The DOI matches its Crossref record; 90 of the 90 references it cites were found in a registry or an index; 9 of the 90 sources its claims cite were checked for support.
A Review of Multilevel Inverter Topologies in Electric Vehicles: Current Status and Future Trends
Open accessAbstract
Traction inverter, as a critical component in electrified transportation, has been the subject of many research projects in terms of topologies, modulation, and control schemes. Recently, some of the well-known electric vehicle manufacturers have utilized higher-voltage batteries to benefit from lower current, higher power density, and faster charging times. With the ongoing trend toward higher DC-link voltage in electric vehicles, some multilevel structures have been investigated as a feasible and efficient option for replacing the two-level inverters. Higher efficiency, higher power density, better waveform quality, and inherent fault-tolerance are the foremost advantages of multilevel inverters which make them an attractive solution for this application. This paper presents an investigation of the advantages and disadvantages of higher DC-link voltage in traction inverters, as well as a review of the recent research on multilevel inverter topologies for electrified transportation applications. A comparison of multilevel inverters with their two-level counterpart is conducted in terms of efficiency, cost, power density, power quality, reliability, and fault tolerance. Additionally, a comprehensive comparison of different topologies of multilevel inverters is conducted based on the most important criteria in transportation electrification. Future trends and possible research areas are also discussed.
Overview
CoChat Summary
TL;DR
This review examines multilevel inverter topologies for electric vehicle traction drives as DC-link voltages rise toward 800 V and above, comparing them with conventional two-level inverters. It finds multilevel inverters can improve efficiency, power quality, and fault tolerance, but face cost, capacitor, control, and reliability trade-offs.
Key findings
- Moving from 400 V to 1.2 kV in a 150 kW system can reduce copper weight per meter by 63% by lowering current from 375 A to 125 A; Porsche reports a 30 kg reduction in electrical harness weight from doubling battery voltage.
- A Si MOSFET CHB multilevel inverter raised minimum low-speed efficiency from 70% for an IGBT-based two-level inverter to 92%; at higher speeds it remained 2%–3% better, and in urban driving cycles efficiency improved by approximately 10%. An MMC showed 3%–5% efficiency improvement in the constant torque region at 20 kHz maximum switching frequency.
- Cost comparisons show a two-level inverter at 6500.5 versus a 7-level CHB at 6433.3 when battery savings are included, and a two-level inverter at 1726 versus a three-level NPC at 1678, a 3% lower system cost due mainly to reduced filter cost.
- A three-level multilevel inverter can reduce output voltage THD by a factor of 2–3, and a 5-level NPC reduces maximum dv/dt and common-mode voltage by four times at constant switching speed; with one fault-tolerant capability, the reliability gap between two-, three-, and five-level inverters remains below 0.2 for 0–25,000 hours, and multiple fault-tolerant capabilities can make multilevel reliability surpass two-level.
Methods
- Review and comparative study of multilevel inverter topologies for electrified transportation, focusing on traction drives in electric vehicles, buses, trucks, trains, ships, and aircraft.
- Synthesizes literature and market data, including tables of commercial EV battery voltages, traction inverter structures, and comparisons of well-known and new multilevel topologies.
- Compares multilevel versus two-level inverters across efficiency, cost, power density, power quality, reliability, fault tolerance, and cooling, drawing on cited simulation and experimental studies rather than presenting new primary experiments.
Limitations
- The paper states that there are not many studies comparing different aspects of multilevel and two-level inverters specifically for traction applications, and that new multilevel topologies are not mature enough in control, modulation, voltage balancing, fault tolerance, and reliability and have not been implemented and tested for traction.
- The paper states that a comprehensive comparison of different numbers of levels, from 3 to 23, is still required in terms of efficiency, cost, power density, and reliability.
- Evident from the text: as a review, its quantitative comparisons depend on cited studies and their assumptions, and it does not provide a new experimental validation of its own.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
8 Valid · 12 Not valid · 66 Not checked · 67 Own results and interpretations
Every source the paper cites for this claim was checked and supports it.
In the paper
“Besides, employing higher-voltage batteries allows for a reduction in size and weight of the required cables for transferring a certain amount of power [6].”
What the sources say
- Supportedcites [6] [6] H. Tu, H. Feng, S. Srdic, and S. Lukic, 'Extreme fast charging of electric vehicles: A technology overview,' IEEE Trans. Transp. Electrific. , vol. 5, no. 4, pp. 861-878, Dec. 2019. - source
Section II states that high charging current requires larger-diameter cables and that transferring power at higher voltage is one way to reduce cable weight while delivering more power. This supports the claim that higher-voltage batteries can permit smaller, lighter charging cables for a given power transfer. (LLM, conf=0.94)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
Every source the paper cites for this claim was checked and supports it.
In the paper
“High current in a battery pack can impact pack hardware, busbars, fuses, disconnect switches, and tabs which results in increasing battery pack cost and weight [36].”
What the sources say
- Supportedcites [36] [36] S. Ahmed et al. , 'Enabling fast charging-a battery technology gap assessment,' J. Power Sour. , vol. 367, pp. 250-262, 2017. - source
Section 3.1, “Pack design” (p. 26), says higher current requires more robust pack hardware, including bus bars, tabs, fuses, and disconnect switches, resulting in increased pack weight and cost. This directly supports the attributed claim. (LLM, conf=0.95)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
Every source the paper cites for this claim was checked and supports it.
In the paper
“Electrolytic capacitors and supercapacitors can effectively reduce the battery RMS losses in this case [73].”
What the sources say
- Supportedcites [73] [73] A. Kersten, O. Theliander, E. A. Grunditz, T. Thiringer, and M. Bongiorno, 'Battery loss and stress mitigation in a cascaded h-bridge multilevel inverter for vehicle traction applications by filter capacitors,' IEEE Trans. Transp. Electrific. , vol. 5, no. 3, pp. 659-671, Sept. 2019. - source
The Drive Cycle Operation section (p. V-A) reports 'With configurations 4 and 8 a reduction of the battery losses by about 40 % is achieved' — configuration 4 being the large electrolytic capacitor and 8 the large supercapacitor — and the Conclusion states that placing the capacitors at the H-bridge inputs 'relieves the battery stress and reduces the battery losses to a great extent'. The Frequency Analysis (Table X) likewise shows both capacitor types cutting the battery current harmonics/RMS stress, with supercapacitors better at the low-speed operating point 1 and electrolytics better at high-frequency operating point 6. The citing phrase 'battery RMS losses' blends the paper's two quantities (drawn battery RMS current and ohmic battery losses), but both reductions are stated for both chemistries in the paper's cascaded H-bridge traction-inverter case, so the paraphrase is supported. (LLM, conf=0.85)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
Every source the paper cites for this claim was checked and supports it.
In the paper
“A comparison of reliability has been conducted in [80] between FC, NPC, and CHB structures. The large number of capacitors has resulted in the highest failure rate for FC structure, while CHB has the highest reliability between the three.”
What the sources say
- Supportedcites [80] [80] O. Alavi, A. Hooshmand Viki, and S. Shamlou, 'A comparative reliability study of three fundamental multilevel inverters using two different approaches,' Electronics , vol. 5, no. 2, 2016, Art. no. 18. - source
The Conclusions state that CHB is the best choice for reliability among the three inverters studied. Table 7 reports the highest mean time to failure for CHB (65,451 hours), compared with NPC (50,036) and FC (42,245), under the study's conditions. (LLM, conf=0.94)
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
Every source the paper cites for this claim was checked and supports it.
In the paper
“Generally, the input current of multilevel inverters can have lower current distortion compared to two-level structures [72].”
What the sources say
- Supportedcites [72] [72] R. A. Rana et al. , 'Review of multilevel voltage source inverter topologies and analysis of harmonics distortions in FC-MLI, ' Electron. , vol. 8, no. 11, 2019, Art. no. 1329. - source
Section 2, “Topologies of Multilevel Inverter,” introduces advantages of multilevel inverters over two-level inverters and lists small input current distortion among them. This supports the citing sentence’s qualified comparison. (LLM, conf=0.88)
plainstates a possible cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
62 more claims · 2 with their cited sources checked
Create a free account to see all 153 claims and to verify the 9 references still open.
- Probably not a substantial claim. 55
- It may state two separate claims as one. 54
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
“| Sum | 1726 | 1678 |”
Reported 1726 · recomputed 1826
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
“| Sum | 1726 | 1678 |”
Reported 1678 · recomputed 1928
Citations
Cites
Recent Advances and Industrial Applications of Multilevel Converters
Kouro, S., Malinowski, M., Gopakumar, K., Pou, J., Franquelo, L. G., Wu, B., Rodriguez, J., Pérez, M. A., & Leon, J. I. (2010) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2010.2049719 · Cited by 3,872 · cited 1×
“propulsion system due to high efficiency and low size, suffer from poor input current quality which will disturb the onboard ship power system [60].”
BackgroundLithium-ion battery fast charging: A review
Tomaszewska, A., Chu, Z., Feng, X., O'Kane, S., Liu, X., Chen, J., Ji, C., Endler, E., Li, R., Liu, L., et al. (2019) · eTransportation · doi:10.1016/j.etran.2019.100011 · Cited by 1,592 · cited 1×
“the biggest challenges which are impeding the fast growth of transportation electrification [3].”
BackgroundHigh‐Power Converters and AC Drives
Wu, B., & Narimani, M. (2017) · doi:10.1002/9781119156079 · Cited by 1,571
Self-citationSchweizer, M., & Kolar, J. W. (2013) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2012.2203151 · Cited by 1,006
Extreme Fast Charging of Electric Vehicles: A Technology Overview
Tu, H., Feng, H., Srdic, S., & Lukic, S. (2019) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2019.2958709 · Cited by 898 · cited 1×
“Besides, employing higher-voltage batteries allows for a reduction in size and weight of the required cables for transferring a certain amount of power [6].”
BackgroundElectrical Motor Drivelines in Commercial All-Electric Vehicles: A Review
de Santiago, J., Bernhoff, H., Ekergård, B., Eriksson, S., Ferhatovic, S., Waters, R., & Leijon, M. (2012) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2011.2177873 · Cited by 669
Teichmann, R., & Bernet, S. (2005) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2005.847285 · Cited by 578 · cited 4×
“Another comparison has been made in [97] between a conventional two-level inverter with a three-level NPC inverter.”
BackgroundInfluentialBabaei, E., Laali, S., & Bayat, Z. (2015) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2014.2336601 · Cited by 523
Vidal, C., Malysz, P., Kollmeyer, P., & Emadi, A. (2020) · IEEE Access · doi:10.1109/access.2020.2980961 · Cited by 512
Self-citationHybrid Multilevel Inverter Using Switched Capacitor Units
Babaei, E., & Gowgani, S. S. (2014) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2013.2290769 · Cited by 498
Research works printed but not linked: 4
- wand, 2016, High performance 800v e-motor for automotive application, AVL Trimerics GmbH
- reber, 2016, New possibilities with 800-volt charging, Porsche Eng Mag, 1, 10
- urban, 0, Functional safety-relevant wireless communication in automotive battery management systems, Texas Instruments
- vogt, 2020, Wired vs. wireless communications in EV battery management, Texas Instruments
Cited by
Ali, A., H. H. Mousa, H., F. Shaaban, M., A. Azzouz, M., & S. A. Awad, A. (2024) · Journal of Modern Power Systems and Clean Energy · doi:10.35833/mpce.2023.000107 · Cited by 162
“Several review research works have investigated the most prominent challenges and the future research trends for PECs utilized in EV applications in [2], [3], [4] - [7], [8], [12], [13], [15], [23]-[25], [29], [31], [33], [38]-[41], [48], [72], [73], [80], [97], [98].”
Choudhury, S., Bajaj, M., Dash, T., Kamel, S. M., & Jurado, F. (2021) · Energies · doi:10.3390/en14185773 · Cited by 179
Carne, G. D., Maroufi, S. M., Beiranvand, H., Angelis, V. D., D’Arco, S., Gevorgian, V., Waczowicz, S., Mather, B. A., Liserre, M., & Hagenmeyer, V. (2024) · Electric Power Systems Research · doi:10.1016/j.epsr.2024.110963 · Cited by 183
On-Board Chargers for High-Voltage Electric Vehicle Powertrains: Future Trends and Challenges
Pradhan, R., Keshmiri, N., & Emadi, A. (2023) · IEEE Open Journal of Power Electronics · doi:10.1109/ojpel.2023.3251992 · Cited by 142
“as lower voltage total harmonic distortion (THD), electromagnetic interference (EMI), and higher efficiency at higher voltages [60], [61].”
BackgroundSelf-citationZhang, Q., Yan, J., Gao, H. O., & You, F. (2023) · Advances in Applied Energy · doi:10.1016/j.adapen.2023.100147 · Cited by 118
Metadata
- Authors
- Poorfakhraei, A., Narimani, M., & Emadi, A.
- Affiliations
- McMaster University (CA)
- Venue
- IEEE Open Journal of Power Electronics
- Published
- 2021
- Volume
- 2
- Pages
- 155-170
- ISSN
- 2644-1314 (ISSN-L)
- OpenAlex
- W3134222763
- Cited by
- 424
- References
- 84
- Citations by year
- 2026: 54 · 2025: 102 · 2024: 104 · 2023: 93 · 2022: 53 · 2021: 18
- FWCI
- 19.67
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Locations
- IEEE Open Journal of Power Electronics (publishedVersion, cc-by)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Multilevel Inverters and Converters
- Physical Sciences › Engineering › Automotive Engineering › Electric and Hybrid Vehicle Technologies
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Electric Motor Design and Analysis
- Keywords
- multilevel inverter, electric vehicle traction inverter, inverter topology, DC bus voltage, two-level inverter, power density, fault tolerance, power quality, inverter efficiency, electric mobility
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol and qwen3.8-omni-flash).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: A Review of Multilevel Inverter Topologies in Electric Vehicles: Current Status and Future Trends. https://app.cochat.ai/papers/10.1109/ojpel.2021.3063550
- The paper
- Poorfakhraei, A., Narimani, M., & Emadi, A. (2021). A Review of Multilevel Inverter Topologies in Electric Vehicles: Current Status and Future Trends. IEEE Open Journal of Power Electronics. https://doi.org/10.1109/ojpel.2021.3063550
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.