Three-dimensional analysis of Nafion layers in fuel cell electrodes
Open accessThe DOI matches its Crossref record; 31 of the 32 references it cites were found in a registry or an index.
Abstract
Proton exchange membrane fuel cell is one of the most promising zero-emission power sources for automotive or stationary applications. However, their cost and lifetime remain the two major key issues for a widespread commercialization. Consequently, much attention has been devoted to optimizing the membrane/electrode assembly that constitute the fuel cell core. The electrodes consist of carbon black supporting Pt nanoparticles and Nafion as the ionomer binder. Although the ionomer plays a crucial role as ionic conductor through the electrode, little is known about its distribution inside the electrode. Here we report the three-dimensional morphology of the Nafion thin layer surrounding the carbon particles, which is imaged using electron tomography. The analyses reveal that doubling the amount of Nafion in the electrode leads to a twofold increase in its degree of coverage of the carbon, while the thickness of the layer, around 7 nm, is unchanged.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“The distribution of ionomer in CLs is usually inhomogeneous, in the sense that the coverage of Pt nanoparticles can be categorized as (i) fully covered with a thick ionomer film, (ii) fully covered with a thin ionomer film, (iii) partially covered by ionomer, and (iv) completely uncovered by ionomer [45].”
From Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells (2022) · cites this paper as [45]
Experimental — accuracy not yet measured
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Materials for fuel-cell technologies
Steele, B. C. H., & Heinzel, A. (2001) · Nature · doi:10.1038/35104620 · Cited by 7,772
Electrocatalyst approaches and challenges for automotive fuel cells
Debe, M. K. (2012) · Nature · doi:10.1038/nature11115 · Cited by 5,885
Alloys of platinum and early transition metals as oxygen reduction electrocatalysts
Greeley, J., Stephens, I. E. L., Bondarenko, A. S., Johansson, T. P., Hansen, H. A., Jaramillo, T. F., Rossmeisl, J., Chorkendorff, I., & Nørskov, J. K. (2009) · Nature Chemistry · doi:10.1038/nchem.367 · Cited by 3,203
Litster, S., & McLean, G. (2004) · Journal of Power Sources · doi:10.1016/j.jpowsour.2003.12.055 · Cited by 1,275
Electron tomography and holography in materials science
Midgley, P. A., & Dunin-Borkowski, R. E. (2009) · Nature Materials · doi:10.1038/nmat2406 · Cited by 883
Chemically sensitive structure-imaging with a scanning transmission electron microscope
Pennycook, S. J., & Boatner, L. A. (1988) · Nature · doi:10.1038/336565a0 · Cited by 735
The effect of three-dimensional morphology on the efficiency of hybrid polymer solar cells
Oosterhout, S. D., Wienk, M. M., van Bavel, S. S., Thiedmann, R., Jan Anton Koster, L., Gilot, J., Loos, J., Schmidt, V., & Janssen, R. A. J. (2009) · Nature Materials · doi:10.1038/nmat2533 · Cited by 531
Electron Tomography for Heterogeneous Catalysts and Related Nanostructured Materials
Friedrich, H., de Jongh, P. E., Verkleij, A. J., & de Jong, K. P. (2009) · Chemical Reviews · doi:10.1021/cr800434t · Cited by 256
Measuring oxygen reduction/evolution reactions on the nanoscale
Kumar, A., Ciucci, F., Morozovska, A. N., Kalinin, S. V., & Jesse, S. (2011) · Nature Chemistry · doi:10.1038/nchem.1112 · Cited by 241
3D Imaging of Catalyst Support Corrosion in Polymer Electrolyte Fuel Cells
Schulenburg, H., Schwanitz, B., Linse, N., Scherer, G. G., Wokaun, A., Krbanjevic, J., Grothausmann, R., & Manke, I. (2011) · The Journal of Physical Chemistry C · doi:10.1021/jp203016u · Cited by 229
Research works printed but not linked: 1
- Martin, C. W., Baker, S. H., Gordon, T. D. & Davila, M. Processes for forming thin, durable coatings of cation-containing polymers on selected substrates. US Patent 5.718,947 (1998).
Cited by
Items 101–200 of 435
Li, J., Ma, Q., Dong, S., Zhao, S. Z., Wang, B., & Feng, X. (2025) · Chemical Society Reviews · doi:10.1039/d5cs00604j · Cited by 49
Shim, H. K., Paul, D. K., & Karan, K. (2015) · Macromolecules · doi:10.1021/acs.macromol.5b02093 · Cited by 49
Berlinger, S. A., Chowdhury, A., Cleve, T. V., He, A., Dagan, N., Neyerlin, K. C., McCloskey, B. D., Radke, C. J., & Weber, A. Z. (2022) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.2c10499 · Cited by 49
Fang, S., Liu, G., Li, M., Zhang, H., Yu, J., Zhang, F., Pan, M., & Tang, H. (2023) · ACS Applied Energy Materials · doi:10.1021/acsaem.3c00193 · Cited by 48
The impact of different side chain ionomer on membrane electrode assembly performance and durability
Liu, S., Lin, R., Lu, J., Wang, Y., & Cai, X. L. (2023) · Chemical Engineering Journal · doi:10.1016/j.cej.2023.145050 · Cited by 48
Correlative X-ray Tomographic Imaging of Catalyst Layer Degradation in Fuel Cells
White, R., Ramani, D., Eberhardt, S. H., Najm, M., Orfino, F. P., Dutta, M., & Kjeang, E. (2019) · Journal of The Electrochemical Society · doi:10.1149/2.0121913jes · Cited by 46
Wu, J., Zhu, X., West, M. M., Tyliszczak, T., Shiu, H., Shapiro, D. A., Berejnov, V., Susac, D., Stumper, J., & Hitchcock, A. P. (2018) · The Journal of Physical Chemistry C · doi:10.1021/acs.jpcc.8b02933 · Cited by 45
Lin, X., Zalitis, C. M., Sharman, J. D. B., & Kucernak, A. R. (2020) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.0c12718 · Cited by 45
Impact of Nonadsorbed Ionomer on Viscosity of Catalyst Inks for Polymer Electrolyte Fuel Cells
Yoshimune, W., & Harada, M. (2020) · Bulletin of the Chemical Society of Japan · doi:10.1246/bcsj.20190321 · Cited by 44
Effects of Ionomer Carbon Ratio and Ionomer Dispersity on the Performance and Durability of MEAs
Lee, M. ‐., Lee, H. ‐., Yim, S. ‐., Kim, C. ‐., Shul, Y. ‐., Kucernak, A., & Shin, D. (2018) · Fuel Cells · doi:10.1002/fuce.201700178 · Cited by 44
Impact of the Solid Interface on Proton Conductivity in Nafion Thin Films
Ogata, Y., Abe, T., Yonemori, S., Yamada, N. L., Kawaguchi, D., & Tanaka, K. (2018) · Langmuir · doi:10.1021/acs.langmuir.8b03396 · Cited by 44
Poojary, S., Islam, M. N., Shrivastava, U. N., Roberts, E. P. L., & Karan, K. (2020) · Molecules · doi:10.3390/molecules25153387 · Cited by 43
Chen, Y., Zhong, Q. D., Li, G., Tian, T., Tan, J., & Pan, M. (2018) · Ionics · doi:10.1007/s11581-018-2533-3 · Cited by 42
“We found that the theoretical thickness of Nafion does not exceed 10 nm even at over region, which is not consistent with the thickness of the observed Nafion on the real catalyst surface [23].”
BackgroundLee, J. H., Kang, H., Yim, S., Sohn, Y.-J., & Lee, S. G. (2022) · Applied Surface Science · doi:10.1016/j.apsusc.2022.153815 · Cited by 42
Kim, H., Kwon, J., & Lee, H. (2022) · Chemical Science · doi:10.1039/d2sc00541g · Cited by 42
Venkatesan, S. V., Dutta, M., & Kjeang, E. (2016) · Electrochemistry Communications · doi:10.1016/j.elecom.2016.08.018 · Cited by 42
Mezzavilla, S., Cherevko, S., Baldizzone, C., Pizzutilo, E., Polymeros, G., & Mayrhofer, K. J. J. (2016) · ChemElectroChem · doi:10.1002/celc.201600170 · Cited by 41
Improving Oxygen Reduction Performance by Using Protic Poly(Ionic Liquid) as Proton Conductors
Yan, X., Zhang, F., Zhang, H., Tang, H., Pan, M., & Fang, P. (2019) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.8b20587 · Cited by 41
Chowdhury, A., Bird, A., Liu, J., Zenyuk, I. V., Kusoglu, A., Radke, C. J., & Weber, A. Z. (2021) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.1c07611 · Cited by 40
Sun, F., Di, Q., Chen, M., Liu, H., & Wang, H. (2024) · eTransportation · doi:10.1016/j.etran.2024.100327 · Cited by 40
Lee, J., Escribano, S., Micoud, F., Gebel, G., Lyonnard, S., Porcar, L., Martínez, N., & Morin, A. (2020) · ACS Applied Energy Materials · doi:10.1021/acsaem.0c00853 · Cited by 39
Self-citationOptimized mass transfer in a Pt-based cathode catalyst layer for PEM fuel cells
Wang, M., Teng, J., Zaman, S., Zhang, S., Chen, X., Zhang, K., Wang, X., Li, Z., & Wu, M. (2024) · Green Chemistry · doi:10.1039/d3gc05033e · Cited by 38
Li, H., You, J., Feng, Y., Yan, X., Yin, J., Luo, L., He, M., Cheng, X., Shen, S., & Zhang, J. (2023) · Chemical Engineering Journal · doi:10.1016/j.cej.2023.147454 · Cited by 38
Salarizadeh, P., Javanbakht, M., Askari, M. B., Hooshyari, K., Moradi, M., Beydaghi, H., Rastgoo‐Deylami, M., & Enhessari, M. (2021) · Scientific Reports · doi:10.1038/s41598-021-84321-7 · Cited by 37
Mechanical Behavior of Free-Standing Fuel Cell Electrodes on Water Surface
Kim, S., Kim, J.-H., Oh, J., Jang, K.-L., Jeong, B., Hong, B. K., & Kim, T. (2016) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.6b03854 · Cited by 36
Dou, S., Hao, L., & Liu, H. (2023) · Renewable Energy · doi:10.1016/j.renene.2023.119254 · Cited by 36
Morawietz, T., Handl, M., Oldani, C., Friedrich, K. A., & Hiesgen, R. (2018) · Fuel Cells · doi:10.1002/fuce.201700113 · Cited by 36
Proton-Exchange Membrane Fuel Cells with Low-Pt Content
Kongkanand, A., Gu, W., & Mathias, M. F. (2018) · Springer eBooks · doi:10.1007/978-1-4939-7789-5_1022 · Cited by 35
Kakati, N., Anderson, L. O., Li, G., Sua-an, D. M., Karmakar, A., Ocon, J. D., & Chuang, P. A. (2023) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.3c08377 · Cited by 35
Hou, Y., Liu, H., Han, J., Cai, W., Zhou, J. Z., Wang, A., & Cheng, H.-Y. (2016) · ACS Sustainable Chemistry & Engineering · doi:10.1021/acssuschemeng.6b00647 · Cited by 35
Fu, K., Tian, T., Chen, Y., Li, S., Cai, C., Zhang, Y., Guo, W., & Pan, M. (2018) · International Journal of Energy Research · doi:10.1002/er.4283 · Cited by 35
Ceramic Lithium Ion Conductor to Solve the Anode Coking Problem of Practical Solid Oxide Fuel Cells
Wang, W., Wang, F., Chen, Y., Qu, J., Tadé, M. O., & Shao, Z. (2015) · ChemSusChem · doi:10.1002/cssc.201500028 · Cited by 34
Huang, X., He, Y., Sun, Y., Sun, L., Wang, T., & Zhang, X. (2024) · Journal of Power Sources · doi:10.1016/j.jpowsour.2024.234488 · Cited by 34
Melo, L. G. A., Hitchcock, A. P., Berejnov, V., Susac, D., Stumper, J., & Botton, G. A. (2016) · Journal of Power Sources · doi:10.1016/j.jpowsour.2016.02.019 · Cited by 34
Theory of electrostatic phenomena in water-filled Pt nanopores
Huang, J., Zhang, J., & Eikerling, M. H. (2016) · Faraday Discussions · doi:10.1039/c6fd00094k · Cited by 34
Zhang, R., Chen, L., Min, T., Mu, Y., Hao, L., & Tao, W. (2024) · Carbon Neutrality · doi:10.1007/s43979-024-00089-5 · Cited by 33
“1(a), it is widely observed that the CL consists of overlapping carbon particles, the Pt particles loaded on the carbon surface, thin ionomer film covered on the Pt/ carbon structures, and pores [12, 29–31].”
InfluentialRegulating catalyst and ionomer interactions to promote oxygen transport in fuel cells
Wang, M., Zhang, S., Wang, H., Sun, E., Liu, D., Wu, M., Liu, D., & Li, Z. (2024) · Applied Catalysis B: Environmental · doi:10.1016/j.apcatb.2024.124894 · Cited by 33
Mabuchi, T., Huang, S.-F., & Tokumasu, T. (2020) · Macromolecules · doi:10.1021/acs.macromol.0c01303 · Cited by 33
Hrnjić, A., Kamšek, A. R., Bijelić, L., Logar, A., Maselj, N., Smiljanić, M., Trputec, J., Vovk, N., Pavko, L., Ruiz‐Zepeda, F., et al. (2024) · ACS Catalysis · doi:10.1021/acscatal.3c03883 · Cited by 33
Imaging ionomer in fuel cell catalyst layers with synchrotron nano transmission x-ray microscopy
Normile, S. J., & Zenyuk, I. V. (2019) · Solid State Ionics · doi:10.1016/j.ssi.2019.02.017 · Cited by 33
Kaneko, T., Yoshimoto, Y., Hori, T., Takagi, S., Ooyama, J., Terao, T., & Kinefuchi, I. (2020) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2019.119277 · Cited by 33
Mechanical Response of Thermally Annealed Nafion Thin Films
Frieberg, B. R., Page, K. A., Graybill, J. R., Walker, M. L., Stafford, C. M., Stafford, G. R., & Soles, C. L. (2016) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.6b12423 · Cited by 33
Lu, Y., Li, S., & Qi, R. (2024) · International Journal of Green Energy · doi:10.1080/15435075.2024.2335507 · Cited by 32
Yuan, S., Zhao, C., Luo, L., Fu, C., Li, H., An, L., Cheng, X., Shen, S., Yin, J., Yan, X., et al. (2024) · The Journal of Physical Chemistry Letters · doi:10.1021/acs.jpclett.4c00851 · Cited by 32
Reshetenko, T. V., & Kulikovsky, A. A. (2017) · Journal of The Electrochemical Society · doi:10.1149/2.1131714jes · Cited by 32
Meyer, Q. P.-G., Liu, S., Ching, K., Wang, Y. D., & Zhao, C. (2023) · Journal of Power Sources · doi:10.1016/j.jpowsour.2022.232539 · Cited by 31
Modeling of wetting phenomena in cathode catalyst layers for PEM fuel cells
Olbrich, W., Kadyk, T., Sauter, U., & Eikerling, M. H. (2022) · Electrochimica Acta · doi:10.1016/j.electacta.2022.140850 · Cited by 30
Ultrathin nanoporous metal electrodes facilitate high proton conduction for low-Pt PEMFCs
Shi, S., Wen, X., Sang, Q., Yin, S., Wang, K., Zhang, J., Hu, M., Yin, H., He, J., & Ding, Y. (2020) · Nano Research · doi:10.1007/s12274-020-3272-0 · Cited by 29
“To better enhance the image contrast under the electron beam, the ionomers sitting close to the carbon black (CB) supported Pt nanoparticle (Pt/C) electrocatalysts were stained with Cs ions [31].”
MethodA Particle Based Ionomer Attachment Model for a Fuel Cell Catalyst Layer
So, M., Park, K., Tsuge, Y., & Inoue, G. (2020) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/ab68d4 · Cited by 28
Zhong, X., Uebel, M., Wu, C., Rabe, M., Erbe, A., & Rohwerder, M. (2021) · ChemElectroChem · doi:10.1002/celc.202100083 · Cited by 28
Scherzer, A.-C., Schneider, P., Herring, P. K., Klingele, M., Zamel, N., & Gerteisen, D. (2022) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/ac58c2 · Cited by 28
A measure of active interfaces in supported catalysts for high-temperature reactions
Lee, S., Ha, H., Bae, K. T., Kim, S., Choi, H. S., Lee, J., Kim, J. H., Seo, J., Choi, J. S., Jo, Y., et al. (2021) · Chem · doi:10.1016/j.chempr.2021.11.024 · Cited by 28
Apoferritin Protein Amyloid Fibrils with Tunable Chirality and Polymorphism
Jurado, R., Adamčík, J., López‐Haro, M., Gonzalez‐Vera, J. A., Ruiz‐Arias, A., Sánchez‐Ferrer, A., Cuesta, R., Dominguez-Vera, J. M., Calvino, J. J., Orte, Á., et al. (2018) · Journal of the American Chemical Society · doi:10.1021/jacs.8b11418 · Cited by 28
Multiscale imaging and transport modeling for fuel cell electrodes
Janković, J., Zhang, S., Putz, A. M. V., Saha, M. S., & Susac, D. (2019) · Journal of materials research/Pratt's guide to venture capital sources · doi:10.1557/jmr.2018.458 · Cited by 28
Lee, J. H., Doo, G., Kwon, S. H., Kang, H., Choi, S., Yim, S.-D., Kim, H.-T., & Lee, S. G. (2020) · ACS Applied Polymer Materials · doi:10.1021/acsapm.0c00042 · Cited by 27
Molecular dynamics modeling in catalyst layer development for PEM fuel cell
Fan, L., Wang, J., Diaz, D. F. R., Li, L., Wang, Y., & Jiao, K. (2025) · Progress in Energy and Combustion Science · doi:10.1016/j.pecs.2025.101220 · Cited by 27
Review—Meeting Fuel Cell Catalyst Requirements for Heavy-Duty Vehicle Applications
Ramaswamy, N., Kongkanand, A., Wortman, J., & Gu, W. (2025) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/adae3b · Cited by 27
Jayawickrama, S. M., Han, Z., Kido, S., Nakashima, N., & Fujigaya, T. (2019) · Electrochimica Acta · doi:10.1016/j.electacta.2019.05.007 · Cited by 27
Goswami, N., Mistry, A. N., Grunewald, J. B., Fuller, T. F., & Mukherjee, P. P. (2020) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/ab927c · Cited by 27
Salvado, M. B., Schott, P., Guétaz, L., Gérard, M., David, T., & Bultel, Y. (2020) · Journal of Power Sources · doi:10.1016/j.jpowsour.2020.228893 · Cited by 27
Self-citationInoue, G., Park, K., So, M., Kimura, N., & Tsuge, Y. (2022) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2022.02.021 · Cited by 25
Shinozaki, K., Kajiya, S., Yamakawa, S., Hasegawa, N., Suzuki, T., Shibata, M. S., & Jinnouchi, R. (2023) · Journal of Power Sources · doi:10.1016/j.jpowsour.2023.232909 · Cited by 25
PFSA-Ionomer Adsorption to C and Pt/C Particles in Fuel-Cell Inks
Rajupet, S., Weber, A. Z., & Radke, C. J. (2025) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.5c00211 · Cited by 24
Wan, Q., He, Q., Zhang, Y., Zhang, L., Li, J., Hou, J., Zhuang, X., Ke, C., & Zhang, J. (2021) · Electrochimica Acta · doi:10.1016/j.electacta.2021.139023 · Cited by 24
Wang, H., Hua, S., Lin, R., Liu, S., Cai, X. L., Ji, W., & Tian, J. (2022) · Journal of Power Sources · doi:10.1016/j.jpowsour.2022.231793 · Cited by 24
Soleymani, A. P., Reid, M., & Janković, J. (2022) · Advanced Functional Materials · doi:10.1002/adfm.202209733 · Cited by 24
Digital Twin of a Hierarchical CO2 Electrolyzer Gas Diffusion Electrode
McLaughlin, D., Bierling, M., Mayerhöfer, B., Schmid, G., & Thiele, S. (2022) · Advanced Functional Materials · doi:10.1002/adfm.202212462 · Cited by 24
Wang, Q., Tang, F., Li, X., Zheng, J. P., Hao, L., Cui, G., & Ming, P. (2023) · Chemical Engineering Journal · doi:10.1016/j.cej.2023.142286 · Cited by 24
Shen, L., Ma, M., Zhao, Z., Tu, F., Liu, J., Xu, B., Zhang, Y., Zhao, L., Shao, G., & Wang, Z. (2023) · Journal of Power Sources · doi:10.1016/j.jpowsour.2023.233202 · Cited by 24
Study on Accelerated Stress Test for Fuel Cell Lifetime
Tian, T., Tang, J., Chen, Y., Tan, J., Li, S., & Pan, M. (2018) · International Journal of Electrochemical Science · doi:10.20964/2018.02.69 · Cited by 24
Wang, M., Peng, F., Zou, J., Zhao, W. G., Wu, M., Williams, M. C., Yu, G., & Wang, H. (2025) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2025.115707 · Cited by 23
Wang, M., Wang, Y., Zhang, S., Dai, Q., Teng, J., Wu, M., Dai, L., & Li, Z. (2025) · Advanced Functional Materials · doi:10.1002/adfm.202514280 · Cited by 23
Kaneko, T., Ooyama, J., Ohki, M., Kanesaka, H., Yoshimoto, Y., & Kinefuchi, I. (2022) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2022.123491 · Cited by 23
Xie, W., Li, X., Lin, J., Dong, L., Chen, Y., Li, N., Shi, J., Liu, J., Liu, J., Li, S., et al. (2022) · Small · doi:10.1002/smll.202205444 · Cited by 23
Multiscale characterization of polymer electrolyte fuel cells elucidated by quantum beam analysis
Yoshimune, W. (2024) · Bulletin of the Chemical Society of Japan · doi:10.1093/bulcsj/uoae046 · Cited by 23
Durable Fuel Cell Electrode Design via Efficient Distribution of the Acidic Ionomer
Ramaswamy, N., & Wortman, J. (2024) · ACS Energy Letters · doi:10.1021/acsenergylett.4c02704 · Cited by 23
Gaumont, T. (2017) · theses.fr (ABES) · doi:10.70675/5ced600dz19abz4918z941bzfd7c7dd99822 · Cited by 23
“En effet, un chargement trop important en NafionTM conduit à une diminution du volume de pore, et donc à une augmentation de la résistance au transport d’oxygène à travers la couche active [70, 71].”
BackgroundInfluentialZhang, Y., Li, X., & Klinkova, A. (2020) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2020.09.258 · Cited by 22
Lou, K., Xia, L., Friedrich, J., & Shviro, M. (2023) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2023.08.281 · Cited by 22
Su, Y., Cheng, X., Feng, Y., Li, H., Yan, C., He, M., Luo, L., Shen, S., Yan, X., & Zhang, J. (2024) · Journal of Power Sources · doi:10.1016/j.jpowsour.2024.234453 · Cited by 22
Song, J., Zhao, W., Wang, H., Meng, H., Zhang, S., Zhong, W., Wu, X., Li, M., Guan, P., Zhang, M., et al. (2024) · Chemical Engineering Journal · doi:10.1016/j.cej.2024.153971 · Cited by 22
So, M., Park, K., Ohnishi, T., Ono, M., Tsuge, Y., & Inoue, G. (2019) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2019.10.005 · Cited by 22
Shrivastava, U. N., Zhegur-Khais, A., Bass, M., Willdorf‐Cohen, S., Freger, V., Dekel, D. R., & Karan, K. (2020) · The Journal of Physical Chemistry C · doi:10.1021/acs.jpcc.0c04278 · Cited by 22
Impact of ionomer structuration on the performance of bio-inspired noble-metal-free fuel cell anodes
Coutard, N., Reuillard, B., Huan, T. N., Valentino, F., Jane, R. T., Gentil, S., Andreiadis, E. S., Goff, A. L., Asset, T., Maillard, F. M., et al. (2021) · Chem Catalysis · doi:10.1016/j.checat.2021.01.001 · Cited by 22
“4 hindering the proton conductivity in the latter.(32-33) The morphology of the clusters might be tuned through the degree of graphitization or the functionalization of carbon black,(34-35) which”
BackgroundJung, C., Choi, S.-W., Choi, W.-Y., Hong, C.-W., Jothi, V. R., & Yi, S. (2021) · Applied Catalysis B: Environmental · doi:10.1016/j.apcatb.2021.120609 · Cited by 22
Ionomeric binders in polymer electrolyte fuel cells: roles, challenges, and advances
Yu, W., Luo, F., Liang, X., Jiang, C., Xu, Y., Liu, Z., An, Q., Guiver, M. D., Wu, L., & Xu, T. (2025) · Chemical Society Reviews · doi:10.1039/d5cs00406c · Cited by 21
Wang, N., Lai, T., Wang, W., Qu, Z., Wen, X., Xie, G., & Tao, W. (2025) · eTransportation · doi:10.1016/j.etran.2025.100449 · Cited by 21
Probing nanoscale membrane degradation in fuel cells through electron tomography
Venkatesan, S. V., Hannach, M. E., Holdcroft, S., & Kjeang, E. (2017) · Journal of Membrane Science · doi:10.1016/j.memsci.2017.05.073 · Cited by 21
Performance characteristics of a liquid e-fuel cell
Shi, X., Huo, X., Esan, O. C., An, L., & Zhao, T. S. (2021) · Applied Energy · doi:10.1016/j.apenergy.2021.117145 · Cited by 21
Analysis of H2/Air Polarization Curves: The Influence of Low Pt Loading and Fabrication Process
Yu, H., Bonville, L. J., & Marić, R. (2018) · Journal of The Electrochemical Society · doi:10.1149/2.0261805jes · Cited by 21
So, S., Kang, H., Choi, D., & Oh, K.-H. (2020) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2020.05.128 · Cited by 20
Advances in Low Pt Loading Membrane Electrode Assembly for Proton Exchange Membrane Fuel Cells
Cao, F., Ding, R. F., Rui, Z., Wang, X., Meng, Z., Zhang, B., Dong, W., Li, J., Liu, J., & Jiang, X. (2023) · Molecules · doi:10.3390/molecules28020773 · Cited by 20
Arunagiri, K., Wong, A. J.-W., Briceno-Mena, L. A., Elsayed, H. M. G. H., Romagnoli, J. A., Janik, M. J., & Arges, C. G. (2023) · Energy & Environmental Science · doi:10.1039/d3ee01776a · Cited by 20
Tomographic Analysis and Modeling of Polymer Electrolyte Fuel Cell Unsupported Catalyst Layers
Ishikawa, H., Henning, S., Herranz, J. S., Eychmüller, A., Uchida, M., & Schmidt, T. J. (2018) · Journal of The Electrochemical Society · doi:10.1149/2.0371802jes · Cited by 20
Neutron imaging of operando proton exchange membrane fuel cell with novel membrane
Lee, J., Nguyen, H., Escribano, S., Micoud, F., Rosini, S., Tengattini, A., Atkins, D., Gebel, G., Iojoiu, C., Lyonnard, S., et al. (2021) · Journal of Power Sources · doi:10.1016/j.jpowsour.2021.229836 · Cited by 20
Self-citationImpact of the Cathode Layer Printing Process on the Performance of MEA Integrating PGM Free Catalyst
Toudret, P., Blachot, J.-F., Heitzmann, M., & Jacques, P.-A. (2021) · Catalysts · doi:10.3390/catal11060669 · Cited by 20
“Threshold values of ≈3–5 μm (PGM) and 60–100 μm (PGM-free) are required for the cathode active layer thickness [17,22,23] For these thick PGM-free cathodes, the active layer morphology, led by the fabrication process and the nature of the integrated catalyst, has an important impact on fuel cell performance by affecti…”
BackgroundXia, L., Tao, S., Ni, M., Wang, Y., Wu, C., Xu, Q., Dai, Y., & Cheng, C. H. (2022) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2022.08.136 · Cited by 20
Angelis, S. D., Schuler, T., Sabharwal, M., Holler, M., Guizar‐Sicairos, M., Müller, E. A., & Büchi, F. N. (2023) · Scientific Reports · doi:10.1038/s41598-023-30960-x · Cited by 20
A Comparison of Models for Transport Resistance in Fuel-Cell Catalyst Layers
Darling, R. M. (2018) · Journal of The Electrochemical Society · doi:10.1149/2.0881816jes · Cited by 20
Jang, S. A., Yoon, Y., Lee, Y., & Choi, Y. W. (2018) · Journal of Membrane Science · doi:10.1016/j.memsci.2018.06.060 · Cited by 19
Metadata
- Authors
- Lopez-Haro, M., Guétaz, L., Printemps, T., Morin, A., Escribano, S., Jouneau, P.-H., Bayle-Guillemaud, P., Chandezon, F., & Gebel, G.
- Affiliations
- Commissariat à l'Énergie Atomique et aux Énergies Alternatives (FR)
- Centre National de la Recherche Scientifique (FR)
- Corresponding author
- Chandezon, F.
- Gebel, G.
- Venue
- Nature Communications
- Published
- 2014-10-30
- Volume
- 5
- Issue
- 1
- Pages
- 5229-5229
- ISSN
- 2041-1723 (ISSN-L)
- OpenAlex
- W2082971848
- Cited by
- 402
- References
- 32
- Citations by year
- 2026: 18 · 2025: 52 · 2024: 42 · 2023: 43 · 2022: 37 · 2021: 40 · 2020: 44 · 2019: 35 · 2018: 34 · 2017: 26 · 2016: 21 · 2015: 10
- FWCI
- 10.10
- Type
- journal article
- Language
- en
- Open access
- bronze
- doi.org
- Licence
- www.springernature.com/gp/researchers/text-and-data-mining (tdm)
- www.springernature.com/gp/researchers/text-and-data-mining (vor)
- Locations
- Nature Communications (publishedVersion)
- PubMed (publishedVersion)
- HAL (submittedVersion)
- RePEc: Research Papers in Economics (submittedVersion)
- Funders
- Ministerio de Educación, Cultura y Deporte (EX2010-1135)
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Fuel Cells and Related Materials
- Physical Sciences › Energy › Renewable Energy, Sustainability and the Environment › Electrocatalysts for Energy Conversion
- Life Sciences › Biochemistry, Genetics and Molecular Biology › Structural Biology › Advanced Electron Microscopy Techniques and Applications
- Keywords
- proton exchange membrane fuel cells, Nafion, ionomer distribution, fuel cell electrodes, three-dimensional morphology, electron tomography, carbon black, platinum nanoparticles, membrane electrode assembly
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.