The DOI matches its Crossref record; 49 of the 49 references it cites were found in a registry or an index.
Clayey soil stabilization using geopolymer and Portland cement
Open accessAbstract
This study compares the mechanical performance of clayey soil stabilization using volcanic ash (VA) based geopolymer and ordinary Portland cement (OPC). The effects of curing conditions and time, alkali activator/clay and alkali activator molarity, and VA/clay ratio are determined. The compressive strength of the untreated clayey soil specimens could be increased from 0.2 to 4 MPa and 2 to 12 MPa at the OC and DC conditions, respectively, when the soil partially replaced by 15 wt% of the binders. It is observed that geopolymer treatment is more efficient at the dry conditions (DC) while the Portland cement is superb at the wet environments (OC). This difference is associated with the role of water and pH in the kinetics of geopolymerization and the Portland cement hydration. Moreover, increasing the molarity of alkali activator and alkali activator/clay improve the compressive strength of the geopolymer treated soil. Besides, the higher energy absorption in all geopolymer specimens shows the superior ductility of this material in comparison with OPC.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Mechanism of geopolymerization and factors influencing its development: a review
Khale, D., & Chaudhary, R. (2007) · Journal of Materials Science · doi:10.1007/s10853-006-0401-4 · Cited by 1,463
Alkali-Activated Cements and Concretes
Shi, C., Krivenko, P. V., & Roy, D. (2006) · Taylor & Francis eBooks · doi:10.4324/9780203390672 · Cited by 1,164
Compressive strength and microstructural characteristics of class C fly ash geopolymer
Guo, X., Shi, H., & Dick, W. A. (2010) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2009.11.003 · Cited by 820
Effect of synthesis parameters on the mechanical properties of fly ash-based geopolymers
Panias, D., Giannopoulou, I. P., & Perraki, T. (2007) · Colloids and Surfaces A: Physicochemical and Engineering Aspects · doi:10.1016/j.colsurfa.2006.12.064 · Cited by 726
Physicochemical and Engineering Behavior of Cement Treated Clays
Chew, S. H., Kamruzzaman, A. H. M., & Lee, F. H. (2004) · Journal of Geotechnical and Geoenvironmental Engineering · doi:10.1061/(asce)1090-0241(2004)130:7(696 · Cited by 623
Role of water in the synthesis of calcined kaolin-based geopolymer
ZUHUA, Z., XIAO, Y., HUAJUN, Z., & YUE, C. (2009) · Applied Clay Science · doi:10.1016/j.clay.2008.09.003 · Cited by 621
Experimental feasibility study of geopolymer as the next-generation soil stabilizer
Zhang, M., Guo, H., El-Korchi, T., Zhang, G., & Tao, M. (2013) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2013.06.017 · Cited by 560
Chindaprasirt, P., De Silva, P., Sagoe-Crentsil, K., & Hanjitsuwan, S. (2012) · Journal of Materials Science · doi:10.1007/s10853-012-6353-y · Cited by 539
Alkali-Activated Cements and Concretes
Shi, C., Roy, D. M., & Krivenko, P. V. (2003) · CRC Press eBooks · doi:10.1201/9781482266900 · Cited by 455
Stabilisation of clayey soils with high calcium fly ash and cement
Kolias, S., Kasselouri-Rigopoulou, V., & Karahalios, A. (2004) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2004.02.019 · Cited by 441
Phetchuay, C., Horpibulsuk, S., Arulrajah, A., Suksiripattanapong, C., & Udomchai, A. (2016) · Applied Clay Science · doi:10.1016/j.clay.2016.04.005 · Cited by 374
Hydration of alkali-activated ground granulated blast furnace slag
Song, S., Sohn, D., Jennings, H. M., & Mason, T. O. (2000) · Journal of Materials Science · doi:10.1023/a:1004742027117 · Cited by 363
CO2 Capture Technologies for Cement Industry
Bosoaga, A., Masek, O., & Oakey, J. E. (2009) · Energy Procedia · doi:10.1016/j.egypro.2009.01.020 · Cited by 362
Influence of soil type on stabilization with cement kiln dust
Miller, G. A., & Azad, S. (2000) · Construction and Building Materials · doi:10.1016/s0950-0618(00)00007-6 · Cited by 361
Investigation of soil stabilization using chitosan biopolymer
Hataf, N., Ghadir, P., & Ranjbar, N. (2017) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2017.09.256 · Cited by 346
Self-citationPhair, J. W., & Van Deventer, J. S. J. (2001) · Minerals Engineering · doi:10.1016/s0892-6875(01)00002-4 · Cited by 322
Ranjbar, N., Mehrali, M., Alengaram, U. J., Metselaar, H. S. C., & Jumaat, M. Z. (2014) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2014.04.064 · Cited by 321
Self-citationKriker, A., Debicki, G., Bali, A., et al. (2004) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2004.09.015 · Cited by 316
Soil strengthening using thermo-gelation biopolymers
Chang, I., Prasidhi, A. K., Im, J., & Cho, G.-C. (2015) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2014.12.116 · Cited by 309
Chindaprasirt, P., & Chalee, W. (2014) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2014.04.010 · Cited by 301
Phair, J. W., & Van Deventer, J. S. J. (2002) · International Journal of Mineral Processing · doi:10.1016/s0301-7516(02)00013-3 · Cited by 295
Ambient Temperature Drying Shrinkage and Cracking in Metakaolin‐Based Geopolymers
Kuenzel, C., Vandeperre, L. J., Donatello, S., Boccaccini, A. R., & Cheeseman, C. (2012) · Journal of the American Ceramic Society · doi:10.1111/j.1551-2916.2012.05380.x · Cited by 291
Effects of alkaline-activated fly ash and Portland cement on soft soil stabilisation
Cristelo, N., Glendinning, S., Fernandes, L., & Pinto, A. T. (2013) · Acta Geotechnica · doi:10.1007/s11440-012-0200-9 · Cited by 287
Lemougna, P. N., MacKenzie, K. J. D., & Melo, U. F. C. (2011) · Ceramics International · doi:10.1016/j.ceramint.2011.05.002 · Cited by 266
Calcium carbide residue: Alkaline activator for clay–fly ash geopolymer
Phetchuay, C., Horpibulsuk, S., Suksiripattanapong, C., Chinkulkijniwat, A., Arulrajah, A., & Disfani, M. M. (2014) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2014.07.018 · Cited by 264
Fundamental Characteristics of Cement-Admixed Clay in Deep Mixing
Lorenzo, G. A., & Bergado, D. T. (2006) · Journal of Materials in Civil Engineering · doi:10.1061/(asce)0899-1561(2006)18:2(161 · Cited by 262
Cristelo, N., Glendinning, S., Miranda, T., Oliveira, D., & Silva, R. (2012) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2012.06.037 · Cited by 234
The effect of alkali metals on the formation of geopolymeric gels from alkali-feldspars
Xu, H., & van Deventer, J. S. J. (2003) · Colloids and Surfaces A: Physicochemical and Engineering Aspects · doi:10.1016/s0927-7757(02)00499-5 · Cited by 234
Yi, Y., Gu, L., & Liu, S. (2015) · Applied Clay Science · doi:10.1016/j.clay.2014.11.005 · Cited by 232
Alkali-Activated Ground-Granulated Blast Furnace Slag for Stabilization of Marine Soft Clay
Yi, Y., Li, C., & Liu, S. (2015) · Journal of Materials in Civil Engineering · doi:10.1061/(asce)mt.1943-5533.0001100 · Cited by 189
Stabilization of clayey soil using ultrafine palm oil fuel ash (POFA) and cement
Pourakbar, S., Asadi, A., Huat, B. B. K., & Fasihnikoutalab, M. H. (2015) · Transportation Geotechnics · doi:10.1016/j.trgeo.2015.01.002 · Cited by 177
High tensile strength fly ash based geopolymer composite using copper coated micro steel fiber
Ranjbar, N., Mehrali, M., Mehrali, M., Alengaram, U. J., & Jumaat, M. Z. (2016) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2016.02.228 · Cited by 174
Self-citationStructural Performance of Alkali-Activated Soil Ash versus Soil Cement
Ríos, S., Cristelo, N., da Fonseca, A. V., & Ferreira, C. (2015) · Journal of Materials in Civil Engineering · doi:10.1061/(asce)mt.1943-5533.0001398 · Cited by 172
Investigation on Soil–Geopolymer with Slag, Fly Ash and Their Blending
Singhi, B., Laskar, A. I., & Ahmed, M. A. (2016) · Arabian Journal for Science and Engineering · doi:10.1007/s13369-015-1677-y · Cited by 159
Sargent, P., Hughes, P., Rouainia, M., & White, M. L. (2012) · Engineering Geology · doi:10.1016/j.enggeo.2012.10.013 · Cited by 154
Portland cement, composition, production and properties
Press, G. C. B. P. (1985) · Cement and Concrete Research · doi:10.1016/0008-8846(85)90136-x · Cited by 145
Du, Y., Yu, B., Liu, K., Jiang, N., & Liu, M. D. (2016) · Journal of Materials in Civil Engineering · doi:10.1061/(asce)mt.1943-5533.0001743 · Cited by 140
Ranjbar, N., Mehrali, M., Maheri, M. R., & Mehrali, M. (2017) · Cement and Concrete Research · doi:10.1016/j.cemconres.2017.05.010 · Cited by 135
Self-citationMechanical and durability properties of a soil stabilised with an alkali-activated cement
Ríos, S., Ramos, C., da Fonseca, A. V., Cruz, N., & Rodrigues, C. M. G. (2017) · European Journal of Environmental and Civil engineering · doi:10.1080/19648189.2016.1275987 · Cited by 118
Leong, H. Y., Ong, D. E. L., Sanjayan, J. G., & Nazari, A. (2018) · Journal of Materials in Civil Engineering · doi:10.1061/(asce)mt.1943-5533.0002363 · Cited by 102
Mechanical and durability properties of cement mortar with Algerian natural pozzolana
Ghrici, M., Kenai, S., & Meziane, E.-H. (2006) · Journal of Materials Science · doi:10.1007/s10853-006-0227-0 · Cited by 101
Model Study of Alkali-Activated Waste Binder for Soil Stabilization
Pourakbar, S., Huat, B. B. K., Asadi, A., & Fasihnikoutalab, M. H. (2016) · International Journal of Geosynthetics and Ground Engineering · doi:10.1007/s40891-016-0075-1 · Cited by 94
Hot-pressed geopolymer: Dual effects of heat and curing time
Ranjbar, N., Kashefi, A., & Maheri, M. R. (2017) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2017.11.004 · Cited by 83
Self-citationAlsayed, S. H., & Amjad, M. A. (1994) · Cement and Concrete Research · doi:10.1016/0008-8846(94)90124-4 · Cited by 62
Mosallanejad, A., Taghvaei, H., Azizi, S. M. M., Mohammadi, A., & Rahimpour, M. R. (2017) · Process Safety and Environmental Protection · doi:10.1016/j.cherd.2017.03.011 · Cited by 55
Mechanical Behavior and Sulfate Resistance of Alkali Activated Stabilized Clayey Soil
Singhi, B., Laskar, A. I., & Ahmed, M. A. (2017) · Geotechnical and Geological Engineering · doi:10.1007/s10706-017-0216-x · Cited by 53
Efficiency of curing on partially exposed high-strength concrete in hot climate
Bushlaibi, A. H., & Alshamsi, A. M. (2002) · Cement and Concrete Research · doi:10.1016/s0008-8846(02)00735-4 · Cited by 51
Deep dry mix ground improvement of a soft peaty clay using blast furnace slag and red gypsum
Hughes, P., & Glendinning, S. (2004) · Quarterly Journal of Engineering Geology and Hydrogeology · doi:10.1144/1470-9236/04-003 · Cited by 40
Influence of preheating of fly ash precursors to produce geopolymers
Ranjbar, N., & Kuenzel, C. (2017) · Journal of the American Ceramic Society · doi:10.1111/jace.14848 · Cited by 40
Self-citation
Cited by
A state-of-the-art review of polymers used in soil stabilization
Huang, J., Kogbara, R. B., Hariharan, N., Masad, E. A., & Little, D. N. (2021) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2021.124685 · Cited by 304
Clayey soil stabilization using alkali-activated volcanic ash and slag
Miraki, H., Shariatmadari, N., Ghadir, P., Jahandari, S., Tao, Z., & Siddique, R. (2022) · Journal of Rock Mechanics and Geotechnical Engineering · doi:10.1016/j.jrmge.2021.08.012 · Cited by 276
Self-citationKazemi, M., Faisal Kabir, S., & Fini, E. H. (2021) · Resources Conservation and Recycling · doi:10.1016/j.resconrec.2021.105776 · Cited by 221
Abdila, S. R., Abdullah, M. M. A. B., Ahmad, R., Burduhos Nergis, D. D., Rahim, S. Z. A., Omar, M. F., Sandu, A. V., Vizureanu, P., & Syafwandi (2022) · Materials · doi:10.3390/ma15010375 · Cited by 140
Ghadir, P., Zamanian, M., Mahbubi-Motlagh, N., Saberian, M., Li, J., & Ranjbar, N. (2021) · Transportation Geotechnics · doi:10.1016/j.trgeo.2021.100639 · Cited by 140
Self-citation
Metadata
- Authors
- Ghadir, P., & Ranjbar, N.
- Venue
- Construction and Building Materials
- Publisher
- Elsevier BV
- Published
- 2018-11
- Volume
- 188
- Pages
- 361-371
- ISSN
- 0950-0618 (ISSN-L)
- OpenAlex
- W2888659315
- Cited by
- 429
- References
- 49
- FWCI
- 25.37
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.