CoChat

Improved Bone Regeneration in Rabbit Bone Defects Using 3D Printed Composite Scaffolds Functionalized with Osteoinductive Factors

Open access
Teotia, Arun Kumar, Dienel, Kasper, Qayoom, Irfan, van Bochove, Bas, Gupta, Sneha, Partanen, Jouni, Seppälä, Jukka, Kumar, Ashok · 2020 · ACS Applied Materials & Interfaces

The DOI matches its Crossref record; 61 of the 62 references it cites were found in a registry or an index.

Abstract

The scaffolds were functionalized with osteoactive factors: bone morphogenetic protein and zoledronic acid. It was observed that the bioactive molecule-functionalized 3D printed porous composite scaffolds provide an excellent conductive surface inducing higher bone formation and improved defect healing in both critical size long bones and cranial defects.

Overview

CoChat Summary

TL;DR

The paper reports 3D printed poly(trimethylene carbonate)-based composite scaffolds, filled with a macroporous cryogel and functionalized with bone morphogenetic protein and zoledronic acid, as synthetic bone grafts. In two rabbit defect models, these functionalized scaffolds showed higher bone formation and improved defect healing than the baseline described in the paper.

Key findings

  • The authors produced photocuring composite resins with poly(trimethylene carbonate) containing high ratios of bioactive ceramics and printed porous 3D composite scaffolds for bone grafting.
  • The scaffolds were further filled with a macroporous cryogel to increase surface area for cell infiltration and functionalized with osteoactive factors: bone morphogenetic protein and zoledronic acid.
  • In vitro, the scaffolds were evaluated for biocompatibility; in vivo they were tested in critical bone defects of approximately 8 mm in two rabbit models: a smaller rabbit tibia study and a larger rabbit cranium study.
  • The paper states that the bioactive molecule-functionalized 3D printed porous composite scaffolds induced higher bone formation and improved defect healing in both critical-size long-bone and cranial defects.

Methods

  • Design: Experimental biomaterials study with in vitro biocompatibility testing and in vivo rabbit implantation in two clinically relevant critical-defect models.
  • Data/sample: Rabbit tibia model and rabbit cranium model, each with critical bone defects of about 8 mm.
  • Main analysis: Comparison of bone regeneration and defect healing after implantation of 3D printed porous composite scaffolds, including scaffolds functionalized with bone morphogenetic protein and zoledronic acid.

Limitations

  • The paper does not state the sample size, group allocation, follow-up duration, or quantitative effect sizes in the provided text.
  • The provided text does not report detailed statistical results or specific numerical outcomes beyond the approximate defect size (~8 mm); this is evident from the text.
  • Only rabbit models are described, so generalization to other species or human clinical outcomes is not established in the provided text.

Model-written summary. Check it against the paper before relying on it.

Integrity signals

Registry

Crossref · 10.1021/acsami.0c13851

Cites

61 of 61 references verified0 citation errors · 0 not checkable

Statistics

Nothing to recompute.

Verification

Claims the paper makes

0 Valid · 0 Not valid · 0 Not checked · 4 Own results and interpretations

Show all 4 claims

Citations

Cites

Show all 61 references

Research works printed but not linked: 2

  1. Key J., 1934, J. Bone Jt. Surg., 16, 176
  2. Bartee B. K., 1995, J. Oral Implantol., 21, 88

Cited by

Metadata

Authors
Teotia, A. K., Dienel, K., Qayoom, I., van Bochove, B., Gupta, S., Partanen, J., Seppälä, J., & Kumar, A.
Affiliations
  • Indian Institute of Technology Kanpur (IN)
  • Aalto University (FI)
  • Polymer Technology, School of Chemical Engineering, Aalto University, Espoo 02150, Finland
Corresponding author
Kumar, Ashok
Venue
ACS Applied Materials & Interfaces
Published
2020-09-30
Volume
12
Issue
43
Pages
48340-48356
ISSN
  • 1944-8244 (ISSN-L)
  • 1944-8252
OpenAlex
W3091599066
Cited by
53
References
62
Citations by year
2026: 2 · 2025: 16 · 2024: 13 · 2023: 10 · 2022: 9 · 2021: 3
FWCI
1.73
Type
journal article
Language
en
Open access
Locations
  • ACS Applied Materials & Interfaces (publishedVersion)
  • PubMed (publishedVersion)
  • Aaltodoc (Aalto University) (submittedVersion, other-oa)
Funders
  • Indian Institute of Technology Kanpur
  • Science and Engineering Research Board (IPA/2020/000026)
  • Department of Biotechnology , Ministry of Science and Technology (BT/IN/Sweden/08/AK/2017-18)
  • Department of Science and Technology, Ministry of Science and Technology (DST/NM/NT-2018/48)
  • Ministry of Human Resource Development (MHRD_IITK_006, SPARC/2018?2019/P612/SL)
Topics
  • Physical Sciences › Engineering › Biomedical Engineering › Bone Tissue Engineering Materials
  • Physical Sciences › Engineering › Biomedical Engineering › 3D Printing in Biomedical Research
  • Physical Sciences › Engineering › Biomedical Engineering › Anatomy and Medical Technology
Keywords
bone regeneration, critical-size bone defect, 3D-printed scaffolds, composite resin, poly(trimethylene carbonate), bioactive ceramics, photocuring, cryogels, bone morphogenetic proteins, zoledronic acid, synthetic bone substitutes, rabbit tibia, porous scaffolds, biocompatibility
MeSH terms
Animals, Biocompatible Materials, Bone Regeneration, Male, Osteogenesis, Particle Size, Rabbits, Surface Properties, Porosity, Bone Substitutes, Tissue Scaffolds, Printing, Three-Dimensional

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

A language model drew the claims from the paper on 2026-10-11, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).

A second model labelled each claim on 2026-10-11 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.