Network Stretching, Slip Processes, and Fragmentation of Crystallites during Uniaxial Drawing of Polyethylene and Related Copolymers. A Comparative Study
The DOI matches its Crossref record; 33 of the 33 references it cites were found in a registry or an index.
Abstract
When polyethylene (PE) is deformed to large strains, the stress originates from both the viscous forces associated with the plastic deformation of the crystallites by slip and fragmentation processes and the entropic elastic forces arising from the stretching of the entangled amorphous regions. Relative weights of the different processes change with the crystallinity. The dependencies were analyzed in a comprehensive study on a series of samples encompassing a large range of crystallinities: PE, low-density PE (LDPE), and ethylene−vinylacetate copolymers. The comparison was based on measured true stress−strain curves for constant strain rates. For the samples with higher crystallinity, which show a necking, this was achieved by employing a video-controlled tensile testing machine. Recovery properties of the sample were studied in step-cycle runs, where the load was applied stepwise and interrupted after each step by an unloading−reloading loop. Simultaneous with the mechanical testing, the related texture changes were determined by a measurement of the WAXS patterns. In spite of the large changes in the gross mechanical properties from solid- to rubberlike, there exists a common general scheme for the deformation behavior. For all samples, one finds four characteristic points where the differential compliance changes. They may be associated with (1) the onset of isolated slip processes, (2) a change into a collective activity of the slips, (3) the beginning of crystallite fragmentation, and (4) chain disentanglement resulting in a finite truly irreversible deformation. When the crystallinity is increased, the stresses at the four transition points also increase. The related strains, however, remain essentially constant. Crystal textures are also a function of the imposed strain only, the dependencies being common for all samples. Experiments support the novel picture of a granular substructure of the crystalline lamellae as a basic structural feature. Block slips with the three surfaces as slip planes enable the system to easily react on each imposed strain in a well-defined way.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“The curve for X-direction elongation in figure 2 has the same typical shape as those obtained from laboratory experiments on PE, for instance the experiments using strain rates between 10-4 and 10-2 s-1 performed by Hiss et al [17] and Addiego et al [18].”
In the citing paper
“Hiss et al [17] and Addiego et al [18] also found that increasing strain rate increases the yield stress.”
In the citing paper
“Moreover, the curve of virgin PE agrees quite well with the true stress-true strain curves obtained in tensile deformation mode for polyethylene of similar molecular characteristics [4,45].”
From Erosion of the molecular network in the amorphous layers of polyethylene upon high-strain deformation (2016) · cites this paper as [4]
In the citing paper
“This transition was postulated to be a result of intensified crystal fragmentation and presumably chain disentanglement beginning in amorphous phase that should lead to a partial disintegration of the molecular network [4].”
From Erosion of the molecular network in the amorphous layers of polyethylene upon high-strain deformation (2016) · cites this paper as [4]
In the citing paper
“The same is actually true for semicrystalline polymers, since their deformation can be considered as a simultaneous deformation of two co-continuous interlaced network-like structures: a skeleton made up of crystallites interconnected with the interlamellar layers of entangled amorphous phase [4]”
From Erosion of the molecular network in the amorphous layers of polyethylene upon high-strain deformation (2016) · cites this paper as [4]
3 more claims about this paper
Create a free account to see every claim other papers make about this one.
Citations
Cites
Strobl, G. R. (1996) · Springer eBooks · doi:10.1007/978-3-662-03243-5 · Cited by 1,497
Self-citationMolecular model of drawing polyethylene and polypropylene
Peterlin, A. (1971) · Journal of Materials Science · doi:10.1007/bf00550305 · Cited by 987
The use of a mathematical model to describe isothermal stress-strain curves in glassy thermoplastics
Haward, R. N., & Thackray, G. (1968) · Proceedings of the Royal Society of London. Series A. Mathematical and Physical Sciences · doi:10.1098/rspa.1968.0029 · Cited by 646
Deformation mechanisms in crystalline polymers
Bowden, P. B., & Young, R. J. (1974) · Journal of Materials Science · doi:10.1007/bf00540553 · Cited by 551
Determination of the plastic behaviour of solid polymers at constant true strain rate
G'sell, C., & Jonas, J. J. (1979) · Journal of Materials Science · doi:10.1007/bf00772717 · Cited by 439
Strain hardening of thermoplastics
Haward, R. N. (1993) · Macromolecules · doi:10.1021/ma00074a006 · Cited by 326
The necking and cold-drawing of rigid plastics
Vincent, P. I. (1960) · Polymer · doi:10.1016/0032-3861(60)90003-3 · Cited by 320
Video-controlled tensile testing of polymers and metals beyond the necking point
G'Sell, C., Hiver, J. M., Dahoun, A., & Souahi, A. (1992) · Journal of Materials Science · doi:10.1007/bf01105270 · Cited by 299
Phase Transformation and Deformation Processes in Oriented Polyethylene
Seto, T., Hara, T., & Tanaka, K. (1968) · Japanese Journal of Applied Physics · doi:10.1143/jjap.7.31 · Cited by 266
Polymer deformation in terms of spherulites
Hay, I. L., & Keller, A. (1965) · Kolloid-Zeitschrift & Zeitschrift für Polymere · doi:10.1007/bf01500379 · Cited by 255
Research works printed but not linked: 7
- Haward R., 1968, Proc. R. Soc. A, 302, 453
- Takahashi Y., 1988, Part B: Polym. Phys
- Bridgman P., 1944, Trans. Am. Soc. Met., 32, 553
- Hiss, R. Ph.D. Thesis, Freiburg, 1996.
- Gauthier C., 10th International Conference on Deformation, Yield and Fracture of Polymers; Institute of Materials: London
- Krigas T., 1985, J. Polym. Sci., 23, 509
- Kelly A., 1970, Crystallography of Crystal Defects
Cited by
Strobl, G. (2006) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2006.01.001 · Cited by 486
“The blocky substructure is fundamental for the deformation properties of semicrystalline polymers [34, 35 ].”
BackgroundSelf-citationRole of the Entangled Amorphous Network in Tensile Deformation of Semicrystalline Polymers
Men, Y., Rieger, J., & Strobl, G. (2003) · Physical Review Letters · doi:10.1103/physrevlett.91.095502 · Cited by 428
Self-citationChain Dimensions and Entanglement Spacings
Fetters, L. J., Lohse, D. J., & Colby, R. H. (2007) · Physical Properties of Polymers Handbook · doi:10.1007/978-0-387-69002-5_25 · Cited by 376
Cavitation during deformation of semicrystalline polymers
Pawlak, A., Galeski, A., & Rozanski, A. (2014) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2013.10.007 · Cited by 355
Plastic Deformation of Crystalline Polymers: The Role of Cavitation and Crystal Plasticity
Pawlak, A., & Galeski, A. (2005) · Macromolecules · doi:10.1021/ma050842o · Cited by 314
Micromechanical modeling of the elasto-viscoplastic behavior of semi-crystalline polymers
VANDOMMELEN, J., PARKS, D., BOYCE, M., BREKELMANS, W., & BAAIJENS, F. (2003) · Journal of the Mechanics and Physics of Solids · doi:10.1016/s0022-5096(02)00063-7 · Cited by 268
“For polyethylene, commonly a hysteresis loop is found during unloading and subsequent reloading (Sargent and Shinozaki, 1977; Hiss et al. 1999).”
BackgroundResultIntrinsic Deformation Behavior of Semicrystalline Polymers
Schrauwen, B. A. G., Janssen, R. P. M., Govaert, L. E., & Meijer, H. E. H. (2004) · Macromolecules · doi:10.1021/ma035279t · Cited by 265
Cavitation during Tensile Deformation of Polypropylene
Pawlak, A., & Galeski, A. (2008) · Macromolecules · doi:10.1021/ma0715122 · Cited by 216
Chemicapacitive microsensors for volatile organic compound detection
Patel, S. V., Mlsna, T. E., Fruhberger, B., Klaassen, E., Cemalovic, S., & Baselt, D. R. (2003) · Sensors and Actuators B: Chemical · doi:10.1016/s0925-4005(03)00637-3 · Cited by 203
Deformation-Induced Color Changes in Mechanochromic Polyethylene Blends
Crenshaw, B. R., Burnworth, M., Khariwala, D., Hiltner, A., Mather, P. T., Simha, R., & Weder, C. (2007) · Macromolecules · doi:10.1021/ma062936j · Cited by 198
Zuo, F., Keum, J. K., Chen, X., Hsiao, B. S., Chen, H., Lai, S.-Y., Wevers, R., & Li, J. (2007) · Polymer · doi:10.1016/j.polymer.2007.08.065 · Cited by 197
Hong, K., Rastogi, A., & Strobl, G. (2004) · Macromolecules · doi:10.1021/ma049174h · Cited by 192
Self-citationHobeika, S., Men, Y., & Strobl, G. (2000) · Macromolecules · doi:10.1021/ma9910484 · Cited by 183
Self-citationMechanical Properties of Low Density Polyethylene
Jordan, J. L., Casem, D. T., Bradley, J. M., Dwivedi, A. K., Brown, E. N., & Jordan, C. W. (2016) · Journal of Dynamic Behavior of Materials · doi:10.1007/s40870-016-0076-0 · Cited by 165
“These materials can be thought of as molecular networks consisting of an amorphous phase containing entangled chains with the randomly oriented crystallite phase acting as physical crosslinks [2–4].”
BackgroundAddiego, F., Dahoun, A., G'Sell, C., & Hiver, J.-M. (2006) · Polymer · doi:10.1016/j.polymer.2006.03.093 · Cited by 177
Séguéla, R. (2007) · Macromolecular Materials and Engineering · doi:10.1002/mame.200600389 · Cited by 165
Fatigue analysis of FDM materials
Lee, J., & Huang, A. (2013) · Rapid Prototyping Journal · doi:10.1108/13552541311323290 · Cited by 161
Xu, S., Zhou, J., & Pan, P. (2023) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2023.101676 · Cited by 166
Cavitation during tensile deformation of high-density polyethylene
Pawlak, A. (2007) · Polymer · doi:10.1016/j.polymer.2006.12.054 · Cited by 162
Crosslinked poly (vinyl alcohol): Structural, optical and mechanical properties
Sau, S., Pandit, S., & Kundu, S. (2021) · Surfaces and Interfaces · doi:10.1016/j.surfin.2021.101198 · Cited by 160
Krishnaswamy, R. K., Yang, Q., Fernandez-Ballester, L., & Kornfield, J. A. (2008) · Macromolecules · doi:10.1021/ma070454h · Cited by 159
Jiang, Z., Tang, Y., Men, Y., Enderle, H., Lilge, D., Roth, S. V., Gehrke, R., & Rieger, J. (2007) · Macromolecules · doi:10.1021/ma0627572 · Cited by 158
Jiang, Z., Tang, Y., Rieger, J., Enderle, H., Lilge, D., Roth, S. V., Gehrke, R., Wu, Z., Li, Z., & Men, Y. (2009) · Polymer · doi:10.1016/j.polymer.2009.06.063 · Cited by 156
Reinforcement in melt-processed polymer–graphene composites at extremely low graphene loading level
Istrate, O. M., Paton, K. R., Khan, U., O’Neill, A., Bell, A. P., & Coleman, J. N. (2014) · Carbon · doi:10.1016/j.carbon.2014.06.077 · Cited by 155
“Fibrillation indicates slips within the crystalline lamellae and changes in the chain direction [47].”
BackgroundTwo Lamellar to Fibrillar Transitions in the Tensile Deformation of High-Density Polyethylene
Jiang, Z., Tang, Y., Rieger, J., Enderle, H., Lilge, D., Roth, S. V., Gehrke, R., Heckmann, W., & Men, Y. (2010) · Macromolecules · doi:10.1021/ma100303d · Cited by 153
Parodi, E., Peters, G. G., & Govaert, L. E. (2017) · Journal of Applied Polymer Science · doi:10.1002/app.45942 · Cited by 157
Plasticity of semicrystalline polymers
Bartczak, Z., & Galeski, A. (2010) · Macromolecular Symposia · doi:10.1002/masy.201050807 · Cited by 150
Hedesiu, C., Demco, D. E., Kleppinger, R., Adams, A., Blümich, B., Remerie, K., & Litvinov, V. M. (2006) · Polymer · doi:10.1016/j.polymer.2006.12.019 · Cited by 139
Kurelec, L., Teeuwen, M., Schoffeleers, H. M., & Deblieck, R. A. C. (2005) · Polymer · doi:10.1016/j.polymer.2005.05.061 · Cited by 153
Tian, H., Xu, G., Yang, B., & Guo, G. (2011) · Journal of Food Engineering · doi:10.1016/j.jfoodeng.2011.06.008 · Cited by 122
Cavitation‐Induced Stress Whitening in Semi‐Crystalline Polymers
Lu, Y., & Men, Y. (2018) · Macromolecular Materials and Engineering · doi:10.1002/mame.201800203 · Cited by 121
Effect of chain entanglements on plastic deformation behavior of linear polyethylene
Bartczak, Z. (2005) · Macromolecules · doi:10.1021/ma050815y · Cited by 116
Synchrotron Ultrasmall-Angle X-ray Scattering Studies on Tensile Deformation of Poly(1-butene)
Men, Y., Rieger, J., & Homeyer, J. (2004) · Macromolecules · doi:10.1021/ma048274k · Cited by 116
The Entanglements of Macromolecules and Their Influence on the Properties of Polymers
Pawlak, A. (2019) · Macromolecular Chemistry and Physics · doi:10.1002/macp.201900043 · Cited by 117
Critical Strains Determine the Tensile Deformation Mechanism in Semicrystalline Polymers
Men, Y. (2020) · Macromolecules · doi:10.1021/acs.macromol.0c02076 · Cited by 117
Bartczak, Z., & Kozanecki, M. (2005) · Polymer · doi:10.1016/j.polymer.2005.06.100 · Cited by 108
Zhang, X., Schneider, K., Liu, G., Chen, J., Brüning, K., Wang, D., & Stamm, M. (2011) · Polymer · doi:10.1016/j.polymer.2011.07.003 · Cited by 108
Tensile Deformation of Polybutene-1 with Stable Form I at Elevated Temperature
Wang, Y., Jiang, Z., Wu, Z., & Men, Y. (2012) · Macromolecules · doi:10.1021/ma302389j · Cited by 107
CRITICAL STRAINS DETERMINING THE YIELD BEHAVIOR OF s-PP*
Men, Y., & Strobl, G. R. (2001) · Journal of Macromolecular Science Part B · doi:10.1081/mb-100107561 · Cited by 107
“In spite of the large changes in the mechanical properties from solid- to rubberlike when decreasing the crystallinity [5] or of the variations in the necessary forces with temperature and strain rate [6], it was found that the critical strains remained constant.”
BackgroundMethodInfluentialSelf-citationCavitation and morphological changes in polypropylene deformed at elevated temperatures
Pawlak, A., & Gałęski, A. (2010) · Journal of Polymer Science Part B Polymer Physics · doi:10.1002/polb.22020 · Cited by 102
Reversible Lamellar Thickening Induced by Crystal Transition in Poly(butylene succinate)
Liu, G., Zheng, L., Zhang, X., Li, C., Jiang, S., & Wang, D. (2012) · Macromolecules · doi:10.1021/ma300530a · Cited by 102
Men, Y., & Strobl, G. R. (2003) · Macromolecules · doi:10.1021/ma025955b · Cited by 100
Self-citationZhu, P., Dong, X., & Wang, D. (2017) · Macromolecules · doi:10.1021/acs.macromol.6b02747 · Cited by 92
Mahmud, M. B., Anstey, A., Shaayegan, V., Lee, P., & Park, C. B. (2020) · Composites Part B Engineering · doi:10.1016/j.compositesb.2020.108067 · Cited by 90
Structural mechanics of semicrystalline polymers prior to the yield point: a review
Патлажан, С. А., & Rémond, Y. (2012) · Journal of Materials Science · doi:10.1007/s10853-012-6620-y · Cited by 96
Fu, Q., Men, Y., & Strobl, G. R. (2003) · Polymer · doi:10.1016/s0032-3861(02)00940-0 · Cited by 96
Self-citationAl‐Hussein, M., & Strobl, G. R. (2002) · Macromolecules · doi:10.1021/ma020831k · Cited by 88
Self-citationCavitation during tensile drawing of annealed high density polyethylene
Pawlak, A., & Gałęski, A. (2010) · Polymer · doi:10.1016/j.polymer.2010.10.003 · Cited by 87
Bruno Fayolle, C., Audouin, L., & Jacques Verdu, C. (2004) · Polymer · doi:10.1016/j.polymer.2004.03.069 · Cited by 87
Nozue, Y., Shinohara, Y., Ogawa, Y., Sakurai, T., Hori, H., Kasahara, T., Yamaguchi, N., Yagi, N., & Amemiya, Y. (2007) · Macromolecules · doi:10.1021/ma061924v · Cited by 85
Thermo-molded wheat gluten plastics plasticized with glycerol: Effect of molding temperature
Sun, S., Song, Y., & Zheng, Q. (2007) · Food Hydrocolloids · doi:10.1016/j.foodhyd.2007.05.012 · Cited by 84
Ying, Z., Wu, D., Zhang, M., & Qiu, Y. (2017) · Composite Structures · doi:10.1016/j.compstruct.2017.06.042 · Cited by 86
Belle, A. V., Demets, R., Mys, N., Kets, K. V., Dewulf, J. P., Geem, K. M. V., Meester, S. D., & Ragaert, K. (2020) · Polymers · doi:10.3390/polym12051171 · Cited by 83
Stretching Isotactic Polypropylene: From “cross-β” to Crosshatches, from γ Form to α Form
Auriemma, F., & Rosa, C. D. (2006) · Macromolecules · doi:10.1021/ma0609127 · Cited by 83
Zhang, X., Schneider, K., Liu, G., Chen, J., Brüning, K., Wang, D., & Stamm, M. (2011) · Polymer · doi:10.1016/j.polymer.2011.12.002 · Cited by 82
Quantification of strain-induced damage in semi-crystalline polymers: a review
Zhang, Y., Jar, P. ‐. B., Xue, S., & Li, L. (2018) · Journal of Materials Science · doi:10.1007/s10853-018-2859-2 · Cited by 82
Wang, Y., Jiang, Z., Fu, L., Lu, Y., & Men, Y. (2013) · Macromolecules · doi:10.1021/ma401326g · Cited by 80
Mechanical α-Process in Polyethylene
Men, Y., Rieger, J., Endeler, H.-F., & Lilge, D. (2003) · Macromolecules · doi:10.1021/ma0344902 · Cited by 79
Thermo-viscoelastic and viscoplastic behavior of high-density polyethylene
Drozdov, A. D., & Christiansen, J. D. C. (2008) · International Journal of Solids and Structures · doi:10.1016/j.ijsolstr.2008.03.008 · Cited by 78
Lamellar Thickness and Stretching Temperature Dependency of Cavitation in Semicrystalline Polymers
Wang, Y., Jiang, Z., Fu, L., Lu, Y., & Men, Y. (2014) · PLoS ONE · doi:10.1371/journal.pone.0097234 · Cited by 77
“The result of such block slips yields a successive decrease of the orientational order parameter of crystallographic (110) plane indicating a preferential orientation of polymer chains in the crystalline phase towards stretching direction [22].”
BackgroundSahputra, I. H., & Echtermeyer, A. T. (2013) · Modelling and Simulation in Materials Science and Engineering · doi:10.1088/0965-0393/21/6/065016 · Cited by 76
Pawlak, A., & Krajenta, J. (2024) · Molecules · doi:10.3390/molecules29143410 · Cited by 80
“The entanglements act as physical cross-links, equivalent to chemical cross-links in rubber [4].”
BackgroundWang, D., Shao, C., Zhao, B., Bai, L., Wang, X., Yan, T., Li, J., Pan, G., & Li, L. (2010) · Macromolecules · doi:10.1021/ma1000282 · Cited by 75
Hong, K., & Strobl, G. R. (2005) · Macromolecules · doi:10.1021/ma051726o · Cited by 76
Self-citationNikolov, S., Lebensohn, R. A., & Raabe, D. (2006) · Journal of the Mechanics and Physics of Solids · doi:10.1016/j.jmps.2006.01.008 · Cited by 85
Pierro, I., Zanchin, G., Parisini, E., Martí‐Rujas, J., Canetti, M., Ricci, G., Bertini, F., & Leone, G. (2018) · Macromolecules · doi:10.1021/acs.macromol.7b02242 · Cited by 76
Burns, A. B., & Register, R. A. (2016) · Macromolecules · doi:10.1021/acs.macromol.6b02175 · Cited by 73
Liu, Z., Liu, X., Zheng, G., Dai, K., Liu, C., Shen, C., Yin, R., & Guo, Z. (2017) · Polymer Testing · doi:10.1016/j.polymertesting.2017.01.002 · Cited by 72
Structure Evolution and Deformation Behavior of Polyethylene Film during Biaxial Stretching
Chen, Q., Wang, Z., Zhang, S., Cao, Y. Q., & Chen, J. (2019) · ACS Omega · doi:10.1021/acsomega.9b03250 · Cited by 71
Wang, Z., An, M., Xu, H., Lv, Y., Tian, F., & Gu, Q. (2017) · Polymer · doi:10.1016/j.polymer.2017.05.062 · Cited by 71
Scratch deformation behavior of thermoplastic materials with significant differences in ductility
Hadal, R. S., & Misra, R. D. K. (2005) · Materials Science and Engineering A · doi:10.1016/j.msea.2005.03.028 · Cited by 70
Hsueh, H.-C., Kim, J. H., Orski, S. V., Fairbrother, A., Jacobs, D., Perry, L. N., Hunston, D. L., White, C. C., & Sung, L. (2020) · Polymer Degradation and Stability · doi:10.1016/j.polymdegradstab.2020.109098 · Cited by 73
Chen, X., Lv, F., Su, F., Ji, Y., Meng, L., Wan, C., Lin, Y., Li, X., & Li, L. (2017) · Polymer · doi:10.1016/j.polymer.2017.04.054 · Cited by 68
Qiu, Y., Wang, J., Wu, D., Wang, Z., Zhang, M., Yao, Y., & Wei, N. (2016) · Composites Science and Technology · doi:10.1016/j.compscitech.2016.07.005 · Cited by 67
Crystalline Lamellae Fragmentation during Drawing of Polypropylene
Różański, A., & Gałęski, A. (2015) · Macromolecules · doi:10.1021/acs.macromol.5b01180 · Cited by 64
Zheng, L., Liu, L., Shao, C., Wang, W., Wang, B., Pan, L., Li, Y., & Ma, Z. (2019) · Macromolecules · doi:10.1021/acs.macromol.8b02600 · Cited by 65
SAXS Studies on Structural Changes in a Poly(vinyl alcohol) Film during Uniaxial Stretching in Water
Miyazaki, T., Hoshiko, A., Akasaka, M., Shintani, T., & Sakurai, S. (2006) · Macromolecules · doi:10.1021/ma052595u · Cited by 65
Mechanical recycling of printed flexible plastic packaging: The role of binders and pigments
Lisiecki, M., Lisiecki, M., Belé, T. G. A., Belé, T. G. A., Üǧdüler, S., Fiório, R., Astrup, T. F., Astrup, T. F., Meester, S. D., & Ragaert, K. (2024) · Journal of Hazardous Materials · doi:10.1016/j.jhazmat.2024.134375 · Cited by 64
Wang, L., Dong, X., Huang, M., & Wang, D. (2016) · Polymer · doi:10.1016/j.polymer.2016.05.038 · Cited by 64
Hong, K., Rastogi, A., & Strobl, G. R. (2004) · Macromolecules · doi:10.1021/ma049172x · Cited by 64
Self-citationWu, H., Nikzad, S., Zhu, C., Yan, H., Li, Y., Niu, W., Matthews, J. R., Xu, J., Matsuhisa, N., Arunachala, P. K., et al. (2023) · Nature Communications · doi:10.1038/s41467-023-44099-w · Cited by 62
Litvinov, V. M., Deblieck, R. A. C., Clair, C., den Fonteyne, W. V., Lallam, A., Kleppinger, R., Ivanov, D. A., Ries, M. E., & Boerakker, M. J. (2020) · Macromolecules · doi:10.1021/acs.macromol.0c00956 · Cited by 63
Bartczak, Z. (2010) · Journal of Polymer Science Part B: Polymer Physics · doi:10.1002/polb.21873 · Cited by 60
Zhou, J., Zheng, Y., Shan, G., Bao, Y., Wang, W., & Pan, P. (2019) · Macromolecules · doi:10.1021/acs.macromol.8b02011 · Cited by 59
Viana, J. C. (2005) · Polymer · doi:10.1016/j.polymer.2005.10.024 · Cited by 58
Kiass, N., Khelif, R., Boulanouar, L., & Chaoui, K. (2005) · Journal of Applied Polymer Science · doi:10.1002/app.21713 · Cited by 57
Strain hardening of high density polyethylene
Haward, R. N. (2007) · Journal of Polymer Science Part B Polymer Physics · doi:10.1002/polb.21123 · Cited by 60
Micromechanics of semicrystalline polymers: Yield kinetics and long‐term failure
Sedighiamiri, A., Govaert, L. E., Kanters, M. J. W., & van Dommelen, J. A. W. (2012) · Journal of Polymer Science Part B Polymer Physics · doi:10.1002/polb.23136 · Cited by 65
Xiong, B., Lame, O., Chenal, J., Rochas, C., Séguéla, R., & Vigier, G. (2015) · Macromolecules · doi:10.1021/acs.macromol.5b01258 · Cited by 57
Morphology and Plastic Yielding of Ultrahigh Molecular Weight Polyethylene
Gałęski, A., Bartczak, Z., Vozniak, A., Pawlak, A., & Walkenhorst, R. (2020) · Macromolecules · doi:10.1021/acs.macromol.9b02154 · Cited by 58
A constitutive description of the rate-sensitive response of semi-crystalline polymers
Pouriayevali, H., Arabnejad, S., Guo, Y., & Shim, V. P. W. (2013) · International Journal of Impact Engineering · doi:10.1016/j.ijimpeng.2013.05.002 · Cited by 61
Bao, R., Ding, Z., Zhong, G., Yang, W. M., Xie, B., & Yang, M. (2011) · Colloid & Polymer Science · doi:10.1007/s00396-011-2550-5 · Cited by 56
Chang, B., Schneider, K., Xiang, F., Vogel, R., Roth, S. V., & Heinrich, G. (2018) · Macromolecules · doi:10.1021/acs.macromol.8b00642 · Cited by 56
Cyclic tensile properties of the polylactide nanocomposite foams containing cellulose nanocrystals
Qiu, Y., Lv, Q., Wu, D., Xie, W., Peng, S., Lan, R., & Xie, H. (2018) · Cellulose · doi:10.1007/s10570-018-1703-9 · Cited by 55
“According to Strobl’s approach (Hiss et al. 1999), the maximum true strain in each cycle as the sum of an elastic component eH;e and a plastic component eH;p can then be calculated, and the results are shown in Fig.”
BackgroundMethodZhu, T., Li, X., Zhao, X., Zhang, X., Lu, Y., & Zhang, L. (2021) · Polymer Testing · doi:10.1016/j.polymertesting.2021.107460 · Cited by 54
Rosa, C. D., Auriemma, F., & de Ballesteros, O. R. (2006) · Physical Review Letters · doi:10.1103/physrevlett.96.167801 · Cited by 54
Wu, J., Wu, X., Yang, F., Liu, X., Meng, F., Ma, Q., & Che, Y. (2022) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2022.11.173 · Cited by 53
Xiong, B., Kang, J., Chen, R., & Men, Y. (2017) · Polymer · doi:10.1016/j.polymer.2017.09.017 · Cited by 53
Parodi, E., Peters, G. G., & Govaert, L. E. (2018) · Polymers · doi:10.3390/polym10070710 · Cited by 60
Micromechanical modeling of the deformation kinetics of semicrystalline polymers
Sedighiamiri, A., Govaert, L. E., & van Dommelen, J. A. W. (2011) · Journal of Polymer Science Part B Polymer Physics · doi:10.1002/polb.22297 · Cited by 54
Metadata
- Authors
- Hiss, R., Hobeika, S., Lynn, C., & Strobl, G.
- Affiliations
- University of Freiburg (DE)
- Venue
- Macromolecules
- Publisher
- American Chemical Society (ACS)
- Published
- 1999-06-01
- Volume
- 32
- Issue
- 13
- Pages
- 4390-4403
- ISSN
- 0024-9297 (ISSN-L)
- 1520-5835
- OpenAlex
- W1964100411
- Semantic Scholar
- 001144c6520c7f808e72de547a96271a0ae7d26f
- Cited by
- 540
- References
- 32
- Citations by year
- 2026: 25 · 2025: 23 · 2024: 29 · 2023: 23 · 2022: 19 · 2021: 26 · 2020: 23 · 2019: 27 · 2018: 40 · 2017: 29 · 2016: 19 · 2015: 15 · 2014: 18 · 2013: 24 · 2012: 22
- FWCI
- 7.41
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- Macromolecules (publishedVersion)
- FreiDok plus (Universitätsbibliothek Freiburg) (submittedVersion)
- Topics
- Physical Sciences › Materials Science › Polymers and Plastics › Polymer crystallization and properties
- Physical Sciences › Materials Science › Metals and Alloys › Microstructure and mechanical properties
- Physical Sciences › Chemical Engineering › Fluid Flow and Transfer Processes › Rheology and Fluid Dynamics Studies
- Keywords
- polyethylene, low-density polyethylene, uniaxial drawing, chain disentanglement, crystallinity, necking, true stress-strain curves, crystallographic texture, irreversible deformation
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.