Effects of Temperature on the Formation of Lignin-Derived Oligomers during the Fast Pyrolysis of Mallee Woody Biomass
The DOI matches its Crossref record; 34 of the 34 references it cites were found in a registry or an index.
Abstract
This paper reports the evolution of the composition of bio-oil obtained from the fast pyrolysis of Mallee woody biomass as a function of temperature between 350 and 580 °C. Several analytical techniques were used to quantify bio-oil composition. For the volatile components, the results obtained by gas chromatography−mass spectrometry and Karl Fischer titration agree very well with those obtained by thermogravimetric analyses. However, for the heavy components, especially lignin-derived oligomers, synchronous UV-fluorescence spectroscopy and thermogravimetric analysis give more reliable results than the precipitation in cold water. Our results indicate that the accuracy of the precipitation methods to quantify lignin-derived oligomer in bio-oil is limited by the relatively large amounts of small oligomers remaining soluble in a metastable form in cold water. A maximum in the yield of lignin-derived oligomers was observed between 450 and 500 °C. In fact, most of the increases in the yield of bio-oil with increasing temperature above 350 °C can be explained by the formation of this type of oligomers. Increases in the rates at which the oligomers are formed and increases in their volatility at elevated temperature are the main reasons for the increased presence of oligomers in bio-oil produced at temperatures higher than 350 °C.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“From Fig. 5, the obtained products can be mainly categorized as guaiacyl, cresol, and catechol types, where guaiacyl units are suggested to produce G-type phenols via depolymerization and dehydration (P1) [165].”
From A review on lignin pyrolysis: pyrolytic behavior, mechanism, and relevant upgrading for improving process efficiency (2022) · cites this paper as [165]
Citations
Cites
An overview of fast pyrolysis of biomass
Bridgwater, A. V., Meier, D., & Radlein, D. (1999) · Organic Geochemistry · doi:10.1016/s0146-6380(99)00120-5 · Cited by 1,752
Characterization of bio-oils in chemical families
Garcia-Perez, M., Chaala, A., Pakdel, H., Kretschmer, D., & Roy, C. (2007) · Biomass and Bioenergy · doi:10.1016/j.biombioe.2006.02.006 · Cited by 498
Scholze, B., & Meier, D. (2001) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/s0165-2370(00)00110-8 · Cited by 496
State of the art of applied fast pyrolysis of lignocellulosic materials — a review
Meier, D., & Faix, O. (1999) · Bioresource Technology · doi:10.1016/s0960-8524(98)00086-8 · Cited by 417
GC/MS Characterization of Liquids Generated from Low-Temperature Pyrolysis of Wood
Branca, C., Giudicianni, P., & Di Blasi, C. (2003) · Industrial & Engineering Chemistry Research · doi:10.1021/ie030066d · Cited by 405
Characterization of biomass-based flash pyrolysis oils
Sipilä, K., Kuoppala, E., Fagernäs, L., & Oasmaa, A. (1998) · Biomass and Bioenergy · doi:10.1016/s0961-9534(97)10024-1 · Cited by 404
Garcia-Perez, M., Wang, X. S., Shen, J., Rhodes, M. J., Tian, F., Lee, W.-J., Wu, H., & Li, C.-Z. (2008) · Industrial & Engineering Chemistry Research · doi:10.1021/ie071497p · Cited by 391
Self-citationOn the mechanism of the rapid pyrolysis of cellulose
Piskorz, J., Radlein, D., & Scott, D. S. (1986) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/0165-2370(86)85003-3 · Cited by 361
Additives To Lower and Stabilize the Viscosity of Pyrolysis Oils during Storage
Diebold, J. P., & Czernik, S. (1997) · Energy & Fuels · doi:10.1021/ef9700339 · Cited by 360
Characterization of the water-insoluble fraction from fast pyrolysis liquids (pyrolytic lignin)
Scholze, B., Hanser, C., & Meier, D. (2001) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/s0165-2370(00)00173-x · Cited by 291
Stability of wood fast pyrolysis oil
Czernik, S., Johnson, D. K., & Black, S. (1994) · Biomass and Bioenergy · doi:10.1016/0961-9534(94)00058-2 · Cited by 260
The continuous flash pyrolysis of biomass
Scott, D. S., & Piskorz, J. (1984) · The Canadian Journal of Chemical Engineering · doi:10.1002/cjce.5450620319 · Cited by 254
The role of temperature in the fast pyrolysis of cellulose and wood
Scott, D. S., Piskorz, J., Bergougnou, M. A., Graham, R., & Overend, R. P. (1988) · Industrial & Engineering Chemistry Research · doi:10.1021/ie00073a003 · Cited by 241
The flash pyrolysis of aspen‐poplar wood
Scott, D. S., & Piskorz, J. (1982) · The Canadian Journal of Chemical Engineering · doi:10.1002/cjce.5450600514 · Cited by 234
Itoh, H., Wada, M., Honda, Y., Kuwahara, M., & Watanabe, T. (2003) · Journal of Biotechnology · doi:10.1016/s0168-1656(03)00123-8 · Cited by 233
Biomass Pyrolysis in a Fluidized Bed Reactor. Part 1: Literature Review and Model Simulations
Kersten, S. R. A., Wang, X., Prins, W., & van Swaaij, W. P. M. (2005) · Industrial & Engineering Chemistry Research · doi:10.1021/ie0504856 · Cited by 233
Inorganic Compounds in Biomass Feedstocks. 1. Effect on the Quality of Fast Pyrolysis Oils
Agblevor, F. A., & Besler, S. (1996) · Energy & Fuels · doi:10.1021/ef950202u · Cited by 222
A second look at fast pyrolysis of biomass—the RTI process
Scott, D. S., Majerski, P., Piskorz, J., & Radlein, D. (1999) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/s0165-2370(99)00006-6 · Cited by 215
Vacuum pyrolysis of softwood and hardwood biomass
Garcìa-Pérez, M., Chaala, A., Pakdel, H., Kretschmer, D., & Roy, C. (2007) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2006.05.003 · Cited by 203
Pyrolysis reactions of various lignin model dimers
Kawamoto, H., Horigoshi, S., & Saka, S. (2007) · Journal of Wood Science · doi:10.1007/s10086-006-0834-z · Cited by 196
Fast pyrolysis of natural polysaccharides as a potential industrial process
Radlein, D., Piskorz, J., & Scott, D. S. (1991) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/0165-2370(91)80034-6 · Cited by 183
Characterization of the water-insoluble fraction from fast pyrolysis liquids (pyrolytic lignin)
Bayerbach, R., Nguyen, V. D., Schurr, U., & Meier, D. (2006) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2006.02.002 · Cited by 158
Flash pyrolysis of cellulose for production of anhydro-oligomers
Piskorz, J., Majerski, P., Radlein, D. S. A. G., Vladars-Usas, A., & Scott, D. S. (2000) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/s0165-2370(00)00089-9 · Cited by 157
Fast pyrolysis of sweet sorghum and sweet sorghum bagasse
Piskorz, J., Majerski, P., Radlein, D. S. A. G., Scott, D. S., & Bridgwater, A. V. (1998) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/s0165-2370(98)00067-9 · Cited by 139
UV-Fluorescence Spectroscopy of Coal Pyrolysis Tars
Li, C., Wu, F., Cai, H., & Kandiyoti, R. (1994) · Energy & Fuels · doi:10.1021/ef00047a006 · Cited by 127
Self-citationMultiphase Structure of Bio-oils
Garcı̀a-Pèrez, M., Chaala, A., Pakdel, H., Kretschmer, D., Rodrigue, D., & Roy, C. (2005) · Energy & Fuels · doi:10.1021/ef050248f · Cited by 125
Production and Fuel Properties of Pine Chip Bio-oil/Biodiesel Blends
Garcia-Perez, M., Adams, T. T., Goodrum, J. W., Geller, D. P., & Das, K. C. (2007) · Energy & Fuels · doi:10.1021/ef060533e · Cited by 118
On the presence of anhydro-oligosaccharides in the sirups from the fast pyrolysis of cellulose
Radlein, D. S. A. G., Grinshpun, A., Piskorz, J., & Scott, D. S. (1987) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/0165-2370(87)80013-x · Cited by 94
Characterisation of oligomers and sugar ring-cleavage products in the pyrolysate of cellulose
Lomax, J. A., Commandeur, J., Arisz, P. W., & Boon, J. J. (1991) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/0165-2370(91)80035-7 · Cited by 81
Effects of side-chain hydroxyl groups on pyrolytic β-ether cleavage of phenolic lignin model dimer
Kawamoto, H., Horigoshi, S., & Saka, S. (2006) · Journal of Wood Science · doi:10.1007/s10086-006-0839-7 · Cited by 80
Multistep Mechanism for the Devolatilization of Biomass Fast Pyrolysis Oils
Branca, C., & Blasi, C. D. (2006) · Industrial & Engineering Chemistry Research · doi:10.1021/ie060161x · Cited by 75
Evaluation of the Influence of Stainless Steel and Copper on the Aging Process of Bio-Oil
Garcìa-Pèrez, M., Chaala, A., Pakdel, H., Kretschmer, D., Rodrigue, D., & Roy, C. (2006) · Energy & Fuels · doi:10.1021/ef050344g · Cited by 53
Kershaw, J. R., Sathe, C., Hayashi, J., Li, C., & Chiba, T. (2000) · Energy & Fuels · doi:10.1021/ef990181u · Cited by 52
Self-citationPeacocke, G. V. C., Madrali, E. S., Li, C., Güell, A. J., Wu, F., Kandiyoti, R., & Bridgwater, A. V. (1994) · Biomass and Bioenergy · doi:10.1016/0961-9534(94)00055-x · Cited by 35
Self-citation
Research works printed but not linked: 3
- Daugaard D. E., 2006, Proceedings of Science in Thermal and Chemical Biomass Conversion, 1189
- Pakdel H, 2006, Proceedings of Science in Thermal and Chemical Biomass Conversion, 1189
- Nukamura, T.; Kawamoto, H.; Saka, S.Pyrolysis behavior of Japonese cedar wood lignin studied with various model dimers.J. Anal. Appl. Pyrolysis, in press.
Cited by
A review of recent laboratory research and commercial developments in fast pyrolysis and upgrading
Butler, E., Devlin, G., Meier, D., & McDonnell, K. (2011) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2011.07.035 · Cited by 471
“As the pyrolysis temperature is increased, the content of water insoluble compounds, and consequently the molecular weight and viscosity of the biooil increase) [95, 97, 98].”
BackgroundUnderstanding the Fast Pyrolysis of Lignin
Patwardhan, P. R., Brown, R. C., & Shanks, B. H. (2011) · ChemSusChem · doi:10.1002/cssc.201100133 · Cited by 468
Comparison of the pyrolysis behavior of lignins from different tree species
Wang, S., Wang, K., Liu, Q., Gu, Y., Luo, Z., Cen, K., & Fransson, T. (2009) · Biotechnology Advances · doi:10.1016/j.biotechadv.2009.04.010 · Cited by 405
Self-citationEffects of particle size on the fast pyrolysis of oil mallee woody biomass
Shen, J., Wang, X.-S., Garcia-Perez, M., Mourant, D., Rhodes, M. J., & Li, C.-Z. (2009) · Fuel · doi:10.1016/j.fuel.2009.05.001 · Cited by 376
Self-citationLu, X., & Gu, X. (2022) · Biotechnology for Biofuels and Bioproducts · doi:10.1186/s13068-022-02203-0 · Cited by 354
“5, the obtained products can be mainly categorized as guaiacyl, cresol, and catechol types, where guaiacyl units are suggested to produce G-type phenols via depolymerization and dehydration (P1) [165].”
Background
Metadata
- Authors
- Garcia-Perez, M., Wang, S., Shen, J., Rhodes, M., Lee, W. J., & Li, C.-Z.
- Affiliations
- Department of Chemical Engineering, PO Box 36, Monash University, Victoria 3800, Australia; Biological Systems Engineering Department, Washington State University, Pullman, Washington 99164; and Department of Chemical Engineering, Taiyuan University of Technology, Shanxi 030024, P. R. China
- Monash University (AU)
- Corresponding author
- Li, Chun-Zhu
- Venue
- Energy & Fuels
- Publisher
- American Chemical Society (ACS)
- Published
- 2008-03-22
- Volume
- 22
- Issue
- 3
- Pages
- 2022-2032
- ISSN
- 0887-0624 (ISSN-L)
- 1520-5029
- OpenAlex
- W1980687513
- Cited by
- 235
- References
- 34
- Citations by year
- 2025: 7 · 2024: 6 · 2023: 7 · 2022: 6 · 2021: 13 · 2020: 15 · 2019: 10 · 2018: 12 · 2017: 19 · 2016: 24 · 2015: 13 · 2014: 16 · 2013: 23 · 2012: 21
- FWCI
- 9.50
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- Energy & Fuels (publishedVersion)
- eSpace (Curtin University) (submittedVersion)
- Topics
- Physical Sciences › Energy › Fuel Technology › Thermochemical Biomass Conversion Processes
- Physical Sciences › Energy › Fuel Technology › Mining and Gasification Technologies
- Physical Sciences › Chemical Engineering › Fluid Flow and Transfer Processes › Advanced Combustion Engine Technologies
- Keywords
- fast pyrolysis, bio-oil composition, pyrolysis temperature, bio-oil yield, volatile compounds, heavy components
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.