Current Sensing Techniques: A Review
The DOI matches its Crossref record; 62 of the 63 references it cites were found in a registry or an index.
Abstract
This paper provides a thorough review of state-of-the-art current sensing techniques. It catalogues the current sensors according to the underlying physical principle in order to point out their strengths and weaknesses.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“The measurement range is limited by the accuracy of the voltage measurement [10,31].”
From Battery Management System Hardware Concepts: An Overview (2018) · cites this paper as [10]
In the citing paper
“However, solely relying on coulomb counting for precise SOC determination appears risky because current sensors are also non-ideal systems that underlie a certain drift-, offset-and temperature-error (see e.g., [10]).”
From Battery Management System Hardware Concepts: An Overview (2018) · cites this paper as [10]
In the citing paper
“Furthermore, high load current bypassing the low-side monitor-for instance caused by accidental short-circuit-cannot be detected [10].”
From Battery Management System Hardware Concepts: An Overview (2018) · cites this paper as [10]
In the citing paper
“A further drawback of this measuring method is that the output signal of a Hall effect sensor has a large temperature drift [10] that needs to be compensated in the sensor module or the signal processing chain.”
From Battery Management System Hardware Concepts: An Overview (2018) · cites this paper as [10]
Citations
Cites
Giant Magnetoresistance of (001)Fe/(001)Cr Magnetic Superlattices
Baibich, M. N., Broto, J. M., Fert, A., Van Dau, F. N., Petroff, F., Etienne, P., Creuzet, G., Friederich, A., & Chazelas, J. (1988) · Physical Review Letters · doi:10.1103/physrevlett.61.2472 · Cited by 9,415 · cited 1×
“The discoverers Gruenberg and Fert received the 2007 Physics Nobel Prize for this work [48], [49].”
BackgroundEnhanced magnetoresistance in layered magnetic structures with antiferromagnetic interlayer exchange
Binasch, G., Grünberg, P., Saurenbach, F., & Zinn, W. (1989) · Physical Review B · doi:10.1103/physrevb.39.4828 · Cited by 4,347 · cited 1×
“The discoverers Gruenberg and Fert received the 2007 Physics Nobel Prize for this work [48], [49].”
BackgroundGiant magnetic tunneling effect in Fe/Al2O3/Fe junction
Miyazaki, T., & Tezuka, N. (1995) · Journal of Magnetism and Magnetic Materials · doi:10.1016/0304-8853(95)90001-2 · Cited by 1,917 · cited 1×
“Using the TMR effect, resistance changes up to 230% at room temperature have been reported [59], [60].”
BackgroundReview of the present status of optical fiber sensors
Lee, B. (2003) · Optical Fiber Technology · doi:10.1016/s1068-5200(02)00527-8 · Cited by 1,736 · cited 4×
“35, that allows it to generate a linear output from the detected signal by building the ratio of the first and second harmonic amplitude level [62], [70].”
BackgroundMethodInfluentialMagnetic sensors and their applications
Lenz, J., & Edelstein, S. (2006) · IEEE Sensors Journal · doi:10.1109/jsen.2006.874493 · Cited by 1,312 · cited 5×
“It has to be noted that this is just one example of a structure that exhibits the GMR effect [33], [50].”
BackgroundInfluentialInductance Calculations Working Formulas and Tables
Snyder, J. N., & Grover, F. C. (1964) · Mathematics of Computation · doi:10.2307/2003443 · Cited by 1,309 · cited 1×
“In reality, the parasitic inductance is determined by the mutual inductance between loop built by the sense wires and the loop built by the main current [1].”
Background230% room-temperature magnetoresistance in CoFeB∕MgO∕CoFeB magnetic tunnel junctions
Djayaprawira, D. D., Tsunekawa, K., Nagai, M., Maehara, H., Yamagata, S., Watanabe, N., Yuasa, S., Suzuki, Y., & Ando, K. (2005) · Applied Physics Letters · doi:10.1063/1.1871344 · Cited by 967 · cited 1×
“Using the TMR effect, resistance changes up to 230% at room temperature have been reported [59], [60].”
BackgroundFiber Optic Sensors: An Introduction for Engineers and Scientists
(2011) · Wiley eBooks · doi:10.1002/9781118014103 · Cited by 783 · cited 1×
“Linear birefringent material behaves vice versa [61].”
Giant magnetic field dependent impedance of amorphous FeCoSiB wire
Beach, R. S., & Berkowitz, A. E. (1994) · Applied Physics Letters · doi:10.1063/1.111170 · Cited by 650
Primdahl, F. (1979) · Journal of Physics E: Scientific Instruments · doi:10.1088/0022-3735/12/4/001 · Cited by 499
Research works printed but not linked: 15
- ziegler, 2008, An isolated current to voltage voltage to voltage converter
- tipler, 2005, Understanding Hall effect devices
- tipler, 2005, An introduction to the Hall effect
- udd, 1991, Fiber Optic SensorsAn Introduction for Engineers and Scientists
- tipler, 1991, Physics for Scientists and Engineers
- ma, 2004, Isolated Current and Voltage Transducers
- baibich, 1997, The giant magnetoresistive head A giant leap for IBM research
- kowina, 2005, high dynamic magnetic beam current measurement by means of optimized magnet-resistance (mr) sensor engineering, Proc 7th Eur Workshop on Beam Diagnostics and Instrumentation for Particle Accelerators DIPAC 2005, 102
- beltran, 2005, AA and AB-series analog sensors datasheet
- mammano, 2005, High-side current-sense measurement
- spaziani, 1997, Using copper PCB etch for low value resistance
- spaziani, 2005, Cu-ETP copper specification
- ray, 2005, RCTrms Rogowski coil datasheet
- mammano, 1997, current sensing solutions for power supply designer, Power Design Seminar SEM 1200
- dezuari, 2003, Basic introduction to the use of magnetoresistive sensors
Cited by
Items 301–400 of 775
Mușuroi, C., Volmer, M., Oproiu, M., Neamtu, J., & Helerea, E. (2022) · Electronics · doi:10.3390/electronics11233888 · Cited by 8
Constantin, G., Maroșan, I.-A., Crenganiș, M., BOTEZ, C., Gîrjob, C., Biriș, C., Chicea, A. L., & Bârsan, A. (2023) · Machines · doi:10.3390/machines11030385 · Cited by 13
Linear birefringence and imperfect quarter wave plate effects on optic-fiber current sensor
Ding, Y., Yi, D., Zhu, J., Zheng, B., Zhang, D., & Hu, W. (2011) · Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE · doi:10.1117/12.904480 · Cited by 8
“INTRODUCTION During the past decades, optical current sensor (OCS) based on Faraday effect has attracted wide attention [1].”
BackgroundImproving Magnetooptical Faraday Effect of maghemite/silica nanocomposites
Garcı́a, R., Ramírez-del-Solar, M., Gonzalez-Leal, J. M., Blanco, E., & Domínguez, M. (2015) · Materials Chemistry and Physics · doi:10.1016/j.matchemphys.2014.12.049 · Cited by 8
Non-conventional instrument current transformer test set for industrial applications
Crotti, G., Gallo, D., Giordano, D., Landi, C., & Luiso, M. (2014) · IEEE International Workshop on Applied Measurements for Power Systems (AMPS) · doi:10.1109/amps.2014.6947699 · Cited by 8
“Typical NCCIT outputs are voltage signals with rated value ranging from some millivolts to some volts [6], [7], or current signals, with rated output from tens to hundreds of milliamperes [6], [8].”
BackgroundArduino Based Power Meter Using Instantaneous Power Calculation Method
Tiong, M. C., & Hamdan, D. (2015) · UMP Institutional Repository (Universiti Malaysia Pahang) · Cited by 8
Design of a portable smart connected solar-powered charger for consumer electronics
Dallard, M., Forest, A., & Shabani, A. (2017) · Conference proceedings - Canadian Conference on Electrical and Computer Engineering · doi:10.1109/ccece.2017.7946781 · Cited by 8
“Although Hall Effect sensors use less power, a trade-off exists between Hall plate thickness, which increases accuracy, and power loss [5].”
BackgroundMethodDie Level Sensor Integration in SiC Power Modules
Sheng, M., Alvi, M. H., & Lorenz, R. D. (2018) · IEEE Transportation Electrification Conference and Expo · doi:10.1109/itec.2018.8450247 · Cited by 8
“Most module integrated current sensing utilizes shunt resistors, which are not galvanically isolated [1-8].”
BackgroundMethod20 MHz Integrated Current Sensing for WBG Systems with EMI Suppression
Sheng, M., Alvi, M. H., & Lorenz, R. D. (2018) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce.2018.8557384 · Cited by 8
“In silicon (Si) based power converters, current sensors with a magnetic core [1] are commonly used for closed-loop control.”
BackgroundGao, X., & Zhao, B. (2019) · Optics and Lasers in Engineering · doi:10.1016/j.optlaseng.2019.06.026 · Cited by 8
An Integrated TMR-Based Current Sensing Solution for WBG Power Modules and Converters
Vala, S. S., Mirza, A. B., & Luo, F. (2024) · IEEE Transactions on Components Packaging and Manufacturing Technology · doi:10.1109/tcpmt.2024.3392483 · Cited by 7
“The minor resistance deviation ratio means low SNR, the AMR’s main weakness [20], [22].”
InfluentialAn, N., Xu, P., Yang, Z., Liu, K., Deng, S., Wang, Y., Sun, X., & Peng, B. (2025) · Measurement · doi:10.1016/j.measurement.2025.117247 · Cited by 7
Zhu, K., & Pong, P. W. T. (2016) · International Symposium on Next-Generation Electronics · doi:10.1109/isne.2016.7543342 · Cited by 7
Laser-Induced Abnormal Cryogenic Magnetoresistance Effect in a Corbino Disk
Dong, X., Zheng, D., Yuan, M., Niu, Y., Liu, B., & Wang, H. (2020) · Physical Review Applied · doi:10.1103/physrevapplied.13.064050 · Cited by 7
Ravi, L., Liu, J., Schmalz, S., Schroedermeier, A., Burgos, R. P., & Dong, D. (2023) · Conference proceedings/Conference proceedings - IEEE Applied Power Electronics Conference and Exposition · doi:10.1109/apec43580.2023.10131423 · Cited by 7
“Magnetoresistive sensors, specifically those based on anisotropic magnetoresistance (AMR) and giant magnetoresistance (GMR), have advantages of small physical size, low cost, high sensitivity and good linearity with less drift [1], [10].”
BackgroundA Novel Tunneling Magnetoresistive Current Sensor Based on Reference Magnetic Field Source
Qi, Z., Wei, P., Liu, C., Huang, H., Xu, H., & Li, X. (2024) · IEEE Sensors Letters · doi:10.1109/lsens.2024.3350154 · Cited by 7
Electrical ammeter based on spin-valve sensor
Sánchez, J., Ramírez, D., Amaral, J., Cardoso, S., & Freitas, P. P. (2012) · Review of Scientific Instruments · doi:10.1063/1.4759020 · Cited by 7
A non-invasive electric current sensor employing a modified shear-mode cymbal transducer
He, W., Lu, Y., Qu, C., & Peng, J. (2016) · Sensors and Actuators A Physical · doi:10.1016/j.sna.2016.02.015 · Cited by 7
A State-of Art of Creative Sensor Devices Utilizing Magneto- Rheological Fluids
Kaluvan, S., Kim, H.-C., Oh, J.-S., & Choi, S. (2015) · International Journal of Mechanical Systems Engineering · doi:10.15344/2455-7412/2015/108 · Cited by 7
“Using the same resonant concept, an attempt is made to design current sensor using magneto rheological fluids [13] as the information regarding current flow is very much required in electrical and electronics applications [14].”
Singh, S., Mandal, D., Bakkaloğlu, B., & Kiaei, S. (2019) · IEEE Transactions on Circuits and Systems I Regular Papers · doi:10.1109/tcsi.2019.2897049 · Cited by 7
“current [18] and obtaining the product of sensed current with the sensed voltage is expensive in terms of the bill of material of off-chip components, die area, and power consumption.”
BackgroundDesign of an Integrated Air Coil for Current Sensing
Kuwabara, Y., Wãda, K., Guichon, J., Schanen, J., & Roudet, J. (2020) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2020.2977102 · Cited by 7
“However, it is difficult to use conventional current sensors [14] in recent power converter circuits because the power circuit layout should be modified and stray inductance increases significantly, which is undesirable for WBG devices.”
BackgroundCompact Galvanically Isolated Architectures for Low-Power DC-DC Converters with Data Transmission
Ragonese, E., Parisi, A., Spina, N., & Palmisano, G. (2021) · Electronics · doi:10.3390/electronics10192328 · Cited by 7
“A common application is to provide an analog-to-digital converter (ADC) with isolated power, along with low data rate communication [2–4], as represented in Figure 2.”
BackgroundBiswas, K., & Ray, O. (2022) · IEEE Sensors Letters · doi:10.1109/lsens.2022.3200836 · Cited by 7
“The sensors used for the measurement of current can be classified into invasive and noninvasive types [6], [7].”
MethodA novel inductively coupled RLC damping scheme for eliminating switching oscillations of SiC MOSFET
Li, J., Yang, X., Xu, M., Wang, X., & Heng, K. (2023) · IET Power Electronics · doi:10.1049/pel2.12485 · Cited by 7
Characterizing Semiconductor Devices for All-Electric Aircraft
Elwakeel, A., McNeill, N., Alzola, R. P., Surapaneni, R. K., Galla, G., Ybanez, L., Zhang, M., & Yuan, W. (2023) · IEEE Access · doi:10.1109/access.2023.3279088 · Cited by 7
“were considered [19] as summarized in Table 5.”
BackgroundSub-mA current measurement by means of GMR sensors and state of the art lock-in amplifiers
García-Romeo, D., Medrano, N. J., Calvo, B., Martínez, P. A., Cubells‐Beltrán, M., Reig, C., Cardoso, S., & Freitas, P. P. (2015) · IEEE International Conference on Industrial Technology (ICIT) · doi:10.1109/icit.2015.7125600 · Cited by 7
“The measurement of electric current is, nowadays, a matter of concern [1, 2].”
BackgroundConcept and experimental evaluation of a novel DC- 100MHz wireless oscilloscope
Lobsiger, Y., Ortiz, G., Bortis, D., & Kolar, J. W. (2014) · International Power Electronics Conference (IPEC) · doi:10.1109/ipec.2014.6869755 · Cited by 7
Villani, C., Balsamo, D., Brunelli, D., & Luca Benini, C. (2015) · Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE · doi:10.1117/12.2181332 · Cited by 7
Rogowski Coil for Current Measurement in a Cryogenic Environment
Ma, T., Dai, S., Zhang, J., & Zhao, L. (2015) · Measurement Science Review · doi:10.1515/msr-2015-0012 · Cited by 7
Flugate Sensor With Pulse Feedback
Ripka, P., Přibil, M., Schäffer, V., & Snoeij, M. F. (2016) · IEEE Transactions on Magnetics · doi:10.1109/tmag.2016.2524516 · Cited by 7
“Some applications, such as current sensing [1], [2] or non-destructive evaluation [3], require extending this range while keeping the high sensitivity and resolution of fluxgate compared with other types of magnetic sensors [4].”
BackgroundPiezoelectric ceramic sensor (PZT) applied to electric current measurements
Júnior, M. H. B., Magalhães, A. L., Bastos, A. M., Sales, A. J. M., Gouveia, D. X., Kamshilin, A. A., Ferreira, A. D. C., Guimarães, G. D. F., Sombra, A. S. B., & Menezes, J. W. M. (2018) · Microsystem Technologies · doi:10.1007/s00542-018-3998-8 · Cited by 7
“Techniques based in the Hall-effect, the magnet-resistance effect, or fiber-optics also provide possibilities for emerging technologies for current measurements methods (Anton and Sodano 2007; Kumae et al. 2011; Ziegler et al. 2009; Xiao et al. 2003).”
BackgroundGMR-Based Integrated Current Sensing in SiC Power Modules With Phase Shift Error Reduction
Sheng, M., Alvi, M. H., & Lorenz, R. D. (2020) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2020.3028275 · Cited by 7
Degel, J. P., Haehnlein, S., Kloeffer, C., & Doppelbauer, M. (2020) · International Conference on Electrical Machines (ICEM) · doi:10.1109/icem49940.2020.9270920 · Cited by 7
Modeling Stray Capacitances of High-Voltage Capacitive Dividers for Conventional Measurement Setups
Mingotti, A., Costa, F., Peretto, L., Tinarelli, R., & Mazza, P. (2021) · Energies · doi:10.3390/en14051262 · Cited by 7
Kim, W., & Choi, K. (2022) · Journal of Energy Storage · doi:10.1016/j.est.2022.104726 · Cited by 7
A High-Voltage-Compliant Current-to-Digital Sensor for DC–DC Converters in Standard CMOS Technology
Marti-Arbona, E., Mandal, D., Bakkaloğlu, B., & Kiaei, S. (2016) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2016.2562108 · Cited by 7
“Other methods include inductor dc resistance [15]–[17], inductor/coil coupling, transformers, and Hall effect sensors [12], [18]–[21].”
BackgroundMethodOnline Estimation of the Current Ripple on a Saturating Ferrite-Core Inductor in a Boost Converter
Lodi, M., & Oliveri, A. (2020) · Sensors · doi:10.3390/s20102921 · Cited by 7
“Current mode control of course requires measurements of the inductor current, which can be basically performed through shunt resistors, mirroring circuits, or Hall effect sensors [4,5].”
Li, G.-F., Gao, C., Du, Y., Li, D., Peng, F., Men, S., Tan, Y., & Liu, S. (2024) · IEEE Sensors Journal · doi:10.1109/jsen.2024.3520384 · Cited by 6
Noninvasive Flexible Current Probe as a Diagnosis Tool Inside a PWM Chopper Module
Luo, C., Ding, R., Fang, W., Wang, L., Chen, Y., & Fernández, R. (2024) · IEEE Transactions on Instrumentation and Measurement · doi:10.1109/tim.2024.3381702 · Cited by 7
“The electromagnetic immunity diagnostic tools for inter-fered voltage or current measurement generally adopt traditional contact probes connected to tested circuit [6], [7], [8], [9].”
BackgroundLuo, R., Qin, Y., Zhou, Y., Li, F., & Wang, R. (2024) · Progress In Electromagnetics Research M · doi:10.2528/pierm24022002 · Cited by 6
“In recent years, the advancement of magnetic field sensor technology has led to an increasing number of studies exploring the application of sensors (such as Hall, tunnel magneto-resistive, and giant magneto-resistive sensors) for current measurement [4].”
BackgroundPhilipps, D. A., & Peftitsis, D. (2024) · IET Power Electronics · doi:10.1049/pel2.12699 · Cited by 6
A Closed-Loop Compensated Rogowski Coil Current Sensor for Three-Phase Inverter
Xin, Z., Yao, Y., Kang, J., Li, Q., Zhou, Z., & Shi, Y. (2024) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2024.3464121 · Cited by 7
“Shunt uses a tiny resistance in the main circuit to measure the voltage across the resistance, but lacks electrical isolation between input and output, which exists security risks in three-phase inverter control system [9].”
Stray Inductance Extraction Methods for Power Modules: A Comprehensive Review and Analysis
Yang, M., Xiao, Y., Ji, S., Xie, W., Zhao, Z., Sheng, C., & Yang, W. (2025) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2025.3532542 · Cited by 6
“The commonly used techniques for switching transient current measurement can be categorized into two main types [25]: 1) Rogowski coils based on EM induction, and 2) coaxial and surface-mount shunts based on Ohm’s law.”
Robustness analysis of magnetic sensor arrays for current sensing
Li, D., & Rienzo, L. D. (2011) · International Conference on Electric Power Equipment – Switching Technology · doi:10.1109/icepe-st.2011.6122908 · Cited by 6
Nibir, S. J., & Parkhideh, B. (2017) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce.2017.8096587 · Cited by 6
“Hall-effect sensors are widely used in different applications as they can respond to both AC and DC fields and significant performance improvement has been observed over the years [1]-[3].”
BackgroundDesign of resonance based DC current sensor using BAW quartz resonators
Pisupati, S., Kundukoori, D., Mekala, N., Kaluvan, S., & Zhang, H. (2018) · Sensors and Actuators A Physical · doi:10.1016/j.sna.2018.01.006 · Cited by 6
Lee, S., Ahn, Y., Kim, T., Kim, N., & Lee, S.-C. (2018) · IEEE Sensors Journal · doi:10.1109/jsen.2018.2870296 · Cited by 6
“With shunt resistor-based methods, the voltage across a resistor with an accurately defined value is measured [4].”
MethodOptimal Self-Tuning Control for Data-Centers’ 48V-12V ZCS-STC
Sovik, G., Urkin, T., Masandilov, E. E., & Peretz, M. M. (2020) · Conference proceedings/Conference proceedings - IEEE Applied Power Electronics Conference and Exposition · doi:10.1109/apec39645.2020.9124129 · Cited by 6
“Shunt resistor, Rds,on sensing, SenseFET and current transformers [30]-[31] are all viable solutions, but require overdesign or additional protection circuitry, due to the high currents in the tanks (tens of Amps under full load conditions) and the actual low currents which are of interest at the switching moments.”
BackgroundUbiquitous Self-Powered Architecture for Fuel Cell-Based Point-of-Care Applications
Álvarez-Carulla, A., Montes-Cebrián, Y., Puig-Vidal, M., Colomer‐Farrarons, J., & Miribel‐Català, P. L. (2020) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2020.3029484 · Cited by 6
High Frequency PCB Trace Current Measurement in Power Converters Based on Tunnel Magnetoresistance
Lin, W., Shao, S., & Zhang, J. (2021) · Annual Conference of the IEEE Industrial Electronics Society (IECON) · doi:10.1109/iecon48115.2021.9589111 · Cited by 6
“Magnetic field sensors can convert static and dynamic magnetic fields into electrical signal output, hence can be used to measure both DC and AC current [1].”
BackgroundElectrical Compensation for Magnetization Distortion of Magnetic Fluxgate Current Sensor
Wei, Y., Cheng, L., Zhao, W., Xue, M., Cao, B., Chu, X., & Ye, C. (2022) · IEEE Transactions on Instrumentation and Measurement · doi:10.1109/tim.2022.3152861 · Cited by 6
A 2 MS/s Full Bandwidth Hall System with Low Offset Enabled by Randomized Spinning
Riem, R., Raman, J., & Rombouts, P. (2022) · Sensors · doi:10.3390/s22166069 · Cited by 6
A power-efficient acquisition front end for the Li-ion battery management systems
Bao, Y., & Ye, L. (2022) · Microelectronics Journal · doi:10.1016/j.mejo.2022.105598 · Cited by 6
A Dynamic Voltage-Based Current Estimation Technique for DC Motor Speed Control Applications
Hajari, S., & Ray, O. (2023) · IEEE Sensors Letters · doi:10.1109/lsens.2023.3346651 · Cited by 6
“A comparison of current sensing methods [3] indicate that current sensors typically need to be placed in path of the current for sensing, i.e., they are series-type measurements which may often require sensor insertion in current path.”
BackgroundCharacterization of Magnetoresistive Shunts and Its Sensitivity Temperature Compensation
Ramirez-Munoz, D., García-Gil, R., Cardoso, S., & Freitas, P. P. (2024) · Sensors · doi:10.3390/s24103047 · Cited by 6
“Techniques used in measuring electric current include, mainly: shunt resistors, current transformers, Rogowski coils, Hall effect sensors, and magnetoresistive (MR) sensors [3].”
BackgroundDevelopment of thin film based flexible current clamp sensor using screen-printed coil
Yamashita, T., Zhang, Y., Itoh, T., & Maeda, R. (2015) · Microsystem Technologies · doi:10.1007/s00542-015-2601-9 · Cited by 6
Neel Effect Toroidal Current Sensor
Vourch, E., Wang, Y., Joubert, P.-Y., Revol, B., Couderette, A., & Cima, L. (2012) · IEEE Transactions on Magnetics · doi:10.1109/tmag.2012.2222021 · Cited by 6
Zhang, J., Li, P., Wen, Y., He, W., Yang, J., Yang, A., Lu, C., & Li, W. (2014) · Journal of Applied Physics · doi:10.1063/1.4862081 · Cited by 6
Analytical study of high pulse current shunts
Ferrero, R., Marracci, M., & Tellini, B. (2011) · IEEE International Instrumentation and Measurement Technology Conference · doi:10.1109/imtc.2011.5944280 · Cited by 6
“Focusing on the shunt resistors, these transducers can provide very accurate current measurements over a wide frequency range, and a wide range of current amplitudes [6], [7], [8], [9].”
BackgroundMattheis, R., Diegel, M., & Weiss, R. J. (2016) · IEEE Transactions on Magnetics · doi:10.1109/tmag.2016.2582139 · Cited by 6
“Current sensing applications [4], [6]–[10] have additionally special demands for the sensor characteristics, namely, vanishing temperature coefficient (TC) of the sensitivity U / I of the sensor, linear response for low currents, and the ability to measure also large currents with then a reduced sensitivity [4], [9].”
BackgroundHwang, H., Park, D., Lee, W., Hong, K., & Kim, K. (2018) · International Conference on Electronics, Information, and Communication (ICEIC) · doi:10.23919/elinfocom.2018.8330692 · Cited by 6
“Current transformer is also not suitable for low frequency (DC) measurement [1,2].”
BackgroundCurrent Measuring Shunts for Impulse Current Test According to IEC 62305–2010
Shalamov, S. (2018) · International Conference on Ultrawideband and Ultrashort Impulse Signals · doi:10.1109/uwbusis.2018.8519984 · Cited by 6
Mönch, S., Meyer, J. M., Žukauskaitė, A., Lebedev, V., Fichtner, S., Su, J., Niekiel, F., Giese, T., Thormählen, L., Quandt, E., et al. (2022) · IEEE Sensors Letters · doi:10.1109/lsens.2022.3205853 · Cited by 6
“Electrical current sensors are essential in a multitude of applications [1], [2], for example, control of power converters [3], power metering, motor drive, and overcurrent protection.”
BackgroundTemperature compensation of fiber-optic current sensors in different regimes of operation
Müller, G. M., Frank, A., Lenner, M., Bohnert, K. M., Gabus, P., & Gülenaltin, B. (2012) · IEEE Photonics Conference · doi:10.1109/ipcon.2012.6358837 · Cited by 6
A TMR-based Integrated Current Sensing Solution for WBG Power Modules
Vala, S. S., Mirza, A. B., & Luo, F. (2024) · Conference proceedings/Conference proceedings - IEEE Applied Power Electronics Conference and Exposition · doi:10.1109/apec48139.2024.10509509 · Cited by 5
“Among various options, magnetoresistors-based current sensors like Giant Magnetoresistance (GMR) and Tunneling Mag-netoresistance (TMR) are well-suited due to their small size and high bandwidth [13], [14].”
BackgroundA Novel Method for DC Current Measurement Using Current Transformer
Hu, Y., Ottoboni, R., & Li, J. (2024) · IEEE Transactions on Instrumentation and Measurement · doi:10.1109/tim.2024.3463012 · Cited by 5
“Their installation entails intricacy, demanding meticulous alignment and rigorous calibration procedures [18].”
BackgroundSmart electrical protection method for industries operations
Siddique, A. H., Barkat, B., & Poshtan, M. (2013) · IEEE Electric Ship Technologies Symposium (ESTS) · doi:10.1109/ests.2013.6523766 · Cited by 5
Optical sensors technologies evolution applied for power quality monitoring in the medium-voltage
Rosolem, J. B., Floridia, C., Bassan, F. R., da Costa, E. F., Barbosa, C. F., Dini, D. C., Penze, R. S., Marques, F. L. D. R., & Teixeira, R. A. V. (2018) · Fiber Optic Sensors and Applications · doi:10.1117/12.2304641 · Cited by 5
“There are some electric/electronic sensors that can attend the IEC specifications [36], e.”
BackgroundRodriguez-Echevarria, A., Lopez-Perez, C., & Correa-Betanzo, C. (2019) · IEEE Transactions on Instrumentation and Measurement · doi:10.1109/tim.2019.2957893 · Cited by 5
“Those current-sensing methods can be classified based on physical principles [1], for example, Ohm’s law, Faraday’s”
MethodA High-Bandwidth Resistive Current Sensing Technology for Breakers and Desaturation Protection
Gao, B., Mehrotra, U., & Hopkins, D. C. (2019) · IEEE Workshop on Wide Bandgap Power Devices and Applications · doi:10.1109/wipda46397.2019.8998767 · Cited by 5
“However, overshooting is one of the biggest problems for resistive sensing, especially with fast WBG switches switching at high di/dt [1].”
BackgroundHigh Current, High Bandwidth Current Measurement Techniques
Zhang, T., Shelton, E., Shillaber, L., & Palmer, P. (2020) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce44975.2020.9235469 · Cited by 5
“These sensors fall into two categories[3][4]: (A) Those that measure magnetic field as a proxy for current in a conductor, and (B) those that measure voltage drop as a proxy for current.”
BackgroundYang, X., Chen, M., & Jia, Z. (2021) · Review of Scientific Instruments · doi:10.1063/5.0030868 · Cited by 5
Performance and Noise Trade-off for SC-based Power Side-Channel Attack Detection Circuits
Kaushik, N., & Hu, J. R. (2021) · IEEE International Midwest Symposium on Circuits and Systems (MWSCAS) · doi:10.1109/mwscas47672.2021.9531778 · Cited by 5
Qian, S., Deng, H., Chen, C., Huang, H., Liang, Y., Guo, J., Hu, Z., Si, W., Wang, H., & Li, Y. (2022) · IEEE International Electrical and Energy Conference (CIEEC) · doi:10.1109/cieec54735.2022.9846524 · Cited by 5
“The commonly used current sensors include current shunt, current transformer, Rogowski coil, optical fiber current transducer and magneto-resistive sensors [1,2].”
MethodLiang, S., Yang, M., Yang, G., Wang, L., Cai, X., & Zhou, Y. (2023) · Sensors · doi:10.3390/s23125654 · Cited by 5
Li, S., Huang, S., Li, L., Su, Q., Zeng, G., & Wu, T. (2024) · Sensors and Actuators A Physical · doi:10.1016/j.sna.2024.115029 · Cited by 5
Design and Development of Hybrid Current Sensors for Wide-Bandgap Power Electronics Applications
Sirat, A. P., Niakan, H., Gafford, J. R., & Parkhideh, B. (2024) · Conference proceedings/Conference proceedings - IEEE Applied Power Electronics Conference and Exposition · doi:10.1109/apec48139.2024.10509520 · Cited by 5
“The most accurate magnetic field detectors are generally considered FG magnetometers [3, 39], and with the advent of micro-FG, the size and implementation complexity issues have been overcome, and the Texas Instruments DRV425 is considered one of the latest on-chip FG sensors available Furthermore,…”
BackgroundLuo, C., Ding, R., Fang, W., Shao, W., Li, J., Wang, L., Chen, Y., & Fernández, R. (2024) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2024.3401211 · Cited by 6
“For industrial electronic modules, the diagnostic tests generally adopt traditional contact probes connected to tested circuit [5], [6], [7], [8], which may have an impact on the tested device and also increases the testing difficulty and inconvenience.”
New Side-Looking Rogowski Coil Sensor for Measuring Large-Magnitude Fast Impulse Currents
Metwally, I. A. (2014) · Sensing and Imaging · doi:10.1007/s11220-014-0100-1 · Cited by 5
Improved AC current measurement approach in multiphase cable using proper orthogonal decomposition
Bourkeb, M., Ondel, O., Scorretti, R., Joubert, C., Morel, L., & Yahoui, H. (2013) · The European Physical Journal Applied Physics · doi:10.1051/epjap/2013120436 · Cited by 5
Experimental verification of the linear current transformer model
Chau, G. S. S., Ziegler, S., Iu, H. H., & Daniyal, H. (2008) · UWA Profiles and Research Repository (University of Western Australia) · Cited by 5
Self-citationMicrocontroller power consumption measurement based on PSoC
Jankovic, S. P., & Drndarević, V. (2016) · Telfor Journal · doi:10.5937/telfor1601044j · Cited by 5
Tape-wound Rogowski coil for measuring large-magnitude pulsed currents
Metwally, I. A. (2016) · Instruments and Experimental Techniques · doi:10.1134/s0020441216020238 · Cited by 5
High immunity wafer-level measurement of MHz current
Dąbek, M., Wiśniowski, P., Kalabiński, P., Wrona, J., Cardoso, S., & Freitas, P. P. (2016) · Measurement · doi:10.1016/j.measurement.2016.08.025 · Cited by 5
Birefringence Variation Independent Fiber-Optic Current Sensor Using Real-Time SOP Measurement
Liu, Y., Ma, L., & He, Z. (2017) · IEEE photonics journal · doi:10.1109/jphot.2017.2746764 · Cited by 5
“Fiber-optic current sensor (FOCS), employing the Faraday effect for current measurement, has many advantages such as good insulation, resistance to electromagnetic interference and light in weight [1].”
BackgroundCurrent Transducer Delay for Electric Machine Drives in Aviation
Lee, A., & Robert, E. (2018) · IEEE International Conference on Electro Information Technology · doi:10.1109/eit.2018.8500092 · Cited by 5
“State-of-the-art studies have explored the sensing accuracy [19], sensing bandwidth [20], EMI-related issues [21], and thermal-related issues [22] of various types of current transducers.”
BackgroundDelay Mitigation in High Frequency Dual Current Programmed Mode Control GaN-Based ZVS Inverter
Sabi, K., & Costinett, D. J. (2019) · IEEE ... Workshop on Control and Modeling for Power Electronics · doi:10.1109/compel.2019.8769704 · Cited by 7
“The package of a typical SMD shunt resistor and the connection of the sensed wires or PCB traces determine the parasitic inductance [12].”
BackgroundCascoded GaN half-bridge with 17 MHz wide-band galvanically isolated current sensor
Majima, H., Ishihara, H., Ikeuchi, K., Ogawa, T., Sawahara, Y., Ogawa, T., Takaya, S., Onizuka, K., & Watanabe, O. (2021) · Japanese Journal of Applied Physics · doi:10.35848/1347-4065/ac4446 · Cited by 5
A Compact Reconfigurable Resonator-Based Direct Current Sensing System
Zou, X., Yaqoob, U., Hussein, H., Salama, K. N., & Fariborzi, H. (2022) · Journal of Microelectromechanical Systems · doi:10.1109/jmems.2022.3216912 · Cited by 5
“As summarized in [11] and [12], various current sensors with different design approaches and operating mechanisms have recently been developed, including the resistive shunt current [10], Hall [11], inductive [12], and Rogowski coil sensors [13].”
BackgroundAn autonomous current-sensing system for elecric cord monitoring using magnetoelectric sensors
Zhang, J., Wul, J., Yang, Q., Wang, X., Zheng, X., & Cao, L. (2017) · IEEE International Electric Machines & Drives Conference (IEMDC) · doi:10.1109/iemdc.2017.8002250 · Cited by 5
“In the last decades, the ever-increasing demand for protection, measurement and monitoring of electricity usage in residential and commercial circumstances has propelled the exploration of current-sensing techniques [1, 2].”
BackgroundBus bar embedded rogowski coil
Kuwabara, Y., Wãda, K., Guichon, J., Schanen, J., & Roudet, J. (2018) · Conference proceedings/Conference proceedings - IEEE Applied Power Electronics Conference and Exposition · doi:10.1109/apec.2018.8341417 · Cited by 6
de Nazaré, F. V. B., & Werneck, M. M. (2010) · IEEE PES Transmission and Distribution Conference and Exhibition · doi:10.1109/tdc.2010.5484461 · Cited by 5
He, W., Zhang, J., Qu, C., Wu, J., & Peng, J. (2016) · IEEE Transactions on Magnetics · doi:10.1109/tmag.2016.2526055 · Cited by 5
“Current transformers have the defects of hysteresis and magnetic saturation in the large current condition [5].”
BackgroundCurrent Sensing Techniques: Principles and Readouts
Kashmiri, M. (2019) · Springer eBooks · doi:10.1007/978-3-030-25267-0_9 · Cited by 5
Smart Metering and Demand‐Side Integration
Ekanayake, J. B., Liyanage, K. M., Wu, J., Yokoyama, A., & Jenkins, N. (2012) · Smart Grid · doi:10.1002/9781119968696.ch5 · Cited by 5
Measurement-based analysis of packaged X-Hall current sensors for automotive applications
Mengozzi, M., Syeda, S. F., Ferretti, J., Gibiino, G. P., Crescentini, M., & Traverso, P. A. (2025) · Measurement · doi:10.1016/j.measurement.2025.119559 · Cited by 5
Large bandwidth and dynamic range current sensor based on micro-PCB Rogowski coil
Wang, L., Han, Y., Ji, Y., Tang, F., Su, W., Wu, J., Guan, M., Hu, Z., Wang, Z., & Liu, M. (2024) · Measurement Science and Technology · doi:10.1088/1361-6501/ad25e9 · Cited by 4
“Unfortunately, traditional current sensors cannot fully meet the above-mentioned requirements [1, 3, 11].”
3-D Point Magnetic Field Detection for Compact Current Sensing in Three-Phase Busbars and Cables
Alvi, M. H., Sheng, M., Lorenz, R. D., & Jahns, T. M. (2019) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce.2019.8913095 · Cited by 4
“Resistive methods have the major drawbacks of thermal dependence, parasitic inductance, power loss, and lack of galvanic isolation [1].”
BackgroundHigh Precision Wide Bandwidth DC Current Transducer Based on the Platiše Flux Sensor
Platiše, U., Kanalec, T., & Mohorčič, M. (2020) · Sensors · doi:10.3390/s20154197 · Cited by 4
“, fiber-optic current sensors) [9], each with its particular advantages and drawbacks.”
BackgroundPerformance Evaluation of GMR and TMR Sensors to Estimate Current Phasors in Smart Grids
Shrawane, P., & Sidhu, T. S. (2020) · IEEE Electrical Power and Energy Conference (EPEC) · doi:10.1109/epec48502.2020.9320111 · Cited by 4
“The conventional current sensing techniques are based on few principles such as Faraday’s law of induction, Ohm’s law of resistance, Faraday’s effect and magnetic field sensing [7-13].”
Method
Metadata
- Authors
- Ziegler, S., Woodward, R. C., Iu, H. H.-C., & Borle, L. J.
- Affiliations
- The University of Western Australia (AU)
- Venue
- IEEE Sensors Journal
- Published
- 2009-04
- Volume
- 9
- Issue
- 4
- Pages
- 354-376
- ISSN
- 1530-437X (ISSN-L)
- OpenAlex
- W2127394451
- Cited by
- 774
- References
- 63
- Citations by year
- 2026: 37 · 2025: 65 · 2024: 63 · 2023: 70 · 2022: 66 · 2021: 66 · 2020: 63 · 2019: 65 · 2018: 65 · 2017: 46 · 2016: 38 · 2015: 34 · 2014: 33 · 2013: 19 · 2012: 24
- FWCI
- 11.38
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- IEEE Sensors Journal (publishedVersion)
- UWA Profiles and Research Repository (UWA) (submittedVersion)
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Magnetic Field Sensors Techniques
- Physical Sciences › Physics and Astronomy › Instrumentation › Sensor Technology and Measurement Systems
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Analog and Mixed-Signal Circuit Design
- Keywords
- current sensing, current sensor, sensor principles, sensor characteristics, current measurement
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.