Network Stretching, Slip Processes, and Fragmentation of Crystallites during Uniaxial Drawing of Polyethylene and Related Copolymers. A Comparative Study
The DOI matches its Crossref record; 33 of the 33 references it cites were found in a registry or an index.
Abstract
When polyethylene (PE) is deformed to large strains, the stress originates from both the viscous forces associated with the plastic deformation of the crystallites by slip and fragmentation processes and the entropic elastic forces arising from the stretching of the entangled amorphous regions. Relative weights of the different processes change with the crystallinity. The dependencies were analyzed in a comprehensive study on a series of samples encompassing a large range of crystallinities: PE, low-density PE (LDPE), and ethylene−vinylacetate copolymers. The comparison was based on measured true stress−strain curves for constant strain rates. For the samples with higher crystallinity, which show a necking, this was achieved by employing a video-controlled tensile testing machine. Recovery properties of the sample were studied in step-cycle runs, where the load was applied stepwise and interrupted after each step by an unloading−reloading loop. Simultaneous with the mechanical testing, the related texture changes were determined by a measurement of the WAXS patterns. In spite of the large changes in the gross mechanical properties from solid- to rubberlike, there exists a common general scheme for the deformation behavior. For all samples, one finds four characteristic points where the differential compliance changes. They may be associated with (1) the onset of isolated slip processes, (2) a change into a collective activity of the slips, (3) the beginning of crystallite fragmentation, and (4) chain disentanglement resulting in a finite truly irreversible deformation. When the crystallinity is increased, the stresses at the four transition points also increase. The related strains, however, remain essentially constant. Crystal textures are also a function of the imposed strain only, the dependencies being common for all samples. Experiments support the novel picture of a granular substructure of the crystalline lamellae as a basic structural feature. Block slips with the three surfaces as slip planes enable the system to easily react on each imposed strain in a well-defined way.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“The curve for X-direction elongation in figure 2 has the same typical shape as those obtained from laboratory experiments on PE, for instance the experiments using strain rates between 10-4 and 10-2 s-1 performed by Hiss et al [17] and Addiego et al [18].”
In the citing paper
“Hiss et al [17] and Addiego et al [18] also found that increasing strain rate increases the yield stress.”
In the citing paper
“Moreover, the curve of virgin PE agrees quite well with the true stress-true strain curves obtained in tensile deformation mode for polyethylene of similar molecular characteristics [4,45].”
From Erosion of the molecular network in the amorphous layers of polyethylene upon high-strain deformation (2016) · cites this paper as [4]
In the citing paper
“This transition was postulated to be a result of intensified crystal fragmentation and presumably chain disentanglement beginning in amorphous phase that should lead to a partial disintegration of the molecular network [4].”
From Erosion of the molecular network in the amorphous layers of polyethylene upon high-strain deformation (2016) · cites this paper as [4]
In the citing paper
“The same is actually true for semicrystalline polymers, since their deformation can be considered as a simultaneous deformation of two co-continuous interlaced network-like structures: a skeleton made up of crystallites interconnected with the interlamellar layers of entangled amorphous phase [4]”
From Erosion of the molecular network in the amorphous layers of polyethylene upon high-strain deformation (2016) · cites this paper as [4]
3 more claims about this paper
Create a free account to see every claim other papers make about this one.
Citations
Cites
Strobl, G. R. (1996) · Springer eBooks · doi:10.1007/978-3-662-03243-5 · Cited by 1,497
Self-citationMolecular model of drawing polyethylene and polypropylene
Peterlin, A. (1971) · Journal of Materials Science · doi:10.1007/bf00550305 · Cited by 987
The use of a mathematical model to describe isothermal stress-strain curves in glassy thermoplastics
Haward, R. N., & Thackray, G. (1968) · Proceedings of the Royal Society of London. Series A. Mathematical and Physical Sciences · doi:10.1098/rspa.1968.0029 · Cited by 646
Deformation mechanisms in crystalline polymers
Bowden, P. B., & Young, R. J. (1974) · Journal of Materials Science · doi:10.1007/bf00540553 · Cited by 551
Determination of the plastic behaviour of solid polymers at constant true strain rate
G'sell, C., & Jonas, J. J. (1979) · Journal of Materials Science · doi:10.1007/bf00772717 · Cited by 439
Strain hardening of thermoplastics
Haward, R. N. (1993) · Macromolecules · doi:10.1021/ma00074a006 · Cited by 326
The necking and cold-drawing of rigid plastics
Vincent, P. I. (1960) · Polymer · doi:10.1016/0032-3861(60)90003-3 · Cited by 320
Video-controlled tensile testing of polymers and metals beyond the necking point
G'Sell, C., Hiver, J. M., Dahoun, A., & Souahi, A. (1992) · Journal of Materials Science · doi:10.1007/bf01105270 · Cited by 299
Phase Transformation and Deformation Processes in Oriented Polyethylene
Seto, T., Hara, T., & Tanaka, K. (1968) · Japanese Journal of Applied Physics · doi:10.1143/jjap.7.31 · Cited by 266
Polymer deformation in terms of spherulites
Hay, I. L., & Keller, A. (1965) · Kolloid-Zeitschrift & Zeitschrift für Polymere · doi:10.1007/bf01500379 · Cited by 255
Research works printed but not linked: 7
- Haward R., 1968, Proc. R. Soc. A, 302, 453
- Takahashi Y., 1988, Part B: Polym. Phys
- Bridgman P., 1944, Trans. Am. Soc. Met., 32, 553
- Hiss, R. Ph.D. Thesis, Freiburg, 1996.
- Gauthier C., 10th International Conference on Deformation, Yield and Fracture of Polymers; Institute of Materials: London
- Krigas T., 1985, J. Polym. Sci., 23, 509
- Kelly A., 1970, Crystallography of Crystal Defects
Cited by
Items 301–400 of 545
Zhang, W., Chen, J., Qi, Y., Zhang, Q., Zhao, J., Wu, T., Wang, D., Meng, L., Chen, W., & Li, L. (2021) · Polymer Testing · doi:10.1016/j.polymertesting.2021.107143 · Cited by 14
Lu, Y., Lyu, D., Han, C., & Men, Y. (2023) · Macromolecules · doi:10.1021/acs.macromol.3c00955 · Cited by 14
Li, S., Litvinov, V. M., & Men, Y. (2024) · Macromolecules · doi:10.1021/acs.macromol.4c01200 · Cited by 15
Okita, S., Hasegawa, M., Takahashi, Y., Puppulin, L., Sudo, A., & Pezzotti, G. (2013) · Journal of the mechanical behavior of biomedical materials/Journal of mechanical behavior of biomedical materials · doi:10.1016/j.jmbbm.2013.01.022 · Cited by 14
Chang, B., Schneider, K., & Heinrich, G. (2017) · Macromolecular Materials and Engineering · doi:10.1002/mame.201700152 · Cited by 14
Farge, L., André, S., & Boisse, J. (2018) · Polymer · doi:10.1016/j.polymer.2018.07.076 · Cited by 14
Balobanov, V., Verho, T., Heino, V., Ronkainen, H., & Pelto, J. (2020) · Polymer Testing · doi:10.1016/j.polymertesting.2020.106936 · Cited by 14
Rungswang, W., Jarumaneeroj, C., Jirasukho, P., Juabrum, S., Pakawanit, P., Soontaranon, S., & Rugmai, S. (2021) · ACS Applied Polymer Materials · doi:10.1021/acsapm.1c01159 · Cited by 14
Suppressed molecular orientation in nylon 6/clay nanocomposite at large strain: Role of microvoiding
Na, B., Xu, W., Lv, R., Tian, N., Li, Z., Su, R. Z., & Fu, Q. (2010) · Journal of Polymer Science Part B Polymer Physics · doi:10.1002/polb.21915 · Cited by 14
Yang, X. G., Sun, Y., Liao, T., & Men, Y. (2020) · Polymer · doi:10.1016/j.polymer.2020.122612 · Cited by 14
Wanyan, Q., Qiu, Y., Xi, J., Yin, S., Zhang, W., & Wu, D. (2020) · ACS Applied Polymer Materials · doi:10.1021/acsapm.0c01107 · Cited by 14
Viljoen, D., Fischer, M., Kuehnert, I., & Labuschagné, F. J. W. J. (2021) · Polymers · doi:10.3390/polym13040527 · Cited by 14
Weng, G., Wu, J., Xu, Y., Bao, J., Huang, G., & Chen, Z. (2014) · Journal of Polymer Research · doi:10.1007/s10965-014-0576-3 · Cited by 14
Stress-strain behavior of high-density polyethylene below the yield point: Effect of unloading rate
Патлажан, С. А., Hizoum, K., & Rémond, Y. (2008) · Polymer Science Series A · doi:10.1134/s0965545x08050040 · Cited by 14
Molecular Mobility and Phase Composition in Polyolefins: From Fundamental to Applied Research
Litvinov, V. M. (2011) · ACS symposium series · doi:10.1021/bk-2011-1077.ch011 · Cited by 14
Chang, A., Cheung, Y. W., Hiltner, A., & Baer, E. (2001) · Journal of Polymer Science Part B Polymer Physics · doi:10.1002/polb.10066 · Cited by 14
Effect of the molecular network on high-strain compression of cross-linked polyethylene
Bartczak, Z. (2012) · European Polymer Journal · doi:10.1016/j.eurpolymj.2012.09.006 · Cited by 13
Strong and tough semi-crystalline poly(aryl ether nitrile) with low coefficient of thermal expansion
Nie, M., Mo, C., He, L., Feng, X., Liu, X., & Tong, L. (2024) · Polymer · doi:10.1016/j.polymer.2024.127363 · Cited by 13
Chen, Y., Zhong, G., Hsiao, B. S., & Li, Z. (2013) · Journal of Polymer Science Part B Polymer Physics · doi:10.1002/polb.23376 · Cited by 13
Wanyan, Q., Qiu, Y., Zhang, W., Yu, H., & Wu, D. (2021) · Polymer · doi:10.1016/j.polymer.2021.123628 · Cited by 14
Mechanical responses of Semi-crystalline thermoplastic polymers at various temperatures
Song, R., Berer, M., & Muliana, A. H. (2021) · International Journal of Solids and Structures · doi:10.1016/j.ijsolstr.2021.111398 · Cited by 13
Stretching-Induced Melting and Recrystallization Polymorphism Revealed in Polybutene-1
Li, W., Zhang, D., Qv, C., Zhao, R., & Ma, Z. (2023) · Macromolecules · doi:10.1021/acs.macromol.2c02372 · Cited by 13
Zhou, Y., Yang, J. H., Zhou, Z., Hao, T., & Nie, Y. (2023) · Chinese Journal of Polymer Science · doi:10.1007/s10118-023-2974-7 · Cited by 14
Zhang, C., Yang, J.-L., Huang, Y., & Li, G. (2023) · Chinese Journal of Polymer Science · doi:10.1007/s10118-023-3028-x · Cited by 13
Lv, J., Chen, X., Wu, Z., Li, Y., & Chen, W. (2023) · Chinese Journal of Polymer Science · doi:10.1007/s10118-023-3017-0 · Cited by 13
Nature of molecular network in thermal shrinkage behavior of oriented high‐density polyethylene
Fu, L., Jiang, Z., Enderle, H., Lilge, D., Li, X., Funari, S. S., & Men, Y. (2013) · Journal of Polymer Science Part B Polymer Physics · doi:10.1002/polb.23420 · Cited by 13
The effect of temperature on the viscoelastic response of rubbery polymers at finite strains
Drozdov, A. D., & Dorfmann, L. (2002) · Acta Mechanica · doi:10.1007/bf01170707 · Cited by 13
“Slip [34] and fragmentation [35] of crystallites driven by network stretching.”
BackgroundJiang, Z., Liao, T., Chen, R., & Men, Y. (2019) · Polymer · doi:10.1016/j.polymer.2019.121984 · Cited by 13
Wang, Y., Wang, Z., Zhu, P., Liu, X., Wang, L., Dong, X., & Wang, D. (2021) · RSC Advances · doi:10.1039/d0ra10627e · Cited by 14
Chen, W., Li, X., Liu, Y., Li, J., Zhou, W., Chen, L., & Li, L. (2015) · Chinese Journal of Polymer Science · doi:10.1007/s10118-015-1613-3 · Cited by 13
Micromechanical approach to modeling damage in crystalline polyethylene
Alvarado-Contreras, J. A., Polak, M. A., & Penlidis, A. (2007) · Polymer Engineering and Science · doi:10.1002/pen.20661 · Cited by 13
Li, Y., Duan, T., Yao, G., Tang, Y., Miao, W., & Wang, Z. (2019) · Composites Science and Technology · doi:10.1016/j.compscitech.2019.107798 · Cited by 12
Contino, M., Andena, L., Valle, V. L., Rink, M., Marra, G., & Resta, S. (2019) · Mechanics of Time-Dependent Materials · doi:10.1007/s11043-019-09426-z · Cited by 12
Tensile Creep Failure of Isotactic Polypropylene under the Strain Criterion
Liu, P., Peng, L., Chen, J., Yang, B., Chen, Y., Luo, Z., Han, C. C.-C., Huang, X., & Men, Y. (2022) · Macromolecules · doi:10.1021/acs.macromol.2c01263 · Cited by 12
Plastic Deformation of High Density Polyethylene with Extended-Chain Crystal Morphology
Vozniak, A., & Bartczak, Z. (2022) · Polymers · doi:10.3390/polym15010066 · Cited by 12
“Since the strain-hardening is controlled primarily by the density of the molecular network in the amorphous phase [6,11], the observed response of the reference samples can indicate similar properties of the molecular network, perhaps with a slightly higher network density in the H3-ref sample.”
BackgroundInfluentialLitvinov, V., Koning, C. C., & Tijssen, J. (2014) · Polymer · doi:10.1016/j.polymer.2014.11.025 · Cited by 12
André, S., Renault, N., Meshaka, Y., & Cunat, C. (2011) · Continuum Mechanics and Thermodynamics · doi:10.1007/s00161-011-0205-x · Cited by 13
Blaise, A., André, S., Delobelle, P., Meshaka, Y., & Cunat, C. (2016) · Mechanics of Time-Dependent Materials · doi:10.1007/s11043-016-9312-1 · Cited by 12
“At this point, the force reaches a maximum in agreement with the first Considere condition (Hiss et al. 1999).”
BackgroundChen, X., Zhang, W., Ye, K., Meng, L., Lv, F., Cao, T., Wan, C., Chen, X., & Li, L. (2018) · Journal of Polymer Science Part B Polymer Physics · doi:10.1002/polb.24740 · Cited by 12
Yang, S., Wei, Q.-Y., Gao, X., Zhou, L., Xu, L., Tang, J., Zhong, G., Ji, X., & Li, Z. (2019) · Polymer · doi:10.1016/j.polymer.2019.122099 · Cited by 12
Correlation between High Temperature Deformation and β Relaxation in LaCe-Based Metallic Glass
Chen, Y., & Qiao, J. C. (2020) · Materials · doi:10.3390/ma13040833 · Cited by 12
“of strain on the plastic deformation of polymers have also been studied, and related mechanisms have been discussed in previous studies [22,23].”
BackgroundNetwork alteration theory on Mullins effect in semicrystalline polymers
Wang, M., Shen, J., Li, J., & Guo, S. (2014) · Polymer International · doi:10.1002/pi.4762 · Cited by 12
Determination of Critical Strains in Isotactic Polypropylene by Cyclic Loading-Unloading
Spieckermann, F., Wilhem, H. R., Schafler, E., Alfantis, E. C., & Zehetbauer, M. (2008) · Journal of Engineering Materials and Technology · doi:10.1115/1.3030938 · Cited by 12
Song, Y., & Nemoto, N. (2005) · Polymer · doi:10.1016/j.polymer.2005.05.058 · Cited by 12
Li, R., Yang, G., Qin, Y., Liu, L., & Jiang, Z. (2019) · Chinese Journal of Polymer Science · doi:10.1007/s10118-020-2362-5 · Cited by 12
Song, Y., Shigematsu, Y., Nitta, K., & Nemoto, N. (2002) · Polymer Journal · doi:10.1295/polymj.34.584 · Cited by 12
Riccò, T., & Pegoretti, A. (2001) · Journal of Polymer Science Part B Polymer Physics · doi:10.1002/polb.10085 · Cited by 12
Enhanced ductility in high performance polyamides due to strain-induced phase transitions
Candau, N., Chenal, J., Lame, O., Schouwink, P., Michaud, V. J., Plummer, C. J. G., & Frauenrath, H. (2021) · Polymer · doi:10.1016/j.polymer.2021.124424 · Cited by 11
Molecular Order in Cold Drawn, Strain-Recrystallized Poly(ε-caprolactone)
Kossack, W., Seidlitz, A., Thurn‐Albrecht, T., & Kremer, F. (2017) · Macromolecules · doi:10.1021/acs.macromol.6b02714 · Cited by 11
Li, X., Lin, Y., Su, F., Chen, X., Lv, F., Meng, L., Zhang, Q., & Li, L. (2017) · Macromolecular Materials and Engineering · doi:10.1002/mame.201700178 · Cited by 11
Yang, P., Zhao, L. X., Pan, X., Zhou, F., Yang, Z., & He, X. (2020) · Polymer Testing · doi:10.1016/j.polymertesting.2020.106555 · Cited by 11
Li, Y., Ma, G.-Q., Sun, Y., Huang, H., Pan, M., Zhang, G., Zhong, G., & Li, Z. (2020) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.0c03510 · Cited by 11
Şen, B. O., Çetin, S., Yahşi, U., & Soykan, U. (2021) · Journal of Polymer Research · doi:10.1007/s10965-021-02646-3 · Cited by 11
Chen, Z., Xiong, B., Li, Z., Yao, K., & Li, X. (2022) · Polymer · doi:10.1016/j.polymer.2022.125599 · Cited by 11
Li, X., Mao, Y., Burger, C. P., Che, J., Hsiao, B. S., Kulkarni, R. R., & Tsou, A. H. (2013) · Polymer · doi:10.1016/j.polymer.2013.06.017 · Cited by 11
Finite viscoplasticity of semicrystalline polymers
Drozdov, A. D., & Christiansen, J. D. C. (2003) · Archive of Applied Mechanics · doi:10.1007/s00419-002-0268-z · Cited by 11
Coutry, S., & Spells, S. J. (2003) · Polymer · doi:10.1016/s0032-3861(03)00040-5 · Cited by 11
Micro‐FT‐IR study of stretching a single filament: Polymorphic transition in nylon 6
Na, B., Lv, R., Tian, N., Xu, W., Li, Z., & Fu, Q. (2009) · Journal of Polymer Science Part B Polymer Physics · doi:10.1002/polb.21696 · Cited by 11
Tian, H., Wang, Y., Wu, C., & Wang, B. (2024) · Macromolecules · doi:10.1021/acs.macromol.4c00275 · Cited by 10
Shao, C., Ma, Z., Zhuo, R., Zhang, R., & Shen, C. (2011) · Journal of Materials Science · doi:10.1007/s10853-011-6173-5 · Cited by 10
Effects of Crosshead Speed on the Quasi-Static Stress–Strain Relationship of Polyethylene Pipes
Zhang, Y., & Jar, P. ‐. B. (2016) · Journal of Pressure Vessel Technology · doi:10.1115/1.4033777 · Cited by 10
Kida, T., Hiejima, Y., & Nitta, K. (2018) · Polymer International · doi:10.1002/pi.5533 · Cited by 10
Trigg, E. B., Middleton, L. R., Yan, L. T., & Winey, K. I. (2018) · Macromolecules · doi:10.1021/acs.macromol.8b01639 · Cited by 10
Insight into the Excellent Tribological Performance of Highly Oriented Poly(phenylene sulfide)
Zhang, L.-Q., Yang, S.-G., Zhang, J., Zhong, K.-P., Zhao, Z., Chen, Y., Lei, J., Zhang, Q., & Li, Z.-M. (2022) · Chinese Journal of Polymer Science · doi:10.1007/s10118-022-2672-x · Cited by 11
Na, B., Lv, R., & Xu, W. (2009) · Journal of Applied Polymer Science · doi:10.1002/app.30532 · Cited by 10
Effect of annealing on the viscoelastic and viscoplastic responses of low‐density polyethylene
Drozdov, A. D., & Yuan, Q. (2003) · Journal of Polymer Science Part B Polymer Physics · doi:10.1002/polb.10507 · Cited by 10
Strain rate dependent damage evolution in long glass fiber reinforced polypropylene
Lienhard, J., Discher, D. E., & Hohe, J. (2020) · Composites Science and Technology · doi:10.1016/j.compscitech.2020.108007 · Cited by 10
Zhang, R., He, Q., Yu, H., Li, J., Hu, Y., & Qian, J. (2024) · Polymers · doi:10.3390/polym16233236 · Cited by 9
Liao, S., Wang, Y.-T., Mao, X., Wu, M., & Wang, Z. (2024) · Polymer · doi:10.1016/j.polymer.2024.127950 · Cited by 9
Deformation-induced crystalline structure evolutions of isotactic poly-1-butene
Guo, H., Zhou, C., Zhang, W., Wang, J., Li, J., Shang, Y., Meng, Y., Christiansen, J. D. C., Yu, D., Wu, Z., et al. (2016) · Colloid & Polymer Science · doi:10.1007/s00396-016-3964-x · Cited by 9
“An orientational order parameter proposed long time ago by Hermanns [3] is often used to express quantitatively the degree of orientation of a set of lattice planes hkl in uniaxially oriented samples.”
BackgroundMethodInfluentialFarge, L., Boisse, J., Bihannic, I., Díaz, A., & André, S. (2017) · Journal of Polymer Science Part B Polymer Physics · doi:10.1002/polb.24527 · Cited by 9
The stress relaxation behavior of isotactic poly(1‐butene) and its ethylene copolymers
Al‐Hussein, M., & Strobl, G. R. (2004) · Journal of Polymer Science Part B Polymer Physics · doi:10.1002/polb.20083 · Cited by 9
Self-citationTensile behaviors of polyamide 6/UHLE blends
Luo, H., Fu, Z., Jing, B., Shi, J. G., Zou, X., & Dai, W. (2009) · Journal of Materials Science · doi:10.1007/s10853-009-3494-8 · Cited by 9
Zhao, J., Sun, Y., & Men, Y. (2017) · ACS Omega · doi:10.1021/acsomega.7b01269 · Cited by 9
Equilibrium Crystallization Temperature of Syndiotactic Polystyrene γ Form
Wang, H., Wu, C., Cui, D., & Men, Y. (2018) · Chinese Journal of Polymer Science · doi:10.1007/s10118-018-2059-1 · Cited by 9
Finite viscoelasticity and viscoplasticity of semicrystalline polymers
Drozdov, A. D. (2007) · Continuum Mechanics and Thermodynamics · doi:10.1007/s00161-007-0049-6 · Cited by 9
Constitutive Modeling of Damage Evolution in Semicrystalline Polyethylene
Alvarado-Contreras, J. A., Polak, M. A., & Penlidis, A. (2010) · Journal of Engineering Materials and Technology · doi:10.1115/1.4002367 · Cited by 12
Petisco-Ferrero, S., Cardinaels, R., & Breemen, V. L. L. (2019) · Polymer · doi:10.1016/j.polymer.2019.121918 · Cited by 9
Role of Crystal Thickness on the Critical Tie Molecule Fraction in Semicrystalline Polymers
Gunter, K. M., & Register, R. A. (2025) · Macromolecules · doi:10.1021/acs.macromol.5c02290 · Cited by 8
Developing highly flame-retardant PA6-based composites via in-situ PPS nanofiber network
Mahmud, M. B., Rahman, S. S., Fashandi, M., Amirabadi, S., Zheng, W., & Park, C. B. (2024) · Polymer · doi:10.1016/j.polymer.2024.127296 · Cited by 8
Chen, Z., Wang, Y., Xiong, B., & Zhu, J. (2024) · Macromolecules · doi:10.1021/acs.macromol.4c00777 · Cited by 8
Misra, R. D. K., & Yuan, Q. (2012) · Materials Science and Engineering C · doi:10.1016/j.msec.2012.02.010 · Cited by 8
Różański, A. (2018) · Journal of Polymer Science Part B Polymer Physics · doi:10.1002/polb.24638 · Cited by 8
Huang, Y., Zhang, Q., Lü, X., Gong, Y., Zhou, H., & Feng, J. (2019) · Chinese Journal of Polymer Science · doi:10.1007/s10118-020-2364-3 · Cited by 8
Yang, B., Zhao, H. C., Zhang, C., Zhang, X., Dong, X., Liu, G., & Wang, D. (2022) · CrystEngComm · doi:10.1039/d2ce01247b · Cited by 8
Smith, T., Gupta, C., Siavoshani, A. Y., & Wang, S. (2023) · Polymer · doi:10.1016/j.polymer.2023.125878 · Cited by 8
YOSHIDA, T., Nakane, T., OKADA, E., Sakurai, S., UCHIDA, M., & KANEKO, Y. (2023) · Polymer · doi:10.1016/j.polymer.2023.126190 · Cited by 8
Zhou, J., Xu, S., Song, J. Z., Zheng, Y., Yu, C., Shan, G., Bao, Y., & Pan, P. (2023) · Polymer · doi:10.1016/j.polymer.2023.126378 · Cited by 8
Tranchida, D., Bartczak, Z., Bieliński, D. M., Kiflie, Z., Andrzej, G., & Piccarolo, S. (2009) · Polymer · doi:10.1016/j.polymer.2009.02.032 · Cited by 8
Zhao, H., Liu, X., Sui, Y., Zhang, Y., & Zhao, G. (2017) · Polymer Testing · doi:10.1016/j.polymertesting.2017.04.012 · Cited by 8
Characterization of strain bursts in high density polyethylene by means of a novel nano creep test
Wilhelm, H., Spieckermann, F., Fischer, C., Polt, G., & Zehetbauer, M. (2019) · International Journal of Plasticity · doi:10.1016/j.ijplas.2019.01.010 · Cited by 8
Movva, S., Burrell, R. K., Pooyan, P., Garmestani, H., & Jacob, K. I. (2022) · Polymer · doi:10.1016/j.polymer.2022.124649 · Cited by 8
Evaluating the Residual Stress and Its Effect on the Quasi-Static Stress in Polyethylene Pipes
Tan, N., Lin, L., Deng, T., & Dong, Y. (2022) · Polymers · doi:10.3390/polym14071458 · Cited by 8
“In an engineering stress–strain curve, the yield stress for necking samples is the peak stress, while for non-necking samples, it is determined on the curve at which the maximum value of the curvature takes place [20].”
BackgroundYang, L., Niu, Y., Wang, H., & Wang, Z. (2008) · Polymer · doi:10.1016/j.polymer.2008.11.033 · Cited by 8
Nano- and Micromechanics of Crystalline Polymers
Gałęski, A., & Régnier, G. (2009) · Carl Hanser Verlag GmbH & Co. KG eBooks · doi:10.3139/9783446430129.001 · Cited by 9
Surface Spectroscopic Signatures of Mechanical Deformation in High-Density Polyethylene (HDPE)
Averett, S. C., Stanley, S. K., Hanson, J. J., Smith, S. J., & Patterson, J. E. (2018) · Applied Spectroscopy · doi:10.1177/0003702818757232 · Cited by 8
Chang, B., Shi, H.-H., He, M., Schneider, K., Heinrich, G., Liu, C., & Shen, C. (2020) · Polymer · doi:10.1016/j.polymer.2020.123342 · Cited by 8
Na, B., & Lv, R. (2006) · Journal of Polymer Science Part B Polymer Physics · doi:10.1002/polb.20932 · Cited by 8
Crystallinity and Crystallographic Texture in Isotactic Polypropylene during Deformation and HeatingPreprint
Jia, J., & Raabe, D. (2008) · arXiv (Cornell University) · doi:10.48550/arxiv.0811.2412 · Cited by 8
“alline material in semi-crystalline polymers has also been referred to as disaggregation [17]. Similar observations and related conclusions were during the last years published by the group of Strobl [27, 28, 29, 30, 31] on the basis of data obtained from uniaxial tensile testing. In these investigations the authors s…”
Background
Metadata
- Authors
- Hiss, R., Hobeika, S., Lynn, C., & Strobl, G.
- Affiliations
- University of Freiburg (DE)
- Venue
- Macromolecules
- Publisher
- American Chemical Society (ACS)
- Published
- 1999-06-01
- Volume
- 32
- Issue
- 13
- Pages
- 4390-4403
- ISSN
- 0024-9297 (ISSN-L)
- 1520-5835
- OpenAlex
- W1964100411
- Semantic Scholar
- 001144c6520c7f808e72de547a96271a0ae7d26f
- Cited by
- 540
- References
- 32
- Citations by year
- 2026: 25 · 2025: 23 · 2024: 29 · 2023: 23 · 2022: 19 · 2021: 26 · 2020: 23 · 2019: 27 · 2018: 40 · 2017: 29 · 2016: 19 · 2015: 15 · 2014: 18 · 2013: 24 · 2012: 22
- FWCI
- 7.41
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- Macromolecules (publishedVersion)
- FreiDok plus (Universitätsbibliothek Freiburg) (submittedVersion)
- Topics
- Physical Sciences › Materials Science › Polymers and Plastics › Polymer crystallization and properties
- Physical Sciences › Materials Science › Metals and Alloys › Microstructure and mechanical properties
- Physical Sciences › Chemical Engineering › Fluid Flow and Transfer Processes › Rheology and Fluid Dynamics Studies
- Keywords
- polyethylene, low-density polyethylene, uniaxial drawing, chain disentanglement, crystallinity, necking, true stress-strain curves, crystallographic texture, irreversible deformation
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.