Current Sensing Techniques: A Review
The DOI matches its Crossref record; 62 of the 63 references it cites were found in a registry or an index.
Abstract
This paper provides a thorough review of state-of-the-art current sensing techniques. It catalogues the current sensors according to the underlying physical principle in order to point out their strengths and weaknesses.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“The measurement range is limited by the accuracy of the voltage measurement [10,31].”
From Battery Management System Hardware Concepts: An Overview (2018) · cites this paper as [10]
In the citing paper
“However, solely relying on coulomb counting for precise SOC determination appears risky because current sensors are also non-ideal systems that underlie a certain drift-, offset-and temperature-error (see e.g., [10]).”
From Battery Management System Hardware Concepts: An Overview (2018) · cites this paper as [10]
In the citing paper
“Furthermore, high load current bypassing the low-side monitor-for instance caused by accidental short-circuit-cannot be detected [10].”
From Battery Management System Hardware Concepts: An Overview (2018) · cites this paper as [10]
In the citing paper
“A further drawback of this measuring method is that the output signal of a Hall effect sensor has a large temperature drift [10] that needs to be compensated in the sensor module or the signal processing chain.”
From Battery Management System Hardware Concepts: An Overview (2018) · cites this paper as [10]
Citations
Cites
Giant Magnetoresistance of (001)Fe/(001)Cr Magnetic Superlattices
Baibich, M. N., Broto, J. M., Fert, A., Van Dau, F. N., Petroff, F., Etienne, P., Creuzet, G., Friederich, A., & Chazelas, J. (1988) · Physical Review Letters · doi:10.1103/physrevlett.61.2472 · Cited by 9,415 · cited 1×
“The discoverers Gruenberg and Fert received the 2007 Physics Nobel Prize for this work [48], [49].”
BackgroundEnhanced magnetoresistance in layered magnetic structures with antiferromagnetic interlayer exchange
Binasch, G., Grünberg, P., Saurenbach, F., & Zinn, W. (1989) · Physical Review B · doi:10.1103/physrevb.39.4828 · Cited by 4,347 · cited 1×
“The discoverers Gruenberg and Fert received the 2007 Physics Nobel Prize for this work [48], [49].”
BackgroundGiant magnetic tunneling effect in Fe/Al2O3/Fe junction
Miyazaki, T., & Tezuka, N. (1995) · Journal of Magnetism and Magnetic Materials · doi:10.1016/0304-8853(95)90001-2 · Cited by 1,917 · cited 1×
“Using the TMR effect, resistance changes up to 230% at room temperature have been reported [59], [60].”
BackgroundReview of the present status of optical fiber sensors
Lee, B. (2003) · Optical Fiber Technology · doi:10.1016/s1068-5200(02)00527-8 · Cited by 1,736 · cited 4×
“35, that allows it to generate a linear output from the detected signal by building the ratio of the first and second harmonic amplitude level [62], [70].”
BackgroundMethodInfluentialMagnetic sensors and their applications
Lenz, J., & Edelstein, S. (2006) · IEEE Sensors Journal · doi:10.1109/jsen.2006.874493 · Cited by 1,312 · cited 5×
“It has to be noted that this is just one example of a structure that exhibits the GMR effect [33], [50].”
BackgroundInfluentialInductance Calculations Working Formulas and Tables
Snyder, J. N., & Grover, F. C. (1964) · Mathematics of Computation · doi:10.2307/2003443 · Cited by 1,309 · cited 1×
“In reality, the parasitic inductance is determined by the mutual inductance between loop built by the sense wires and the loop built by the main current [1].”
Background230% room-temperature magnetoresistance in CoFeB∕MgO∕CoFeB magnetic tunnel junctions
Djayaprawira, D. D., Tsunekawa, K., Nagai, M., Maehara, H., Yamagata, S., Watanabe, N., Yuasa, S., Suzuki, Y., & Ando, K. (2005) · Applied Physics Letters · doi:10.1063/1.1871344 · Cited by 967 · cited 1×
“Using the TMR effect, resistance changes up to 230% at room temperature have been reported [59], [60].”
BackgroundFiber Optic Sensors: An Introduction for Engineers and Scientists
(2011) · Wiley eBooks · doi:10.1002/9781118014103 · Cited by 783 · cited 1×
“Linear birefringent material behaves vice versa [61].”
Giant magnetic field dependent impedance of amorphous FeCoSiB wire
Beach, R. S., & Berkowitz, A. E. (1994) · Applied Physics Letters · doi:10.1063/1.111170 · Cited by 650
Primdahl, F. (1979) · Journal of Physics E: Scientific Instruments · doi:10.1088/0022-3735/12/4/001 · Cited by 499
Research works printed but not linked: 15
- ziegler, 2008, An isolated current to voltage voltage to voltage converter
- tipler, 2005, Understanding Hall effect devices
- tipler, 2005, An introduction to the Hall effect
- udd, 1991, Fiber Optic SensorsAn Introduction for Engineers and Scientists
- tipler, 1991, Physics for Scientists and Engineers
- ma, 2004, Isolated Current and Voltage Transducers
- baibich, 1997, The giant magnetoresistive head A giant leap for IBM research
- kowina, 2005, high dynamic magnetic beam current measurement by means of optimized magnet-resistance (mr) sensor engineering, Proc 7th Eur Workshop on Beam Diagnostics and Instrumentation for Particle Accelerators DIPAC 2005, 102
- beltran, 2005, AA and AB-series analog sensors datasheet
- mammano, 2005, High-side current-sense measurement
- spaziani, 1997, Using copper PCB etch for low value resistance
- spaziani, 2005, Cu-ETP copper specification
- ray, 2005, RCTrms Rogowski coil datasheet
- mammano, 1997, current sensing solutions for power supply designer, Power Design Seminar SEM 1200
- dezuari, 2003, Basic introduction to the use of magnetoresistive sensors
Cited by
Items 701–775 of 775
Towards traceable measurement of dynamic current
Klüss, J., Klasson, A., & Nieminen, T. (2024) · IEEE International Conference on High Voltage Engineering and Application (ICHVE) · doi:10.1109/ichve61955.2024.10676192
“Without a core, saturation is omitted, and the sensors are inherently linear [7].”
BackgroundInfluentialHawk: An Efficient NALM System for Accurate Low-Power Appliance Recognition
Wang, Z. M., Zhang, X., Wang, Y., Peng, X., & Xu, Z. (2024) · ACM Conference on Embedded Networked Sensor Systems (SenSys) · doi:10.1145/3666025.3699359
“Current sampling has three typical types of sensors[56]: shunt resistors, Hall effect sensors, and current transformers.”
BackgroundTotal Ionizing Dose Testing of a Current Sense Amplifier for Space Applications
Toro, D. G., Kuhm, H., Gunasekar, H., Eilenberger, M., & Aksteiner, N. (2024) · IEEE Radiation Effects Data Workshop (REDW) · doi:10.1109/redw61286.2024.10759185
“For this purpose, various sensors [1] are available on the market for applications such as motor control, battery management systems or many other applications requiring a monitoring of the current.”
A Composite Integration Method for Broadband Hybrid Current Sensing Technology
Zhou, Z., Jing-xin, L., YaFei, S., Hui, M., Xin, Z., & Haoze, L. (2024) · CPSS & IEEE International Symposium on Energy Storage and Conversion (ISESC) · doi:10.1109/isesc63657.2024.10785311
“Among these common current sensors, in Table I, the shunt has the problems of strong invasion, non-isolation, large loss, and difficult integration [7].”
Development of a proximity contactless ammeter based on GMR sensors for measuring direct currents
Neves, C. S., Barbosa, C. R. H., da Silva, E. C., Magalhães, D. P., & Gusmão, L. A. P. (2024) · Measurement Sensors · doi:10.1016/j.measen.2024.101444
“Another complication is that the insertion of the shunt changes the current to be measured [1,2].”
InfluentialLuo, R., Guo, J., Li, F., Zhou, Y., & Shi, Q. (2024) · Asian Conference on Frontiers of Power and Energy (ACFPE) · doi:10.1109/acfpe63443.2024.10800827
“Conversely, Rogowski coils excel in current measurement but are more susceptible to interference from external magnetic fields due to the absence of a core to focus the magnetic flux generated by the target current, potentially leading to measurement inaccuracies[5].”
Weak Current Sensor Based on Tunneling Magnetoresistive Effect for Complex Power Conditions
Shi, S., Liang, X., Guan, M., Ju, D., Zhang, M., Guo, J., Hu, Z., & Liu, M. (2025) · Lecture notes in electrical engineering · doi:10.1007/978-981-96-1387-8_46
Embedded Current-Sensorless Current Measurement Technique for Switched Mode Power Converters
Ray, O., & Biswas, K. (2025) · IEEE Instrumentation & Measurement Magazine · doi:10.1109/mim.2025.10946252
“Physical current sensors used for the measurement of inductor currents within power electronic converters exist in two different varieties: invasive and non-invasive types [6].”
High-Precision GaN-Based-SenseFET Design Based on a Lumped Parameter Electro-Thermal Network Model
Tang, X., Jiang, Q., Huang, S., Wang, X., & Liu, X. (2025) · IEEE Journal of the Electron Devices Society · doi:10.1109/jeds.2025.3563644
“In a highly efficient power system, the current flowing through the switching device, i.e., GaN power device, should be monitored in real-time for control or protection [2], [3], [4].”
Laboratory equipment usage rate management system based on current detection
Tian, R. (2025) · International Conference on Electronic Information Engineering and Data Processing (EIEDP) · doi:10.1117/12.3067349
“However, current laboratory equipment management still faces numerous issues [1].”
PV-fed Flyback-type Single-stage Single-phase Grid-tied System
Pardhi, P. K., & Sharma, S. K. (2024) · IEEE Power India International Conference · doi:10.1109/piicon63519.2024.10995174
“In the literature various sensing circuits are reported such as based on Hall-effect (electrical isolation), optical isolation, and non-isolation (using large resistive impedance) [18].”
Smart Sensor Technologies and Communication Interfaces for Environmental Monitoring at Schools
(2025) · International Journal of Science and Engineering Applications · doi:10.7753/ijsea1407.1003
A 90%-Random Fault Coverage Area-Efficient LED Driver Current Monitor
Colucci, A., Rigo, M., Carbonini, A., Fiocchi, C., Malcovati, P., & Bonizzoni, E. (2025) · IEEE International Symposium on Circuits and Systems proceedings · doi:10.1109/iscas56072.2025.11043250
“Additionally, temperature e ff ects and resistor tolerances must be accounted for to ensure consistent and reliable monitoring across varying operating conditions [4].”
Zhao, X., Jiang, L., Gao, G., & Lei, H. (2025) · IEEE Transactions on Instrumentation and Measurement · doi:10.1109/tim.2025.3587366
Oyane, A., Umetani, K., & Hiraki, E. (2025) · IEEE Access · doi:10.1109/access.2025.3587595
Lella, V., & Chandrasekaran, K. (2025) · International Conference on Power Electronics Converters for Transportation and Energy Applications (PECTEA) · doi:10.1109/pectea61788.2025.11076446
“The measurement principle for Rogowski coil (RC) [1], [2] is shown in Fig.”
A Hardware Measurement Platform for Quantum Current Sensors
Hoffmann, F., Bülter, A.-S., Horsthemke, L., Stiegekötter, D., Pogorzelski, J., Gregor, M., & Glösekötter, P. (2025) · doi:10.3390/engproc2025101011
An Improved Phase Current Reconstruction Algorithm Using Three-Resistor Sampling Technique
Jia, W., Cao, J., Xu, C., & Yu, P. (2025) · International Conference on Electronics, Integrated Circuits and Communication Technology (EICCT) · doi:10.1109/eicct65471.2025.11099754
“With their increasing adoption, market demands for drive control systems have also grown, requiring not only higher efficiency and precision but also reduced weight, compact size, and enhanced operational reliability[2].”
El‐Arwash, H. M., Alabid, M., El-Sehiemy, R. A., & Said, L. A. A. (2025) · Energy Science & Engineering · doi:10.1002/ese3.70251
“Researchers have tried to improve hardware by implementing quicker units for acquiring data [23 – 25], more precise and quick measurement sensors [26 – 28], higher power electronics switch switching frequencies [29 – 31], and optimized LC filter factors [32 – 36].”
Li, J.-L., & Huang, Y. (2025) · IEEE International Conference on Image Processing and Computer Applications (ICIPCA) · doi:10.1109/icipca65645.2025.11138490
“Currently, electromagnetic current transformers (CTs) in power systems face challenges such as insulation difficulties, susceptibility to magnetic saturation, and environmental concerns [1] .”
Investigation on the Susceptibility to RFI of High-Voltage Current Sensors
Fiori, F. L. (2025) · International Symposium on Electromagnetic Compatibility - EMC Europe (EMC Europe) · doi:10.1109/emceurope61644.2025.11176264
“Depending on the current magnitude, on the dynamic range and on the bandwidth needed to control the electric motor effectively or to react to failures, different solutions can be put in place [1], [2].”
Modeling and Suppression of Transient Voltage Interference in Magnetic Field-Based Current Sensors
Xu, C., Jiang, Z., Xin, M., Zhang, H., Luan, A., & Shao, S. (2025) · Annual Conference of the IEEE Industrial Electronics Society (IECON) · doi:10.1109/iecon58223.2025.11221086
“Among the diverse current sensing techniques, magnetic field-based sensors have garnered significant attention due to their non-invasive measurement, high bandwidth, and dc-current measurement capability [1].”
Development of a Current Measurement Device for Field Application
Siktár, B., Hegedűs, G., & Kakuk, J. (2025) · Journal of Physics Conference Series · doi:10.1088/1742-6596/3142/1/012017
“Overáll, the áuthors note thát emerging MR ánd fiber-optic techniques extend the performánce envelope but áre not yet universálly cost-competitive with tráditionál shunts [1].”
Pogorzelski, J., Glösekötter, P., Trinschek, S., Medina-Quero, J., Rojas, I., & Polo-Rodríguez, A. (2025) · International Journal of Electrical Power & Energy Systems · doi:10.1016/j.ijepes.2025.111371
An Open-Ended Flexible Printed Circuit Board Rogowski Coil with High Bandwidth
Tian, X., Bai, H. K., Wang, F., Swaim, J., Zimmermann, M., & Paver, H. (2025) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce58356.2025.11259918
“Current sensors are widely used for measuring currents in components and systems for control, protection, and testing [1], [2].”
Oiu, T., Zhang, Z., Das, A. K., & Zikpi, I. (2025) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce58356.2025.11259985
Ultra-Narrow Current Pulses Measurement Using a Cost-Effective Instrumentation System
Herranz, A. D. G., de Cabiedes, B. G., Pacheco, J. D. M., & López‐Vallejo, M. (2025) · Conference on Design of Circuits and Integrated Systems · doi:10.1109/dcis67520.2025.11281904
“Current consumption can be measured using direct or indirect methods [1].”
Closed-Form Theoretical Model for Magnetic Sensors to Measure Currents in Power Distribution Systems
Kulathuran, S. A., & Brahma, S. (2025) · IEEE Transactions on Instrumentation and Measurement · doi:10.1109/tim.2025.3619264
“E ff ective electrical isolation, along with size and cost considerations, drives the adoption of integrated circuit-based sensors that utilize the Hall e ff ect and magnetoresistive e ff ect [8], [21].”
On-State Resistance Measurement Circuit Under Galvanic Isolation Constraints
Shin, J., Shin, J.-W., Eo, S., Sung, D.-U., Jung, H.-W., & Moon, S. (2025) · IEEE International Future Energy Electronics Conference (IFEEC) · doi:10.1109/ifeec65025.2025.11301554
“Galvanic isolation for the current sensor is less challenging than for the voltage sensor, since standard isolated sensors such as current transformers, Rogowski coils, and Hall-effect sensors can be directly used [4].”
Lei, Y., Hu, J., Xu, Z., Zhou, W., & Han, J. (2026) · Science China Technological Sciences · doi:10.1007/s11431-025-3071-5
“Currently, several innovative algorithms and sensors [16– 19] have been developed to enhance the e ff ectiveness of aerial firefighting.”
A Novel 1-Shunt Current Sensing Scheme Using Current Ratio Function
Lee, D. (2026) · Journal of Electrical Engineering and Technology · doi:10.1007/s42835-025-02577-9
Fully-Differential Integrator based On-Chip Current Sensor for SiC MOSFET
Park, J., PARK, H., & Lim, J. (2025) · International SoC Design Conference · doi:10.1109/isocc66390.2025.11330113
“In [2], a Rogowski coil with high bandwidth is employed to accommodate the high switching frequency characteristics of SiC MOSFETs.”
Lu, J., Peng, P., Chen, J., Deng, S., Zou, S., Wang, Y., Zhao, Y., & Jin, Z. (2026) · IEEE Transactions on Applied Superconductivity · doi:10.1109/tasc.2026.3664063
Ding, X., Wang, J., Han, C., Chen, X., & Wang, J. (2026) · Designs · doi:10.3390/designs10010020
Cateley, R., Lapthorn, A., & Heffernan, B. (2025) · IEEE Annual Southern Power Electronics Conference · doi:10.1109/spec64875.2025.11379820
“However, the accuracy of the Rogowski coil measurement can be influenced by the coaxiality of the coil with respect to the conducting sample, external magnetic fields such as those produced by nearby high-current conductors [6], and the uniformity of the coil’s construction [7].”
CHENG, C.-Y. (2026) · JFPS International Journal of Fluid Power System · doi:10.5739/jfpsij.19.80
Roy, A. N., Biswas, K., & Ray, O. (2025) · IEEE Industrial Electronics Society Annual On-Line Conference (ONCON) · doi:10.1109/oncon68412.2025.11384602
“…is cumbersome as it may involve breakage of the circuit, involvement of additional power supplies and also an association of operational amplifier (OP-AMP) with the current sensor (resistive current sensor, hall effect sensor, etc) to generate the current feedback for the MPPT controller [9].”
Hou, L., & Peng, H. (2025) · IEEE International Power Electronics and Application Symposium (PEAS) · doi:10.1109/peas66638.2025.11403174
“For intrusive current sensors, sensitivity is a constant determined primarily by structural parameters [1]: Thus, the sensitivity of intrusive sensors is determined primarily by structural parameters and is unaffected by installation position.”
Hu, C., Yang, A., Zhu, L., & Li, M. (2025) · International Conference on Energy Technology and Electrical Power (ETEP) · doi:10.1109/etep67941.2025.11440627
Jankie, M., Hackl, T., Schitter, G., & Staufer, U. (2026) · Micro and Nano Engineering · doi:10.1016/j.mne.2026.100357
Capteur de courants innovant pour des systèmes polyphasés : application aux câbles multiconducteurs
Bourkeb, M. (2014) · doi:10.70675/35aa9c80zc832z405czb8b3z017360d7db7a
“Une analyse détaillée de plusieurs technologies non-intrusive est donnée dans [3-5].”
Zhou, K., Zhang, R., Zhang, S., Shen, Y., Hong, Z., & Xu, J. (2026) · IEEE Journal of Solid-State Circuits · doi:10.1109/jssc.2026.3677400
“A CCURATE current sensing is essential for functions such as solenoid control, battery charging, and overcurrent protection [1], [2], [3], [4].”
A Methodology for designing SiC and GaN device based converters for automotive applications
de Oliveira, J. S. (2021) · theses.fr (ABES) · doi:10.70675/a4bcac39zb228z4cb4zaf68z5e6291054611 · Cited by 3
Galvanically Isolated Coreless Peak Current Detector for Switch Mode Power Supplies
Niakan, H., Farahani, A., & Parkhideh, B. (2026) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2026.3679495 · Cited by 2
Castellani, F. (2023) · theses.fr (ABES) · doi:10.70675/4e2b79b3zfc43z4b8aza8bez05233e3f16ac · Cited by 1
Analysis of robustness of 650 V GaN HEMT under repetitive short-circuits
Lambert, A. (2025) · theses.fr (ABES) · doi:10.70675/dfbb85bcz1b8cz471fzbdabza09204e66390
Measurement and Correction of the Resistor Load Effect Under Low-Pressure Conditions
Yu, Y., Chen, S., Wang, K., Qian, L., Xu, S., & Fu, Y. (2026) · IEEE Transactions on Instrumentation and Measurement · doi:10.1109/tim.2026.3684657
“As an example, shunt resistors have been used extensively in current measurement due to their low cost, small size, and relatively simplicity, while providing reasonable accuracy [7], [8], [9], [10].”
Baraka, J., Elmir, M., & Amanquah, N. (2026) · International Conference on Artificial Intelligence, Computer, Data Sciences and Applications (ACDSA) · doi:10.1109/acdsa67686.2026.11467823
“…of power consumed by running software on separate microprocessors to quantify the power consumed by the software many ground breaking research such as in [6], [7] proposed different current measuring approaches such as the shunt resistor current measurement, ammeter and current mirror approaches.”
Dong, Y. Y., Yang, T., Li, X., Chen, M., Tian, Q., Cai, J., Luo, W., Li, B., Aristidou, P., & Bai, R. (2026) · Measurement Science and Technology · doi:10.1088/1361-6501/ae6e5b
“Hall-effect sensors offer non-contact measurement and low cost, but are prone to temperature variations and external magnetic interference, which can result in relatively lower accuracy [8, 9].”
Ma, H., Zhang, H., Liu, Y., Berkhout, M., & Fan, Q. (2026) · IEEE Journal of Solid-State Circuits · doi:10.1109/jssc.2026.3685735
“Several techniques have been developed for this current sensing, including shunt-resistor, sense-FET, and magnetic methods [9], [14].”
Cheng, F., Xia, J., Zhu, E., Zhang, L., Fang, Z., Sun, X., Wang, D., Li, S., Zhu, J., Li, Y., et al. (2026) · IEEE Journal of Solid-State Circuits · doi:10.1109/jssc.2026.3692476
“This is further degraded by parasitic inductance with non-negligible impedance at high frequencies [1].”
Residual current detector for AC and DC application
Milewski, S., Pirog, S., Chojowski, M., Baszyński, M., & DREWNIAK, M. (2026) · PRZEGLĄD ELEKTROTECHNICZNY · doi:10.15199/48.2026.05.3
Gradient Amplifier Design Techniques for MRI Systems: A Comparative Literature Review
Kızılbey, O., Karaböce, B., & Karademir, M. (2026) · Eng—Advances in Engineering · doi:10.3390/eng7060274
“…a closed-loop architecture; this system implements interstage current-parallel negative feedback (via U1A/U2A and resistor R6) to strictly enforce parity between the static input and feedback currents, thereby guaranteeing synchronous compensation and stable constant current operation [17,21,22].”
Optical current detection using the Faraday magneto-optic effect at the standard quantum noise limit
yang, P., Ke, X., Li, B., Tu, C., & Shi, Z. (2026) · Applied Optics · doi:10.1364/ao.597305
Budić, I., & Marković, T. (2026) · International Convention on Information and Communication Technology, Electronics and Microelectronics · doi:10.1109/mipro70003.2026.11591585
“The topology is based on a high-precision shunt resistor, one of the widely used methods for sensing current signals [1].”
A PCB-Embedded Differential Loop Probe for Non Invasive Transient Current Reconstruction
Chen, R. J., Gao, R. X., Wang, D. Q., & Wei, X. (2026) · doi:10.1109/apemc65388.2026.11593655
“Currently, high-frequency current detection techniques are primarily categorized into contact and non-contact methods [3].”
Kim, Y., Kim, B., Park, J., Han, K. J., Han, T., & Kim, D. (2026) · Materials Characterization · doi:10.1016/j.matchar.2026.116784
Design of Finger-Shaped CMOS Hall Sensor and Experimental Measurements
Fan, H., Yao, H., Yang, T., Maloberti, F., Wei, Q., & Feng, Q. (2026) · IEEE Transactions on Circuits and Systems I Regular Papers · doi:10.1109/tcsi.2026.3709612
“Compared with other magnetic sensors, such as anisotropic magnetoresistive (AMR) [1], [2], [3], tunnel magnetoresistive sensor (TMR) [4], [5], [6], and giant magnetoresistive (GMR) [7], [8], [9], Hall devices [10], [11] o ff er full compatibility with standard CMOS processes, enabling seamless…”
Diamond current sensor integrated with a magnetic flux concentrator
Ye, N., Zhen, K., Li, C., Li, C., Zheng, R., Xia, S., & Chen, B. (2026) · Applied Physics Letters · doi:10.1063/5.0342899
A ±50-A Shunt-Based Current Sensor With ±0.2% Gain Error From --40 °C to 125 °C
Park, S., Kim, H., Lee, J. S., Choi, S.-U., Kim, T.-H., Yim, J.-Y., Boo, J., Moon, U.-K., & Ahn, G. (2026) · IEEE Transactions on Circuits and Systems I Regular Papers · doi:10.1109/tcsi.2026.3716985
Wang, H., Zheng, L., Li, X., Xu, C., & Wang, W. (2026) · International Conference on Artificial Intelligence and Electromechanical Automation (AIEA) · doi:10.1109/aiea70743.2026.11632414
“Traditional shunts, current transformers, Rogowski coils and Hall sensors are limited in weak ferroresonance current monitoring [1], [2].”
High Accuracy Coulombic Efficiency (HACE) Determination for Battery Ageing AnalysisPreprint
Frankl, S. D., Rüther, T., Bauer, M., Hölzle, M., & Danzer, M. A. (2026) · SSRN Electronic Journal · doi:10.2139/ssrn.7346765
In-Situ Measurements in Reconfigurable Phased-Array Transmitters
Baylis, C., Swindell, J. E., Egbert, A., Goad, A. C., & Marks, R. J. (2026) · Electronics · doi:10.3390/electronics15173818
Güneş, H., Ege, B., Çıtak, H., Çoramık, M., Bıçakçı, S., & Ege, Y. (2026) · Journal of Electromagnetic Analysis and Application · doi:10.4236/jemaa.2026.187007
Liu, S., Huang, J., Feng, Z., Mao, Z., Xia, L., & Yu, C. (2026) · Journal of Lightwave Technology · doi:10.1109/jlt.2026.3729793
“…including shunt resistors, Hall sensors, magnetoresistive sensors, fluxgate probes, and fiber-optic current sensors, have been widely used, but they may suffer from insertion loss, temperature drift, magnetic saturation, limited miniaturization, or sensitivity to electromagnetic interference [1].”
Lyu, G., Ali, H., Peng, L., Tan, H., Yang, Y., & Ding, X. (2026) · IEEE Transactions on Instrumentation and Measurement · doi:10.1109/tim.2026.3726186
“Hall-e ff ect and TMR sensors provide isolated current measurement but are susceptible to temperature drift and external magnetic fields, and they add expense in high-power designs [21], [22], [23].”
InfluentialHoffmann, F., Bülter, A.-S., Homrighausen, J., Horsthemke, L., Peters, M., Gregor, M., Rojas, I., & Glösekötter, P. (2026) · doi:10.3390/engproc2026155006
Balaji, B., Kaliappan, B., Soundarrajan, A., P, H. S., Alexander Samuel, R., & Vidhya, H. (2026) · International Conference on Modern Sustainable Systems (CMSS) · doi:10.1109/cmss69636.2026.11689440
Current Sensing Method Based on MOSFET Junction Temperature Estimation for Low-Voltage Inverters
Kim, J., Ha, J., 이원식, Kim, H., Lim, H., & Lee, G.-H. (2026) · IEEE Access · doi:10.1109/access.2026.3743158
Model-driven low-latency hall sensor array for solid-state circuit breakers
Hu, Y., Hailong, H., Niu, C., 天波, 刘萌萌, Jiang, Y., Ouyang, T., & Wu, Y. (2026) · Sensors and Actuators A Physical · doi:10.1016/j.sna.2026.118678
Dou, H., Huo, Z., Li, Q., & Li, Z. (2026) · Energies · doi:10.3390/en19204946
Utilisation de la Magnéto-Impédance Géante pour la réalisation d'un capteur de courant
Zidi, M. (2014) · doi:10.70675/9be7063bzc0faz4508zbfe3z24e2c15a58bf
“En capteur de champ, le handicap de l’AMR réside dans la sensibilité aux phénomènes irréversibles [37], [38].”
Metadata
- Authors
- Ziegler, S., Woodward, R. C., Iu, H. H.-C., & Borle, L. J.
- Affiliations
- The University of Western Australia (AU)
- Venue
- IEEE Sensors Journal
- Published
- 2009-04
- Volume
- 9
- Issue
- 4
- Pages
- 354-376
- ISSN
- 1530-437X (ISSN-L)
- OpenAlex
- W2127394451
- Cited by
- 774
- References
- 63
- Citations by year
- 2026: 37 · 2025: 65 · 2024: 63 · 2023: 70 · 2022: 66 · 2021: 66 · 2020: 63 · 2019: 65 · 2018: 65 · 2017: 46 · 2016: 38 · 2015: 34 · 2014: 33 · 2013: 19 · 2012: 24
- FWCI
- 11.38
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- IEEE Sensors Journal (publishedVersion)
- UWA Profiles and Research Repository (UWA) (submittedVersion)
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Magnetic Field Sensors Techniques
- Physical Sciences › Physics and Astronomy › Instrumentation › Sensor Technology and Measurement Systems
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Analog and Mixed-Signal Circuit Design
- Keywords
- current sensing, current sensor, sensor principles, sensor characteristics, current measurement
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.