Tuning the Ionomer Distribution in the Fuel Cell Catalyst Layer with Scaling the Ionomer Aggregate Size in Dispersion
The DOI matches its Crossref record; 35 of the 35 references it cites were found in a registry or an index.
Abstract
With the demands for better performance of polymer electrolyte membrane fuel cells, studies on controlling the distribution of ionomers have recently gained interest. Here, we present a tunable ionomer distribution in the catalyst layer (CL) with dipropylene glycol (DPG) and water mixtures as the ionomer dispersion medium. Dynamic light scattering and molecular dynamics simulation demonstrate that, by increasing the DPG content in the dispersion, the size of the ionomer aggregates in the dispersion is exponentially reduced because of the higher affinity of DPG for Nafion ionomers. The ionomer distribution of the resulting CLs dictates the dimensional feature of the ionomer dispersion. Although the ionomer distribution becomes more uniform with increasing the DPG content, an optimal power performance is obtained at a DPG content of 50 wt % regardless of feed humidity because of balanced proton and mass transports. As a guide for tuning the ionomer distribution, we suggest that the ionomer aggregates in the dispersion with a size close to that of the Pt/C aggregates form a highly connected ionomer network and maintain a porosity in the catalyst/ionomer aggregate, resulting in high power performance.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“It was believed that the colloid ionomer with fine dispersion or specific size adsorbs on catalyst agglomerates, resulting in the formation of the slightly larger agglomerates, which improves the CL microstructure and enhances the porosity and then the gas transport, further the fuel cell performance [23,25,132,138,139].”
From Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells (2022) · cites this paper as [23]
In the citing paper
“The adsorbed ionomer and the amount, size, and configuration of non-absorbed ionomer and thus optimum I/C ratio are sensitive to the catalyst, ionomer, and solvent [23,91,120].”
From Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells (2022) · cites this paper as [23]
In the citing paper
“If the solvent has excellent compatibility with the main chain, e.g., dipropylene glycol [23], the main chains tend to be extended out, and the Nafion ionomer commonly appears to be well dispersed, e.g., the decreased ionomer agglomerate size or approaching solution behavior [32,128].”
From Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells (2022) · cites this paper as [23]
In the citing paper
“For example, if using dipropylene glycol (DPG)/1-propyl alcohol (NPA) and water mixtures as the solvent, the ionomer agglomerates with moderate size close to that of Pt/C agglomerates in the catalyst ink not only form a connected ionomer network, but also maintain the adequate porosity in CL [23,25], offering an improved PEM fuel cells performance.”
From Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells (2022) · cites this paper as [23]
Citations
Cites
Fast Parallel Algorithms for Short-Range Molecular Dynamics
Plimpton, S. (1995) · Journal of Computational Physics · doi:10.1006/jcph.1995.1039 · Cited by 44,721
Electronic Population Analysis on LCAO–MO Molecular Wave Functions. I
Mulliken, R. S. (1955) · The Journal of Chemical Physics · doi:10.1063/1.1740588 · Cited by 11,049
DREIDING: a generic force field for molecular simulations
Mayo, S. L., Olafson, B. D., & Goddard, W. A. (1990) · The Journal of Physical Chemistry · doi:10.1021/j100389a010 · Cited by 6,585
State of Understanding of Nafion
Mauritz, K. A., & Moore, R. B. (2004) · Chemical Reviews · doi:10.1021/cr0207123 · Cited by 4,791
Computer Simulation Using Particles
Hockney, R. W., & Eastwood, J. W. (2021) · CRC Press eBooks · doi:10.1201/9780367806934 · Cited by 4,383
Swope, W. C., Andersen, H. C., Berens, P. H., & Wilson, K. R. (1982) · The Journal of Chemical Physics · doi:10.1063/1.442716 · Cited by 4,051
New Insights into Perfluorinated Sulfonic-Acid Ionomers
Kusoglu, A., & Weber, A. Z. (2017) · Chemical Reviews · doi:10.1021/acs.chemrev.6b00159 · Cited by 2,432
Kongkanand, A., & Mathias, M. F. (2016) · The Journal of Physical Chemistry Letters · doi:10.1021/acs.jpclett.6b00216 · Cited by 1,202
Structural evolution of water swollen perfluorosulfonated ionomers from dry membrane to solution
Gebel, G. (2000) · Polymer · doi:10.1016/s0032-3861(99)00770-3 · Cited by 878
Levitt, M., Hirshberg, M., Sharon, R., Laidig, K. E., & Daggett, V. (1997) · The Journal of Physical Chemistry B · doi:10.1021/jp964020s · Cited by 561
Fuel Cell Catalyst Layers: A Polymer Science Perspective
Holdcroft, S. (2014) · Chemistry of Materials · doi:10.1021/cm401445h · Cited by 481
Soboleva, T., Zhao, X., Malek, K., Xie, Z., Navessin, T., & Holdcroft, S. (2010) · ACS Applied Materials & Interfaces · doi:10.1021/am900600y · Cited by 424
Three-dimensional analysis of Nafion layers in fuel cell electrodes
Lopez-Haro, M., Guétaz, L., Printemps, T., Morin, A., Escribano, S., Jouneau, P.-H., Bayle-Guillemaud, P., Chandezon, F., & Gebel, G. (2014) · Nature Communications · doi:10.1038/ncomms6229 · Cited by 402
Park, Y.-C., Tokiwa, H., Kakinuma, K., Watanabe, M., & Uchida, M. (2016) · Journal of Power Sources · doi:10.1016/j.jpowsour.2016.02.091 · Cited by 389
Unexplained transport resistances for low-loaded fuel-cell catalyst layers
Weber, A. Z., & Kusoglu, A. (2014) · J. Mater. Chem. A · doi:10.1039/c4ta02952f · Cited by 333
The Key to High Performance Low Pt Loaded Electrodes
Orfanidi, A., Madkikar, P., El-Sayed, H. A., Harzer, G. S., Kratky, T., & Gasteiger, H. A. (2017) · Journal of The Electrochemical Society · doi:10.1149/2.1621704jes · Cited by 276
PEMFC Catalyst Layers: The Role of Micropores and Mesopores on Water Sorption and Fuel Cell Activity
Soboleva, T., Malek, K., Xie, Z., Navessin, T., & Holdcroft, S. (2011) · ACS Applied Materials & Interfaces · doi:10.1021/am200590w · Cited by 236
Ngo, T. T., Yu, T. L., & Lin, H.-L. (2013) · Journal of Power Sources · doi:10.1016/j.jpowsour.2012.10.055 · Cited by 231
Nafion in dilute solvent systems: Dispersion or solution?
Welch, C., Labouriau, A., Hjelm, R., Orler, B., Johnston, C., & Kim, Y. S. (2012) · ACS Macro Letters · doi:10.1021/mz3005204 · Cited by 211
Lee, M., Uchida, M., Yano, H., Tryk, D. A., Uchida, H., & Watanabe, M. (2010) · Electrochimica Acta · doi:10.1016/j.electacta.2010.07.071 · Cited by 160
Influence of ionomer content on the structure and performance of PEFC membrane electrode assemblies
Xie, J., Xu, F., Wood, D. L., More, K. L., Zawodzinski, T. A., & Smith, W. H. (2010) · Electrochimica Acta · doi:10.1016/j.electacta.2010.06.067 · Cited by 149
Influence of Ionomer Content in Catalyst Layers on Direct Methanol Fuel Cell Performance
Thomas, S. C., Ren, X., & Gottesfeld, S. (1999) · Journal of The Electrochemical Society · doi:10.1149/1.1392642 · Cited by 140
Yang, F., Xin, L., Uzunoglu, A., Qiu, Y., Stanciu, L., Ilavsky, J., Li, W., & Xie, J. (2017) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.6b12949 · Cited by 124
19F NMR studies of Nafion™ ionomer adsorption on PEMFC catalysts and supporting carbons
MA, S., CHEN, Q., JOGENSEN, F., Stein, P. C., & Skou, E. M. (2007) · Solid State Ionics · doi:10.1016/j.ssi.2007.10.007 · Cited by 119
Origin of Toughness in Dispersion-Cast Nafion Membranes
Kim, Y. S., Welch, C. F., Hjelm, R. P., Mack, N. H., Labouriau, A., & Orler, E. B. (2015) · Macromolecules · doi:10.1021/ma502538k · Cited by 110
Lee, S. G., Brunello, G. F., Jang, S. S., & Bucknall, D. G. (2009) · Biomaterials · doi:10.1016/j.biomaterials.2009.07.035 · Cited by 94
Self-citationUltrathin Nafion-filled porous membrane for zinc/bromine redox flow batteries
Kim, R., Kim, H. G., Doo, G., Choi, C., Kim, S., Heo, J., Heo, J., Jung, H.-Y., & Kim, H. (2017) · Scientific Reports · doi:10.1038/s41598-017-10850-9 · Cited by 81
Self-citationHighly durable fuel cell electrodes based on ionomers dispersed in glycerol
Kim, Y. S., Welch, C. F., Mack, N. H., Hjelm, R. P., Orler, E. B., Hawley, M. E., Lee, K. S., Yim, S.-D., & Johnston, C. M. (2014) · Phys. Chem. Chem. Phys. · doi:10.1039/c4cp00496e · Cited by 75
Lee, J. H., Song, J., Lee, H., et al. (2017) · ACS Energy Letters · doi:10.1021/acsenergylett.7b00289 · Cited by 57
Self-citationSTXM Study of the Ionomer Distribution in the PEM Fuel Cell Catalyst Layers
Susac, D., Berejnov, V., Hitchcock, A. P., & Stumper, J. (2011) · ECS Transactions · doi:10.1149/1.3635596 · Cited by 47
Deswelling Mechanisms of Surface-Grafted Poly(NIPAAm) Brush: Molecular Dynamics Simulation Approach
Lee, S. G., Pascal, T. A., Koh, W., Brunello, G. F., Goddard, W. A., & Jang, S. S. (2012) · The Journal of Physical Chemistry C · doi:10.1021/jp301610b · Cited by 43
Self-citationBrunello, G. F., Lee, J. H., Lee, S. G., Choi, J. I., Harvey, D., & Jang, S. S. (2016) · RSC Advances · doi:10.1039/c6ra09274h · Cited by 40
Self-citationKim, H., You, D. J., Yoon, H., Joo, S. H., Pak, C., Chang, H., & Song, I. (2008) · Journal of Power Sources · doi:10.1016/j.jpowsour.2008.02.081 · Cited by 36
Self-citationYang, Z., Fujigaya, T., & Nakashima, N. (2015) · Journal of Power Sources · doi:10.1016/j.jpowsour.2015.09.069 · Cited by 35
Choo, M., Oh, K., Kim, H., & Park, J. (2014) · ChemSusChem · doi:10.1002/cssc.201402015 · Cited by 29
Self-citation
Cited by
Electrocatalysis in Alkaline Media and Alkaline Membrane-Based Energy Technologies
Yang, Y., Peltier, C. R., Zeng, R., Schimmenti, R., Li, Q., Huang, X., Yan, Z., Potsi, G., Selhorst, R., Lu, X., et al. (2022) · Chemical Reviews · doi:10.1021/acs.chemrev.1c00331 · Cited by 544
Du, L., Prabhakaran, V., Xie, X., Park, S., Wang, Y., & Shao, Y. (2021) · Advanced Materials · doi:10.1002/adma.201908232 · Cited by 357
(2023) · doi:10.1038/s41929-023-00949-w · Cited by 195
The Controllable Design of Catalyst Inks to Enhance PEMFC Performance: A Review
Guo, Y., Pan, F., Chen, W., Ding, Z., Yang, D., Li, B., Ming, P., & Zhang, C. (2021) · Electrochemical Energy Reviews · doi:10.1007/s41918-020-00083-2 · Cited by 175
Nano-scale control of the ionomer distribution by molecular masking of the Pt surface in PEMFCs
Doo, G., Yuk, S., Lee, J. H., Choi, S., Lee, D.-H., Lee, D. W., Hyun, J., Kwon, S. H., Lee, S. G., & Kim, H.-T. (2020) · Journal of Materials Chemistry A · doi:10.1039/c9ta14002f · Cited by 99
Self-citation
Metadata
- Authors
- Doo, G., Lee, J. H., Yuk, S., Choi, S., Lee, D.-H., Lee, D. W., Kim, H. G., Kwon, S. H., Lee, S. G., & Kim, H.-T.
- Affiliations
- Korea Advanced Institute of Science and Technology (KR)
- Pusan National University (KR)
- Corresponding author
- Lee, Seung Geol
- Kim, Hee-Tak
- ORCID
- Venue
- ACS Applied Materials & Interfaces
- Publisher
- American Chemical Society (ACS)
- Published
- 2018-05-03
- Volume
- 10
- Issue
- 21
- Pages
- 17835-17841
- ISSN
- 1944-8244 (ISSN-L)
- 1944-8252
- OpenAlex
- W2801879736
- Cited by
- 126
- References
- 35
- Citations by year
- 2026: 13 · 2025: 22 · 2024: 11 · 2023: 15 · 2022: 21 · 2021: 15 · 2020: 21 · 2019: 6 · 2018: 2
- FWCI
- 4.21
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- ACS Applied Materials & Interfaces (publishedVersion)
- PubMed (publishedVersion)
- Funders
- National Research Foundation of Korea (NRF-2015M1A2A2057127, NRF-2015M1A2A2057129)
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Fuel Cells and Related Materials
- Physical Sciences › Energy › Renewable Energy, Sustainability and the Environment › Electrocatalysts for Energy Conversion
- Physical Sciences › Materials Science › Materials Chemistry › Advancements in Solid Oxide Fuel Cells
- Keywords
- proton exchange membrane fuel cells, catalyst layer, ionomer distribution, Nafion, dipropylene glycol, ionomer dispersion, proton transport, mass transfer
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.