CoChat

Toughening Poly(l-lactide) Blends: Effectiveness of Sequence-Controlled Six-Arm Star-Branched Block Copolymers of Poly(l-lactide) and Poly(ε-caprolactone)

Open access

The DOI matches its Crossref record; 61 of the 61 references it cites were found in a registry or an index; 11 of the 31 sources its claims cite were checked for support.

Abstract

High Resolution Image Download MS PowerPoint Slide Well-defined six-arm star-branched bio-degradable block copolymers of l -lactide and ε-caprolactone were prepared using controlled ring-opening polymerization and a sequential monomer addition method using dipentaerythritol as the initiator core and organocatalysts at low temperatures in solution. Sequence of enchainment was changed by reversing the order of monomer addition giving, either, a crystalline PLA block or an amorphous PCL block as the outer segment. Well-defined six-arm poly(ε-caprolactone- b - l -lactide, 6s-PCL- b -PLA) block copolymers were obtained with a range of segment molecular weights. However, in the case of six-arm poly( l -lactide- b -ε-caprolactone, 6s-PLA- b -PCL), disruption of the block structure was observed on account of competing transesterification reactions accompanying a chain-growth reaction. Such sequence-controlled block copolymers showed interesting phase morphologies, as evidenced by differential scanning calorimetry (DSC) studies. 6s-PCL- b -PLA showed two glass-transition temperatures and two melting temperatures characteristic of the amorphous and crystalline blocks. 6s-PCL- b -PLA and 6s-PLA- b -PCL with different segment chain lengths were solution blended (10 wt %) with a commercially sourced PLA. All the blends were highly transparent. The structure and properties of the blend were examined by DSC, measurement of mechanical properties, and scanning electron microscopy. The results show that a phase-separated 6s-PCL- b -PLA copolymer results in two- to three-fold improvement in tensile toughness without the loss of modulus. A possible hypothesis for the mechanism of tensile toughness in the blend has been proposed.

Overview

CoChat Summary

## TL;DR

The paper reports that sequence-controlled six-arm star-branched PLA/PCL block copolymers can toughen PLA while preserving modulus, with the best performance from 6s-PCL-b-PLA. The authors argue that block sequence, segment molecular weight, and phase morphology strongly affect crystallization and tensile behavior.

## Key findings

  • Six-arm star-branched block copolymers 6s-PCL-b-PLA and 6s-PLA-b-PCL were synthesized by sequential ring-opening polymerization in solution at low temperature, with targeted nominal Mn of 30,000, 50,000, and 70,000 g/mol.
  • 6s-PCL-b-PLA was “well-defined,” while 6s-PLA-b-PCL showed disruption of block structure due to transesterification; all polymerization reactions were reported as well controlled with dispersities (Đ) in the range of 1.20 to 1.35 and Ieff generally between 0.90 and 0.95.
  • Adding 10 wt % of either block copolymer to PLA improved % elongation at break with no significant loss of modulus; the paper states the best blend gave a two- to three-fold improvement in elongation at break without loss of modulus.
  • The strongest improvement was observed for blends with block copolymers around Mn 46,000–47,000 g/mol; the paper notes poorer performance when Mn increased to about 66,000 g/mol and when the PLA segment was around 46,000 g/mol.

## Methods

  • Sequential ring-opening polymerization was used to synthesize six-arm star-branched PCL and PLA macroinitiators and then block copolymers, using dipentaerythritol as the hexafunctional initiator; DBU catalyzed lactide polymerization and diphenyl phosphate (DPP) catalyzed ε-caprolactone polymerization.
  • The PLA blend samples were prepared by solution blending 0.9 g PLA with 0.1 g block copolymer in dry dichloromethane, then cast into films by doctor blade and dried.
  • Characterization included GPC, 1H and 13C NMR, DSC, tensile testing on five dumbbell specimens per sample, and SEM of fracture surfaces.

## Limitations

  • The authors explicitly say that “further studies will be necessary” or “will be needed” to better understand the morphology, tensile toughening, and crystallization behavior, especially for 6s-PLA-b-PCL and the influence of monomer sequence.
  • They note that some transesterification occurred during preparation of 6s-PLA-b-PCL, which complicates interpretation of that copolymer’s structure and properties.
  • Evident from the text: the blend study is limited to 10 wt % additive in PLA, so the reported performance is not shown across a broader composition range.

Model-written summary. Check it against the paper before relying on it.

Integrity signals

Registry

Crossref · 10.1021/acsomega.1c04486

Cites

61 of 61 references verified0 citation errors · 0 not checkable

Statistics

Nothing to recompute.

Figures

Scheme 1 Synthesis of the 6s-PCL-b-PLA Block Copolymer
Scheme 1 Synthesis of the 6s-PCL-b-PLA Block CopolymerCC BY-NC-ND · PubMed Central
Scheme 2 Synthesis of the 6s-PLA-b-PCL Block Copolymer
Scheme 2 Synthesis of the 6s-PLA-b-PCL Block CopolymerCC BY-NC-ND · PubMed Central
Figure 1 DSC curves of (a) PLA and its blends with (b) 1a (6s-PCL-b-PLA, Mn = 27,300 g/mol), (c) 1b (6s-PCL-b-PLA, Mn = 47,850 g/mol), (d) 1c (6s-PCL-b-PLA, Mn = 66,100 g/mol), (e) 2a (6s-PLA-b-PCL, Mn = 27,750 g/mol), (f) 2b (6s-PLA-b-PCL, Mn = 46,500 g/mol), and (g) 2c (6s-PLA-b-PCL, Mn = 66,350 g/mol).
Figure 1 DSC curves of (a) PLA and its blends with (b) 1a (6s-PCL-b-PLA, Mn = 27,300 g/mol), (c) 1b (6s-PCL-b-PLA, Mn = 47,850 g/mol), (d) 1c (6s-PCL-b-PLA, Mn = 66,100 g/mol), (e) 2a (6s-PLA-b-PCL, Mn = 27,750 g/mol), (f) 2b (6s-PLA-b-PCL, Mn = 46,500 g/mol), and (g) 2c (6s-PLA-b-PCL, Mn = 66,350 g/mol).CC BY-NC-ND · PubMed Central
Figure 2 Mechanical properties of PLA and 1a: (6s-PCL-b-PLA, Mn = 27,300 g/mol), 1b: (6s-PCL-b-PLA, Mn = 47,850 g/mol), 1c: (6s-PCL-b-PLA, Mn = 66,100 g/mol), 2a: (6s-PLA-b-PCL, Mn = 27,750 g/mol), 2b: (6s-PLA-b-PCL, Mn = 46,500 g/mol), and 2c: (6s-PLA-b-PCL, Mn = 66,350 g/mol).
Figure 2 Mechanical properties of PLA and 1a: (6s-PCL-b-PLA, Mn = 27,300 g/mol), 1b: (6s-PCL-b-PLA, Mn = 47,850 g/mol), 1c: (6s-PCL-b-PLA, Mn = 66,100 g/mol), 2a: (6s-PLA-b-PCL, Mn = 27,750 g/mol), 2b: (6s-PLA-b-PCL, Mn = 46,500 g/mol), and 2c: (6s-PLA-b-PCL, Mn = 66,350 g/mol).CC BY-NC-ND · PubMed Central
Figure 3 SEM of fractured surfaces of PLA and blends, PLA/6s-PCL-b-PLA and PLA/6s-PLA-b-PCL, after break of dumb-bell shaped specimens during tensile testing “[A: PLA; B: PLA+ 1a (6s-PCL-b-PLA, Mn = 27,300 g/mol); C: PLA + 1b (6s-PCL-b-PLA, Mn = 47,850 g/mol); D: PLA+ 1c (6s-PCL-b-PLA, Mn = 66,100 g/mol): E: PLA+ 2a (6s-PLA-b-PCL, Mn = 27,750 g/mol); F: PLA+2b (6s-PLA-b-PCL, Mn = 46,500 g/mol); and G: PLA+2c (6s-PLA-b-PCL, Mn = 66,350 g/mol)]”.
Figure 3 SEM of fractured surfaces of PLA and blends, PLA/6s-PCL-b-PLA and PLA/6s-PLA-b-PCL, after break of dumb-bell shaped specimens during tensile testing “[A: PLA; B: PLA+ 1a (6s-PCL-b-PLA, Mn = 27,300 g/mol); C: PLA + 1b (6s-PCL-b-PLA, Mn = 47,850 g/mol); D: PLA+ 1c (6s-PCL-b-PLA, Mn = 66,100 g/mol): E: PLA+ 2a (6s-PLA-b-PCL, Mn = 27,750 g/mol); F: PLA+2b (6s-PLA-b-PCL, Mn = 46,500 g/mol); and G: PLA+2c (6s-PLA-b-PCL, Mn = 66,350 g/mol)]”.CC BY-NC-ND · PubMed Central

Verification

Claims the paper makes

4 Valid · 3 Not valid · 14 Not checked · 87 Own results and interpretations

71 more claims

Create a free account to see all 108 claims and every source verdict.

See all claims — free account
  • Probably not a substantial claim. 17
  • It may state two separate claims as one. 19

Create a free account to see these claims.

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

1 of 1

Citations

Cites

Research works printed but not linked: 2

  1. 10.1007/s00289-016-1713-4 · DOI
  2. Witzke, D. R. Introduction to Properties, Engineering and Prospects of Polylactide Polymers. Ph.D. Thesis; Michigan State University: East Lansing, MI, 1999; p 389.

Cited by

See all 21

Metadata

Authors
Deokar, M. D., Garnaik, B., & Sivaram, S.
Affiliations
  • National Chemical Laboratory (IN)
  • Indian Institute of Science Education and Research Pune (IN)
Corresponding author
Sivaram, Swaminathan
Venue
ACS Omega
Published
2022-03-09
Volume
7
Issue
11
Pages
9118-9129
ISSN
2470-1343 (ISSN-L)
OpenAlex
W4220760098
Cited by
21
References
60
Citations by year
2026: 4 · 2025: 4 · 2024: 4 · 2023: 6 · 2022: 3
FWCI
1.06
Type
journal article
Language
en
Open access
Locations
  • ACS Omega (publishedVersion, cc-by-nc-nd)
  • PubMed Central (publishedVersion, cc-by-nc-nd)
  • PubMed (publishedVersion)
  • DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion)
Funders
  • Indian National Science Academy
  • Council of Scientific and Industrial Research
Topics
  • Physical Sciences › Materials Science › Biomaterials › biodegradable polymer synthesis and properties
  • Physical Sciences › Materials Science › Polymers and Plastics › Polymer crystallization and properties
  • Physical Sciences › Materials Science › Materials Chemistry › Block Copolymer Self-Assembly
Keywords
poly(L-lactic acid), polycaprolactone, sequence-controlled polymerization, ring-opening polymerization, organocatalysts, transesterification, polymer blends, tensile toughness, phase separation, biodegradable polymers

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

The claim verdicts this report counts are experimental: their accuracy is not yet measured.

A language model drew the claims from the paper on 2026-09-30, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).

A second model labelled each claim on 2026-09-30 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).

Cited sources are checked with a language model’s help (gpt-6-sol).

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.