The DOI matches its Crossref record; 39 of the 39 references it cites were found in a registry or an index.
Tensile failure strength and separation angle of FDM 3D printing PLA material: Experimental and theoretical analyses
Abstract
It is discovered in this investigation that there exist two different failure modes and a special separation angle which is the demarcation point of the two different failure modes when FDM (Fused Deposition Modelling) 3D printing materials fail under a tensile load. In order to further understand the mechanical properties of FDM 3D printing materials and promote the use of FDM 3D printing materials, their tensile failure strengths at different printing angles and separation angles are measured and analysed theoretically. A new separate-modes of transversely isotropic theoretical failure model is established to predict the tensile failure strength and separation angle of FDM 3D printing PLA (polylactic acid) material based on the hypothesis of transverse isotropy and the classical separate-modes failure criterion. During this research, the tensile specimens designed according to the current test standard ISO (527-2-2012) for plastic-multi-purpose specimens are fabricated in 7 different printing angles ( 0 ∘ , 15 ∘ , 30 ∘ , 45 ∘ , 60 ∘ , 75 ∘ , 90 ∘ ) and three levels of printing layer thickness (0.1 mm, 0.2 mm, 0.3 mm). Experimental results show that the tensile failure strength increases with the increase of the printing angle or the decrease of the layer thickness. Meanwhile, inter-layer failure tends to occur when the printing angle is small and in-layer failure tends to occur when the printing angle is big. In comparison with the results predicted by the established theoretical model, all values of the Generalized-Relative-Root-Mean-Square Error are close to zero and the experimental separation angles are also between 45 ∘ and 60 ∘ . So the predictive capacity of the theoretical model is affirmed by experimental results.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Additive manufacturing (3D printing): A review of materials, methods, applications and challenges
Ngo, T. D., Kashani, A., Imbalzano, G., Nguyen, K. T. Q., & Hui, D. (2018) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2018.02.012 · Cited by 8,431
Failure Criteria for Unidirectional Fiber Composites
Hashin, Z. (1980) · Journal of Applied Mechanics · doi:10.1115/1.3153664 · Cited by 4,626
A General Theory of Strength for Anisotropic Materials
Tsai, S. W., & Wu, E. M. (1971) · Journal of Composite Materials · doi:10.1177/002199837100500106 · Cited by 3,393
3D printing of polymer matrix composites: A review and prospective
Wang, X., Jiang, M., Zhou, Z., Gou, J., & Hui, D. (2017) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2016.11.034 · Cited by 3,325
Gibson, I., Rosen, D., & Stucker, B. (2015) · doi:10.1007/978-1-4939-2113-3 · Cited by 3,299
Additive Manufacturing Technologies: Rapid Prototyping to Direct Digital Manufacturing
Gibson, I., Rosen, D. W., & Stucker, B. (2010) · National University of Singapore · doi:10.1007/978-1-4419-1120-9 · Cited by 2,969
3-D printing: The new industrial revolution
Berman, B. (2012) · Business Horizons · doi:10.1016/j.bushor.2011.11.003 · Cited by 2,481
Anisotropic material properties of fused deposition modeling ABS
Ahn, S., Montero, M., Odell, D., Roundy, S., & Wright, P. K. (2002) · Rapid Prototyping Journal · doi:10.1108/13552540210441166 · Cited by 2,382
A Fatigue Failure Criterion for Fiber Reinforced Materials
Hashin, Z., & Rotem, A. (1973) · Journal of Composite Materials · doi:10.1177/002199837300700404 · Cited by 2,000
Chacón, J. M., Caminero, M. A., García-Plaza, E., & Núñez, P. J. (2017) · Materials & Design · doi:10.1016/j.matdes.2017.03.065 · Cited by 1,603
Highly oriented carbon fiber–polymer composites via additive manufacturing
Tekinalp, H. L., Kunc, V., Velez-Garcia, G. M., Duty, C. E., Love, L. J., Naskar, A. K., Blue, C. A., & Ozcan, S. (2014) · Composites Science and Technology · doi:10.1016/j.compscitech.2014.10.009 · Cited by 1,514
Parametric appraisal of mechanical property of fused deposition modelling processed parts
Sood, A. K., Ohdar, R. K., & Mahapatra, S. S. (2010) · Materials & Design · doi:10.1016/j.matdes.2009.06.016 · Cited by 1,318
A review on additive manufacturing of polymer-fiber composites
Parandoush, P., & Lin, D. (2017) · Composite Structures · doi:10.1016/j.compstruct.2017.08.088 · Cited by 1,270
Tymrak, B. M., Kreiger, M., & Pearce, J. M. (2014) · Materials & Design · doi:10.1016/j.matdes.2014.02.038 · Cited by 1,244
3D Printing of Scaffolds for Tissue Regeneration Applications
Do, A., Khorsand, B., Geary, S. M., & Salem, A. K. (2015) · Advanced Healthcare Materials · doi:10.1002/adhm.201500168 · Cited by 949
3d printing technologies applied for food design: Status and prospects
Godoi, F. C., Prakash, S., & Bhandari, B. R. (2016) · Journal of Food Engineering · doi:10.1016/j.jfoodeng.2016.01.025 · Cited by 939
Early age mechanical behaviour of 3D printed concrete: Numerical modelling and experimental testing
Wolfs, R. J. M., Bos, F. P., & Salet, T. A. M. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2018.02.001 · Cited by 846
3D printing of functional biomaterials for tissue engineering
Zhu, W., Ma, X., Gou, M., Mei, D., Zhang, K., & Chen, S. (2016) · Current Opinion in Biotechnology · doi:10.1016/j.copbio.2016.03.014 · Cited by 822
Self-citationBlaeser, A., Duarte Campos, D. F., Puster, U., Richtering, W., Stevens, M. M., & Fischer, H. (2016) · Advanced Healthcare Materials · doi:10.1002/adhm.201500677 · Cited by 808
Ning, F., Cong, W., Hu, Y., & Wang, H. (2017) · Journal of Composite Materials · doi:10.1177/0021998316646169 · Cited by 632
Measurements of the mechanical response of unidirectional 3D-printed PLA
Song, Y., Li, Y., Song, W., Yee, K., Lee, K.-Y., & Tagarielli, V. L. (2017) · Materials & Design · doi:10.1016/j.matdes.2017.03.051 · Cited by 624
Sood, A. K., Ohdar, R. K., & Mahapatra, S. S. (2012) · Journal of Advanced Research · doi:10.1016/j.jare.2011.05.001 · Cited by 576
An Overview of 3D Printing Technologies for Food Fabrication
Sun, J., Zhou, W., Huang, D., Fuh, J. Y. H., & Hong, G. S. (2015) · Food and Bioprocess Technology · doi:10.1007/s11947-015-1528-6 · Cited by 549
Fracture Surface Analysis of 3D-Printed Tensile Specimens of Novel ABS-Based Materials
Torrado Perez, A. R., Roberson, D. A., & Wicker, R. B. (2014) · Journal of Failure Analysis and Prevention · doi:10.1007/s11668-014-9803-9 · Cited by 523
Additive manufacturing for the food industry
Lipton, J. I., Cutler, M., Nigl, F., Cohen, D., & Lipson, H. (2015) · Trends in Food Science & Technology · doi:10.1016/j.tifs.2015.02.004 · Cited by 459
Process–Structure–Properties in Polymer Additive Manufacturing via Material Extrusion: A Review
Goh, G. D., Yap, Y. L., Tan, H. K. J., Sing, S. L., Goh, G. L., & Yeong, W. Y. (2020) · Critical Reviews in Solid State and Materials Sciences · doi:10.1080/10408436.2018.1549977 · Cited by 429
Croccolo, D., De Agostinis, M., & Olmi, G. (2013) · Computational Materials Science · doi:10.1016/j.commatsci.2013.06.041 · Cited by 369
Rayegani, F., & Onwubolu, G. C. (2014) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-014-5835-2 · Cited by 358
Yao, T., Deng, Z., Zhang, K., & Li, S. (2019) · Composites Part B Engineering · doi:10.1016/j.compositesb.2019.01.025 · Cited by 352
Self-citationCaminero, M. Á., Chacón, J. M., Plaza, E. G., López, P. J. N., Reverte, J. M., & Bécar, J. P. (2019) · Polymers · doi:10.3390/polym11050799 · Cited by 319
Panda, B., Lim, J. H., & Tan, M. J. (2019) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2019.02.040 · Cited by 312
Evaluating 3D‐Printed Biomaterials as Scaffolds for Vascularized Bone Tissue Engineering
Wang, M. O., Vorwald, C. E., Dreher, M. L., Mott, E. J., Cheng, M., Cinar, A., Mehdizadeh, H., Somo, S., Dean, D., Brey, E. M., et al. (2015) · Advanced Materials · doi:10.1002/adma.201403943 · Cited by 301
3D-printed PEEK-carbon fiber (CF) composites: Structure and thermal properties
Stepashkin, А. А., Chukov, D. I., Senatov, F. S., Salimon, A. I., Korsunsky, A. M., & Kaloshkin, S. D. (2018) · Composites Science and Technology · doi:10.1016/j.compscitech.2018.05.032 · Cited by 293
Tensile strength of commercial polymer materials for fused filament fabrication 3D printing
Tanikella, N. G., Wittbrodt, B., & Pearce, J. M. (2017) · Additive Manufacturing · doi:10.1016/j.addma.2017.03.005 · Cited by 287
Influence of meso-structure and chemical composition on FDM 3D-printed parts
Alaimo, G., Marconi, S., Costato, L., & Auricchio, F. (2017) · Composites Part B Engineering · doi:10.1016/j.compositesb.2017.01.019 · Cited by 199
Ulu, E., Korkmaz, E., Yay, K., Özdoğanlar, O. B., & Kara, L. B. (2015) · Journal of Mechanical Design · doi:10.1115/1.4030998 · Cited by 132
3D bioprinting of soft materials-based regenerative vascular structures and tissues
Zhang, Z., Wang, B., Hui, D., Qiu, J., & Wang, S. (2017) · Composites Part B Engineering · doi:10.1016/j.compositesb.2017.05.011 · Cited by 99
Zhang, P., & To, A. C. (2016) · International Journal of Plasticity · doi:10.1016/j.ijplas.2015.12.012 · Cited by 82
Wang, S., Ma, Y., Deng, Z., Zhang, K., & Dai, S. (2020) · Additive manufacturing · doi:10.1016/j.addma.2020.101104 · Cited by 66
Self-citation
Cited by
Wickramasinghe, S., Do, T., & Tran, P. (2020) · Polymers · doi:10.3390/polym12071529 · Cited by 1,052
Wang, W., Zhang, B., Li, M., Li, J., Zhang, C., Han, Y., Wang, L., Wang, K., Zhou, C., Liu, L., et al. (2021) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2021.109192 · Cited by 369
Doshi, M., Mahale, A., Kumar Singh, S., & Deshmukh, S. (2022) · Materials Today: Proceedings · doi:10.1016/j.matpr.2021.10.003 · Cited by 256
Metadata
- Authors
- Yao, T., Ye, J., Deng, Z., Zhang, K., Ma, Y., & Ouyang, H.
- Venue
- Composites Part B: Engineering
- Publisher
- Elsevier BV
- Published
- 2020-05
- Volume
- 188
- Pages
- 107894
- ISSN
- 1359-8368 (ISSN-L)
- OpenAlex
- W3007145766
- Cited by
- 311
- References
- 39
- FWCI
- 16.61
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.