CoChat

Multibit memory operation of metal-oxide bi-layer memristors

Open access

The DOI matches its Crossref record; 49 of the 49 references it cites were found in a registry or an index.

Abstract

Emerging nanoionic memristive devices are considered as the memory technology of the future and have been winning a great deal of attention due to their ability to perform fast and at the expense of low-power and -space requirements. Their full potential is envisioned that can be fulfilled through their capacity to store multiple memory states per cell, which however has been constrained so far by issues affecting the long-term stability of independent states. Here, we introduce and evaluate a multitude of metal-oxide bi-layers and demonstrate the benefits from increased memory stability via multibit memory operation. We propose a programming methodology that allows for operating metal-oxide memristive devices as multibit memory elements with highly packed yet clearly discernible memory states. These states were found to correlate with the transport properties of the introduced barrier layers. We are demonstrating memory cells with up to 6.5 bits of information storage as well as excellent retention and power consumption performance. This paves the way for neuromorphic and non-volatile memory applications.

Overview

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Integrity signals

Registry

Crossref · 10.1038/s41598-017-17785-1

Cites

49 of 49 references verified0 citation errors · 0 not checkable

Statistics

Figures

Figure 1 Comparison between TiO2-only devices and AlxOy/TiO2 bilayer devices. (a) SEM micrograph of a memristor device; (b) Schematic representation of a single layer TiO2-based device with platinum top and bottom electrodes; (c) Schematic representation of a bilayer AlxOy/TiO2-based device with platinum top and bottom electrodes; (d) Typical bipolar switching of a device based on the stack pictured in (b) using 100 ns pulses of alternating polarity voltage ramps ranging from 1 to 2 V, with voltage steps of 200 mV; (e) Typical bipolar switching of a device based on the stack pictured in (c) using 100 ns pulses of alternating polarity voltage ramps ranging from 1 to 2 V with voltage steps of 200 mV. The coloured horizontal lines in fig. (d) and (e) denote the average low (LRS) and high resistive state (HRS).
Figure 1 Comparison between TiO2-only devices and AlxOy/TiO2 bilayer devices. (a) SEM micrograph of a memristor device; (b) Schematic representation of a single layer TiO2-based device with platinum top and bottom electrodes; (c) Schematic representation of a bilayer AlxOy/TiO2-based device with platinum top and bottom electrodes; (d) Typical bipolar switching of a device based on the stack pictured in (b) using 100 ns pulses of alternating polarity voltage ramps ranging from 1 to 2 V, with voltage steps of 200 mV; (e) Typical bipolar switching of a device based on the stack pictured in (c) using 100 ns pulses of alternating polarity voltage ramps ranging from 1 to 2 V with voltage steps of 200 mV. The coloured horizontal lines in fig. (d) and (e) denote the average low (LRS) and high resistive state (HRS).CC BY · PubMed Central
Figure 2 Multibit evaluation of devices based on different barrier layer combinations. Number of attainable resistive states (left axis) and ratio of the final state resistance over the baseline resistance (right axis) for typical bilayer devices. Confidence interval for the state assessment is 2σ following the routine described in Supplementary Figs S4 and S5. A chart containing each individual state assessed for every bilayer combination can be found in Supplementary Figs S6 and S7.
Figure 2 Multibit evaluation of devices based on different barrier layer combinations. Number of attainable resistive states (left axis) and ratio of the final state resistance over the baseline resistance (right axis) for typical bilayer devices. Confidence interval for the state assessment is 2σ following the routine described in Supplementary Figs S4 and S5. A chart containing each individual state assessed for every bilayer combination can be found in Supplementary Figs S6 and S7.CC BY · PubMed Central
Figure 3 Multibit operation of a device using the AlxOy/TiO2 RRAM stack. (a) Cumulative probability distribution function plot of a device with a record of 92 distinct resistive states. All states are read at 0.5 V, are closely packed and individually discernible; (b) switching energy required to switch a typical AlxOy/TiO2 device. Only the energy expended during programming is regarded for this graph; (c) 8 hours retention measurements for select resistive states at room temperature. (d) 8 hours retention measurements for select resistive states at 85 °C. Resistance can be retained even at elevated temperatures.
Figure 3 Multibit operation of a device using the AlxOy/TiO2 RRAM stack. (a) Cumulative probability distribution function plot of a device with a record of 92 distinct resistive states. All states are read at 0.5 V, are closely packed and individually discernible; (b) switching energy required to switch a typical AlxOy/TiO2 device. Only the energy expended during programming is regarded for this graph; (c) 8 hours retention measurements for select resistive states at room temperature. (d) 8 hours retention measurements for select resistive states at 85 °C. Resistance can be retained even at elevated temperatures.CC BY · PubMed Central
Figure 4 Programming the AlxOy/TiO2 device. Modes of selecting specific resistive states. Starting from a baseline resistance of ~27.5 kΩ a specific resistive state can be attained with different modes of programming, by modulating (i) the number of pulses, (ii) the duration of the pulses or (iii) the amplitude of the pulse. Using multiple pulses of lower amplitude and pulse width can help in pinpointing resistive states that otherwise could not have been discerned. In between the state selection the device is flushed with a series of 100 RESET pulses of 100 ns in duration.
Figure 4 Programming the AlxOy/TiO2 device. Modes of selecting specific resistive states. Starting from a baseline resistance of ~27.5 kΩ a specific resistive state can be attained with different modes of programming, by modulating (i) the number of pulses, (ii) the duration of the pulses or (iii) the amplitude of the pulse. Using multiple pulses of lower amplitude and pulse width can help in pinpointing resistive states that otherwise could not have been discerned. In between the state selection the device is flushed with a series of 100 RESET pulses of 100 ns in duration.CC BY · PubMed Central
Figure 5 Bilayer device statistics. (a) Number of resistive states ranges for different bilayer combinations. AlxOy/TiO2 devices clearly outperform all other combinations with ZnOx/TiO2 and SiOx/TiO2 exhibiting the lower amount of resistive states; (b) Attainable states distribution for 32 AlxOy/TiO2 based devices. Nearly all the devices tested exhibit at least 4 bits of information whereas 1/3 of them surpasses the 6-bit mark.
Figure 5 Bilayer device statistics. (a) Number of resistive states ranges for different bilayer combinations. AlxOy/TiO2 devices clearly outperform all other combinations with ZnOx/TiO2 and SiOx/TiO2 exhibiting the lower amount of resistive states; (b) Attainable states distribution for 32 AlxOy/TiO2 based devices. Nearly all the devices tested exhibit at least 4 bits of information whereas 1/3 of them surpasses the 6-bit mark.CC BY · PubMed Central

Verification

Claims the paper makes

The claims and statistics of this paper haven’t been checked yet.

Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.

A few free checks a day · papers already verified open instantly · results are public

Claims other papers make about this one

Each is checked against this paper’s own text: does it say what the citing paper says it does?

Self-check

Percentages, sums and reported differences re-computed from the paper’s own numbers.

The self-check needs the paper’s full text.

Citations

Cites

Show all 49 references

Research works printed but not linked: 1

  1. Verkerk, B., Winkel, P. & de Groot, D. G. On the mechanism of anodic oxidation of Tantalum. Philips Res. Repts 13, 506–508 (1958).

Cited by

See all 337

Metadata

Authors
Stathopoulos, S., Khiat, A., Trapatseli, M., Cortese, S., Serb, A., Valov, I., & Prodromakis, T.
Affiliations
  • University of Southampton (GB)
  • Forschungszentrum Jülich (DE)
Corresponding author
Prodromakis, Themis
Venue
Scientific Reports
Published
2017-12-13
Volume
7
Issue
1
Pages
17532-17532
ISSN
2045-2322 (ISSN-L)
OpenAlex
W2605663629
Cited by
312
References
49
Citations by year
2026: 7 · 2025: 25 · 2024: 31 · 2023: 41 · 2022: 39 · 2021: 46 · 2020: 57 · 2019: 39 · 2018: 26 · 2017: 1
FWCI
13.99
Type
journal article
Language
en
Open access
Licence
Locations
  • Scientific Reports (publishedVersion, cc-by)
  • PubMed Central (publishedVersion, cc-by)
  • PubMed (publishedVersion)
  • ePrints Soton (University of Southampton) (acceptedVersion)
  • DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion)
Funders
Engineering and Physical Sciences Research Council (EP/J00801X/1, EP/K017829/1, EP/J00801X/2)
Topics
  • Physical Sciences › Engineering › Electrical and Electronic Engineering › Advanced Memory and Neural Computing
  • Physical Sciences › Engineering › Electrical and Electronic Engineering › Ferroelectric and Negative Capacitance Devices
  • Physical Sciences › Engineering › Electrical and Electronic Engineering › Semiconductor materials and devices
Keywords
memristors, multi-bit memory, non-volatile memory, retention stability, barrier layer, programming methodology, neuromorphic hardware, power consumption

About these checks

Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.

Statistics and arithmetic are recomputed, not judged.

Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.

What counts as a claim ›How we measure confidence ›How we check this ›

Are you an author, or do you see a problem with this page? Request a review

How to cite

Cite CoChat for the checks on this page, and the paper for its own findings.

This page
CoChat. (2026). Citation check: Multibit memory operation of metal-oxide bi-layer memristors. https://app.cochat.ai/papers/10.1038/s41598-017-17785-1
The paper
Stathopoulos, S., Khiat, A., Trapatseli, M., Cortese, S., Serb, A., Valov, I., & Prodromakis, T. (2017). Multibit memory operation of metal-oxide bi-layer memristors. Scientific Reports. https://doi.org/10.1038/s41598-017-17785-1

Data sources

Bibliographic data: Semantic Scholar, OpenAlex, Crossref.

Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).

Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.