The DOI matches its Crossref record; 10 of the 10 references it cites were found in a registry or an index.
Design and optimization of medium frequency, medium voltage transformers
Abstract
Medium voltage, medium frequency transformers (MFTs) are much smaller in size and weight compared to conventional low frequency transformers. The MFTs are very attractive for applications where full control of the power flow and high power density are required, such as power electronic interface in smart grids and traction converter system. With reduced size, the optimal design of MFTs becomes more challenging due to the high isolation requirement and thermal stress. This paper presents a design and optimization methodology for MFTs with emphasis on thermal and insulation design. The improved thermal model for multi-layer windings consisting of litz-wire and the analytical calculation of maximum electric field in core window area are included in the optimization process. By using the methodology, the optimal designs of a 25kW/4 kHz MFT with two commonly used core materials are compared. The possibility of volume reduction by increasing the operating frequency is also investigated.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“The primary design challenge for high-power MFTs is to balance the competing objectives including reliable electrical insulation, high efficiency, high power density, and superior thermal performance [2-7].”
From Design and Optimization of a 200-kW Medium-Frequency Transformer for Medium-Voltage SiC PV Inverters (2021) · cites this paper as [5]
Citations
Cites
A Charge Simulation Method for the Calculation of High Voltage Fields
Singer, H., Steinbigler, H., & Weiss, P. (1974) · IEEE Transactions on Power Apparatus and Systems · doi:10.1109/tpas.1974.293898 · Cited by 678 · cited 1×
“For safety reason, Emax is limited to 8.75 kV/mm, which is 25% of the dielectric strength of the epoxy resin[14].”
BackgroundInfluentialMedium frequency topology in railway applications
Steiner, M., & Reinold, H. (2007) · 2007 European Conference on Power Electronics and Applications · doi:10.1109/epe.2007.4417570 · Cited by 249 · cited 1×
“Previous research focusing on MFT design has been introduced in [1] [2] [3] for traction applications and in [4] [5] for renewable energy and smart grid applications.”
Optimized design of medium frequency transformers with high isolation requirements
Ortiz, G., Biela, J., & Kolar, J. W. (2010) · IECON 2010 - 36th Annual Conference on IEEE Industrial Electronics Society · doi:10.1109/iecon.2010.5675240 · Cited by 159 · cited 1×
“In [7], different core materials are considered for design and temperature calculation is included in optimization process.”
BackgroundSelf-citationAn actively cooled high power, high frequency transformer with high insulation capability
Heinemann, L. (2003) · APEC. Seventeenth Annual IEEE Applied Power Electronics Conference and Exposition (Cat. No.02CH37335) · doi:10.1109/apec.2002.989270 · Cited by 135 · cited 1×
“Previous research focusing on MFT design has been introduced in [1] [2] [3] for traction applications and in [4] [5] for renewable energy and smart grid applications.”
Ortiz, G., Leibl, M., Kolar, J. W., & Apeldoorn, O. (2013) · 2013 IEEE 10th International Conference on Power Electronics and Drive Systems (PEDS) · doi:10.1109/peds.2013.6527217 · Cited by 126 · cited 1×
“Similar value of power density has been achieved in [20] for a MFT based on ferrite and operating at 20 kHz.”
MethodDu, Y., Baek, S., Bhattacharya, S., & Huang, A. Q. (2010) · Annual Conference of the IEEE Industrial Electronics Society (IECON) · doi:10.1109/iecon.2010.5674828 · Cited by 120 · cited 1×
“Previous research focusing on MFT design has been introduced in [1] [2] [3] for traction applications and in [4] [5] for renewable energy and smart grid applications.”
Multiphysical Characterization of Medium-Frequency Power Electronic Transformers
Villar, I. (2010) · Infoscience (Ecole Polytechnique Fédérale de Lausanne) · doi:10.5075/epfl-thesis-4622 · Cited by 92 · cited 3×
“Furthermore, the circular length of each winding layer and gap between layers are calculated separately instead of using a common mean length.”
BackgroundMethodInfluentialDesign considerations for medium-frequency power transformers in offshore wind farms
Meier, S., Kjellqvist, T., Norrga, S., & Nee, H. (2009) · European Conference on Power Electronics and Applications · Cited by 56
Design considerations for a medium frequency transformer in a line side power conversion system
Kjellqvist, T., Norrga, S., & Östlund, S. (2004) · IEEE Power Electronics Specialists Conference (PESC) · doi:10.1109/pesc.2004.1355834 · Cited by 52 · cited 1×
“Previous research focusing on MFT design has been introduced in [1] [2] [3] for traction applications and in [4] [5] for renewable energy and smart grid applications.”
Analytical model for the thermal resistance of windings consisting of solid or litz wire
Jaritz, M., & Biela, J. (2013) · European Conference on Power Electronics and Applications · doi:10.1109/epe.2013.6634624 · Cited by 40 · cited 2×
“This is done by using 100× 4 simulation charges and calculating the E-field value of 4 contour points for each selected conductor.”
BackgroundMethodInfluentialSelf-citation
Research works printed but not linked: 2
- koch, 1968, Berechnung der kapazit?at von spulen, insbesondere in schalenkernen, Volvo Berichte, 14, 99
- wallmeier, 2001, Automatisierte Optimierung von Induktiven Bauelementen Fr Stromrichteranwendungen
Cited by
Kumar, D., Zare, F., & Ghosh, A. (2017) · IEEE Access · doi:10.1109/access.2017.2705914 · Cited by 751
“The DC-DC converter can operate at higher frequency range (few 100 Hz to kHz), and thus a considerable reduction in reactive component size can also be achieved [35], [36].”
BackgroundHigh-Frequency Transformer Design for Modular Power Conversion From Medium-Voltage AC to 400 VDC
Zhao, S., Li, Q., Lee, F. C., & Li, B. (2018) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2017.2774440 · Cited by 231
“Shuai and Biela proposed a time saving method to quickly figure out maximum electrical field which is helpful but some aspects are not included [18].”
BackgroundMethodPower Electronic Transformer-Based Railway Traction Systems: Challenges and Opportunities
Feng, J., Chu, W. Q., Zhang, Z., & Zhu, Z. Q. (2017) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2017.2685464 · Cited by 229
Power electronic technologies for flexible DC distribution grids
Doncker, R. W. D. (2014) · International Power Electronics Conference (IPEC) · doi:10.1109/ipec.2014.6869670 · Cited by 158
Design and Optimization of a 200-kW Medium-Frequency Transformer for Medium-Voltage SiC PV Inverters
Guo, Z., Yu, R., Xu, W., Feng, X., & Huang, A. Q. (2021) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2021.3059879 · Cited by 115
Metadata
- Authors
- Shuai, P., & Biela, J.
- Affiliations
- ETH Zurich (CH)
- ORCID
- Biela, Jurgen
- Venue
- 2013 15th European Conference on Power Electronics and Applications (EPE)
- Publisher
- IEEE
- Published
- 2013-09
- Pages
- 1-10
- OpenAlex
- W2071652746
- Cited by
- 43
- References
- 10
- Citations by year
- 2025: 2 · 2024: 2 · 2023: 1 · 2022: 2 · 2021: 5 · 2020: 9 · 2019: 4 · 2018: 3 · 2017: 6 · 2016: 2 · 2015: 1 · 2014: 6
- FWCI
- 3.65
- Type
- conference paper
- Language
- en
- Open access
- closed
- Locations
- European Conference on Power Electronics and Applications (publishedVersion)
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Advanced DC-DC Converters
- Physical Sciences › Materials Science › Electronic, Optical and Magnetic Materials › Magnetic Properties and Applications
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Induction Heating and Inverter Technology
- Keywords
- medium frequency transformer, medium-voltage transformers, transformer design optimization, thermal modeling, insulation design, Litz wire, multi-layer winding, maximum electric field, core materials, volume reduction, traction converter, power electronic interfaces, smart grid
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Design and optimization of medium frequency, medium voltage transformers. https://app.cochat.ai/papers/10.1109/epe.2013.6634423
- The paper
- Shuai, P., & Biela, J. (2013). Design and optimization of medium frequency, medium voltage transformers. 2013 15th European Conference on Power Electronics and Applications (EPE). https://doi.org/10.1109/epe.2013.6634423
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.