtures for extrusion-based 3D printing
Open accessAbstract
This study presents the development of fly ash-based geopolymer mixtures for 3D concrete printing. The influence of up to 10% ground granulated blast-furnace slag (GGBS) and silica fume (SF) inclusion within geopolymer blends cured under ambient conditions was investigated in terms of fresh and hardened properties. Evolution of yield stress and thixotropy of the mixtures at different resting times were evaluated. Mechanical performance of the 3D printed components was assessed via compressive strength measurements and compared with casted samples. SF demonstrated a significant influence on fresh properties (e.g. recovery of viscosity), whereas the use of GGBS led to higher early strength development within geopolymer systems. The feasibility of the 3D printing process, during which rheology was controlled, was evaluated by considering extrusion and shape retention parameters. The outcomes of this study led to the printing of a freeform 3D component, shedding light on the 3D printing of sustainable binder systems for various building components.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Mix design and fresh properties for high-performance printing concrete
Le, T. T., Austin, S. A., Lim, S., Buswell, R. A., Gibb, A. G. F., & Thorpe, T. (2012) · Materials and Structures · doi:10.1617/s11527-012-9828-z · Cited by 1,218
Rheological requirements for printable concretes
Roussel, N. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2018.04.005 · Cited by 1,203
Automated construction by contour crafting—related robotics and information technologies
Khoshnevis, B. (2004) · Automation in Construction · doi:10.1016/j.autcon.2003.08.012 · Cited by 1,161
Hardened properties of high-performance printing concrete
Le, T. T., Austin, S. A., Lim, S., Buswell, R. A., Law, R., Gibb, A. G. F., & Thorpe, T. (2012) · Cement and Concrete Research · doi:10.1016/j.cemconres.2011.12.003 · Cited by 1,020
The origins of thixotropy of fresh cement pastes
Roussel, N., Ovarlez, G., Garrault, S., et al. (2011) · Cement and Concrete Research · doi:10.1016/j.cemconres.2011.09.004 · Cited by 995
A thixotropy model for fresh fluid concretes: Theory, validation and applications
Roussel, N. (2006) · Cement and Concrete Research · doi:10.1016/j.cemconres.2006.05.025 · Cited by 967
Structural built-up of cement-based materials used for 3D-printing extrusion techniques
Perrot, A., Rangeard, D., & Pierre, A. (2016) · Materials and Structures · doi:10.1617/s11527-015-0571-0 · Cited by 959
3D printing trends in building and construction industry: a review
Tay, Y. W. D., Panda, B., Paul, S. C., Noor Mohamed, N. A., Tan, M. J., & Leong, K. F. (2017) · Virtual and Physical Prototyping · doi:10.1080/17452759.2017.1326724 · Cited by 868
Self-citationInfluence of calcium compounds on the mechanical properties of fly ash geopolymer pastes
Temuujin, J., van Riessen, A., & Williams, R. (2009) · Journal of Hazardous Materials · doi:10.1016/j.jhazmat.2008.12.121 · Cited by 834
Evolution of binder structure in sodium silicate-activated slag-metakaolin blends
Bernal, S. A., Provis, J. L., Rose, V., & Mejía de Gutierrez, R. (2011) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2010.09.004 · Cited by 786
Cited by
Daminabo, S. C., Goel, S., Grammatikos, S. A., Nezhad, H. Y., & Thakur, V. K. (2020) · Materials Today Chemistry · doi:10.1016/j.mtchem.2020.100248 · Cited by 567
Mix design concepts for 3D printable concrete: A review
Zhang, C., Nerella, V. N., Krishna, A., Wang, S., Zhang, Y., Mechtcherine, V., & Banthia, N. (2021) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2021.104155 · Cited by 421
Improving the 3D printability of high volume fly ash mixtures via the use of nano attapulgite clay
Panda, B., Ruan, S., Unluer, C., & Tan, M. J. (2019) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2018.11.109 · Cited by 405
Self-citationExtrusion-based concrete 3D printing from a material perspective: A state-of-the-art review
Mohan, M. K., Rahul, A. V., De Schutter, G., & Van Tittelboom, K. (2021) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2020.103855 · Cited by 384
Shehata, N., Mohamed, O. A., Sayed, E. T., Abdelkareem, M. A., & Olabi, A. G. (2022) · Science of The Total Environment · doi:10.1016/j.scitotenv.2022.155577 · Cited by 371
Zhao, J., Tong, L., Li, B., Chen, T., Wang, C., Yang, G., & Zheng, Y. (2021) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2021.127085 · Cited by 369
Mesh reinforcing method for 3D Concrete Printing
Marchment, T., & Sanjayan, J. (2020) · Automation in Construction · doi:10.1016/j.autcon.2019.102992 · Cited by 347
On the emergence of 3D printable Engineered, Strain Hardening Cementitious Composites (ECC/SHCC)
Li, V. C., Bos, F. P., Yu, K., McGee, W., Ng, T. Y., Figueiredo, S. C., Nefs, K., Mechtcherine, V., Nerella, V. N., Pan, J., et al. (2020) · Cement and Concrete Research · doi:10.1016/j.cemconres.2020.106038 · Cited by 342
Environmental and economic assessment on 3D printed buildings with recycled concrete
Han, Y., Yang, Z., Ding, T., & Xiao, J. (2021) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2020.123884 · Cited by 322
Sustainable materials for 3D concrete printing
Bhattacherjee, S., Basavaraj, A. S., Rahul, A. V., Santhanam, M., Gettu, R., Panda, B., Schlangen, E., Chen, Y., Copuroglu, O., Ma, G., et al. (2021) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2021.104156 · Cited by 321
Self-citationPanda, B., Lim, J. H., & Tan, M. J. (2019) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2019.02.040 · Cited by 312
Self-citationGeopolymer foams: An overview of recent advancements
Novais, R. M., Pullar, R. C., & Labrincha, J. A. (2020) · Progress in Materials Science · doi:10.1016/j.pmatsci.2019.100621 · Cited by 303
Panda, B., Noor Mohamed, N. A., Paul, S. C., Bhagath Singh, G., Tan, M. J., & Šavija, B. (2019) · Materials · doi:10.3390/ma12132149 · Cited by 301
Self-citationExtrusion and rheology characterization of geopolymer nanocomposites used in 3D printing
Panda, B., Unluer, C., & Tan, M. J. (2019) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2019.107290 · Cited by 285
Self-citation3-D printing of concrete: Beyond horizons
Khan, M. S., Sanchez, F., & Zhou, H. (2020) · Cement and Concrete Research · doi:10.1016/j.cemconres.2020.106070 · Cited by 260
Al Rashid, A., Khan, S. A., G. Al-Ghamdi, S., & Koç, M. (2020) · Automation in Construction · doi:10.1016/j.autcon.2020.103268 · Cited by 257
Synthesis and characterization of one-part geopolymers for extrusion based 3D concrete printing
Panda, B., Singh, G. B., Unluer, C., & Tan, M. J. (2019) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2019.02.185 · Cited by 254
Self-citationMa, S., Jiang, Y., Fu, S., He, P., Sun, C., Duan, X., Jia, D., Colombo, P., & Zhou, Y. (2023) · Journal of Advanced Ceramics · doi:10.26599/jac.2023.9220700 · Cited by 88
Metadata
- Authors
- Panda, B., Unluer, C., & Tan, M. J.
- Venue
- Cement and Concrete Composites
- Publisher
- Elsevier BV
- Published
- 2018-11
- Volume
- 94
- Pages
- 307-314
- ISSN
- 0958-9465 (ISSN-L)
- OpenAlex
- W2895360774
- Cited by
- 482
- References
- 24
- FWCI
- 30.32
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.