Network Stretching, Slip Processes, and Fragmentation of Crystallites during Uniaxial Drawing of Polyethylene and Related Copolymers. A Comparative Study
The DOI matches its Crossref record; 33 of the 33 references it cites were found in a registry or an index.
Abstract
When polyethylene (PE) is deformed to large strains, the stress originates from both the viscous forces associated with the plastic deformation of the crystallites by slip and fragmentation processes and the entropic elastic forces arising from the stretching of the entangled amorphous regions. Relative weights of the different processes change with the crystallinity. The dependencies were analyzed in a comprehensive study on a series of samples encompassing a large range of crystallinities: PE, low-density PE (LDPE), and ethylene−vinylacetate copolymers. The comparison was based on measured true stress−strain curves for constant strain rates. For the samples with higher crystallinity, which show a necking, this was achieved by employing a video-controlled tensile testing machine. Recovery properties of the sample were studied in step-cycle runs, where the load was applied stepwise and interrupted after each step by an unloading−reloading loop. Simultaneous with the mechanical testing, the related texture changes were determined by a measurement of the WAXS patterns. In spite of the large changes in the gross mechanical properties from solid- to rubberlike, there exists a common general scheme for the deformation behavior. For all samples, one finds four characteristic points where the differential compliance changes. They may be associated with (1) the onset of isolated slip processes, (2) a change into a collective activity of the slips, (3) the beginning of crystallite fragmentation, and (4) chain disentanglement resulting in a finite truly irreversible deformation. When the crystallinity is increased, the stresses at the four transition points also increase. The related strains, however, remain essentially constant. Crystal textures are also a function of the imposed strain only, the dependencies being common for all samples. Experiments support the novel picture of a granular substructure of the crystalline lamellae as a basic structural feature. Block slips with the three surfaces as slip planes enable the system to easily react on each imposed strain in a well-defined way.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“The curve for X-direction elongation in figure 2 has the same typical shape as those obtained from laboratory experiments on PE, for instance the experiments using strain rates between 10-4 and 10-2 s-1 performed by Hiss et al [17] and Addiego et al [18].”
In the citing paper
“Hiss et al [17] and Addiego et al [18] also found that increasing strain rate increases the yield stress.”
In the citing paper
“Moreover, the curve of virgin PE agrees quite well with the true stress-true strain curves obtained in tensile deformation mode for polyethylene of similar molecular characteristics [4,45].”
From Erosion of the molecular network in the amorphous layers of polyethylene upon high-strain deformation (2016) · cites this paper as [4]
In the citing paper
“This transition was postulated to be a result of intensified crystal fragmentation and presumably chain disentanglement beginning in amorphous phase that should lead to a partial disintegration of the molecular network [4].”
From Erosion of the molecular network in the amorphous layers of polyethylene upon high-strain deformation (2016) · cites this paper as [4]
In the citing paper
“The same is actually true for semicrystalline polymers, since their deformation can be considered as a simultaneous deformation of two co-continuous interlaced network-like structures: a skeleton made up of crystallites interconnected with the interlamellar layers of entangled amorphous phase [4]”
From Erosion of the molecular network in the amorphous layers of polyethylene upon high-strain deformation (2016) · cites this paper as [4]
3 more claims about this paper
Create a free account to see every claim other papers make about this one.
Citations
Cites
Strobl, G. R. (1996) · Springer eBooks · doi:10.1007/978-3-662-03243-5 · Cited by 1,497
Self-citationMolecular model of drawing polyethylene and polypropylene
Peterlin, A. (1971) · Journal of Materials Science · doi:10.1007/bf00550305 · Cited by 987
The use of a mathematical model to describe isothermal stress-strain curves in glassy thermoplastics
Haward, R. N., & Thackray, G. (1968) · Proceedings of the Royal Society of London. Series A. Mathematical and Physical Sciences · doi:10.1098/rspa.1968.0029 · Cited by 646
Deformation mechanisms in crystalline polymers
Bowden, P. B., & Young, R. J. (1974) · Journal of Materials Science · doi:10.1007/bf00540553 · Cited by 551
Determination of the plastic behaviour of solid polymers at constant true strain rate
G'sell, C., & Jonas, J. J. (1979) · Journal of Materials Science · doi:10.1007/bf00772717 · Cited by 439
Strain hardening of thermoplastics
Haward, R. N. (1993) · Macromolecules · doi:10.1021/ma00074a006 · Cited by 326
The necking and cold-drawing of rigid plastics
Vincent, P. I. (1960) · Polymer · doi:10.1016/0032-3861(60)90003-3 · Cited by 320
Video-controlled tensile testing of polymers and metals beyond the necking point
G'Sell, C., Hiver, J. M., Dahoun, A., & Souahi, A. (1992) · Journal of Materials Science · doi:10.1007/bf01105270 · Cited by 299
Phase Transformation and Deformation Processes in Oriented Polyethylene
Seto, T., Hara, T., & Tanaka, K. (1968) · Japanese Journal of Applied Physics · doi:10.1143/jjap.7.31 · Cited by 266
Polymer deformation in terms of spherulites
Hay, I. L., & Keller, A. (1965) · Kolloid-Zeitschrift & Zeitschrift für Polymere · doi:10.1007/bf01500379 · Cited by 255
Research works printed but not linked: 7
- Haward R., 1968, Proc. R. Soc. A, 302, 453
- Takahashi Y., 1988, Part B: Polym. Phys
- Bridgman P., 1944, Trans. Am. Soc. Met., 32, 553
- Hiss, R. Ph.D. Thesis, Freiburg, 1996.
- Gauthier C., 10th International Conference on Deformation, Yield and Fracture of Polymers; Institute of Materials: London
- Krigas T., 1985, J. Polym. Sci., 23, 509
- Kelly A., 1970, Crystallography of Crystal Defects
Cited by
Items 101–200 of 545
Sakurai, T., Nozue, Y., Kasahara, T., Mizunuma, K., Yamaguchi, N., Tashiro, K., & Amemiya, Y. (2005) · Polymer · doi:10.1016/j.polymer.2005.01.106 · Cited by 52
Rate‐, temperature‐, and structure‐dependent yield kinetics of isotactic polypropylene
van Erp, T. B., Cavallo, D., Peters, G. G., & Govaert, L. E. (2012) · Journal of Polymer Science Part B Polymer Physics · doi:10.1002/polb.23150 · Cited by 51
Liu, G., Zheng, L., Zhang, X., Li, C., & Wang, D. (2014) · Macromolecules · doi:10.1021/ma501832z · Cited by 51
Bartczak, Z. (2005) · Polymer · doi:10.1016/j.polymer.2005.07.096 · Cited by 50
Pepels, M. P. F., Govaert, L. E., & Duchateau, R. (2015) · Macromolecules · doi:10.1021/acs.macromol.5b01089 · Cited by 51
Molecular Alignment in Polyethylene during Cold Drawing Using In-Situ SANS and Raman Spectroscopy
López-Barrón, C. R., Zeng, Y., Schaefer, J. J., Eberle, A. P. R., Lodge, T. P., & Bates, F. S. (2017) · Macromolecules · doi:10.1021/acs.macromol.7b00504 · Cited by 50
Zhou, J., Zheng, Y., Shan, G., Bao, Y., Wang, W.-J., & Pan, P. (2020) · Polymer · doi:10.1016/j.polymer.2019.122121 · Cited by 50
Drozdov, A. D., & Christiansen, J. D. C. (2006) · Computational Materials Science · doi:10.1016/j.commatsci.2006.09.001 · Cited by 51
Structural evolution of β – iPP during uniaxial stretching studied by in–situ WAXS and SAXS
Zhang, C., Liu, G., Song, Y., Zhao, Y., & Wang, D. (2014) · Polymer · doi:10.1016/j.polymer.2014.10.049 · Cited by 49
Wang, Z., Xia, Z., Yu, Z., Chen, E., Sue, H., Han, C. C.-C., & Hsiao, B. S. (2006) · Macromolecules · doi:10.1021/ma051928k · Cited by 49
Cavitation phenomenon and mechanical properties of partially disentangled polypropylene
Pawlak, A., Krajenta, J., & Gałęski, A. (2018) · Polymer · doi:10.1016/j.polymer.2018.07.033 · Cited by 50
Tanaka, M., & Young, R. J. (2006) · Macromolecules · doi:10.1021/ma0526286 · Cited by 48
Chevron morphology in deformed semicrystalline polymers
Krumova, M., Henning, S., & Michler, G. H. (2006) · The Philosophical Magazine A Journal of Theoretical Experimental and Applied Physics · doi:10.1080/14786430500501671 · Cited by 48
Rosa, C. D., Auriemma, F., de Ballesteros, O. R., Iacono, S. D., Luca, D. D., & Resconi, L. (2008) · Crystal Growth & Design · doi:10.1021/cg800102f · Cited by 48
Zhu, P. W., & Edward, G. H. (2008) · Journal of Materials Science · doi:10.1007/s10853-008-2979-1 · Cited by 47
Yang, P., Song, Y., Feng, W., & Zhang, W. (2018) · Macromolecules · doi:10.1021/acs.macromol.8b01544 · Cited by 47
Step-Cycle Mechanical Processing of Gels of sPP-b-EPR-b-sPP Triblock Copolymer in Mineral Oil
Wang, Z., Niu, Y., Fredrickson, G. H., Krämer, E. J., Shin, Y.-W., Shimizu, F., Zuo, F., Rong, L., Hsiao, B. S., & Coates, G. W. (2010) · Macromolecules · doi:10.1021/ma1011842 · Cited by 50
Viscous-Force-Dominated Tensile Deformation Behavior of Oriented Polyethylene
Na, B., Zhang, Q., Fu, Q., Men, Y., Hong, K., & Strobl, G. R. (2006) · Macromolecules · doi:10.1021/ma052496g · Cited by 47
Self-citationMao, Y., Li, X., Burger, C. P., Hsiao, B. S., & Tsou, A. H. (2012) · Polymer · doi:10.1016/j.polymer.2012.12.037 · Cited by 46
Cavitation during Drawing of Crystalline Polymers
Gałęski, A., & Różański, A. (2010) · Macromolecular Symposia · doi:10.1002/masy.201000076 · Cited by 46
Che, J., Locker, C. R., Lee, S., Rutledge, G. C., Hsiao, B. S., & Tsou, A. H. (2013) · Macromolecules · doi:10.1021/ma4005007 · Cited by 46
Deplace, F., Scholz, A. K., Fredrickson, G. H., Krämer, E. J., Shin, Y.-W., Shimizu, F., Zuo, F., Rong, L., Hsiao, B. S., & Coates, G. W. (2012) · Macromolecules · doi:10.1021/ma300808n · Cited by 49
Litvinov, V. M., Persyn, O., Gaucher, V., & Lefebvre, J. (2010) · Macromolecules · doi:10.1021/ma1014403 · Cited by 45
Structural Evolution of Ethylene–Octene Copolymers upon Stretching and Unloading
Sun, Y., Fu, L., Wu, Z., & Men, Y. (2013) · Macromolecules · doi:10.1021/ma3020933 · Cited by 45
Auriemma, F., Rosa, C. D., Girolamo, R. D., Malafronte, A., Scoti, M., Mitchell, G. R., & Esposito, S. (2017) · Macromolecules · doi:10.1021/acs.macromol.7b00045 · Cited by 45
The Influence of Chemical Structure on Polyolefin Melt Rheology and Miscibility
Lohse, D. J. (2005) · Journal of macromolecular science. Part C, Reviews in macromolecular chemistry and physics/Journal of macromolecular science. Reviews in macromolecular chemistry and physics · doi:10.1080/15321790500304098 · Cited by 49
“It is known that some mechanical properties, such as yield stress (51) and tensile performance (52) can be related to entanglement.”
BackgroundOn the application of FEM to deformation of high-density polyethylene
Kwon, H., & Jar, P. ‐. B. (2008) · International Journal of Solids and Structures · doi:10.1016/j.ijsolstr.2008.02.013 · Cited by 51
Cyclic viscoplasticity of semicrystalline polymers with finite deformations
Drozdov, A. D., Klitkou, R., & Christiansen, J. D. C. (2012) · Mechanics of Materials · doi:10.1016/j.mechmat.2012.09.005 · Cited by 44
Stretching Temperature Dependency of Fibrillation Process in Isotactic Polypropylene
Lu, Y., Chen, R., Zhao, J., Jiang, Z., & Men, Y. (2017) · The Journal of Physical Chemistry B · doi:10.1021/acs.jpcb.7b05071 · Cited by 44
Kida, T., Hiejima, Y., & Nitta, K. (2019) · Macromolecules · doi:10.1021/acs.macromol.8b02740 · Cited by 44
Elastic properties of polyethylene from high pressure sound speed measurements
Jordan, J. L., Rowland, R. L., Greenhall, J., Moss, E. K., Huber, R. C., Willis, E., Hrubiak, R., Kenney‐Benson, C., Bartram, B. D., & Sturtevant, B. T. (2020) · Polymer · doi:10.1016/j.polymer.2020.123164 · Cited by 46
A molar mass induced transition in the yielding properties of linear polyethylene
Fu, Q., Men, Y., & Strobl, G. R. (2003) · Polymer · doi:10.1016/s0032-3861(03)00036-3 · Cited by 44
Self-citationConstitutive equations in finite viscoplasticity of semicrystalline polymers
Drozdov, A. D., & Gupta, R. K. (2003) · International Journal of Solids and Structures · doi:10.1016/s0020-7683(03)00414-1 · Cited by 44
Frick, A., Sich, D., Heinrich, G., Stern, C., Gössi, M., & Tervoort, T. A. (2012) · Macromolecular Materials and Engineering · doi:10.1002/mame.201200172 · Cited by 43
Stress–strain behavior of cold-drawn isotactic polypropylene subjected to various drawn histories
Nitta, K., & Nomura, H. (2014) · Polymer · doi:10.1016/j.polymer.2014.10.028 · Cited by 44
Evidence for a mechanically active high temperature relaxation process in syndiotactic polypropylene
Men, Y., & Strobl, G. R. (2002) · Polymer · doi:10.1016/s0032-3861(02)00082-4 · Cited by 43
Self-citationLi, D. S., Garmestani, H., Alamo, R. G., & Kalidindi, S. R. (2003) · Polymer · doi:10.1016/s0032-3861(03)00527-5 · Cited by 45
Deplace, F., Wang, Z., Lynd, N. A., Hotta, A., Rose, J. M., Hustad, P. D., Tian, J., Ohtaki, H., Coates, G. W., Shimizu, F., et al. (2010) · Journal of Polymer Science Part B Polymer Physics · doi:10.1002/polb.21969 · Cited by 43
Molecular Orientations and True Stress−Strain Relationship in Isotactic Polypropylene Film
Song, Y., Nitta, K., & Nemoto, N. (2003) · Macromolecules · doi:10.1021/ma030194d · Cited by 44
Zhang, W., Wang, Y., & Wu, D. (2022) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2022.119372 · Cited by 42
Failure of elastic‐plastic core–shell microcapsules under compression
Mercadé‐Prieto, R., Allen, R., Zhang, Z., York, D. W., Preece, J. A., & Goodwin, T. E. (2011) · AIChE Journal · doi:10.1002/aic.12804 · Cited by 42
Chen, H. Y., Chum, S. P., Hiltner, A., & Baer, E. (2001) · Journal of Polymer Science Part B Polymer Physics · doi:10.1002/polb.1130 · Cited by 42
Critical stress for drawing-induced α crystal–mesophase transition in isotactic polypropylene
Ma, Z., Shao, C., Wang, X. L., Zhao, B., Li, X., An, H., Yan, T., Li, Z., & Li, L. (2009) · Polymer · doi:10.1016/j.polymer.2009.04.010 · Cited by 41
Zhao, J., Sun, Y., & Men, Y. (2016) · Macromolecules · doi:10.1021/acs.macromol.5b02585 · Cited by 41
Chang, B., Schneider, K., Vogel, R., & Heinrich, G. (2018) · Polymer · doi:10.1016/j.polymer.2018.01.081 · Cited by 41
Wang, C., & Weiss, R. G. (2003) · Macromolecules · doi:10.1021/ma025797o · Cited by 41
Polyolefin thermoplastic elastomers from 1-octene copolymerization with 1-decene and cyclopentene
Pierro, I., Leone, G., Zanchin, G., Canetti, M., Ricci, G., & Bertini, F. (2017) · European Polymer Journal · doi:10.1016/j.eurpolymj.2017.05.044 · Cited by 40
Lu, Y., & Men, Y. (2018) · Chinese Journal of Polymer Science · doi:10.1007/s10118-018-2123-x · Cited by 40
Xiong, B., Lame, O., Chenal, J., Men, Y., Séguéla, R., & Vigier, G. (2017) · Polymer · doi:10.1016/j.polymer.2017.05.011 · Cited by 39
Kida, T., Hiejima, Y., & Nitta, K. (2020) · Macromolecules · doi:10.1021/acs.macromol.0c02124 · Cited by 40
Deformation and failure of semicrystalline polymers under dynamic tensile and biaxial impact loading
Torres, J. P., Frontini, P. M., Machado, M. D. S. C., & Major, Z. (2016) · International Journal of Impact Engineering · doi:10.1016/j.ijimpeng.2016.08.004 · Cited by 39
Zhang, W., Qi, Y., Ye, K., Zhang, Q., Chen, W., Meng, L., Chen, X., Wang, D., & Li, L. (2018) · Polymer · doi:10.1016/j.polymer.2018.12.029 · Cited by 39
WAXS/SAXS study of plastic deformation instabilities and lamellae fragmentation in polyethylene
Bartczak, Z., & Vozniak, A. (2019) · Polymer · doi:10.1016/j.polymer.2019.05.076 · Cited by 38
Sun, C., Xu, S., Zhou, J., Ni, L., Xia, J., Bao, Y., Shan, G., & Pan, P. (2023) · Macromolecules · doi:10.1021/acs.macromol.3c00494 · Cited by 38
Raabe, D., Chen, N., & Chen, L. (2004) · Polymer · doi:10.1016/j.polymer.2004.09.045 · Cited by 38
Makarewicz, C., Safandowska, M., Idczak, R., & Różański, A. (2021) · Macromolecules · doi:10.1021/acs.macromol.1c01258 · Cited by 37
Lezak, E., & Bartczak, Z. (2007) · Journal of Polymer Science Part B Polymer Physics · doi:10.1002/polb.21345 · Cited by 37
Tanabe, T., Watanabe, K., Oyama, Y., & Seo, K. (2010) · NDT & E International · doi:10.1016/j.ndteint.2010.03.001 · Cited by 36
Jia, J., & Raabe, D. (2006) · European Polymer Journal · doi:10.1016/j.eurpolymj.2006.02.013 · Cited by 36
Dong, X., McDowell, D. L., Kalidindi, S. R., & Jacob, K. I. (2014) · Polymer · doi:10.1016/j.polymer.2014.03.045 · Cited by 36
Phase transition behavior and deformation mechanism of polytetrafluoroethylene under stretching
Luo, C., Pei, J., Zhuo, W., Niu, Y., & Li, G. (2021) · RSC Advances · doi:10.1039/d1ra06333b · Cited by 35
“24,31 Actually, the sample is usually non-uniformly deformed under certain stretching conditions.”
Jiang, C., Chao, Y., Xie, W., & Wu, D. (2024) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2024.130178 · Cited by 35
Farge, L., André, S., Pawlak, A., Baravian, C., Irvine, S. C., & Philippe, A. (2013) · Journal of Polymer Science Part B Polymer Physics · doi:10.1002/polb.23267 · Cited by 35
Muliana, A. H., Rajagopal, K. R., Tscharnuter, D., & Pinter, G. (2016) · International Journal of Solids and Structures · doi:10.1016/j.ijsolstr.2016.07.017 · Cited by 35
Liao, T., Yang, X. G., Zhao, X., Tang, Y., Jiang, Z., & Men, Y. (2021) · Macromolecules · doi:10.1021/acs.macromol.1c00944 · Cited by 35
Liu, G., Schneider, K., Zheng, L., Zhang, X., Li, C., Stamm, M., & Wang, D. (2014) · Polymer · doi:10.1016/j.polymer.2014.03.055 · Cited by 37
Pseudo-tetrablock copolymers with ethylene and a functionalized comonomer
Coffin, R. C., Diamanti, S. J., Hotta, A., Khanna, V., Krämer, E. J., Fredrickson, G. H., & Bazan, G. C. (2007) · Chemical Communications · doi:10.1039/b705808j · Cited by 37
Mechanical Properties and Morphology of Propene–Pentene Isotactic Copolymers
Rosa, C. D., Scoti, M., Auriemma, F., de Ballesteros, O. R., Talarico, G., Malafronte, A., & Girolamo, R. D. (2018) · Macromolecules · doi:10.1021/acs.macromol.8b00362 · Cited by 35
Guo, H., Wang, J., Zhou, C., Zhang, W., Wang, Z., Xu, B., Li, J., Shang, Y., Christiansen, J. D. C., Yu, D., et al. (2015) · Polymer · doi:10.1016/j.polymer.2015.06.013 · Cited by 34
How Nascent Structure of Semicrystalline Polymer Powders Enhances Bulk Mechanical Properties
Jauffrès, D., Lame, O., Vigier, G., & Doré, F. (2008) · Macromolecules · doi:10.1021/ma801133v · Cited by 34
Osaka, N., Yanagi, K., & Saito, H. (2013) · Polymer Journal · doi:10.1038/pj.2013.26 · Cited by 34
Xiong, B., Lame, O., Chenal, J., Rochas, C., & Séguéla, R. (2016) · eXPRESS Polymer Letters · doi:10.3144/expresspolymlett.2016.29 · Cited by 34
Block Formation during Polymer Crystallization
Hippler, T., Jiang, S., & Strobl, G. R. (2005) · Macromolecules · doi:10.1021/ma051337u · Cited by 34
Self-citationLv, Y., Huang, Y., Kong, M., Yang, J., Yang, Q. Y., & Li, G. (2014) · Composites Science and Technology · doi:10.1016/j.compscitech.2014.03.011 · Cited by 33
Bartczak, Z. (2018) · Polymer Testing · doi:10.1016/j.polymertesting.2018.04.027 · Cited by 34
Wang, L., Hikima, Y., Ohshima, M., Sekiguchi, T., & Yano, H. (2018) · RSC Advances · doi:10.1039/c8ra01833b · Cited by 33
Mowery, D. M., Harris, D. J., & Schmidt‐Rohr, K. (2006) · Macromolecules · doi:10.1021/ma0513517 · Cited by 33
Effect of cavitation on the plastic deformation and failure of isotactic polypropylene
Na, B., & Lv, R. (2007) · Journal of Applied Polymer Science · doi:10.1002/app.26594 · Cited by 33
An experimental, theoretical and numerical investigation of shape memory polymers
Scalet, G., Auricchio, F., Bonetti, E., Castellani, L., Ferri, D., Pachera, M., & Scavello, F. (2014) · International Journal of Plasticity · doi:10.1016/j.ijplas.2014.10.006 · Cited by 34
“(9), is possible under the hypothesis of material incompressibility, which is valid for the material under investigation (Hiss et al., 1999).”
Investigation of the Mesostructure of a Mechanically Deformed HDPE by Synchrotron Microtomography
Blaise, A., Baravian, C., André, S., Dillet, J., Michot, L. J., & Mokso, R. (2010) · Macromolecules · doi:10.1021/ma101033b · Cited by 33
The viscoelastic and viscoplastic behavior of low-density polyethylene
Drozdov, A. D., & Yuan, Q. (2003) · International Journal of Solids and Structures · doi:10.1016/s0020-7683(03)00074-x · Cited by 33
A Common Multiscale Feature of the Deformation Mechanisms of a Semicrystalline Polymer
Farge, L., André, S., Meneau, F., Dillet, J., & Cunat, C. (2013) · Macromolecules · doi:10.1021/ma4019747 · Cited by 32
Liu, D., Li, Y., Xu, H., Tian, H., & Xiang, A. (2018) · Polymer Composites · doi:10.1002/pc.25084 · Cited by 32
Effect of Submicron Structures on the Mechanical Behavior of Polyethylene
Kishimoto, M., Mita, K., Ogawa, H., & Takenaka, M. (2020) · Macromolecules · doi:10.1021/acs.macromol.0c00896 · Cited by 34
Zhang, W., Zhang, G., Lu, X., Wang, J., & Wu, D. (2021) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2021.118093 · Cited by 32
Stretch-induced bidirectional polymorphic transformation of crystals in poly(butylene adipate)
Song, Y., Ye, H., Xu, J., Hou, K., Zhou, Q., & Lu, G. (2014) · Polymer · doi:10.1016/j.polymer.2014.05.011 · Cited by 33
Monge, M. Á., Díaz, J. A., & Pareja, R. (2004) · Macromolecules · doi:10.1021/ma049103i · Cited by 32
Bone-inspired stress-gaining elastomer enabled by dynamic molecular locking
Wang, Y., Guan, Q., Guo, Y., Sun, L., Neisiany, R. E., Guo, X., Huang, H., Yang, L., & You, Z. (2024) · Science Advances · doi:10.1126/sciadv.adk5177 · Cited by 31
“As a result of the disentanglements and slippages of molecular chains, high-density polyethylene ( 7 ) and thermoplastic polyurethane ( 8 ), both of which are thermoplastic (linear) polymers, exhibited an SLE of − 0.0905 and − 0.2441, respectively.”
InfluentialMao, Y., Li, X., Burger, C. P., Hsiao, B. S., Mehta, A. K., & Tsou, A. H. (2012) · Macromolecules · doi:10.1021/ma3015504 · Cited by 31
Lezak, E., & Bartczak, Z. (2007) · Macromolecules · doi:10.1021/ma0708038 · Cited by 31
Li, Y., Li, Y., Cao, R., Xie, J., & Chen, W. (2024) · Macromolecules · doi:10.1021/acs.macromol.4c01098 · Cited by 33
Li, M., Liu, W., & Zhu, S. (2017) · Polymer · doi:10.1016/j.polymer.2017.02.006 · Cited by 30
Yang, F., Wang, X., Ma, Z., Wang, B., Pan, L., & Li, Y. (2020) · Polymers · doi:10.3390/polym12010089 · Cited by 31
Kida, T., Hiejima, Y., Nitta, K., & Yamaguchi, M. (2022) · Polymer · doi:10.1016/j.polymer.2022.124869 · Cited by 32
Na, B., Lv, R., Xu, W., Yu, P., Wang, K., & Fu, Q. (2007) · The Journal of Physical Chemistry B · doi:10.1021/jp075990q · Cited by 30
Ren, C., Jiang, Z., Du, X., Men, Y., & Tang, T. (2009) · The Journal of Physical Chemistry B · doi:10.1021/jp9063164 · Cited by 30
Molecular View of Properties of Random Copolymers of Isotactic Polypropylene
Auriemma, F., Rosa, C. D., Girolamo, R. D., Malafronte, A., Scoti, M., & Cioce, C. (2016) · Advances in polymer science · doi:10.1007/12_2016_350 · Cited by 32
Coppola, B., Scarfato, P., Incarnato, L., & Maio, L. D. (2017) · Polymers · doi:10.3390/polym9060235 · Cited by 30
Time-dependent response of polypropylene after strain reversal
Drozdov, A. D. (2010) · International Journal of Solids and Structures · doi:10.1016/j.ijsolstr.2010.08.001 · Cited by 30
Mohammadi, M., Yousefi, A. A., & Ehsani, M. (2011) · Journal of Applied Polymer Science · doi:10.1002/app.36246 · Cited by 30
Metadata
- Authors
- Hiss, R., Hobeika, S., Lynn, C., & Strobl, G.
- Affiliations
- University of Freiburg (DE)
- Venue
- Macromolecules
- Publisher
- American Chemical Society (ACS)
- Published
- 1999-06-01
- Volume
- 32
- Issue
- 13
- Pages
- 4390-4403
- ISSN
- 0024-9297 (ISSN-L)
- 1520-5835
- OpenAlex
- W1964100411
- Semantic Scholar
- 001144c6520c7f808e72de547a96271a0ae7d26f
- Cited by
- 540
- References
- 32
- Citations by year
- 2026: 25 · 2025: 23 · 2024: 29 · 2023: 23 · 2022: 19 · 2021: 26 · 2020: 23 · 2019: 27 · 2018: 40 · 2017: 29 · 2016: 19 · 2015: 15 · 2014: 18 · 2013: 24 · 2012: 22
- FWCI
- 7.41
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- Macromolecules (publishedVersion)
- FreiDok plus (Universitätsbibliothek Freiburg) (submittedVersion)
- Topics
- Physical Sciences › Materials Science › Polymers and Plastics › Polymer crystallization and properties
- Physical Sciences › Materials Science › Metals and Alloys › Microstructure and mechanical properties
- Physical Sciences › Chemical Engineering › Fluid Flow and Transfer Processes › Rheology and Fluid Dynamics Studies
- Keywords
- polyethylene, low-density polyethylene, uniaxial drawing, chain disentanglement, crystallinity, necking, true stress-strain curves, crystallographic texture, irreversible deformation
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.