Effects of Temperature on the Formation of Lignin-Derived Oligomers during the Fast Pyrolysis of Mallee Woody Biomass
The DOI matches its Crossref record; 34 of the 34 references it cites were found in a registry or an index.
Abstract
This paper reports the evolution of the composition of bio-oil obtained from the fast pyrolysis of Mallee woody biomass as a function of temperature between 350 and 580 °C. Several analytical techniques were used to quantify bio-oil composition. For the volatile components, the results obtained by gas chromatography−mass spectrometry and Karl Fischer titration agree very well with those obtained by thermogravimetric analyses. However, for the heavy components, especially lignin-derived oligomers, synchronous UV-fluorescence spectroscopy and thermogravimetric analysis give more reliable results than the precipitation in cold water. Our results indicate that the accuracy of the precipitation methods to quantify lignin-derived oligomer in bio-oil is limited by the relatively large amounts of small oligomers remaining soluble in a metastable form in cold water. A maximum in the yield of lignin-derived oligomers was observed between 450 and 500 °C. In fact, most of the increases in the yield of bio-oil with increasing temperature above 350 °C can be explained by the formation of this type of oligomers. Increases in the rates at which the oligomers are formed and increases in their volatility at elevated temperature are the main reasons for the increased presence of oligomers in bio-oil produced at temperatures higher than 350 °C.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“From Fig. 5, the obtained products can be mainly categorized as guaiacyl, cresol, and catechol types, where guaiacyl units are suggested to produce G-type phenols via depolymerization and dehydration (P1) [165].”
From A review on lignin pyrolysis: pyrolytic behavior, mechanism, and relevant upgrading for improving process efficiency (2022) · cites this paper as [165]
Citations
Cites
An overview of fast pyrolysis of biomass
Bridgwater, A. V., Meier, D., & Radlein, D. (1999) · Organic Geochemistry · doi:10.1016/s0146-6380(99)00120-5 · Cited by 1,752
Characterization of bio-oils in chemical families
Garcia-Perez, M., Chaala, A., Pakdel, H., Kretschmer, D., & Roy, C. (2007) · Biomass and Bioenergy · doi:10.1016/j.biombioe.2006.02.006 · Cited by 498
Scholze, B., & Meier, D. (2001) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/s0165-2370(00)00110-8 · Cited by 496
State of the art of applied fast pyrolysis of lignocellulosic materials — a review
Meier, D., & Faix, O. (1999) · Bioresource Technology · doi:10.1016/s0960-8524(98)00086-8 · Cited by 417
GC/MS Characterization of Liquids Generated from Low-Temperature Pyrolysis of Wood
Branca, C., Giudicianni, P., & Di Blasi, C. (2003) · Industrial & Engineering Chemistry Research · doi:10.1021/ie030066d · Cited by 405
Characterization of biomass-based flash pyrolysis oils
Sipilä, K., Kuoppala, E., Fagernäs, L., & Oasmaa, A. (1998) · Biomass and Bioenergy · doi:10.1016/s0961-9534(97)10024-1 · Cited by 404
Garcia-Perez, M., Wang, X. S., Shen, J., Rhodes, M. J., Tian, F., Lee, W.-J., Wu, H., & Li, C.-Z. (2008) · Industrial & Engineering Chemistry Research · doi:10.1021/ie071497p · Cited by 391
Self-citationOn the mechanism of the rapid pyrolysis of cellulose
Piskorz, J., Radlein, D., & Scott, D. S. (1986) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/0165-2370(86)85003-3 · Cited by 361
Additives To Lower and Stabilize the Viscosity of Pyrolysis Oils during Storage
Diebold, J. P., & Czernik, S. (1997) · Energy & Fuels · doi:10.1021/ef9700339 · Cited by 360
Characterization of the water-insoluble fraction from fast pyrolysis liquids (pyrolytic lignin)
Scholze, B., Hanser, C., & Meier, D. (2001) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/s0165-2370(00)00173-x · Cited by 291
Research works printed but not linked: 3
- Daugaard D. E., 2006, Proceedings of Science in Thermal and Chemical Biomass Conversion, 1189
- Pakdel H, 2006, Proceedings of Science in Thermal and Chemical Biomass Conversion, 1189
- Nukamura, T.; Kawamoto, H.; Saka, S.Pyrolysis behavior of Japonese cedar wood lignin studied with various model dimers.J. Anal. Appl. Pyrolysis, in press.
Cited by
A review of recent laboratory research and commercial developments in fast pyrolysis and upgrading
Butler, E., Devlin, G., Meier, D., & McDonnell, K. (2011) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2011.07.035 · Cited by 471
“As the pyrolysis temperature is increased, the content of water insoluble compounds, and consequently the molecular weight and viscosity of the biooil increase) [95, 97, 98].”
BackgroundUnderstanding the Fast Pyrolysis of Lignin
Patwardhan, P. R., Brown, R. C., & Shanks, B. H. (2011) · ChemSusChem · doi:10.1002/cssc.201100133 · Cited by 468
Comparison of the pyrolysis behavior of lignins from different tree species
Wang, S., Wang, K., Liu, Q., Gu, Y., Luo, Z., Cen, K., & Fransson, T. (2009) · Biotechnology Advances · doi:10.1016/j.biotechadv.2009.04.010 · Cited by 405
Self-citationEffects of particle size on the fast pyrolysis of oil mallee woody biomass
Shen, J., Wang, X.-S., Garcia-Perez, M., Mourant, D., Rhodes, M. J., & Li, C.-Z. (2009) · Fuel · doi:10.1016/j.fuel.2009.05.001 · Cited by 376
Self-citationLu, X., & Gu, X. (2022) · Biotechnology for Biofuels and Bioproducts · doi:10.1186/s13068-022-02203-0 · Cited by 354
“5, the obtained products can be mainly categorized as guaiacyl, cresol, and catechol types, where guaiacyl units are suggested to produce G-type phenols via depolymerization and dehydration (P1) [165].”
BackgroundCurrent technologies for analysis of biomass thermochemical processing: A review
Bahng, M.-K., Mukarakate, C., Robichaud, D. J., & Nimlos, M. R. (2009) · Analytica Chimica Acta · doi:10.1016/j.aca.2009.08.016 · Cited by 319
Mourant, D., Wang, Z., He, M., Wang, X. S., Garcia-Perez, M., Ling, K., & Li, C.-Z. (2011) · Fuel · doi:10.1016/j.fuel.2011.04.033 · Cited by 314
Self-citationState-of-the-art of fast pyrolysis in IEA bioenergy member countries
Meier, D., van de Beld, B., Bridgwater, A. V., Elliott, D. C., Oasmaa, A., & Preto, F. (2013) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2012.11.061 · Cited by 295
“Li in Australia, where they are studying mallee wood pyrolysis in a fluidized-bed reactor [79–81].”
BackgroundHydrotreatment of pyrolysis bio-oil: A review
Han, Y., Gholizadeh, M., Tran, C.-C., Kaliaguine, S., Li, C.-Z., Olarte, M., & Garcia-Perez, M. (2019) · Fuel Processing Technology · doi:10.1016/j.fuproc.2019.106140 · Cited by 292
Self-citationGaladima, A., & Muraza, O. (2015) · Energy Conversion and Management · doi:10.1016/j.enconman.2015.07.078 · Cited by 246
How well can renewable resources mimic commodity monomers and polymers?
Mathers, R. T. (2012) · Journal of Polymer Science Part A: Polymer Chemistry · doi:10.1002/pola.24939 · Cited by 237
Effect of torrefaction on structure and fast pyrolysis behavior of corncobs
Zheng, A., Zhao, Z., Chang, S., Huang, Z., Wang, X., He, F., & Li, H. (2013) · Bioresource Technology · doi:10.1016/j.biortech.2012.10.067 · Cited by 242
“…thermal decomposition process that occurs in an inert atmosphere using high heating rates (103–104 K/s) and short residence times (<2 s) at about 450–550 C to maximize liquid production with solid char and non-condensable gas as low yield co-products (Bridgwater, 1999; Garcia-Perez et al., 2008b).”
BackgroundFormation of phenolic oligomers during fast pyrolysis of lignin
Bai, X., Kim, K. H., Brown, R. C., Dalluge, E., Hutchinson, C., Lee, Y. J., & Dalluge, D. (2014) · Fuel · doi:10.1016/j.fuel.2014.03.013 · Cited by 234
An FT-IR spectroscopic study of carbonyl functionalities in bio-oils
Lievens, C., Mourant, D., He, M., Gunawan, R., Li, X., & Li, C.-Z. (2011) · Fuel · doi:10.1016/j.fuel.2011.06.001 · Cited by 219
“Many analytical techniques can be used to provide some information about the carbonyl functionalities in a bio-oil [3,10–13].”
BackgroundMethodSelf-citationPecha, M. B., Arbelaez, J. I. M., Garcia-Perez, M., Chejne, F., & Ciesielski, P. N. (2019) · Green Chemistry · doi:10.1039/c9gc00585d · Cited by 203
Separation, hydrolysis and fermentation of pyrolytic sugars to produce ethanol and lipids
Lian, J., Chen, S., Zhou, S., Wang, Z., O’Fallon, J., Li, C.-Z., & Garcia-Perez, M. (2010) · Bioresource Technology · doi:10.1016/j.biortech.2010.07.071 · Cited by 209
Self-citationCharacteristics and mechanism study of analytical fast pyrolysis of poplar wood
Dong, C.-Q., Zhang, Z.-F., Lu, Q., & Yang, Y.-P. (2012) · Energy Conversion and Management · doi:10.1016/j.enconman.2011.12.012 · Cited by 209
“Fast pyrolysis of lignin will obtain higher char yield than the holocellulose, and the liquid product mainly includes the large molecular oligomers (known as pyrolytic lignins), the monomeric phenolic compounds, aswell as light linear compounds [25–28].”
BackgroundFractional Condensation of Biomass Pyrolysis Vapors
Westerhof, R. J. M., Brilman, D. W. F., Garcia-Perez, M., Wang, Z., Oudenhoven, S. R. G., van Swaaij, W. P. M., & Kersten, S. R. A. (2011) · Energy & Fuels · doi:10.1021/ef2000322 · Cited by 195
Azeez, A. M., Meier, D., Odermatt, J., & Willner, T. (2010) · Energy & Fuels · doi:10.1021/ef9012856 · Cited by 194
Yu, Y., & Wu, H. (2010) · Industrial & Engineering Chemistry Research · doi:10.1021/ie901925g · Cited by 175
Min, Z., Asadullah, M., Yimsiri, P., Zhang, S., Wu, H., & Li, C.-Z. (2011) · Fuel · doi:10.1016/j.fuel.2010.12.039 · Cited by 178
“The mallee biomass, with a lot of special features, is grown in Western Australia to combat the dryland salinity problem and represents a substantial biomass resource for energy and chemicals [20–26].”
BackgroundSelf-citationPyrolysis Oil Multiphase Behavior and Phase Stability: A Review
Oasmaa, A., Fonts, I., Pelaez-Samaniego, M. R., Garcia-Perez, M. E., & Garcia-Perez, M. (2016) · Energy & Fuels · doi:10.1021/acs.energyfuels.6b01287 · Cited by 167
In situ characterization of functional groups of biochar in pyrolysis of cellulose
Fan, M., Li, C., Sun, Y., Zhang, L., Zhang, S., & Hu, X. (2021) · Science of The Total Environment · doi:10.1016/j.scitotenv.2021.149354 · Cited by 173
Self-citationEvolution of Aromatic Structures during the Low-Temperature Electrochemical Upgrading of Bio-oil
Deng, W., Xu, K., Xiong, Z., Chaiwat, W., Wang, X., Su, S., Hu, S., Qiu, J., Wang, Y., & Xiang, J. (2019) · Energy & Fuels · doi:10.1021/acs.energyfuels.9b03099 · Cited by 180
Jones, S. B., Meyer, P. A., Snowden-Swan, L. J., Padmaperuma, A. B., Tan, E., Dutta, A., Jacobson, J., & Cafferty, K. (2013) · doi:10.2172/1115839 · Cited by 176
Zhou, S., Xue, Y., Sharma, A. M., & Bai, X. (2016) · ACS Sustainable Chemistry & Engineering · doi:10.1021/acssuschemeng.6b01488 · Cited by 170
Quantification of Bio-Oil Functional Groups and Evidences of the Presence of Pyrolytic Humins
Stankovikj, F., McDonald, A. G., Helms, G. L., & Garcìa-Pèrez, M. (2016) · Energy & Fuels · doi:10.1021/acs.energyfuels.6b01242 · Cited by 167
Formation of Aromatic Structures during the Pyrolysis of Bio-oil
Wang, Y., Li, X., Mourant, D., Gunawan, R., Zhang, S., & Li, C.-Z. (2012) · Energy & Fuels · doi:10.1021/ef201155e · Cited by 155
Self-citationZheng, A., Zhao, Z., Chang, S., Huang, Z., Zhao, K., Wei, G., He, F., & Li, H. (2014) · Bioresource Technology · doi:10.1016/j.biortech.2014.10.157 · Cited by 153
Fast Pyrolysis of Pine Sawdust in a Fluidized-Bed Reactor
DeSisto, W. J., Hill, N., Beis, S. H., Mukkamala, S., Joseph, J., Baker, C., Ong, T.-H., Stemmler, E. A., Wheeler, M. C., Frederick, B. G., et al. (2010) · Energy & Fuels · doi:10.1021/ef901120h · Cited by 142
Liaw, S., Wang, Z., Ndegwa, P. M., Frear, C. S., Ha, S., Li, C., & Garcìa-Pèrez, M. (2011) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2011.09.011 · Cited by 145
Self-citationNational Renewable Energy Lab. (NREL), G., Jones, S. B., Bioenergy Technologies Office (EE-3B) USDOE Office of Energy Efficiency and Renewable Energy (EERE), Meyer, P., Snowden-Swan, L. J., Padmaperuma, A. B., Tan, E., Dutta, A., Jacobson, J. J., & Cafferty, K. (2013) · OSTI OAI (U.S. Department of Energy Office of Scientific and Technical Information) · doi:10.2172/1126275 · Cited by 146
Xiong, Z., Guo, J., Chaiwat, W., Deng, W., Hu, X., Han, H., Chen, Y., Xu, K., Su, S., Hu, S., et al. (2020) · Fuel Processing Technology · doi:10.1016/j.fuproc.2019.106299 · Cited by 132
Recent developments in fast pyrolysis of ligno-cellulosic materials
Kersten, S. R. A., & Garcìa-Pèrez, M. (2013) · Current Opinion in Biotechnology · doi:10.1016/j.copbio.2013.04.003 · Cited by 140
Production and fuel properties of fast pyrolysis oil/bio-diesel blends
Garcìa-Pèrez, M., Shen, J. J., Wang, X. S., & Li, C. (2009) · Fuel Processing Technology · doi:10.1016/j.fuproc.2009.10.012 · Cited by 125
Self-citationHu, X., Guo, H., Gholizadeh, M., Sattari, B., & Liu, Q. (2019) · Biomass and Bioenergy · doi:10.1016/j.biombioe.2018.10.021 · Cited by 121
Liu, J., Hou, Q., Ju, M., Ji, P., Sun, Q., & Li, W. (2020) · Catalysts · doi:10.3390/catal10070742 · Cited by 109
“A higher reaction temperature can significantly reduce the amount of coke deposited, however, it may cause the polymerization of derived aromatic compounds [67].”
BackgroundPyrolysis of spent coffee grounds using a screw-conveyor reactor
Kelkar, S., Saffron, C. M., Chai, L., Bovee, J., Stuecken, T., Garedew, M., Li, Z., & Kriegel, R. M. (2015) · Fuel Processing Technology · doi:10.1016/j.fuproc.2015.04.006 · Cited by 115
“Lignin decomposition occurs over a wide temperature range and at a higher temperature than cellulose, contributing to the cellulose and hemicellulose decomposition peaks [42,43].”
BackgroundAbdullah, H., Mediaswanti, K. A., & Wu, H. (2010) · Energy & Fuels · doi:10.1021/ef901435f · Cited by 112
Fermentation of levoglucosan with oleaginous yeasts for lipid production
Lian, J., Garcìa-Pèrez, M., & Chen, S. (2013) · Bioresource Technology · doi:10.1016/j.biortech.2013.01.031 · Cited by 110
Selectivity of Bio-oils Catalytic Hydrotreatment Assessed by Petroleomic and GC*GC/MS-FID Analysis
Olcese, R. N., Carré, V., Aubriet, F., & Dufour, A. (2013) · Energy & Fuels · doi:10.1021/ef302145g · Cited by 108
Xue, Y., & Bai, X. (2018) · Energy Conversion and Management · doi:10.1016/j.enconman.2018.03.036 · Cited by 110
Formation of coke during the pyrolysis of bio-oil
Wang, Y., Mourant, D., Hu, X., Zhang, S., Lievens, C., & Li, C. (2012) · Fuel · doi:10.1016/j.fuel.2012.11.052 · Cited by 105
“Significant additional aromatic structures would have formed in addition to the aromatic structures inherently in lignin (mainly phenolic structures) [27].”
BackgroundSelf-citationLi, X., Gunawan, R., Lievens, C., Wang, Y., Mourant, D., Wang, X. S., Wu, H., Garcìa-Pèrez, M., & Li, C. (2011) · Fuel · doi:10.1016/j.fuel.2011.03.025 · Cited by 104
“% can be achieved at 450–500 C at high heating rates and with short residence time of the bio-oil vapour in hot zones [3–8].”
BackgroundMethodResultSelf-citationBio-oil from Sawdust: Effect of Operating Parameters on the Yield and Quality of Pyrolysis Products
Salehi, E., Abedi, J., & Harding, T. G. (2011) · Energy & Fuels · doi:10.1021/ef200688y · Cited by 104
Sustainable Electrochemical Depolymerization of Lignin in Reusable Ionic Liquids
Dier, T. K. F., Rauber, D., Durneata, D., Hempelmann, R., & Volmer, D. A. (2017) · Scientific Reports · doi:10.1038/s41598-017-05316-x · Cited by 103
Effect of ball milling on the hydrolysis of microcrystalline cellulose in hot‐compressed water
Yu, Y., & Wu, H. (2010) · AIChE Journal · doi:10.1002/aic.12288 · Cited by 103
Catalytic Upgrading of Biomass Fast Pyrolysis Vapors with Pd/SBA-15 Catalysts
Lu, Q., Tang, Z., Zhang, Y., & Zhu, X.-F. (2010) · Industrial & Engineering Chemistry Research · doi:10.1021/ie901198s · Cited by 96
The effect of pyrolysis temperature on recovery of bio-oil as distinctive stage fractions
Rover, M., Johnston, P. A., Whitmer, L. E., Smith, R. G., & Brown, R. C. (2013) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2013.11.012 · Cited by 97
Zhou, S., Pecha, M. B., van Kuppevelt, M., McDonald, A. G., & Garcìa-Pèrez, M. (2014) · Biomass and Bioenergy · doi:10.1016/j.biombioe.2014.03.064 · Cited by 94
“, Slow and fast pyr formation on the distribution of products, Biomass and Bioenerg [37] Garcia-Perez M, Wang S, Shen J, Rhodes M, Lee WJ, Li C-Z.”
Effect of the Fast Pyrolysis Temperature on the Primary and Secondary Products of Lignin
Zhou, S., Garcìa-Pèrez, M., Pecha, M. B., Kersten, S. R. A., McDonald, A. G., & Westerhof, R. J. M. (2013) · Energy & Fuels · doi:10.1021/ef4001677 · Cited by 102
Yu, Y., & Wu, H. (2010) · Energy & Fuels · doi:10.1021/ef9013746 · Cited by 92
Stepwise Fast Pyrolysis of Pine Wood
Westerhof, R. J. M., Brilman, D. W. F., Garcia-Perez, M., Wang, Z., Oudenhoven, S. R. G., & Kersten, S. R. A. (2012) · Energy & Fuels · doi:10.1021/ef301319t · Cited by 90
Luque, L., Westerhof, R. J. M., van Rossum, G., Oudenhoven, S. R. G., Kersten, S. R. A., Berruti, F., & Rehmann, L. (2014) · Bioresource Technology · doi:10.1016/j.biortech.2014.03.009 · Cited by 91
Zhou, S., Mourant, D., Lievens, C., Wang, Y., Li, C., & Garcìa-Pèrez, M. (2012) · Fuel · doi:10.1016/j.fuel.2012.06.010 · Cited by 91
“Because the UV-fluorescence is mainly associated with the lignin oligomers [47], the higher spectra recorded with oil obtained from the fluidized bed reactor is an indication of the higher content of lignin oligomers in these oils.”
BackgroundMethodResultSelf-citationMourant, D., Lievens, C., Gunawan, R., Wang, Y., Hu, X., Wu, L., Syed‐Hassan, S. S. A., & Li, C. (2012) · Fuel · doi:10.1016/j.fuel.2012.12.018 · Cited by 97
“These compounds are hydrophobic and comprise what is generally termed ‘‘pyrolytic lignin’’ [43,55–58].”
BackgroundMethodInfluentialSelf-citationLiaw, S., Zhou, S., Wu, H., & Garcìa-Pèrez, M. (2012) · Fuel · doi:10.1016/j.fuel.2012.08.016 · Cited by 97
“The properties of the feedstock [14], pyrolysis conditions [8,9], and particle size [13,15] are the three main factors affecting bio-oil quality.”
BackgroundMethodSelection of Temperature for Bio-oil Production from Pyrolysis of Algae from Lake Blooms
Li, R., Zhong, Z., Jin, B., & Zheng, A. (2012) · Energy & Fuels · doi:10.1021/ef300180r · Cited by 84
Impact of combined acid washing and acid impregnation on the pyrolysis of Douglas fir wood
Pecha, M. B., Arauzo, P. J., & Garcìa-Pèrez, M. (2015) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2015.05.014 · Cited by 83
Yu, Y., & Wu, H. (2009) · Industrial & Engineering Chemistry Research · doi:10.1021/ie900768m · Cited by 82
Chaiwat, W., Gunawan, R., Gholizadeh, M., Li, X., Lievens, C., Hu, X., Wang, Y., Mourant, D., Rossiter, A. J., Bromly, J., et al. (2013) · Fuel · doi:10.1016/j.fuel.2013.05.004 · Cited by 82
Self-citationInfluence of Pyrolysis Operating Conditions on Bio-Oil Components: A Microscale Study in a Pyroprobe
Thangalazhy-Gopakumar, S., Adhikari, S., Gupta, R. B., & Fernando, S. D. (2011) · Energy & Fuels · doi:10.1021/ef101032s · Cited by 81
Primaz, C. T., Schena, T., Lazzari, E., Caramão, E. B., & Jacques, R. A. (2018) · Fuel · doi:10.1016/j.fuel.2018.05.097 · Cited by 84
Effect of conditions on fast pyrolysis of bamboo lignin
Lou, R., Wu, S., & Lv, G. (2010) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2010.08.007 · Cited by 81
Liaw, S., Pérez, V. H., Zhou, S., Justo, O. R., & Garcìa-Pèrez, M. (2014) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2014.06.018 · Cited by 81
Gunawan, R., Li, X., Lievens, C., Gholizadeh, M., Chaiwat, W., Hu, X., Mourant, D., Bromly, J., & Li, C. (2013) · Fuel · doi:10.1016/j.fuel.2013.04.002 · Cited by 80
“Effects of (a) temperature (holding time: 3 h) and (b) reaction time description of the reactor system and experimental procedure can be found elsewhere [7].”
BackgroundSelf-citationAcid-catalysed reactions between methanol and the bio-oil from the fast pyrolysis of mallee bark
Hu, X., Gunawan, R., Mourant, D., Lievens, C., Li, X., Zhang, S., Chaiwat, W., & Li, C. (2012) · Fuel · doi:10.1016/j.fuel.2012.02.032 · Cited by 79
Self-citationLi, X., Gunawan, R., Wang, Y., Chaiwat, W., Hu, X., Gholizadeh, M., Mourant, D., Bromly, J., & Li, C. (2013) · Fuel · doi:10.1016/j.fuel.2013.08.046 · Cited by 78
Self-citationEffect of reaction conditions on hydrothermal degradation of cornstalk lignin
Ye, Y., Fan, J., & Chang, J. (2011) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2011.12.005 · Cited by 86
Cheng, S., Wei, L., Julson, J. L., Muthukumarappan, K., & Kharel, P. R. (2017) · Fuel Processing Technology · doi:10.1016/j.fuproc.2017.06.032 · Cited by 77
Coke formation during the hydrotreatment of bio-oil using NiMo and CoMo catalysts
Kadarwati, S., Hu, X., Gunawan, R., Westerhof, R. J. M., Gholizadeh, M., Hasan, M. M., & Li, C. (2016) · Fuel Processing Technology · doi:10.1016/j.fuproc.2016.08.021 · Cited by 75
“Pyrolysis is a process of decomposition of (macromolecular) materials thermally at high temperatures in the absence or shortage of oxygen [3, 26, 27].”
BackgroundMethodSelf-citationCompositional Changes during Hydrodeoxygenation of Biomass Pyrolysis Oil
Bi, Y., Wang, G., Shi, Q., Xu, C., & Gao, J. (2014) · Energy & Fuels · doi:10.1021/ef4024405 · Cited by 74
Wu, H., Yu, Y., & Yip, K. (2010) · Energy & Fuels · doi:10.1021/ef1008105 · Cited by 72
A Review on Lignin Liquefaction: Advanced Characterization of Structure and Microkinetic Modeling
Terrell, E., Dellon, L. D., Dufour, A., Bartolomei, E., Broadbelt, L. J., & Garcia-Perez, M. (2020) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.9b05744 · Cited by 71
Jia, L., Brech, Y. L., Shrestha, B. B., von Frowein, M. B., Ehlert, S., Mauviel, G., Zimmermann, R., & Dufour, A. (2015) · Energy & Fuels · doi:10.1021/acs.energyfuels.5b01803 · Cited by 70
Villadsen, S. R., Dithmer, L., Forsberg, R., Becker, J., Rudolf, A., Iversen, S. B., Iversen, B. B., & Glasius, M. (2012) · Energy & Fuels · doi:10.1021/ef300954e · Cited by 72
Abdullah, H., Mourant, D., Li, C., & Wu, H. (2010) · Energy & Fuels · doi:10.1021/ef1008117 · Cited by 67
Self-citationSecondary Vapor Phase Reactions of Lignin-Derived Oligomers Obtained by Fast Pyrolysis of Pine Wood
Zhou, S., Garcia-Perez, M., Pecha, B., McDonald, A. G., Kersten, S. R. A., & Westerhof, R. J. M. (2013) · Energy & Fuels · doi:10.1021/ef3019832 · Cited by 64
Yang, H.-M., Appari, S., Kudo, S., Hayashi, J., & Norinaga, K. (2015) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.5b01289 · Cited by 65
Douvartzides, S. L., Charisiou, N. D., Wang, W., Papadakis, V. G., Polychronopoulou, K., & Goula, M. A. (2021) · Renewable Energy · doi:10.1016/j.renene.2021.12.083 · Cited by 64
Catalytic fast pyrolysis for improved liquid quality
Banks, S. W., & Bridgwater, A. V. (2016) · Elsevier eBooks · doi:10.1016/b978-0-08-100455-5.00014-x · Cited by 76
Zhou, S., Wang, Z., Liaw, S., Li, C., & Garcìa-Pèrez, M. (2013) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2013.08.013 · Cited by 61
Self-citationMicro-explosion of liquid intermediates during the fast pyrolysis of sucrose and organosolv lignin
Montiel-Montoya, J., Pecha, M. B., Chejne, F., & Garcìa-Pèrez, M. (2016) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2016.10.010 · Cited by 59
Montiel-Montoya, J., Pecha, M. B., Roman, D. T., Chejne, F., & Garcìa-Pèrez, M. (2016) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2016.11.008 · Cited by 61
Kadarwati, S., Oudenhoven, S. R. G., Schagen, M., Hu, X., Garcìa-Pèrez, M., Kersten, S. R. A., Li, C., & Westerhof, R. J. M. (2016) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2016.01.011 · Cited by 58
Self-citationHu, X., Lievens, C., Mourant, D., Wang, Y., Wu, L., Gunawan, R., Song, Y., & Li, C. (2013) · Applied Energy · doi:10.1016/j.apenergy.2013.04.078 · Cited by 57
“50% of the compounds in bio-oil [26].”
BackgroundSelf-citationKekäläinen, T., Venäläinen, T., & Jänis, J. (2014) · Energy & Fuels · doi:10.1021/ef500849z · Cited by 62
Xiong, Z., Han, H., Azis, M. M., Hu, X., Wang, Y., Su, S., Hu, S., & Xiang, J. H. (2018) · Fuel · doi:10.1016/j.fuel.2018.10.151 · Cited by 57
Naron, D. R., Collard, F.-X., Tyhoda, L., & Görgens, J. F. (2019) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2018.12.015 · Cited by 54
Understanding the product distribution from biomass fast pyrolysis
Patwardhan, P. R. (2018) · doi:10.31274/etd-180810-1964 · Cited by 57
Thermal decomposition of pyrolytic lignin under inert conditions at low temperatures
Chua, Y. W., Yu, Y., & Wu, H. (2017) · Fuel · doi:10.1016/j.fuel.2017.03.035 · Cited by 56
Identifying the primary reactions and products of fast pyrolysis of alkali lignin
Supriyanto, Usino, D. O., Ylitervo, P., Dou, J., Sipponen, M. H., & Richards, T. (2020) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2020.104917 · Cited by 54
Methods and Challenges in the Determination of Molecular Weight Metrics of Bio-oils
Harman-Ware, A. E., & Ferrell, J. R. (2018) · Energy & Fuels · doi:10.1021/acs.energyfuels.8b02113 · Cited by 54
TG-FTIR Method for the Characterization of Bio-oils in Chemical Families
Stankovikj, F., & Garcìa-Pèrez, M. (2017) · Energy & Fuels · doi:10.1021/acs.energyfuels.6b03132 · Cited by 58
Eucalypts as a biofuel feedstock
Shepherd, M., Bartle, J., Lee, D. J., Brawner, J. T., Bush, D., Turnbull, P., Macdonell, P., Brown, T. R., Simmons, B. A., & Henry, R. J. (2011) · Biofuels · doi:10.4155/bfs.11.136 · Cited by 59
Saraeian, A., Aui, A., Gao, Y., Wright, M. M., Foston, M. B., & Shanks, B. H. (2020) · Green Chemistry · doi:10.1039/c9gc04245h · Cited by 52
Singh, S., Bhaumik, S. K., Dong, L., Li, C., & Vuthaluru, H. B. (2021) · Fuel · doi:10.1016/j.fuel.2021.121935 · Cited by 51
Self-citationZhou, S., Osman, N. B., Li, H., McDonald, A. G., Mourant, D., Li, C., & Garcìa-Pèrez, M. (2012) · Fuel · doi:10.1016/j.fuel.2012.07.052 · Cited by 51
“Pyrolytic lignin (PL) was separated from the bio-oils according to a method described elsewhere [4].”
BackgroundMethodSelf-citationOudenhoven, S. R. G., Lievens, C., Westerhof, R. J. M., & Kersten, S. R. A. (2015) · Biomass and Bioenergy · doi:10.1016/j.biombioe.2015.12.019 · Cited by 49
EPR detection of key radicals during coking process of lignin monomer pyrolysis
Zhou, Q., Luo, Z., Li, G., & Li, S. (2020) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2020.104948 · Cited by 49
Metadata
- Authors
- Garcia-Perez, M., Wang, S., Shen, J., Rhodes, M., Lee, W. J., & Li, C.-Z.
- Affiliations
- Department of Chemical Engineering, PO Box 36, Monash University, Victoria 3800, Australia; Biological Systems Engineering Department, Washington State University, Pullman, Washington 99164; and Department of Chemical Engineering, Taiyuan University of Technology, Shanxi 030024, P. R. China
- Monash University (AU)
- Corresponding author
- Li, Chun-Zhu
- Venue
- Energy & Fuels
- Publisher
- American Chemical Society (ACS)
- Published
- 2008-03-22
- Volume
- 22
- Issue
- 3
- Pages
- 2022-2032
- ISSN
- 0887-0624 (ISSN-L)
- 1520-5029
- OpenAlex
- W1980687513
- Cited by
- 235
- References
- 34
- Citations by year
- 2025: 7 · 2024: 6 · 2023: 7 · 2022: 6 · 2021: 13 · 2020: 15 · 2019: 10 · 2018: 12 · 2017: 19 · 2016: 24 · 2015: 13 · 2014: 16 · 2013: 23 · 2012: 21
- FWCI
- 9.50
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- Energy & Fuels (publishedVersion)
- eSpace (Curtin University) (submittedVersion)
- Topics
- Physical Sciences › Energy › Fuel Technology › Thermochemical Biomass Conversion Processes
- Physical Sciences › Energy › Fuel Technology › Mining and Gasification Technologies
- Physical Sciences › Chemical Engineering › Fluid Flow and Transfer Processes › Advanced Combustion Engine Technologies
- Keywords
- fast pyrolysis, bio-oil composition, pyrolysis temperature, bio-oil yield, volatile compounds, heavy components
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.