The DOI matches its Crossref record; 185 of the 185 references it cites were found in a registry or an index; 18 of the 167 sources its claims cite were checked for support.
Green nanoparticle synthesis at scale: a perspective on overcoming the limits of pulsed laser ablation in liquids for high-throughput production
Open accessAbstract
Nanoparticles have become increasingly important for a variety of applications, including medical diagnosis and treatment, energy harvesting and storage, catalysis, and additive manufacturing. The development of nanoparticles with different compositions, sizes, and surface properties is essential to optimize their performance for specific applications. Pulsed laser ablation in liquid is a green chemistry approach that allows for the production of ligand-free nanoparticles with diverse shapes and phases. Despite these numerous advantages, the current production rate of this method remains limited, with typical rates in the milligram per hour range. To unlock the full potential of this technique for various applications, researchers have dedicated efforts to scaling up production rates to the gram-per-hour range. Achieving this goal necessitates a thorough understanding of the factors that limit pulsed laser ablation in liquid (PLAL) productivity, including laser, target, liquid, chamber, and scanner parameters. This perspective article explores these factors and provides a roadmap for increasing PLAL productivity that can be adapted to specific applications. By carefully controlling these parameters and developing new strategies for scaling up production, researchers can unlock the full potential of pulsed laser ablation in liquids.
Overview
CoChat Summary
TL;DR
This perspective reviews why pulsed laser ablation in liquids (PLAL) typically produces nanoparticles at milligram-per-hour rates and outlines strategies to reach gram-per-hour scale. It argues that optimizing laser, target, liquid, chamber, and scanner parameters—especially picosecond lasers, fast scanning, laminar flow, and thin liquid layers—can enable industrial-scale green nanoparticle synthesis.
Key findings
- PLAL is a green, ligand-free synthesis route, but typical productivity is in the mg h⁻¹ range; the target is g h⁻¹. The paper cites a record of 8 g h⁻¹ for Pt NPs (Waag et al. 2021) and 4 g h⁻¹ for Pt using a 500 W, 10 MHz, 3 ps laser with a polygon scanner.
- Liquid flow increased femtosecond PLAL productivity from 0.79 ± 0.36 mg h⁻¹ (stationary) to 3.0 ± 0.4 mg h⁻¹; a picosecond laser with higher pulse energy and repetition rate reached 31.0 ± 0.4 mg h⁻¹. Reducing liquid layer thickness from 8 to 2.5 mm improved α-Al₂O₃ productivity from 172 to 592 mg h⁻¹. SSTF reduced nonlinear losses by 70% and increased productivity 2.4×. Polygon versus galvanometric scanning gave up to 16, 7, and 11× differences for Au, Pt, and Au₉₀Pt₁₀ targets, respectively.
- Cavitation bubbles and persistent microbubbles shield the laser beam. Higher liquid viscosity (>20 mPa s) reduced ablation yield by a factor of 3 compared with <1 mPa s; wire targets increased productivity up to 2.5× versus bulk targets. Recommended strategies include high-power picosecond lasers, fast scanning to bypass the cavitation bubble, laminar flow, low-viscosity liquid, thin liquid layers, and flow-through chambers.
- Productivity can be defined as mass, power-specific, investment-specific, volume, or mole productivity; for scale-up, the paper recommends gravimetric measurement combined with calibrated optical spectrophotometry.
Methods
- Perspective article, not a primary experimental study; it critically reviews the current status of PLAL productivity and provides a roadmap for upscaling.
- Synthesizes cited literature and prior experimental studies on laser parameters, target morphology, liquid properties, chamber design, scanner technology, and automation.
- Defines productivity metrics and measurement approaches (gravimetric, optical extinction, analytical chemistry) and compares strategies for increasing production.
Limitations
- Stated: unresolved issues remain, including the need for greater automation, remote monitoring/control, improved scanner technology, CFD simulations, temporal pulse tailoring, and further study of LIPSS effects; attosecond pulses have not yet been used for PLAL nanoparticle generation.
- Evident: as a perspective/review, it presents no new experimental data; recommendations depend on material and setup, and the paper notes that optimum liquid layer thickness depends on material and experimental setup, and that extrapolating short ablations to g h⁻¹ can be inaccurate depending on the chamber.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
12 Valid · 4 Not valid · 112 Not checked · 129 Own results and interpretations
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“For this reason, the minimum ablation duration of 5 minutes is required to obtain a reliable gram per-hour value while also accounting for the effect of nanoparticle shielding, 76 target depth variation, persistent microbubbles, 84 and scanning and repetition rate effects.54”
§ Green nanoparticle synthesis at scale: a perspective on overcoming the limits of pulsed laser ablation in liquids for highthroughput production > 3. Definition and measurement of nanoparticle productivity
What the sources say
- Partly supportedcites [76] 76. S. Dittrich, S. Barcikowski and B. Go ¨kce, Plasma and nanoparticle shielding during pulsed laser ablation in liquids cause ablation efficiency decrease, Opto-Electron. Adv., 2021, 4(1), 1-13, DOI: 10.29026/oea.2021.200072. sourceExperimental — accuracy not yet measured
Our copy of Dittrich et al. (2021) does discuss several of the effects the claim lists: nanoparticle/plasma shielding throughout, target-depth (crater) confinement of the cavitation bubble and pulse-number/repetition-rate dependence ('maximal 100 shots are applied on one spot to avoid a pulse number dependent change in the cavitation bubble', Methods and materials; 'once the depth of the drilled hole ... limits the cavitation bubble expansion', p. 200072-6), and persistent microbubbles / NPs trapped in a stationary liquid layer (p. 200072-6; 'Streaks of microbubbles along the beam path', Influence of the focal plane shift). However, no passage states or derives a minimum ablation duration of 5 minutes, or any duration requirement for obtaining a reliable gram-per-hour (gravimetric) productivity value — the paper's productivity measurements are reported without such a time criterion, and scanning effects are not addressed at all (single-spot ablation in a flow chamber at 0.5 Hz). The 5-minute threshold and its linkage to g/h reliability are therefore not supported by this source. (LLM, conf=0.62)
- Not checked — no full text of the sourcecites [84] 84. S. Reich, Patrick Scho ¨nfeld, P. Wagener, A. Letzel, S. Ibrahimkutty, B. Go ¨kce, S. Barcikowski, A. Menzel, T. D. S. Rolo and A. Plech, Pulsed laser ablation in liquids: impact of the bubble dynamics on particle formation, J. Colloid Interface Sci., 2017, 489, 106-113, DOI: 10.1016/ j.jcis.2016.08.030. source
- Partly supportedcites [54] 54. F. Waag, R. Streubel, B. Go ¨kce and S. Barcikowski, Synth- esis of gold, platinum, and gold-platinum alloy nanoparti- cle colloids with high-power megahertz-repetition-rate lasers: the importance of the beam guidance method, Appl. Nanosci., 2021, 11(4), 1303-1312, DOI: 10.1007/s13204-021- 01693-y. sourceExperimental — accuracy not yet measured
The Methods section of Waag et al. (2021) supports the core of the attribution: each LSC run lasted 5 min, and because produced nanoparticle mass increases linearly with ablation duration (shown for the same laser system in Streubel et al. 2016a), ultrafast scanning combined with liquid flow 'allows to extrapolate data from 5 min experiments to g/h statements'. The same paper also covers scanning/repetition-rate effects (Introduction and 'Effect of scan pattern length...', on pulse separation, duty cycle and delivered power) and persistent microbubbles/nanoparticles in the beam path ('Effect of beam guidance method on the productivity of platinum LSC'). Two parts are not supported: nothing in our copy addresses 'target depth variation' (the nearest passage is the ±1 mm tolerable focal-distance deviation of the flat-field image plane, credited to Streubel et al. 2016b), and the paper does not state 5 min as a required minimum duration — it reports its own 5-min run length and a justification for extrapolation, so the citing sentence's normative 'is required' overstates the source. (LLM, conf=0.75)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“The benefits from employing laser-synthesized nanomaterials for catalysis, [10][11][12]69,70 biocidal elements, 92,93 bioimaging, 94 and modification of material properties such as the absorption for additive manufacturing 95 has already been proven.”
§ Green nanoparticle synthesis at scale: a perspective on overcoming the limits of pulsed laser ablation in liquids for highthroughput production > 4. Strategies to increase nanoparticle production
What the sources say
- Not matchedcites [10][11][12]
Couldn’t be matched to a paper in Crossref, so it can’t be checked.
- Supportedcites [92] 92. P. F. S. Pereira, A. C. A. de Paula e Silva, B. N. A. da Silva Pimentel, I. M. Pinatti, A. Z. Simo ˜es, C. E. Vergani, D. F. Barreto-Vieira, M. A. N. da Silva, M. D. Miranda, M. E. S. Monteiro, A. Tucci, C. Don ˜ate-Buendı ´a, G. Mı ´nguez-Vega, J. Andre ´s and E. Longo, Inactivation of SARS-CoV-2 by a chitosan/a-Ag 2 WO 4 composite generated by femtosecond laser irradiation, Sci. Rep., 2022, 12(1), 8118, DOI: 10.1038/s41598-022-11902-5. source
This source is cited for the biocidal-elements portion of the sentence, not for catalysis, bioimaging, or additive manufacturing. The Introduction describes improved bactericidal properties after femtosecond-laser irradiation, and the Results and discussion (Biocidal analysis; page unavailable) report reduced SARS-CoV-2 viral titer for the laser-generated composite. (LLM, conf=0.92)
- Supportedcites [95] 95. T. Hupfeld, A. Wegner, M. Blanke, C. Don ˜ate-Buendı ´a, V. Sharov, S. Nieskens, M. Piechotta, M. Giese, S. Barcikowski and B. Go ¨kce, Plasmonic Seasoning: Giving Color to Desktop Laser 3D Printed Polymers by Highly Dispersed Nanoparticles, Adv. Opt. Mater., 2020, 8(15), 2000473, DOI: 10.1002/adom.202000473. source
The clause carried by citation 95 is the modification of material properties (absorption) for additive manufacturing with laser-synthesized nanoparticles, and our copy states exactly that: the Introduction reports that the aim was 'to enhance the light absorption of TPU powders ... by using a small mass fraction of silver nanoparticles' generated by LSPC (laser synthesis and processing of colloids) so that PBF-LB can be done with a 445 nm diode laser, and the Conclusion (p. ~10) confirms the nanoparticles 'act as photothermal sensitizers and enable sintering with a diode laser' at only 0.01 vol% loading, with printed parts showing measurable mechanical properties. The other listed benefits (catalysis, biocidal, bioimaging) are attributed to separate citations ([10]-[12], 69,70, 92,93, 94) and are not part of what this source is offered for; our copy only notes 'high potential' of AgNP-polymer composites in biology, catalysis and electronics (refs 43-46), which does not bear on this citation. (LLM, conf=0.88)
boostedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Not matched
Every source the paper cites for this claim was checked and supports it.
In the paper
“Wire-type targets (clamped wire and wire tip) showed a productivity increase of up to 2.5 times higher compared to the bulk target.”
§ Green nanoparticle synthesis at scale: a perspective on overcoming the limits of pulsed laser ablation in liquids for highthroughput production > 4.6. Knowing the effect of target morphology
What the sources say
- Supportedcites [100] 100. S. Kohsakowski, B. Go ¨kce, R. Tanabe, P. Wagener, A. Plech, Y. Ito and S. Barcikowski, Target geometry and rigidity determines laser-induced cavitation bubble transport and nanoparticle productivity-a high-speed videography study, Phys. Chem. Chem. Phys., 2016, 18(24), 16585-16593, DOI: 10.1039/c6cp01232a. 101 source
The Results & discussion passage states that productivity for the wire configurations increased by up to a factor of 2.5 compared with the bulk target. It also identifies the two-side clamped wire and wire tip as having productivity at the same level. (LLM, conf=0.94)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
Every source the paper cites for this claim was checked and supports it.
In the paper
“Nevertheless, the spring-like movement of the wire tip target does not increase the productivity compared to the clamped wire target, due to the limitation in the ablation set-up where the incident laser is shielded by the bubbles rising upward.”
§ Green nanoparticle synthesis at scale: a perspective on overcoming the limits of pulsed laser ablation in liquids for highthroughput production > 4.6. Knowing the effect of target morphology
What the sources say
- Supportedcites [100] 100. S. Kohsakowski, B. Go ¨kce, R. Tanabe, P. Wagener, A. Plech, Y. Ito and S. Barcikowski, Target geometry and rigidity determines laser-induced cavitation bubble transport and nanoparticle productivity-a high-speed videography study, Phys. Chem. Chem. Phys., 2016, 18(24), 16585-16593, DOI: 10.1039/c6cp01232a. 101 source
The Results & discussion passage states that wire-tip and two-side-clamped wire ablation had the same productivity. It explains that the springboard-like motion did not increase productivity because bubbles and nanoparticles moved upward toward the incident laser beam, where they could shield subsequent pulses. (LLM, conf=0.94)
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Ablation at the tip of the wire results in a 23% shorter bubble lifetime compared to the ablation in a bulk target, due to the springboard movement, which allows a larger displacement of the bubble, as shown in Fig. 11b.”
§ Green nanoparticle synthesis at scale: a perspective on overcoming the limits of pulsed laser ablation in liquids for highthroughput production > 4.6. Knowing the effect of target morphology
What the sources say
- Partly supportedcites Kohsakowski et al. (2016) sourceExperimental — accuracy not yet measured
The Results & discussion section reports that the bubble lifetime at the wire tip is 23% shorter than at the bulk target, and separately describes springboard-driven bubble displacement. It attributes the bulk-target bubble’s longer lifetime to its greater expansion, not to the absence of springboard movement; the claimed causal link is therefore unsupported. (LLM, conf=0.87)
- Partly supportedcites [100] 100. S. Kohsakowski, B. Go ¨kce, R. Tanabe, P. Wagener, A. Plech, Y. Ito and S. Barcikowski, Target geometry and rigidity determines laser-induced cavitation bubble transport and nanoparticle productivity-a high-speed videography study, Phys. Chem. Chem. Phys., 2016, 18(24), 16585-16593, DOI: 10.1039/c6cp01232a. 101 sourceExperimental — accuracy not yet measured
The Results & discussion section reports that the bubble lifetime at the wire tip is 23% shorter than at the bulk target and that springboard-like wire movement allows greater bubble displacement. It does not attribute the shorter lifetime to that movement; instead, it links the bulk-target bubble’s longer lifetime to its greater expansion. Page numbers are unavailable in our copy. (LLM, conf=0.86)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
122 more claims · 3 with their cited sources checked
Create a free account to see all 257 claims and to verify the 23 references still open.
- Probably not a substantial claim. 68
- It may state two separate claims as one. 83
- The quote only partly states this claim. 1
Citations
Cites
Synthesis and surface engineering of iron oxide nanoparticles for biomedical applications
Gupta, A. K., & Gupta, M. (2005) · Biomaterials · doi:10.1016/j.biomaterials.2004.10.012 · Cited by 6,771
Applications of magnetic nanoparticles in biomedicine
Pankhurst, Q. A., Connolly, J., Jones, S. K., & Dobson, J. (2003) · Journal of Physics D: Applied Physics · doi:10.1088/0022-3727/36/13/201 · Cited by 5,881
Co3O4 nanocrystals on graphene as a synergistic catalyst for oxygen reduction reaction
Liang, Y., Li, Y., Wang, H., Zhou, J., Wang, J., Regier, T., & Dai, H. (2011) · Nature Materials · doi:10.1038/nmat3087 · Cited by 5,494
Green Chemistry: Principles and Practice
Anastas, P., & Eghbali, N. (2010) · Chem. Soc. Rev. · doi:10.1039/b918763b · Cited by 5,256
MoS 2 Nanoparticles Grown on Graphene: An Advanced Catalyst for the Hydrogen Evolution Reaction
Li, Y., Wang, H., Xie, L., Liang, Y., Hong, G., & Dai, H. (2011) · Journal of the American Chemical Society · doi:10.1021/ja201269b · Cited by 5,001
Review on Zinc Oxide Nanoparticles: Antibacterial Activity and Toxicity Mechanism
Sirelkhatim, A., Mahmud, S., Seeni, A., Kaus, N. H. M., Ann, L. C., Bakhori, S. K. M., Hasan, H., & Mohamad, D. (2015) · Nano-Micro Letters · doi:10.1007/s40820-015-0040-x · Cited by 4,586
Ultra-large-scale syntheses of monodisperse nanocrystals
Park, J., An, K., Hwang, Y., Park, J.-G., Noh, H.-J., Kim, J.-Y., Park, J.-H., Hwang, N.-M., & Hyeon, T. (2004) · Nature Materials · doi:10.1038/nmat1251 · Cited by 4,076
Determination of Size and Concentration of Gold Nanoparticles from UV−Vis Spectra
Haiss, W., Thanh, N. T. K., Aveyard, J., & Fernig, D. G. (2007) · Analytical Chemistry · doi:10.1021/ac0702084 · Cited by 3,677
Nanomaterials: a review of synthesis methods, properties, recent progress, and challenges
Baig, N., Kammakakam, I., & Falath, W. (2021) · Materials Advances · doi:10.1039/d0ma00807a · Cited by 3,262
Femtosecond, picosecond and nanosecond laser ablation of solids
Chichkov, B. N., Momma, C., Nolte, S., Alvensleben, F., & Tünnermann, A. (1996) · Applied Physics A Materials Science & Processing · doi:10.1007/bf01567637 · Cited by 3,066
Research works printed but not linked: 4
- Fojtik, 1993, Berichte der Bunsen-Gesellschaft, 97, 252
- Amendola, 2020, Chem. – Eur. J., 26, 9206, 10.1002/chem.202000686 · DOI · Paper page
- Tunnermann, 2010, Pulse, 49, 34
- D.-I. J.Berkmanns and D.-I. M.Faerber , Laser basics - LASERLINE Technical. , 2008
Cited by
Rethinking Nanoparticle Synthesis: A Sustainable Approach vs. Traditional Methods
Jain, K., Takuli, A., Gupta, T. K., & Gupta, D. (2024) · Chemistry - An Asian Journal · doi:10.1002/asia.202400701 · Cited by 182
Manshina, A., Tumkin, I. I., Khairullina, E. M., Mizoshiri, M., Ostendorf, A., Kulinich, S. A., Makarov, S., Kuchmizhak, A. A., & Gurevich, E. L. (2024) · Advanced Functional Materials · doi:10.1002/adfm.202405457 · Cited by 125
Martínez-Chávez, L. A., Hernández-Ramírez, M. Y., Feregrino‐Pérez, A. A., & Esquivel, K. (2024) · Agronomy · doi:10.3390/agronomy14122822 · Cited by 60
Rajkumar, M., Presley, S. I. D., Thiyagarajulu, N., Girigoswami, K., Janani, G., Kamaraj, C., Madheswaran, B., Prajapati, B. G., Ali, N., & Khan, M. R. (2025) · Scientific Reports · doi:10.1038/s41598-024-84098-5 · Cited by 47
Ahmed, M. R., Manik, K. H., Islam, M. S., Rhine, A., Mim, J. J., & Hossain, N. (2026) · Next Materials · doi:10.1016/j.nxmate.2026.101929 · Cited by 62
Metadata
- Authors
- Khairani, I. Y., Mínguez-Vega, G., Doñate-Buendía, C., & Gökce, B.
- Affiliations
- University of Wuppertal (DE)
- GROC-UJI, Institut de Noves Tecnologies de la Imatge (INIT), Universitat Jaume I, 12071, Castellón, Spain
- Chair of Materials Science and Additive Manufacturing, School of Mechanical Engineering and Safety Engineering, University of Wuppertal, 42119 Wuppertal, Germany
- Corresponding author
- Gökce, Bilal
- Venue
- Physical Chemistry Chemical Physics
- Publisher
- Royal Society of Chemistry (RSC)
- Published
- 2023
- Volume
- 25
- Issue
- 29
- Pages
- 19380-19408
- ISSN
- 1463-9076 (ISSN-L)
- 1463-9084
- OpenAlex
- W4383426422
- Cited by
- 130
- References
- 181
- Citations by year
- 2026: 44 · 2025: 53 · 2024: 28 · 2023: 5
- FWCI
- 2.91
- Type
- journal article
- Language
- en
- Open access
- hybrid
- doi.org
- Licence
- Locations
- Physical Chemistry Chemical Physics (publishedVersion, cc-by-nc)
- PubMed (publishedVersion)
- Repositori UJI (Universitat Jaume I) (submittedVersion, cc-by-nc)
- Funders
- Deutsche Forschungsgemeinschaft (GO 2566/10-1, GO 2566/14-1)
- European Commission (952068)
- Topics
- Physical Sciences › Materials Science › Materials Chemistry › Laser-Ablation Synthesis of Nanoparticles
- Physical Sciences › Physics and Astronomy › Acoustics and Ultrasonics › Ultrasound and Cavitation Phenomena
- Physical Sciences › Materials Science › Electronic, Optical and Magnetic Materials › Gold and Silver Nanoparticles Synthesis and Applications
- Keywords
- pulsed laser ablation in liquid, green synthesis of nanoparticles, ligand-free nanoparticles, laser parameters, target materials, nanoparticle size and shape control
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (qwen3.8-omni-flash and gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Green nanoparticle synthesis at scale: a perspective on overcoming the limits of pulsed laser ablation in liquids for high-throughput production. https://app.cochat.ai/papers/10.1039/d3cp01214j
- The paper
- Khairani, I. Y., Mínguez-Vega, G., Doñate-Buendía, C., & Gökce, B. (2023). Green nanoparticle synthesis at scale: a perspective on overcoming the limits of pulsed laser ablation in liquids for high-throughput production. Physical Chemistry Chemical Physics. https://doi.org/10.1039/d3cp01214j
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.