The DOI matches its Crossref record; 24 of the 24 references it cites were found in a registry or an index.
Thermogravimetric Analysis and Devolatilization Kinetics of Wood
Abstract
Thermogravimetric curves have been measured at a heating rate of 5 K/min for several hardwoods (beech, alder, birch, and oak) and softwoods (Douglas fir, two pine species, redwood, and spruce), whose chemical composition varies within the usual standards. The analysis of the devolatilization characteristics is based on the introduction of several reaction temperatures. A comparison between hardwoods and softwoods shows that, in the latter case, the decomposition starts at lower temperatures, the hemicellulose shoulder is more delayed, and both the hemicellulose and cellulose zones are wider. Furthermore, the yields of char are higher. However, a devolatilization mechanism, consisting of three parallel reactions and the same set of activation energies for hemicellulose, cellulose, and lignin (100, 236, and 46 kJ/mol), can describe the high-temperature (>553 K) degradation behavior of all of the woods with a good accuracy. Modifications for the extension of the mechanism at lower temperatures are required only for species with significant extractive contents and consist of two further reactions (activation energies of 105 and 127 kJ/mol, respectively).
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Combustion of agricultural residues
Werther, J., Saenger, M., Hartge, E.-U., Ogada, T., & Siagi, Z. (2000) · Progress in Energy and Combustion Science · doi:10.1016/s0360-1285(99)00005-2 · Cited by 1,123
Cellulose Pyrolysis Kinetics: The Current State of Knowledge
Antal, M. J. J., & Varhegyi, G. (1995) · Industrial & Engineering Chemistry Research · doi:10.1021/ie00042a001 · Cited by 859
Co-firing of coal and biomass fuel blends
Sami, M., Annamalai, K., & Wooldridge, M. (2001) · Progress in Energy and Combustion Science · doi:10.1016/s0360-1285(00)00020-4 · Cited by 838
Progress in Thermochemical Biomass Conversion
(2001) · Wiley eBooks · doi:10.1002/9780470694954 · Cited by 552
Kinetic modeling of biomass pyrolysis
Várhegyi, G., Antal, M. J., Jakab, E., & Szabó, P. (1997) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/s0165-2370(96)00971-0 · Cited by 545
Self-citationAdvances in Thermochemical Biomass Conversion
(1993) · Springer eBooks · doi:10.1007/978-94-011-1336-6 · Cited by 540
Pyrolysis characteristics and kinetics of municipal solid wastes
Sørum, L., Grønli, M. G., & Hustad, J. E. (2001) · Fuel · doi:10.1016/s0016-2361(00)00218-0 · Cited by 527
Self-citationModeling and simulation of combustion processes of charring and non-charring solid fuels
Di Blasi, C. (1993) · Progress in Energy and Combustion Science · doi:10.1016/0360-1285(93)90022-7 · Cited by 494
Self-citationDynamic behaviour of stratified downdraft gasifiers
Blasi, C. D. (2000) · Chemical Engineering Science · doi:10.1016/s0009-2509(99)00562-x · Cited by 355
Cellulose Pyrolysis Kinetics: Revisited
Antal, M. J., Várhegyi, G., & Jakab, E. (1998) · Industrial & Engineering Chemistry Research · doi:10.1021/ie970144v · Cited by 323
Self-citation
Cited by
Libra, J. A., Ro, K. S., Kammann, C., Funke, A., Berge, N. D., Neubauer, Y., Titirici, M.-M., Fühner, C., Bens, O., Kern, J., et al. (2011) · Biofuels · doi:10.4155/bfs.10.81 · Cited by 1,756
Modeling chemical and physical processes of wood and biomass pyrolysis
DIBLASI, C. (2008) · Progress in Energy and Combustion Science · doi:10.1016/j.pecs.2006.12.001 · Cited by 1,752
Kambo, H. S., & Dutta, A. (2015) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2015.01.050 · Cited by 1,746
Biofuels Production through Biomass Pyrolysis—A Technological Review
Jahirul, M., Rasul, M., Chowdhury, A., & Ashwath, N. (2012) · Energies · doi:10.3390/en5124952 · Cited by 1,427
Thermogravimetric analysis and kinetic study of poplar wood pyrolysis
Slopiecka, K., Bartocci, P., & Fantozzi, F. (2012) · Applied Energy · doi:10.1016/j.apenergy.2011.12.056 · Cited by 831
Kim, K. H., Kim, J.-Y., Cho, T.-S., & Choi, J. W. (2012) · Bioresource Technology · doi:10.1016/j.biortech.2012.04.094 · Cited by 696
Insights into Biochar and Hydrochar Production and Applications: A Review
Zhang, Z., Zhu, Z., Shen, B., & Liu, L. (2019) · Energy · doi:10.1016/j.energy.2019.01.035 · Cited by 687
Biomass pyrolysis-a review of modelling, process parameters and catalytic studies
Sharma, A., Pareek, V., & Zhang, D. (2015) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2015.04.193 · Cited by 675
Al-Rumaihi, A., Shahbaz, M., Mckay, G., Mackey, H., & Al-Ansari, T. (2022) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2022.112715 · Cited by 650
Burhenne, L., Messmer, J., Aicher, T., & Laborie, M.-P. (2013) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2013.01.012 · Cited by 615
Pariyar, P., Kumari, K., Jain, M. K., & Jadhao, P. S. (2020) · Science of The Total Environment · doi:10.1016/j.scitotenv.2019.136433 · Cited by 454
Escalante, J., Chen, W.-H., Tabatabaei, M., Hoang, A. T., Kwon, E. E., Andrew Lin, K.-Y., & Saravanakumar, A. (2022) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2022.112914 · Cited by 414
Ghodake, G. S., Shinde, S. K., Kadam, A. A., Saratale, R. G., Saratale, G. D., Kumar, M., Palem, R. R., AL-Shwaiman, H. A., Elgorban, A. M., Syed, A., et al. (2021) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2021.126645 · Cited by 414
Thermogravimetric–mass spectrometric analysis of lignocellulosic and marine biomass pyrolysis
Sanchez-Silva, L., López-González, D., Villaseñor, J., Sánchez, P., & Valverde, J. L. (2012) · Bioresource Technology · doi:10.1016/j.biortech.2012.01.001 · Cited by 406
GC/MS Characterization of Liquids Generated from Low-Temperature Pyrolysis of Wood
Branca, C., Giudicianni, P., & Di Blasi, C. (2003) · Industrial & Engineering Chemistry Research · doi:10.1021/ie030066d · Cited by 405
Self-citationDetailed kinetic modeling of the thermal degradation of lignins
Faravelli, T., Frassoldati, A., Migliavacca, G., & Ranzi, E. (2010) · Biomass and Bioenergy · doi:10.1016/j.biombioe.2009.10.018 · Cited by 376
Chen, Z., Hu, M., Zhu, X., Guo, D., Liu, S., Hu, Z., Xiao, B., Wang, J., & Laghari, M. (2015) · Bioresource Technology · doi:10.1016/j.biortech.2015.05.062 · Cited by 361
A comparative kinetic study on the pyrolysis of three different wood species
Müller-Hagedorn, M., Bockhorn, H., Krebs, L., & Müller, U. (2003) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/s0165-2370(03)00065-2 · Cited by 337
Thermal decomposition of wood: Kinetics and degradation mechanisms
Poletto, M., Zattera, A. J., & Santana, R. M. C. (2012) · Bioresource Technology · doi:10.1016/j.biortech.2012.08.133 · Cited by 331
Kambo, H. S., & Dutta, A. (2015) · Energy Conversion and Management · doi:10.1016/j.enconman.2015.08.031 · Cited by 302
Biomass pyrolysis technologies for value-added products: a state-of-the-art review
Amenaghawon, A. N., Anyalewechi, C. L., Okieimen, C. O., & Kusuma, H. S. (2021) · Environment, Development and Sustainability · doi:10.1007/s10668-021-01276-5 · Cited by 260
How to determine consistent biomass pyrolysis kinetics in a parallel reaction scheme
Anca-Couce, A., Berger, A., & Zobel, N. (2014) · Fuel · doi:10.1016/j.fuel.2014.01.014 · Cited by 229
Ding, Y., Zhang, W., Yu, L., & Lu, K. (2019) · Energy · doi:10.1016/j.energy.2019.04.030 · Cited by 220
Várhegyi, G., Grønli, M. G., & Di Blasi, C. (2004) · Industrial & Engineering Chemistry Research · doi:10.1021/ie034168f · Cited by 115
Self-citationOkaikue-Woodi, F. E. K., Cherukumilli, K., & Ray, J. R. (2020) · Water Research · doi:10.1016/j.watres.2020.116434 · Cited by 100
Fast pyrolysis of lignins with different molecular weight: Experiments and modelling
Marathe, P. S., Westerhof, R. J. M., & Kersten, S. R. A. (2019) · Applied Energy · doi:10.1016/j.apenergy.2018.12.058 · Cited by 71
Pyrolysis of furniture wood waste: Decomposition and gases evolved
Moreno, A. I., & Font, R. (2015) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2015.03.008 · Cited by 63
Kinetics of the pyrolytic and hydrothermal decomposition of water hyacinth
Luo, G., James Strong, P., Wang, H., Ni, W., & Shi, W. (2011) · Bioresource Technology · doi:10.1016/j.biortech.2011.04.048 · Cited by 56
Yu, H., Liu, F., Ke, M., & Zhang, X. (2015) · Bioresource Technology · doi:10.1016/j.biortech.2015.03.005 · Cited by 38
Samuelsson, L. N., Babler, M. U., & Moriana, R. (2015) · Fuel · doi:10.1016/j.fuel.2015.08.019 · Cited by 29
Paul, S., Dutta, A., & Defersha, F. (2018) · Energy · doi:10.1016/j.energy.2018.09.182 · Cited by 23
Andrade, P. I., Araújo, S. D. O., Neiva, D. M., Vital, B. R., Oliveira Carneiro, A. D. C., Gominho, J., & Pereira, H. (2016) · Holzforschung · doi:10.1515/hf-2015-0090 · Cited by 16
Preimesberger, C., Wondrak, M., Solt-Rindler, A., Pfeifer, C., & Hansmann, C. (2024) · Biomass Conversion and Biorefinery · doi:10.1007/s13399-023-03977-5 · Cited by 6
“The higher thermal stability of spruce might also be caused by more stable variants of cellulose and lignin in softwood species [40, 41].”
Metadata
- Authors
- Grønli, M. G., Várhegyi, G., & Di Blasi, C.
- Venue
- Industrial & Engineering Chemistry Research
- Publisher
- American Chemical Society (ACS)
- Published
- 2002-07-27
- Volume
- 41
- Issue
- 17
- Pages
- 4201-4208
- ISSN
- 0888-5885 (ISSN-L)
- 1520-5045
- OpenAlex
- W2044171595
- Cited by
- 818
- References
- 24
- FWCI
- 5.46
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.