Comparative study of hot corrosion behavior of bare and plasma sprayed Al 2 O 3 -40%TiO 2 coated T-91, A-1 boiler steel and Superfer800H superalloy in Na 2 SO 4 -60%V 2 O 5 salt environment
The DOI matches its Crossref record; 44 of the 44 references it cites were found in a registry or an index.
Abstract
In the present study, the bi-layer NiCrAlY/Al 2 O 3 -40%TiO 2 coating was deposited on the three substrates (A-1, T-91, & Superfer800H) by utilizing a plasma spray technique. NiCrAlY was used as a bond coat for ensuring a proper mechanical anchorage of the topcoat (Al 2 O 3 -40%TiO 2 ) on to it. The hot corrosion behavior of the coated as well as uncoated substrate was evaluated in an aggressive environment of Na 2 SO 4 -60%V 2 O 5 molten salt at 900 °C for 50 cycles (1 h of heating followed by 20 min of cooling at ambient temperature). Thermogravimetric analysis was done to establish the corrosion kinetics of the coated as well as the uncoated substrate. The surface morphology of the as-sprayed and corroded products was analyzed by using a scanning electron microscope (SEM) system, and various phases formed were analyzed by utilizing an x-ray Diffraction (XRD) apparatus. Iron oxide (Fe 2 O 3 ) is the principal phase formed in the tested uncoated substrate which is non-protective in nature; whereas the presence of Al, and Ti oxides along with some minor oxides of Ni, and Cr were observed in the oxide scale of the tested coated substrate, which are protective and remain stable even at harsh environment condition. The weight gain shown by the coated substrate is less as compared to the uncoated substrate, which indicates the usefulness of the coating.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Citations
Cites
1 retracted
Singh, G., Kumar, S., & Kumar, R. (2020) · Materials Research Express · doi:10.1088/2053-1591/ab6e7e · Cited by 21
RetractedFauchais, P. L., Heberlein, J. V. R., & Boulos, M. I. (2014) · Springer eBooks · doi:10.1007/978-0-387-68991-3 · Cited by 857
High temperature corrosion in energy systems
Rapp, R. A., Devan, J. H., Douglass, D. L., Nordine, P. C., Pettit, F. S., & Whittle, D. P. (1981) · Materials Science and Engineering · doi:10.1016/0025-5416(81)90082-3 · Cited by 366
Introduction to High Temperature Oxidation and Corrosion
Khanna, A. S. (2002) · Cited by 364
Thermal Spray Fundamentals. From powder to part
Fauchais, P. L., Heberlein, J. V. R., & Boulos, M. (2013) · INRIA a CCSD electronic archive server · Cited by 323
Hot corrosion of materials: Fundamental studies
Rapp, R. A., & Zhang, Y.-S. (1994) · JOM · doi:10.1007/bf03222665 · Cited by 247
Hot Corrosion of Metals and Alloys
Pettit, F. (2011) · Oxidation of Metals · doi:10.1007/s11085-011-9254-6 · Cited by 241
Combating hot corrosion of boiler tubes – A study
Kumar, S., Kumar, M., & Handa, A. (2018) · Engineering Failure Analysis · doi:10.1016/j.engfailanal.2018.08.004 · Cited by 207
Chemistry and electrochemistry of hot corrosion of metals
Rapp, R. A. (1987) · Materials Science and Engineering · doi:10.1016/0025-5416(87)90394-6 · Cited by 155
Kamal, S., Jayaganthan, R., Prakash, S., & Kumar, S. (2007) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2007.09.019 · Cited by 154
Review of inorganic coatings and coating processes for reducing wear and corrosion
Sidky, P. S., & Hocking, M. G. (1999) · British Corrosion Journal · doi:10.1179/000705999101500815 · Cited by 141
Accelerated hot corrosion studies of cold spray Ni–50Cr coating on boiler steels
Bala, N., Singh, H., & Prakash, S. (2010) · Materials & Design · doi:10.1016/j.matdes.2009.06.033 · Cited by 128
Kamal, S., Jayaganthan, R., & Prakash, S. (2008) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2008.09.031 · Cited by 125
Kumar, S., Kumar, M., & Handa, A. (2019) · Engineering Failure Analysis · doi:10.1016/j.engfailanal.2019.104173 · Cited by 119
Bai, C.-Y., Luo, Y.-J., & Koo, C.-H. (2003) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2003.10.011 · Cited by 102
Thermochemistry and Solubilities of Oxides in Sodium Sulfate-Vanadate Solutions
Hwang, Y.-S., & Rapp, R. A. (1989) · Corrosion · doi:10.5006/1.3585003 · Cited by 82
An Assessment of Thermal Spray Coating Technologies for High Temperature Corrosion Protection
Heath, G. R., Heimgartner, P., Irons, G., Miller, R. D., & Gustafsson, S. (1997) · Materials science forum · doi:10.4028/www.scientific.net/msf.251-254.809 · Cited by 81
Effect of TiO2 content on properties of Al2O3 thermal barrier coatings by plasma spraying
Sheng-kai, J. I. A., Zou, Y., Xu, J., Jing, W. A. N. G., & Yu, L. (2015) · Transactions of Nonferrous Metals Society of China · doi:10.1016/s1003-6326(15)63593-2 · Cited by 80
Studies on erosion behaviour of plasma sprayed coatings on a Ni-based superalloy
Mishra, S. B., Prakash, S., & Chandra, K. S. (2005) · Wear · doi:10.1016/j.wear.2005.02.098 · Cited by 79
Corrosion Resistance of APS- and HVOF-Sprayed Coatings in the Al2O3-TiO2 System
Toma, F.-L., Stahr, C. C., Berger, L. ‐., Saaro, S., Herrmann, M., Deska, D., & Michael, G. (2009) · Journal of Thermal Spray Technology · doi:10.1007/s11666-009-9422-2 · Cited by 78
Chemical Reactions Involved in the Initiation of Hot Corrosion of IN‐738
Fryburg, G. C., Kohl, F. J., & Stearns, C. A. (1984) · Journal of The Electrochemical Society · doi:10.1149/1.2115455 · Cited by 78
Higuera Hidalgo, V., Belzunce Varela, F. J., & Fernández Rico, E. (1997) · Tribology International · doi:10.1016/s0301-679x(97)00029-7 · Cited by 76
Analysis of failures in boiler tubes due to fireside corrosion in a waste heat recovery boiler
Srikanth, S., Ravikumar, B., Das, S. K., Gopalakrishna, K., Nandakumar, K., & Vijayan, P. (2002) · Engineering Failure Analysis · doi:10.1016/s1350-6307(02)00030-4 · Cited by 74
Hot corrosion performance of a NiCr coated Ni-based alloy
SIDHU, T., PRAKASH, S., & AGRAWAL, R. (2006) · Scripta Materialia · doi:10.1016/j.scriptamat.2006.03.054 · Cited by 70
Reactions Between Sodium Sulphate and Vanadium Pentoxide
Kolta, G. A., Hewaidy, I. F., & Felix, N. S. (1972) · Thermochimica Acta · doi:10.1016/s0040-6031(72)80029-7 · Cited by 67
Vasudev, H., Thakur, L., SINGH, H., & Bansal, A. (2018) · Kovove Materialy-Metallic Materials · doi:10.4149/km_2018_1_55 · Cited by 64
Self-citationSidhu, H. S., Sidhu, B. S., & Prakash, S. (2005) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2005.07.008 · Cited by 63
Evaluation of hot corrosion behaviour of HVOF sprayed NiCrAl coating on superalloys at 900°C
Mahesh, R. A., Jayaganthan, R., & Prakash, S. (2008) · Materials Chemistry and Physics · doi:10.1016/j.matchemphys.2008.05.006 · Cited by 59
Corrosion-Erosion Behavior of Materials in a Coal-Gasification Environment
Natesan, K. (1976) · CORROSION · doi:10.5006/0010-9312-32.9.364 · Cited by 56
Kaur, M., Singh, H., & Prakash, S. (2008) · Anti-Corrosion Methods and Materials · doi:10.1108/00035590810859467 · Cited by 50
Microstructure formation in high velocity oxy-fuel thermally sprayed Ni–Cr–Mo–B alloys
Dent, A. H., Horlock, A. J., McCartney, D. G., & Harris, S. J. (2000) · Materials Science and Engineering A · doi:10.1016/s0921-5093(00)00747-4 · Cited by 48
Chatha, S. S., Sidhu, H. S., & Sidhu, B. S. (2013) · Journal of Thermal Spray Technology · doi:10.1007/s11666-013-9899-6 · Cited by 41
Erosion Corrosion Study of HVOF Sprayed Thermal Sprayed Coatings on Boiler Tubes:A Review
Kumar, R., Kumar, R., & Kumar, S. (2018) · International Journal of Science and Management Studies (IJSMS) · doi:10.51386/25815946/ijsms-v1i3p101 · Cited by 41
Rani, A., Bala, N., & Gupta, C. M. (2017) · Oxidation of Metals · doi:10.1007/s11085-017-9759-8 · Cited by 28
High temperature oxidation behaviour and characterization of NiCrAlY-B4C coatings deposited by HVOF
Singh, G., Bala, N., & Chawla, V. (2019) · Materials Research Express · doi:10.1088/2053-1591/ab1f96 · Cited by 19
Self-citationLee, J. (2003) · Journal of Materials Science · doi:10.1023/a:1023215424025 · Cited by 18
Mishra, N. K., & Mishra, S. B. (2015) · Bulletin of Materials Science · doi:10.1007/s12034-015-0986-9 · Cited by 16
The information technology knowledge infrastructure and research in South Asia
Singh, V. K., Singhal, K., Banshal, S., & Uddin, A. (2014) · Journal of Scientometric Research · doi:10.4103/2320-0057.153578 · Cited by 15
Performance of Al2O3-3%TiO2 Detonation gun coated ferritic steels in coal fired boiler
Sapra, P. K., Singh, S. P., Prakash, S., & Arivazhagan, N. (2009) · International Journal of Surface Science and Engineering · doi:10.1504/ijsurfse.2009.024368 · Cited by 13
Chawla, V., Puri, D., Prakasha, S., Chawla, A., & Sidhu, B. S. (2009) · Journal of Minerals and Materials Characterization and Engineering · doi:10.4236/jmmce.2009.89062 · Cited by 9
Self-citationDevelopment of Hot Corrosion on Coated Single Crystal Superalloys
Simms, N. J., Encinas‐Oropesa, A., & Nicholls, J. R. (2004) · Materials science forum · doi:10.4028/www.scientific.net/msf.461-464.941 · Cited by 9
Properties of non-aqueous solutions of Ni(CF3SO3)2
Takei, T. (1987) · Surface and Coatings Technology · doi:10.1016/0257-8972(87)90069-7 · Cited by 7
Surface and coating technologies
Bräuer, G., & Kondruweit, S. (2009) · Springer eBooks · doi:10.1007/978-3-540-88546-7_9 · Cited by 5
Effect of TiO2 on Plasma Sprayed Al2O3 Based Composite Coatings at 900℃ in Molten Salt Environment
Singh, G., Goyal, K., & Goyal, R. (2019) · Universal Journal of Mechanical Engineering · doi:10.13189/ujme.2019.070501 · Cited by 4
Research works printed but not linked: 11
- Khanna, 1998, Trans. Indian Inst. Met., 51, 279
- Liu, 2005, Journal of the European Society, 25, 133
- Mangla, 2017, International. Journal. of Engineering. Science. and Research. Technology, 6, 674
- Chatha, 2013, Thermal Spray Technology, 22, 838, 10.1007/s11666-013-9899-6 · DOI · Paper page
- Priyantha, 2003, Surface and Coating Technology, 31, 163
- Chawla, 2008, J. Aust. Ceram. Soc., 44, 56
- Chawla, 2010, Journal of Minerals and Materials Characterization and Engineering, 593–606, 2010
- Mehta, 2018, Journal of Material Science and Mechanical Engineering, 5, 181
- Simms, 2004, Material Science Forum, 461–464, 941, 10.4028/www.scientific.net/msf.461-464.941 · DOI
- Chawla, 2011, J. Australas. Ceram. Soc., 47, 48
- Sheng-Kai, 2015, Transactions of Nonferrous Metals Society of China, 25, 175, 10.1016/s1003-6326(15)63593-2 · DOI
Cited by
Kumar, S. S., Prasad, C. D., & Hanumanthappa, H. (2024) · Journal of Bio- and Tribo-Corrosion · doi:10.1007/s40735-024-00822-8 · Cited by 31
“In contrast, the oxidation performance of the HVOF approaches is valued for a range of coated and uncoated substrates at temperatures between 550 and 800 °C, as shown in Table 4 [56, 57].”
High Temperature Corrosion Resistant and Anti-slagging Coatings for Boilers: A Review
Khantisopon, K., Singh, S., Jitputti, J., Berndt, C. C., & Ang, A. S. M. (2024) · High Temperature Corrosion of Materials · doi:10.1007/s11085-024-10251-0 · Cited by 30
Metadata
- Authors
- Ansari, M. S., Bansal, A., Chawla, V., & Aggarwal, V.
- Affiliations
- Punjab Technical University (IN)
- Corresponding author
- Ansari, Mohd Shadab
- Venue
- Surface Topography: Metrology and Properties
- Publisher
- IOP Publishing
- Published
- 2021-05-28
- Volume
- 9
- Issue
- 2
- Pages
- 025029
- ISSN
- 2051-672X (ISSN-L)
- OpenAlex
- W3162210757
- Cited by
- 2
- References
- 43
- Citations by year
- 2024: 2
- FWCI
- 0.26
- Type
- journal article
- Language
- en
- Open access
- closed
- Licence
- publishingsupport.iopscience.iop.org/iop-standard/v1 (vor)
- iopscience.iop.org/info/page/text-and-data-mining (tdm)
- Locations
- Surface Topography Metrology and Properties (publishedVersion)
- Topics
- Physical Sciences › Materials Science › Surfaces, Coatings and Films › High-Temperature Coating Behaviors
- Physical Sciences › Engineering › Mechanical Engineering › High Temperature Alloys and Creep
- Physical Sciences › Materials Science › Materials Chemistry › Corrosion Behavior and Inhibition
- Keywords
- hot corrosion, plasma-sprayed coatings, Al2O3-TiO2 coatings, NiCrAlY bond coat, corrosion kinetics, oxide scale, protective oxide scale, weight gain, iron oxide formation
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.