The DOI matches its Crossref record; 123 of the 123 references it cites were found in a registry or an index; 54 of the 167 sources its claims cite were checked for support.
Nano-hydroxyapatite/collagen composite as scaffold material for bone regeneration.
Open accessAbstract
Human bone is mainly comprised of a hydroxyapatite (HA)/collagen complex.
Overview
CoChat Summary
TL;DR
This review summarizes nano-hydroxyapatite/collagen composite scaffolds for bone regeneration, emphasizing collagen’s bioactivity and nano-HA’s contributions to mechanical strength, osteoconductivity, and mineralization. It surveys fabrication methods—electrospinning, additive manufacturing, freeze drying, TIPS, and coating—and reports selected in vitro and in vivo outcomes while noting collagen scaffold limitations.
Key findings
- Nano-HA can improve mechanical properties without destroying porosity: Cunniffe et al. reported collagen Young’s modulus of 0.3 kPa, a 12-fold increase for I-high nano-HA/collagen, and porosity of 99.5% for collagen, 99.4% for S-100, and 98.9% for I-high. However, high nano-HA concentration can reduce porosity: Liu reported 54% porosity for HA-rich scaffold versus 78% for HA-deplete scaffold. The optimum pore size was reported as 300–400 µm for alkaline phosphatase activity, osteocalcin, and delicate blood vessel formation.
- Nano-HA/collagen supports bone regeneration and vascularization: Liao et al.’s nano-HA/collagen/PLA scaffold had interconnected pores of 100–300 µm and showed complete bone regeneration in a rabbit 15 mm segmental defect after 12 weeks. Chen et al. observed blood supply around chitosan/nano-HA/collagen at 14 and 28 days, though vascularization was not observed in the scaffold after 28 days.
- Drug-loaded and antibacterial nano-HA/collagen scaffolds were reported: Rong et al.’s adriamycin-PLGA/nano-HA/collagen scaffold released 65% of drug over 28 days; in nude mice, tumor weights for groups A–D were 3.36 ± 0.29 g, 1.54 ± 0.17 g, 1.82 ± 0.14 g, and 1.11 ± 0.09 g, and tumor volumes were 9.72 ± 0.72 cm³, 4.24 ± 0.31 cm³, 5.57 ± 0.37 cm³, and 2.68 ± 0.22 cm³. Lian et al.’s vancomycin-loaded scaffold showed an inhibition zone of 21.7 ± 0.6 mm after 72 h and 1.5 ± 1.0 mm after four weeks.
- Fabrication route affects scaffold architecture and performance: freeze-dried nano-HA/collagen/PLLA showed 19.6% weight loss after 4 weeks in vitro; TIPS-made nHAC/PLLA/CMs with 30% or less chitosan microspheres did not significantly affect porosity; 3D-printed nano-HA/collagen Group II (600 µm rods) showed better degradation and bone regeneration but moderate mechanical behavior.
Methods
- Design: narrative review; the paper states no new data were created or analysed. It synthesizes literature on natural biopolymers, collagen, nano-HA/collagen scaffolds, fabrication techniques, and reported outcomes.
- Data/sample: cited studies include in vitro cell studies (e.g., MC3T3-E1, rabbit marrow mesenchymal stem cells, human adipose-derived mesenchymal stem cells) and in vivo animal models (rabbits, nude mice); tables summarize scaffold composition, pore size, porosity, and preparation method.
- Main analysis: qualitative synthesis of reported scaffold properties and biological outcomes; no meta-analysis or primary statistical analysis is stated.
Limitations
- The paper states collagen-based scaffolds have drawbacks: mammalian collagen may transmit disease; collagen scaffolds lack sufficient strength; chemical cross-linking can compromise biological functionalities; UV cross-linking can denature collagen; degradation is difficult to monitor and predict in vivo due to collagenase; extensive optimization is required.
- The paper states long-term efficacy of nano-HA/collagen coatings is uncertain because collagen and HA may detach as the scaffold degrades, and reports on nano-HA/collagen prepared by TIPS are scarce.
- Evident from the text: the review mixes many scaffold compositions, fabrication methods, and animal/cell models, so reported pore sizes, porosities, and biological outcomes are not directly comparable.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
48 Valid · 6 Not valid · 109 Not checked · 34 Own results and interpretations
At least one cited source doesn’t support this claim or points to a different paper, and none confirmed it — see the verdicts below.
In the paper
“This scaffold was capable of delivering strontium ions”
§ A bone-like nano-hydroxyapatite/collagen loaded injectable scaffold > 5.2. Additive manufacturing
What the sources say
- Disputedcites [80] Melo, 2021, 3D printing in alginic acid bath of in-situ crosslinked collagen composite scaffolds, Materials sourceExperimental — accuracy not yet measured
The Materials section (2.1) identifies two distinct formulations: collagen with strontium-containing mesoporous bioactive glass (Coll/MBG_Sr4%) and collagen with nano-hydroxyapatite (Coll/nanoHA). The Results (3.3) confirm strontium-ion release from the MBG-containing formulation, not from the nano-HA/collagen scaffold named in the claim. (LLM, conf=0.88)
Checked by a reasoning model — may be wrong.
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Disputed
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Lei et al [59] reported that the release of Ca 2+ from nano-HA did not require any complicated process as the large surface area of nano-HA readily release Ca 2+ ions.”
§ A bone-like nano-hydroxyapatite/collagen loaded injectable scaffold > 4.1. Influence of nano HA on bone mineralization
What the sources say
- Partly supportedcites [59] Lei, 2019, Comparative evaluation of the physicochemical properties of nano-hydroxyapatite/collagen and natural bone ceramic/collagen scaffolds and their osteogenesis-promoting effect on MC3T3-E1 cells, Regen. Biomater. sourceExperimental — accuracy not yet measured
The Discussion says Ca2+ may be released more easily from nHA than from NBC and links NBC’s lower release rate to its lower specific surface area. It does not say that release requires no complicated process, and it presents the proposed explanation as needing further experimental validation. No page number is available in our copy. (LLM, conf=0.85)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“However, the immunological response, non-degradability, and toxicity of metalbased, ceramic-based, and synthetic polymer-based scaffolds hinder their commercial viability [7].”
§ A bone-like nano-hydroxyapatite/collagen loaded injectable scaffold > 1. Introduction
What the sources say
- Could not verifycites [7] Gilpin, 2017, Decellularization strategies for regenerative medicine: from processing techniques to applications, Biomed. Res. Int. sourceExperimental — accuracy not yet measured
The Introduction describes synthetic scaffolds as tunable but does not address their toxicity, degradability, or commercial viability. Section 3.1 discusses immunogenicity as a barrier for decellularized ECM scaffolds, not metal-, ceramic-, or synthetic polymer-based scaffolds. Searches for those materials and the claimed limitations found no passage addressing the attributed point. (LLM, conf=0.75)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Could not verify
Every source the paper cites for this claim was checked and supports it.
In the paper
“Reports validate that the nano sized particles are capable of serving as pro-adhesive agents [55].”
§ A bone-like nano-hydroxyapatite/collagen loaded injectable scaffold > 4.1. Influence of nano HA on bone mineralization
What the sources say
- Supportedcites [55] Zheng, 2014, Evaluation of novel in situ synthesized nano-hydroxyapatite/collagen/alginate hydrogels for osteochondral tissue engineering, Biomed. Mater. source
The Introduction states that nanoparticles could serve as “pro-adhesive” agents and enhance cell adhesion. This directly supports the attributed claim. (LLM, conf=0.94)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
Every source the paper cites for this claim was checked and supports it.
In the paper
“An inhibition zone of 1.5 ± 1.0 mm was observed even after four weeks of incubation.”
§ A bone-like nano-hydroxyapatite/collagen loaded injectable scaffold > 4.5. Nano-HA/collagen scaffold for bone disease treatment
What the sources say
- Supportedcites [71] Lian, 2013, Antibacterial and biocompatible properties of vancomycin-loaded nano-hydroxyapatite/collagen/poly (lactic acid) bone substitute, Prog. Nat. Sci. source
The Antibiotic activity section (3.3) reports a 1.5 ± 1.0 mm inhibition zone after the scaffold had been immersed in PBS for four weeks. The four-week period refers to PBS immersion, not incubation on an agar plate; the agar-plate assay ran for up to 18 days. (LLM, conf=0.90)
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
117 more claims · 31 with their cited sources checked
Create a free account to see all 197 claims and every source verdict.
- It may state two separate claims as one. 54
- Probably not a substantial claim. 25
- The quote only partly states this claim. 2
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ A bone-like nano-hydroxyapatite/collagen loaded injectable scaffold > 4.3. Influence of nano-HA on porosity
“Further, from the table, it can be inferred that all the research work focused on developing scaffolds with pore sizes of more than 100 µm with high interconnected porosity since they create an environment that facilitates efficient bone regeneration.”
§ A bone-like nano-hydroxyapatite/collagen loaded injectable scaffold > 5.4. Thermally induced phase separation (TIPS) technique
“17.Collagen/ nano-HA scaffold -Freeze drying 50-80 µm 45%”
Citations
Cites
Collagens—structure, function, and biosynthesis
Gelse, K. (2003) · Advanced Drug Delivery Reviews · doi:10.1016/j.addr.2003.08.002 · Cited by 2,654
Biomedical applications of collagen
Lee, C. H., Singla, A., & Lee, Y. (2001) · International Journal of Pharmaceutics · doi:10.1016/s0378-5173(01)00691-3 · Cited by 1,945
Wei, G., & Ma, P. X. (2004) · Biomaterials · doi:10.1016/j.biomaterials.2003.12.005 · Cited by 1,271
Cellulose-based hydrogels: Present status and application prospects
Chang, C., & Zhang, L. (2011) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2010.12.023 · Cited by 1,081
Fibrin: A versatile scaffold for tissue engineering applications
Ahmed, T. A. E., Dare, E. V., & Hincke, M. (2008) · Tissue Engineering Part B: Reviews · doi:10.1089/ten.teb.2007.0435 · Cited by 994
3D printing of composite calcium phosphate and collagen scaffolds for bone regeneration
Inzana, J. A., Olvera, D., Fuller, S. M., Kelly, J. P., Graeve, O. A., Schwarz, E. M., Kates, S. L., & Awad, H. A. (2014) · Biomaterials · doi:10.1016/j.biomaterials.2014.01.064 · Cited by 840
Decellularization Strategies for Regenerative Medicine: From Processing Techniques to Applications
Gilpin, A., & Yang, Y. (2017) · BioMed Research International · doi:10.1155/2017/9831534 · Cited by 742
Keselowsky, B. G., Collard, D. M., & Garcı́a, A. J. (2004) · Biomaterials · doi:10.1016/j.biomaterials.2004.01.062 · Cited by 627
Biofabrication of bone tissue: approaches, challenges and translation for bone regeneration
Tang, D., Tare, R. S., Yang, L.-Y., Williams, D. F., Ou, K.-L., & Oreffo, R. O. C. (2016) · Biomaterials · doi:10.1016/j.biomaterials.2016.01.024 · Cited by 613 · cited 1×
“Due to their large surface area and porous structure, they create an environment that encourages cell attachment and rapid diffusion of nutrients which are important prerequisites for cell survival and growth [18].”
Chitosan Based Polyelectrolyte Complexes as Potential Carrier Materials in Drug Delivery Systems
Hamman, J. H. (2010) · Marine Drugs · doi:10.3390/md8041305 · Cited by 569
Cited by
Application of gelatin-based composites in bone tissue engineering
Wu, E., Huang, L., Shen, Y., Wei, Z., Li, Y., Wang, J., & Chen, Z. (2024) · Heliyon · doi:10.1016/j.heliyon.2024.e36258 · Cited by 71
“Optimal bone scaffold materials should have structural properties similar to natural bone tissue, including excellent biocompatibility, mechanical properties, appropriate porosity and biodegradability [14,15].”
BackgroundSalim, N. V., Madhan, B., Glattauer, V., & Ramshaw, J. A. M. (2024) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2024.134374 · Cited by 67
Wassif, R. K., Elkheshen, S. A., Shamma, R. N., Amer, M., Elhelw, R. A., & El-Kayal, M. (2023) · Drug Delivery and Translational Research · doi:10.1007/s13346-023-01384-x · Cited by 46
“…nHA in bone scaffolds with or without natu-ral polymers is very well known to be beneficial for the process of bone regeneration due to the similarity of nHA to the natural extracellular matrix (ECM) of bones, together with its ability to increase the mechanical strength of the formed gel [12–14].”
BackgroundDorozhkin, S. V. (2024) · Journal of Composites Science · doi:10.3390/jcs8060218 · Cited by 50
Bioactive strong biodegradable bone cement for rapid osteointegration and osteogenesis
Zhao, X., Gao, J., Han, H., et al. (2023) · Chemical Engineering Journal · doi:10.1016/j.cej.2023.145609 · Cited by 38
Metadata
- Authors
- Kavitha Sri, A., Arthi, C., Neya, N. R., & Hikku, G. S.
- Affiliations
- Chettinad Academy of Research and Education (IN)
- Corresponding author
- Hikku, G S
- ORCID
- Hikku, G S
- Venue
- Biomedical Materials
- Publisher
- IOP Publishing
- Published
- 2023-04-14
- Volume
- 18
- Issue
- 3
- Pages
- 032002
- ISSN
- 1748-6041 (ISSN-L)
- 1748-605X
- OpenAlex
- W4362458342
- Cited by
- 57
- References
- 122
- Citations by year
- 2026: 16 · 2025: 17 · 2024: 19 · 2023: 5
- FWCI
- 1.28
- Type
- journal article
- Language
- en
- Open access
- hybrid
- doi.org
- Licence
- cc-by
- publishingsupport.iopscience.iop.org/iop-standard/v1 (vor)
- iopscience.iop.org/info/page/text-and-data-mining (tdm)
- Locations
- Biomedical Materials (publishedVersion, cc-by)
- PubMed (publishedVersion)
- Funders
- Chettinad Academy of Research and Education
- Topics
- Physical Sciences › Engineering › Biomedical Engineering › Bone Tissue Engineering Materials
- Physical Sciences › Materials Science › Biomaterials › Collagen: Extraction and Characterization
- Physical Sciences › Materials Science › Biomaterials › Electrospun Nanofibers in Biomedical Applications
- Keywords
- hydroxyapatite nanoparticles, collagen, hydroxyapatite/collagen composite, bone regeneration, bone tissue engineering, scaffolds, scaffold fabrication, cell adhesion, bone defects
- MeSH terms
- Bone and Bones, Bone Regeneration, Collagen, Humans, Durapatite, Tissue Engineering, Tissue Scaffolds
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-08, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-08 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Nano-hydroxyapatite/collagen composite as scaffold material for bone regeneration. https://app.cochat.ai/papers/10.1088/1748-605x/acc99e
- The paper
- Kavitha Sri, A., Arthi, C., Neya, N. R., & Hikku, G. S. (2023). Nano-hydroxyapatite/collagen composite as scaffold material for bone regeneration. Biomedical Materials. https://doi.org/10.1088/1748-605x/acc99e
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.