Improved Bone Regeneration in Rabbit Bone Defects Using 3D Printed Composite Scaffolds Functionalized with Osteoinductive Factors
Open accessThe DOI matches its Crossref record; 61 of the 62 references it cites were found in a registry or an index.
Abstract
The scaffolds were functionalized with osteoactive factors: bone morphogenetic protein and zoledronic acid. It was observed that the bioactive molecule-functionalized 3D printed porous composite scaffolds provide an excellent conductive surface inducing higher bone formation and improved defect healing in both critical size long bones and cranial defects.
Overview
CoChat Summary
TL;DR
The paper reports 3D printed poly(trimethylene carbonate)-based composite scaffolds, filled with a macroporous cryogel and functionalized with bone morphogenetic protein and zoledronic acid, as synthetic bone grafts. In two rabbit defect models, these functionalized scaffolds showed higher bone formation and improved defect healing than the baseline described in the paper.
Key findings
- The authors produced photocuring composite resins with poly(trimethylene carbonate) containing high ratios of bioactive ceramics and printed porous 3D composite scaffolds for bone grafting.
- The scaffolds were further filled with a macroporous cryogel to increase surface area for cell infiltration and functionalized with osteoactive factors: bone morphogenetic protein and zoledronic acid.
- In vitro, the scaffolds were evaluated for biocompatibility; in vivo they were tested in critical bone defects of approximately 8 mm in two rabbit models: a smaller rabbit tibia study and a larger rabbit cranium study.
- The paper states that the bioactive molecule-functionalized 3D printed porous composite scaffolds induced higher bone formation and improved defect healing in both critical-size long-bone and cranial defects.
Methods
- Design: Experimental biomaterials study with in vitro biocompatibility testing and in vivo rabbit implantation in two clinically relevant critical-defect models.
- Data/sample: Rabbit tibia model and rabbit cranium model, each with critical bone defects of about 8 mm.
- Main analysis: Comparison of bone regeneration and defect healing after implantation of 3D printed porous composite scaffolds, including scaffolds functionalized with bone morphogenetic protein and zoledronic acid.
Limitations
- The paper does not state the sample size, group allocation, follow-up duration, or quantitative effect sizes in the provided text.
- The provided text does not report detailed statistical results or specific numerical outcomes beyond the approximate defect size (~8 mm); this is evident from the text.
- Only rabbit models are described, so generalization to other species or human clinical outcomes is not established in the provided text.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
0 Valid · 0 Not valid · 0 Not checked · 4 Own results and interpretations
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“It was observed that the bioactive molecule-functionalized 3D printed porous composite scaffolds provide an excellent conductive surface inducing higher bone formation and improved defect healing in both critical size long bones and cranial defects.”
- Also stated in: § Title · plain
“Improved Bone Regeneration in Rabbit Bone Defects Using 3D Printed Composite Scaffolds Functionalized with Osteoinductive Factors”
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Also stated in: § Title · plain
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“It was observed that the bioactive molecule-functionalized 3D printed porous composite scaffolds provide an excellent conductive surface inducing higher bone formation and improved defect healing in both critical size long bones and cranial defects.”
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A conclusion the paper draws from its own results — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Our findings provide strong evidence in favor of these composites as next generation synthetic bone substitutes.”
boostedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A conclusion the paper draws from its own results — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“It was observed that the bioactive molecule-functionalized 3D printed porous composite scaffolds provide an excellent conductive surface inducing higher bone formation and improved defect healing in both critical size long bones and cranial defects.”
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
Citations
Cites
Matrix elasticity directs stem cell lineage specification
Engler, A. J., Sen, S., Sweeney, H. L., & Discher, D. E. (2006) · Cell · doi:10.1016/j.cell.2006.06.044 · Cited by 13,915
Fracture healing: mechanisms and interventions
Einhorn, T. A., & Gerstenfeld, L. C. (2015) · Nature Reviews Rheumatology · doi:10.1038/nrrheum.2014.164 · Cited by 1,807
Tsuji, K., Bandyopadhyay, A., Harfe, B. D., Cox, K., Kakar, S., Gerstenfeld, L., Einhorn, T., Tabin, C. J., & Rosen, V. (2006) · Nature Genetics · doi:10.1038/ng1916 · Cited by 822
Samavedi, S., Whittington, A. R., & Goldstein, A. S. (2013) · Acta Biomaterialia · doi:10.1016/j.actbio.2013.06.014 · Cited by 802
Poly(lactide-co-glycolide)/hydroxyapatite composite scaffolds for bone tissue engineering
Kim, S.-S., Sun Park, M., Jeon, O., Yong Choi, C., & Kim, B.-S. (2006) · Biomaterials · doi:10.1016/j.biomaterials.2005.08.016 · Cited by 766
Regenerating bone with bioactive glass scaffolds: A review of in vivo studies in bone defect models
El-Rashidy, A. A., Roether, J. A., Harhaus, L., Kneser, U., & Boccaccini, A. R. (2017) · Acta Biomaterialia · doi:10.1016/j.actbio.2017.08.030 · Cited by 660
Biodegradation behavior of various calcium phosphate materials in bone tissue
Klein, C. P. A. T., Driessen, A. A., de Groot, K., & van den Hooff, A. (1983) · Journal of Biomedical Materials Research · doi:10.1002/jbm.820170505 · Cited by 584
Does adult fracture repair recapitulate embryonic skeletal formation?
Ferguson, C., Alpern, E., Miclau, T., & Helms, J. A. (1999) · Mechanisms of Development · doi:10.1016/s0925-4773(99)00142-2 · Cited by 542
Mathematically defined tissue engineering scaffold architectures prepared by stereolithography
Melchels, F. P. W., Bertoldi, K., Gabbrielli, R., Velders, A. H., Feijen, J., & Grijpma, D. W. (2010) · Biomaterials · doi:10.1016/j.biomaterials.2010.05.068 · Cited by 530
The roles of signaling pathways in bone repair and regeneration
Majidinia, M., Sadeghpour, A., & Yousefi, B. (2018) · Journal of Cellular Physiology · doi:10.1002/jcp.26042 · Cited by 513
Research works printed but not linked: 2
- Key J., 1934, J. Bone Jt. Surg., 16, 176
- Bartee B. K., 1995, J. Oral Implantol., 21, 88
Cited by
Wu, Z., Bai, J., Ge, G., Wang, T., Feng, S., Ma, Q., Liang, X., Li, W., Zhang, W., Xu, Y., et al. (2022) · Advanced Healthcare Materials · doi:10.1002/adhm.202200298 · Cited by 147
Li, M., Bai, J., Tao, H., Hao, L., Yin, W., Ren, X., Gao, A., Li, N., Wang, M., Fang, S., et al. (2021) · Bioactive Materials · doi:10.1016/j.bioactmat.2021.07.002 · Cited by 122
A novel classification of bone graft materials
Wickramasinghe, M. L., Dias, G. J., & Premadasa, K. M. G. P. (2022) · Journal of Biomedical Materials Research Part B Applied Biomaterials · doi:10.1002/jbm.b.35029 · Cited by 106
3D printing of inorganic-biopolymer composites for bone regeneration
van der Heide, D., Cidonio, G., Stoddart, M. J., & D’Este, M. (2022) · Biofabrication · doi:10.1088/1758-5090/ac8cb2 · Cited by 82
Zhou, Q., Su, X., Wu, J., Zhang, X., Su, R., Ma, L., Sun, Q., & He, R. (2023) · ACS Biomaterials Science & Engineering · doi:10.1021/acsbiomaterials.2c01164 · Cited by 70
Metadata
- Authors
- Teotia, A. K., Dienel, K., Qayoom, I., van Bochove, B., Gupta, S., Partanen, J., Seppälä, J., & Kumar, A.
- Affiliations
- Indian Institute of Technology Kanpur (IN)
- Aalto University (FI)
- Polymer Technology, School of Chemical Engineering, Aalto University, Espoo 02150, Finland
- Corresponding author
- Kumar, Ashok
- ORCID
- Venue
- ACS Applied Materials & Interfaces
- Publisher
- American Chemical Society (ACS)
- Published
- 2020-09-30
- Volume
- 12
- Issue
- 43
- Pages
- 48340-48356
- ISSN
- 1944-8244 (ISSN-L)
- 1944-8252
- OpenAlex
- W3091599066
- Semantic Scholar
- c106f0a6b33b86852fc65370fa51414e0e098165
- Cited by
- 53
- References
- 62
- Citations by year
- 2026: 2 · 2025: 16 · 2024: 13 · 2023: 10 · 2022: 9 · 2021: 3
- FWCI
- 1.73
- Type
- journal article
- Language
- en
- Open access
- green
- research.aalto.fi
- Licence
- Locations
- ACS Applied Materials & Interfaces (publishedVersion)
- PubMed (publishedVersion)
- Aaltodoc (Aalto University) (submittedVersion, other-oa)
- Funders
- Indian Institute of Technology Kanpur
- Science and Engineering Research Board (IPA/2020/000026)
- Department of Biotechnology , Ministry of Science and Technology (BT/IN/Sweden/08/AK/2017-18)
- Department of Science and Technology, Ministry of Science and Technology (DST/NM/NT-2018/48)
- Ministry of Human Resource Development (MHRD_IITK_006, SPARC/2018?2019/P612/SL)
- Topics
- Physical Sciences › Engineering › Biomedical Engineering › Bone Tissue Engineering Materials
- Physical Sciences › Engineering › Biomedical Engineering › 3D Printing in Biomedical Research
- Physical Sciences › Engineering › Biomedical Engineering › Anatomy and Medical Technology
- Keywords
- bone regeneration, critical-size bone defect, 3D-printed scaffolds, composite resin, poly(trimethylene carbonate), bioactive ceramics, photocuring, cryogels, bone morphogenetic proteins, zoledronic acid, synthetic bone substitutes, rabbit tibia, porous scaffolds, biocompatibility
- MeSH terms
- Animals, Biocompatible Materials, Bone Regeneration, Male, Osteogenesis, Particle Size, Rabbits, Surface Properties, Porosity, Bone Substitutes, Tissue Scaffolds, Printing, Three-Dimensional
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
A language model drew the claims from the paper on 2026-10-11, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-11 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.