The DOI matches its Crossref record; 32 of the 32 references it cites were found in a registry or an index.
Effect of heat treatment on the phase transformation and mechanical properties of Ti6Al4V fabricated by selective laser melting
Abstract
In this work, Ti6Al4V ELI samples were fabricated with previously optimized parameters by selective laser melting (SLM) and then heat-treated under vacuum (HT) or hot isostatic pressed (HIP). Optical microscopy (OM) and scanning electron microscopy (SEM) were used to characterize the microstructure. As-built microstructure was found to be dominated by columnar grains and acicular α′ martensite. Thermo-mechanical treatments allowed to modify the microstructure in the size and shape of the grains, as well in the volume fraction and chemical composition of the phases. Apart from the phase transformation, HIP treatment also allowed to significantly reduce the interior defects, such as pores and internal cracks. Tensile and fatigue properties of the Ti6Al4V ELI samples corresponding to the different microstructures were subsequently investigated. As-built samples exhibited a high tensile strength but a poor ductility with an elongation generally smaller than 6% and low fatigue resistance. HT samples displayed a reduced tensile strength but improved elongation behavior and relatively enhanced fatigue resistance versus as-built samples. The HIP treatment also resulted in a reduction in strength but improved furthermore the ductility and the fatigue behavior due to the elimination of internal defects.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
A study of the microstructural evolution during selective laser melting of Ti–6Al–4V
Thijs, L., Verhaeghe, F., Craeghs, T., Humbeeck, J. V., & Kruth, J.-P. (2010) · Acta Materialia · doi:10.1016/j.actamat.2010.02.004 · Cited by 2,929
Materials Properties Handbook: Titanium Alloys
Boyer, R. R., Welsch, G. E., & Collings, E. W. (1994) · Medical Entomology and Zoology · Cited by 2,637
Vrancken, B., Thijs, L., Kruth, J.-P., & Van Humbeeck, J. (2012) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2012.07.022 · Cited by 1,896
Leuders, S., Thöne, M., Riemer, A., Niendorf, T., Tröster, T., Richard, H. A., & Maier, H. J. (2013) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2012.11.011 · Cited by 1,475
Influence of processing on microstructure and mechanical properties of (α+β) titanium alloys
Lütjering, G. (1998) · Materials Science and Engineering: A · doi:10.1016/s0921-5093(97)00778-8 · Cited by 1,461
Vilaro, T., Colin, C., & Bartout, J. D. (2011) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-011-0731-y · Cited by 1,283
Xu, W., Brandt, M., Sun, S., Elambasseril, J., Liu, Q., Latham, K., Xia, K., & Qian, M. (2015) · Acta Materialia · doi:10.1016/j.actamat.2014.11.028 · Cited by 1,245
Levy, G. N., Schindel, R., & Kruth, J. P. (2003) · CIRP Annals · doi:10.1016/s0007-8506(07)60206-6 · Cited by 1,121
Gu, D., Hagedorn, Y.-C., Meiners, W., Meng, G., Batista, R. J. S., Wissenbach, K., & Poprawe, R. (2012) · Acta Materialia · doi:10.1016/j.actamat.2012.04.006 · Cited by 1,089
Murr, L. E., Quinones, S. A., Gaytan, S. M., Lopez, M. I., Rodela, A., Martinez, E. Y., Hernandez, D. H., Martinez, E., Medina, F., & Wicker, R. B. (2009) · Journal of the Mechanical Behavior of Biomedical Materials · doi:10.1016/j.jmbbm.2008.05.004 · Cited by 997
Rafi, H. K., Karthik, N. V., Gong, H., Starr, T. L., & Stucker, B. E. (2013) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-013-0658-0 · Cited by 987
Selective laser melting of biocompatible metals for rapid manufacturing of medical parts
Vandenbroucke, B., & Kruth, J. (2007) · Rapid Prototyping Journal · doi:10.1108/13552540710776142 · Cited by 981
Gong, H., Rafi, K., Gu, H., Janaki Ram, G. D., Starr, T., & Stucker, B. (2015) · Materials & Design · doi:10.1016/j.matdes.2015.07.147 · Cited by 940
Fatigue performance evaluation of selective laser melted Ti–6Al–4V
Edwards, P., & Ramulu, M. (2014) · Materials Science and Engineering: A · doi:10.1016/j.msea.2014.01.041 · Cited by 874
Rapid manufacturing of metal components by laser forming
Santos, E. C., Shiomi, M., Osakada, K., & Laoui, T. (2006) · International Journal of Machine Tools and Manufacture · doi:10.1016/j.ijmachtools.2005.09.005 · Cited by 740
Improvement of fatigue resistance and ductility of TiAl6V4 processed by selective laser melting
Kasperovich, G., & Hausmann, J. (2015) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2015.01.025 · Cited by 735
Tammas-Williams, S., Zhao, H., Léonard, F., Derguti, F., Todd, I., & Prangnell, P. B. (2015) · Materials Characterization · doi:10.1016/j.matchar.2015.02.008 · Cited by 590
Ductility of a Ti‐6Al‐4V alloy produced by selective laser melting of prealloyed powders
Facchini, L., Magalini, E., Robotti, P., Molinari, A., Höges, S., & Wissenbach, K. (2010) · Rapid Prototyping Journal · doi:10.1108/13552541011083371 · Cited by 512
Microstructure and mechanical behaviour of Ti―6Al―7Nb alloy produced by selective laser melting
Chlebus, E., Kuźnicka, B., Kurzynowski, T., & Dybała, B. (2011) · Materials Characterization · doi:10.1016/j.matchar.2011.03.006 · Cited by 423
Fatigue behavior and failure mechanisms of direct laser deposited Ti–6Al–4V
Sterling, A. J., Torries, B., Shamsaei, N., Thompson, S. M., & Seely, D. W. (2015) · Materials Science and Engineering A · doi:10.1016/j.msea.2015.12.026 · Cited by 372
Fatigue behavior of porous biomaterials manufactured using selective laser melting
Amin Yavari, S., Wauthle, R., van der Stok, J., Riemslag, A. C., Janssen, M., Mulier, M., Kruth, J. P., Schrooten, J., Weinans, H., & Zadpoor, A. A. (2013) · Materials Science and Engineering: C · doi:10.1016/j.msec.2013.08.006 · Cited by 357
Rafi, H. K., Starr, T. L., & Stucker, B. E. (2013) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-013-5106-7 · Cited by 335
Improvement of fatigue life of Ti–6Al–4V alloy by laser shock peening
Zhang, X. C., Zhang, Y. K., Lu, J., Xuan, F., Wang, Z. D., & Tu, S. T. (2010) · Materials Science and Engineering A · doi:10.1016/j.msea.2010.01.076 · Cited by 319
Science in three dimensions: The print revolution
Jones, N. (2012) · Nature · doi:10.1038/487022a · Cited by 249
Benedetti, M., Torresani, E., Leoni, M., Fontanari, V., Bandini, M., Pederzolli, C., & Potrich, C. (2017) · Journal of the Mechanical Behavior of Biomedical Materials · doi:10.1016/j.jmbbm.2017.03.024 · Cited by 248
Ti-6Al-4V Additively Manufactured by Selective Laser Melting with Superior Mechanical Properties
Xu, W., Sun, S., Elambasseril, J., Liu, Q., Brandt, M., & Qian, M. (2015) · JOM · doi:10.1007/s11837-015-1297-8 · Cited by 244
Hao, L., Dadbakhsh, S., Seaman, O., & Felstead, M. (2009) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2009.06.012 · Cited by 233
High Cycle Fatigue (HCF) Performance of Ti-6Al-4V Alloy Processed by Selective Laser Melting
Wycisk, E., Emmelmann, C., Siddique, S., & Walther, F. (2013) · Advanced Materials Research · doi:10.4028/www.scientific.net/amr.816-817.134 · Cited by 215
Cunningham, R., Narra, S. P., Ozturk, T., Beuth, J., & Rollett, A. D. (2016) · JOM · doi:10.1007/s11837-015-1802-0 · Cited by 159
Fatigue limit of Ti6Al4V alloy produced by Selective Laser Sintering
Benedetti, M., Cazzolli, M., Fontanari, V., & Leoni, M. (2016) · Procedia Structural Integrity · doi:10.1016/j.prostr.2016.06.394 · Cited by 78
Crack Propagation in Additive Manufactured Materials and Structures
Riemer, A., & Richard, H. A. (2016) · Procedia Structural Integrity · doi:10.1016/j.prostr.2016.06.157 · Cited by 47
Fatigue testing of electron beam‐melted Ti‐6Al‐4V ELI alloy for dental implants
Joshi, G. V., Duan, Y., Neidigh, J. L., et al. (2012) · Journal of Biomedical Materials Research Part B Applied Biomaterials · doi:10.1002/jbm.b.32825 · Cited by 38
Cited by
Selective laser melting of Ti6Al4V alloy: Process parameters, defects and post-treatments
Singla, A. K., Banerjee, M., Sharma, A., Singh, J., Bansal, A., Gupta, M. K., Khanna, N., Shahi, A. S., & Goyal, D. K. (2021) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2021.01.009 · Cited by 383
Chen, Z., Yan, X., Yin, S., Liu, L., Liu, X., Zhao, G., Ma, W., Qi, W., Ren, Z., Liao, H., et al. (2020) · Materials Science and Engineering: C · doi:10.1016/j.msec.2019.110289 · Cited by 324
Self-citationKan, W. H., Chiu, L. N. S., Lim, C. V. S., Zhu, Y., Tian, Y., Jiang, D., & Huang, A. (2022) · Journal of Materials Science · doi:10.1007/s10853-022-06990-7 · Cited by 309
Corrosion of metallic materials fabricated by selective laser melting
Kong, D., Dong, C., Ni, X., & Li, X. (2019) · npj Materials Degradation · doi:10.1038/s41529-019-0086-1 · Cited by 259
Post-Process Treatments for Additive-Manufactured Metallic Structures: A Comprehensive Review
Ge, J., Pillay, S., & Ning, H. (2023) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-023-08051-9 · Cited by 157
Metadata
- Authors
- Yan, X., Yin, S., Chen, C., Huang, C., Bolot, R., Lupoi, R., Kuang, M., Ma, W., Coddet, C., Liao, H., & Liu, M.
- Venue
- Journal of Alloys and Compounds
- Publisher
- Elsevier BV
- Published
- 2018-10
- Volume
- 764
- Pages
- 1056-1071
- ISSN
- 0925-8388 (ISSN-L)
- OpenAlex
- W2809577129
- Cited by
- 326
- References
- 32
- FWCI
- 18.23
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.