Microchannel cooling of concentrator photovoltaics: A review
The DOI matches its Crossref record; 71 of the 71 references it cites were found in a registry or an index.
Abstract
The intensifying heat flux demands of concentrator photovoltaics requires innovation beyond conventional passive air cooling. Passive cooling is cost effective, reliable and does not consume power. Flat lens arrangements should allow large passive heat sinks to cool at solar concentrations of up to 2000 suns to 4000 suns (1 sun = 1000 W/m2). However, as solar concentrations increase so will the necessity of active cooling. The competitiveness of active cooling is enhanced by the capacity to harvest otherwise wasted thermal energy. Pairing with phase change materials presents an opportunity to stabilise the intermittent generation of solar thermal energy. Active microchannel cooling is a strong candidate for meeting the escalating heat flux demands of concentrator photovoltaics. For meeting short term-heat flux demands, established single phase microchannel cooling is most practical. Manifold microchannels yield superior performance to single layered microchannels, although they are more difficult to manufacture. For meeting long term heat flux demands, integration of boiling flows is promising. Jet impingement onto porous microstructures demonstrates effective mitigation of flow instabilities. Future studies should apply microchannel cooling directly to concentrator photovoltaics, particularly two-phase systems. They should also test microchannel cooling over larger heater areas and consider manufacturability of heat sinks. Novel directions should also be explored, such as alteration of typically rectangular and straight manifold microchannels or use of micro-valves to suppress boiling instabilities. Incipient cooling methods, including vortex shedding, ionic jet impingement, slug flow and shear driven gas flow, may also warrant further investigations.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
The contribution of outdoor air pollution sources to premature mortality on a global scale
Lelieveld, J., Evans, J. S., Fnais, M., Giannadaki, D., & Pozzer, A. (2015) · Nature · doi:10.1038/nature15371 · Cited by 5,977
Review on thermal energy storage with phase change materials and applications
Sharma, A., Tyagi, V. V., Chen, C. R., & Buddhi, D. (2009) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2007.10.005 · Cited by 5,936
High-performance heat sinking for VLSI
Tuckerman, D. B., & Pease, R. F. W. (1981) · IEEE Electron Device Letters · doi:10.1109/edl.1981.25367 · Cited by 5,291
40% efficient metamorphic GaInP∕GaInAs∕Ge multijunction solar cells
King, R. R., Law, D. C., Edmondson, K. M., Fetzer, C. M., Kinsey, G. S., Yoon, H., Sherif, R. A., & Karam, N. H. (2007) · Applied Physics Letters · doi:10.1063/1.2734507 · Cited by 1,238
Ambient Air Pollution Exposure Estimation for the Global Burden of Disease 2013
Brauer, M., Freedman, G., Frostad, J., van Donkelaar, A., Martin, R. V., Dentener, F., Dingenen, R. V., Estep, K., Amini, H., Apte, J. S., et al. (2016) · Environmental Science & Technology · doi:10.1021/acs.est.5b03709 · Cited by 1,215
International Renewable Energy Agency
(2021) · Permanent Missions to the United Nations · doi:10.18356/9789210056755c212 · Cited by 1,052
A critical review of traditional and emerging techniques and fluids for electronics cooling
Sohel Murshed, S. M., & Nieto de Castro, C. A. (2017) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2017.04.112 · Cited by 987
Evolution of Microchannel Flow Passages--Thermohydraulic Performance and Fabrication Technology
Kandlikar, S. G., & Grande, W. J. (2003) · Heat Transfer Engineering · doi:10.1080/01457630304040 · Cited by 960
Cooling of photovoltaic cells under concentrated illumination: a critical review
ROYNE, A., DEY, C., & MILLS, D. (2005) · Solar Energy Materials and Solar Cells · doi:10.1016/j.solmat.2004.09.003 · Cited by 760
Flow boiling in microchannels: Fundamentals and applications
Karayiannis, T. G., & Mahmoud, M. M. (2016) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2016.08.063 · Cited by 620
Fluid flow and heat transfer in wavy microchannels
Sui, Y., Teo, C. J., Lee, P. S., Chew, Y. T., & Shu, C. (2010) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2010.02.022 · Cited by 595
Water spray cooling technique applied on a photovoltaic panel: The performance response
Nižetić, S., Čoko, D., Yadav, A., & Grubišić-Čabo, F. (2016) · Energy Conversion and Management · doi:10.1016/j.enconman.2015.10.079 · Cited by 553
Increased electrical yield via water flow over the front of photovoltaic panels
Krauter, S. (2004) · Solar Energy Materials and Solar Cells · doi:10.1016/j.solmat.2004.01.011 · Cited by 545
Zhang, X., Zhao, X., Smith, S. T., Xu, J., & Yu, X. (2011) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2011.08.026 · Cited by 532
Zhao, C. Y., & Zhang, G. H. (2011) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2011.07.019 · Cited by 482
Delgado, M., Lázaro, A., Mazo, J., & Zalba, B. (2012) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2011.07.152 · Cited by 430
Ma, T., Yang, H., Zhang, Y., Lu, L., & Wang, X. (2015) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2014.12.003 · Cited by 419
Abdolzadeh, M., & Ameri, M. (2008) · Renewable Energy · doi:10.1016/j.renene.2008.03.024 · Cited by 373
Uniform cooling of photovoltaic panels: A review
Bahaidarah, H. M. S., Baloch, A. A. B., & Gandhidasan, P. (2016) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2015.12.064 · Cited by 361
Two-Phase Microchannel Heat Sinks: Theory, Applications, and Limitations
Mudawar, I. (2011) · Journal of Electronic Packaging · doi:10.1115/1.4005300 · Cited by 347
Lewis, N. S., Crabtree, G., Nozik, A. J., Wasielewski, M. R., Alivisatos, P., Kung, H., Tsao, J., Chandler, E., Walukiewicz, W., Spitler, M., et al. (2005) · doi:10.2172/899136 · Cited by 335
Improving Photovoltaic Module Efficiency Using Water Cooling
Odeh, S., & Behnia, M. (2009) · Heat Transfer Engineering · doi:10.1080/01457630802529214 · Cited by 334
Cooling methodologies of photovoltaic module for enhancing electrical efficiency: A review
Shukla, A., Kant, K., Sharma, A., & Biwolé, P. H. (2016) · Solar Energy Materials and Solar Cells · doi:10.1016/j.solmat.2016.10.047 · Cited by 334
Progress of nanofluid application in solar collectors: A review
Verma, S. K., & Tiwari, A. K. (2015) · Energy Conversion and Management · doi:10.1016/j.enconman.2015.04.071 · Cited by 329
Thermodynamic and transport properties of fluids
Rogers, G. F. C., & Mayhew, Y. (1967) · Cited by 307
Optics for concentrating photovoltaics: Trends, limits and opportunities for materials and design
Shanks, K., Senthilarasu, S., & Mallick, T. K. (2016) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2016.01.089 · Cited by 307
Phase change materials for photovoltaic thermal management
Browne, M. C., Norton, B., & McCormack, S. J. (2015) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2015.03.050 · Cited by 303
Chandel, S. S., & Agarwal, T. (2017) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2017.02.001 · Cited by 299
Heat Transfer in Microchannels—2012 Status and Research Needs
Kandlikar, S. G., Colin, S., Peles, Y., Garimella, S., Pease, R. F., Brandner, J. J., & Tuckerman, D. B. (2013) · Journal of Heat Transfer · doi:10.1115/1.4024354 · Cited by 285
Thermal management systems for Photovoltaics (PV) installations: A critical review
Du, D., Darkwa, J., & Kokogiannakis, G. (2013) · Solar Energy · doi:10.1016/j.solener.2013.08.018 · Cited by 272
A Practical Implementation of Silicon Microchannel Coolers for High Power Chips
Colgan, E. G., Furman, B., Gaynes, M., Graham, W. S., LaBianca, N. C., Magerlein, J. H., Polastre, R. J., Rothwell, M. B., Bezama, R. J., Choudhary, R., et al. (2007) · IEEE Transactions on Components and Packaging Technologies · doi:10.1109/tcapt.2007.897977 · Cited by 252
Global analysis of photovoltaic energy output enhanced by phase change material cooling
Smith, C., Forster, P. M. D. F., & Crook, R. (2014) · Applied Energy · doi:10.1016/j.apenergy.2014.03.083 · Cited by 250
Sharaf, O. Z., & Orhan, M. F. (2015) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2015.05.036 · Cited by 247
Cui, T., Xuan, Y., & Li, Q. (2016) · Energy Conversion and Management · doi:10.1016/j.enconman.2016.01.008 · Cited by 245
Current Status of Concentrator Photovoltaic (CPV) Technology
National Renewable Energy Lab. (NREL), G., Philipps, S. P., Solar Energy Technologies Office (EE-4S) USDOE Office of Energy Efficiency and Renewable Energy (EERE), Bett, A., Horowitz, K. A. W., & Kurtz, S. (2015) · doi:10.2172/1351597 · Cited by 243
Smakulski, P., & Pietrowicz, S. (2016) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2016.05.096 · Cited by 230
Experimental Investigation of an Ultrathin Manifold Microchannel Heat Sink for Liquid-Cooled Chips
Escher, W., Brunschwiler, T., Michel, B., & Poulikakos, D. (2010) · Journal of Heat Transfer · doi:10.1115/1.4001306 · Cited by 211
Sui, Y., Teo, C. J., & Lee, P. S. (2012) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2011.08.041 · Cited by 203
Salman, B. H., Mohammed, H. A., Munisamy, K. M., & Kherbeet, A. S. (2013) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2013.08.012 · Cited by 203
Islam, M. M., Pandey, A. K., Hasanuzzaman, M., & Rahim, N. A. (2016) · Energy Conversion and Management · doi:10.1016/j.enconman.2016.07.075 · Cited by 198
Fluid flow and heat transfer in microchannel heat sink based on porous fin design concept
Chuan, L., Wang, X.-D., Wang, T.-H., & Yan, W.-M. (2015) · International Communications in Heat and Mass Transfer · doi:10.1016/j.icheatmasstransfer.2015.04.005 · Cited by 196
Numerical optimization of the thermal performance of a microchannel heat sink
Ryu, J. H., Choi, D. H., & Kim, S. J. (2002) · International Journal of Heat and Mass Transfer · doi:10.1016/s0017-9310(02)00006-6 · Cited by 188
Bahaidarah, H. M. S. (2016) · Solar Energy · doi:10.1016/j.solener.2016.06.015 · Cited by 181
Fabrication of microchannels: A review
Prakash, S., & Kumar, S. (2015) · Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture · doi:10.1177/0954405414535581 · Cited by 176
Wang, G., Niu, D., Xie, F., Wang, Y., Zhao, X., & Ding, G. (2015) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2015.04.009 · Cited by 171
Zhong, Y., Li, S., Wei, X., Liu, Z., Guo, Q., Shi, J., & Liu, L. (2010) · Carbon · doi:10.1016/j.carbon.2009.09.033 · Cited by 170
Liao, T., Lin, B., & Yang, Z. (2013) · International Journal of Thermal Sciences · doi:10.1016/j.ijthermalsci.2013.10.013 · Cited by 163
Alfaryjat, A. A., Mohammed, H. A., Adam, N. M., Ariffin, M. K. A., & Najafabadi, M. I. (2014) · International Communications in Heat and Mass Transfer · doi:10.1016/j.icheatmasstransfer.2014.01.015 · Cited by 160
Analysis of temperature coefficients for III–V multi‐junction concentrator cells
Siefer, G., & Bett, A. W. (2012) · Progress in Photovoltaics Research and Applications · doi:10.1002/pip.2285 · Cited by 158
A novel high performance, ultra thin heat sink for electronics
Escher, W., Michel, B., & Dimos Poulikakos, A. (2010) · International Journal of Heat and Fluid Flow · doi:10.1016/j.ijheatfluidflow.2010.03.001 · Cited by 156
Enhancing heat transfer in microchannel heat sinks using converging flow passages
Dehghan, M., Daneshipour, M., Valipour, M. S., Rafee, R., & Seyfolah Saedodin, A. (2015) · Energy Conversion and Management · doi:10.1016/j.enconman.2014.12.063 · Cited by 152
Micheli, L., Sarmah, N., Luo, X., Reddy, K. S., & Mallick, T. K. (2013) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2012.11.051 · Cited by 149
Cui, T., Xuan, Y., Yin, E., Li, Q., & Li, D. (2017) · Energy · doi:10.1016/j.energy.2017.01.087 · Cited by 148
Xiao, X., Zhang, P., & Li, M. (2013) · Energy Conversion and Management · doi:10.1016/j.enconman.2013.04.007 · Cited by 143
Optimization and Design of a Multipass Branching Microchannel Heat Sink for Electronics Cooling
Dede, E. M. (2012) · Journal of Electronic Packaging · doi:10.1115/1.4007159 · Cited by 142
Siddiqui, O. K., & Zubair, S. M. (2017) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2017.01.074 · Cited by 127
Mohsenzadeh, M., Shafii, M. B., & Mosleh, H. J. (2017) · Renewable Energy · doi:10.1016/j.renene.2017.06.047 · Cited by 119
Da, Y., Xuan, Y., & Li, Q. (2015) · Energy · doi:10.1016/j.energy.2015.12.024 · Cited by 115
A comparative analysis of innovative microchannel heat sinks for electronic cooling
Lu, S., & Vafai, K. (2016) · International Communications in Heat and Mass Transfer · doi:10.1016/j.icheatmasstransfer.2016.04.024 · Cited by 112
Ho, C. J., Chou, W.-L., & Lai, C.-M. (2014) · Energy Conversion and Management · doi:10.1016/j.enconman.2014.10.039 · Cited by 111
Kermani, E., Dessiatoun, S. V., Shooshtari, A. H., & Ohadi, M. M. (2009) · IEEE Electronic Components and Technology Conference (ECTC) · doi:10.1109/ectc.2009.5074053 · Cited by 92
Riera, S., Barrau, J., Omri, M., Fréchette, L. G., & Rosell, J. I. (2014) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2014.12.012 · Cited by 72
A high-efficiency hybrid high-concentration photovoltaic system
Zimmermann, S., Helmers, H., Tiwari, M. K., Paredes, S., Michel, B., Wiesenfarth, M., Bett, A. W., & Dimos Poulikakos, A. (2015) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2015.04.068 · Cited by 70
Gaillard, L., Giroux–Julien, S., Ménézo, C., & Pabiou, H. (2014) · Solar Energy · doi:10.1016/j.solener.2014.02.018 · Cited by 62
Dependence of multi-junction solar cells parameters on concentration and temperature
Or, A. B., & Appelbaum, J. (2014) · Solar Energy Materials and Solar Cells · doi:10.1016/j.solmat.2014.07.010 · Cited by 61
Thermal charging study of compressed expanded natural graphite/phase change material composites
Mallow, A., Abdelaziz, O. A., & Graham, S. L. (2016) · Carbon · doi:10.1016/j.carbon.2016.08.030 · Cited by 59
Tran, N., Chang, Y., Teng, J., & Greif, R. (2016) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2016.09.076 · Cited by 56
Zhang, G. C., Jiang, S., Yao, W. F., & Liu, C. (2016) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.6b08815 · Cited by 45
Kang, X., Wang, Y., Huang, Q., Cui, Y., Shi, X., & Sun, Y. (2016) · Energy Conversion and Management · doi:10.1016/j.enconman.2016.09.073 · Cited by 33
Si-Based Hybrid Microcooler With Multiple Drainage Microtrenches for High Heat Flux Cooling
Han, Y., Lau, B. L., Tang, G., Zhang, X., & Rhee, D. M. W. (2016) · IEEE Transactions on Components Packaging and Manufacturing Technology · doi:10.1109/tcpmt.2016.2627040 · Cited by 32
Yoon, H., Nabar, S., & Banin, Y. (2013) · MRS Proceedings · doi:10.1557/opl.2013.231 · Cited by 2
Metadata
- Authors
- Gilmore, N., Timchenko, V., & Menictas, C.
- Venue
- Renewable and Sustainable Energy Reviews
- Publisher
- Elsevier BV
- Published
- 2018-07
- Volume
- 90
- Pages
- 1041-1059
- ISSN
- 1364-0321 (ISSN-L)
- OpenAlex
- W2800956249
- Cited by
- 170
- References
- 71
- FWCI
- 9.91
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.