The DOI matches its Crossref record; 7 of the 7 references it cites were found in a registry or an index.
Semi-crystalline feedstock for filament-based 3D printing of polymers
Open accessAbstract
Additive Manufacturing (AM), and more specifically Fused Filament Fabrication (FFF), allow the production of highly customized parts, provide enormous freedom-of-design and can lead to material savings due to the layer-by-layer material deposition that is inherent to this family of production processes. FFF utilizes both amorphous and semi-crystalline thermoplastic filaments as feedstock materials, offering a wider range of materials compared to some other polymer-based additive manufacturing techniques. However, the current trend where FFF, and AM in general, are changing from a technique for rapid prototyping to the production of fully functional parts designed for high-end applications creates the inevitable need to incorporate more engineering and high-performance thermoplastics, which are most often semi-crystalline polymers, into the material palette. Crystallization provides semi-crystalline polymers with some distinct features that set them apart from their amorphous counterparts, yet it also can present difficulties regarding their processing. Understanding of the behavior of semicrystalline polymers during FFF processing is thus a prerequisite to exploit their full potential. This review provides a broad overview of FFF processing of semicrystalline polymers. Particular focus lies on the impact of processing conditions and feedstock modifications, such as the incorporation of fillers or the formation of blends, on crystallinity as well as the microstructure of printed parts, the impact of microstructure on the mechanical performance, and general part quality. Furthermore, attention is given to some specific phenomena that can occur during printing of semi-crystalline feedstock filaments which have shown to strongly impact the printing process. Examples are self-nucleation in the case of insufficient heat transfer and melting, flow-induced crystallization due to high shear deformations upon extrusion, and the negative impact of crystallization on chain mobility which is relevant for the development of interlayer strength and on dimensional accuracy due to excessive shrinkage. Finally, this review is concluded with a critical outlook on perspectives for future research to address the current challenges that are still faced when employing semi-crystalline polymers as FFF feedstock.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Additive manufacturing (3D printing): A review of materials, methods, applications and challenges
Ngo, T. D., Kashani, A., Imbalzano, G., Nguyen, K. T. Q., & Hui, D. (2018) · Composites Part B: Engineering · doi:10.1016/j.compositesb.2018.02.012 · Cited by 8,431
Properties and medical applications of polylactic acid: A review
Hamad, K., Kaseem, M., Yang, H. W., Deri, F., & Ko, Y. G. (2015) · Express Polymer Letters · doi:10.3144/expresspolymlett.2015.42 · Cited by 722
Yang, C., Tian, X., Li, D., Cao, Y., Zhao, F., & Shi, C. (2017) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2017.04.027 · Cited by 662
Liu, Z., Wang, Y., Wu, B., Cui, C., Guo, Y., & Yan, C. (2019) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-019-03332-x · Cited by 469
Additive layer manufacturing of poly (ether ether ketone) via FDM
Rinaldi, M., Ghidini, T., Cecchini, F., Brandao, A., & Nanni, F. (2018) · Composites Part B Engineering · doi:10.1016/j.compositesb.2018.03.029 · Cited by 301
Performance of biocompatible PEEK processed by fused deposition additive manufacturing
Arif, M. F., Kumar, S., Varadarajan, K. M., & Cantwell, W. J. (2018) · Materials & Design · doi:10.1016/j.matdes.2018.03.015 · Cited by 296
Gonzalez Ausejo, J., Rydz, J., Musioł, M., Sikorska, W., Sobota, M., Włodarczyk, J., Adamus, G., Janeczek, H., Kwiecień, I., Hercog, A., et al. (2018) · Polymer Degradation and Stability · doi:10.1016/j.polymdegradstab.2018.04.024 · Cited by 117
Cited by
A review on voids of 3D printed parts by fused filament fabrication
Tao, Y., Kong, F., Li, Z., Zhang, J., Zhao, X., Yin, Q., Xing, D., & Li, P. (2021) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2021.10.108 · Cited by 443
Kassab, A., Al Nabhani, D., Mohanty, P., Pannier, C., & Ayoub, G. Y. (2023) · Polymers · doi:10.3390/polym15193881 · Cited by 141
“Consequently, our focus will be on investigating these mechanisms, aiming to enhance our comprehension of the potential degradation processes that could occur in recycled 3D printed components [239].”
BackgroundRashed, K., Kafi, A., Simons, R., & Bateman, S. (2023) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-023-11167-w · Cited by 38
“For samples printed on edge, the nozzle had to travel a longer distance before printing over the same point, causing polymer in the bottom layer to cool down, and thus, samples printed on edge may have weaker interlayer bonding when compared to flat printed samples [75].”
BackgroundMolinari, G., Aliotta, L., Gigante, V., Gemmi, M., & Lazzeri, A. (2026) · Polymer International · doi:10.1002/pi.70187
Metadata
- Authors
- Vaes, D., & Van Puyvelde, P.
- Venue
- Progress in Polymer Science
- Publisher
- Elsevier BV
- Published
- 2021-07
- Volume
- 118
- Pages
- 101411
- ISSN
- 0079-6700 (ISSN-L)
- OpenAlex
- W3157696973
- Cited by
- 231
- References
- 7
- FWCI
- 11.70
- Type
- journal article
- Language
- en
- Open access
- hybrid
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Semi-crystalline feedstock for filament-based 3D printing of polymers. https://app.cochat.ai/papers/10.1016/j.progpolymsci.2021.101411
- The paper
- Vaes, D., & Van Puyvelde, P. (2021). Semi-crystalline feedstock for filament-based 3D printing of polymers. Progress in Polymer Science. https://doi.org/10.1016/j.progpolymsci.2021.101411
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.