Review and Outlook on GaN and SiC Power Devices: Industrial State-of-the-Art, Applications, and Perspectives
Open accessThe DOI matches its Crossref record; 55 of the 55 references it cites were found in a registry or an index; 9 of the 77 sources its claims cite were checked for support.
Abstract
We present a comprehensive review and outlook of silicon carbide (SiC) and gallium nitride (GaN) transistors available on the market for current and next-generation power electronics. Material properties and structural differences among GaN and SiC devices are first discussed. Based on the analysis of different commercially available GaN and SiC power transistors, we describe the state-of-the-art of these technologies, highlighting the preferential power conversion topologies and the key characteristics of each technological platform. Current and future fields of application for GaN and SiC devices are also reviewed. The article also reports on the main reliability aspects related to both technologies. For GaN HEMTs, threshold voltage stability, dynamic ON-resistance, and breakdown limitation are described, whereas for SiC MOSFETs the analysis also focuses on gate oxide failure and short-circuit (SC) robustness. Finally, we give an overview on the perspective of such materials in different fields of interest. An indication of possible future improvements and developments for both technologies is drawn. The requirements for hybrid converters, along with a careful optimization of performance and the use of innovative optimization tools, are underlined.
Overview
CoChat Summary
TL;DR
This review compares commercially available SiC and GaN power transistors, their material properties, applications, and reliability. It finds GaN e-mode HEMTs lead in key switching/conduction figures of merit, while SiC is more mature for high-voltage/high-power and harsh-condition applications, with both technologies expected to coexist.
Key findings
- In the 650 V comparison, GaN e-mode HEMTs show the lowest \(R_{\mathrm{ON}} \times Q_G\) FOM (about 265–372 mΩ·nC in Table II) versus SiC (about 1580–3480 mΩ·nC) and Si (3120 mΩ·nC); GaN e-mode input capacitance is in the 200 pF range, while SiC is above 900 pF and Si is above thousands of pF. GaN e-mode HEMTs also have zero reverse recovery charge, versus about 100 nC for SiC and GaN cascode HEMTs and thousands of nC for Si MOSFETs.
- SiC covers 650, 900, 1000, 1200, and 1700 V classes, while GaN covers 15–1200 V but is mostly limited to 650 V, with only one 900 V and one 1200 V solution; above 900 V, SiC remains the preferential choice.
- Current applications: SiC is widely used in hybrid/electric vehicle traction inverters (Tesla since 2017), while GaN is common in smartphone/PC power supplies and chargers, enabling chargers with three times lower volume than conventional Si ac–dc converters. Future expectations: below 400 V GaN may dominate; 400–1200 V SiC and GaN may coexist; above 1200 V SiC is expected for train traction, wind turbines, and smart grids.
- Reliability: SiC MOSFETs show lower \(V_{\mathrm{th}}\) shift and no dynamic ON-resistance effects; reported gate oxide \(t_{63\%}\) was \(>10^6\) s at 150 °C in 2020 and \(>10^8\) s at 150 °C in 2021 for all vendors tested. GaN challenges include threshold-voltage instability, dynamic ON-resistance increase, and breakdown limitations, with \(>1000\) V reliability still under optimization.
Methods
- Review and outlook paper: compares material properties and structural differences among commercial SiC and GaN power transistor topologies.
- Datasheet-based comparison of selected commercial 600/650 V SiC, GaN, and Si transistors with maximum drain current in the 30–50 A range and typical ON-resistance around 50 mΩ, plus selected 900 V and 1200 V devices; radar plots compare \(R_{\mathrm{ON}} \times Q_G\), input capacitance, reverse recovery charge, and switching times.
- Literature synthesis on applications, circuit topologies, and reliability mechanisms including bias temperature instability, dynamic ON-resistance, breakdown, gate oxide failure, and short-circuit robustness.
Limitations
- Stated: Table II is not an exhaustive list of commercially available transistors; higher-voltage GaN performance and reliability are still under optimization; drain-induced \(V_{\mathrm{th}}\) shift is not widely studied or well understood; GaN short-circuit and surge capabilities are still under study due to its relatively early development phase.
- Evident: the review relies on datasheets and published literature rather than new experimental measurements, and its device comparisons are limited to selected parts and voltage/current classes, so they may not represent the full market.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures



![Fig. 4 Frequency and power regimes for different power device technologies. Note that SiC and GaN devices work at substantially higher frequencies and powers with respect to Si-based devices. Data based on [14].](https://figures.cochat.ai/paper-figures/8bfb1bf8ff2f4ce3a6add454ccdf891a/review-and-outlook-on-gan-and-sic-power-devices-industrial-state-of-the-art-figure-4.png)


![Fig. 7 (a) Positive and (b) negative threshold voltage shift induced by different mechanisms of electron and hole trapping in a p-GaN gate HEMT gate-stack. The curves are obtained after referring to the initial threshold voltage value at t = 10 µ s. Reprinted with permission from A. Stockman et al., © 2021 IEEE [22].](https://figures.cochat.ai/paper-figures/cd2d8843c7b84ea5a60ba314cdc92f43/review-and-outlook-on-gan-and-sic-power-devices-industrial-state-of-the-art-figure-7.png)
![Fig. 8 Trapping mechanisms in the gate-stack of SiC (a) and GaN (b) power transistors, leading to V th Shift. Note the different confinement of carriers in the channel. In SIC MOSFETs, the main mechanisms involved are: electron trapping at interface and border traps between SiC and SiO2 (1a), hole trapping in the oxide (3a) [holes are generated through impact ionization events (2a)]. In e-mode HEMTs, the main mechanisms are: electron trapping at the AlGaN/GaN interface and in AlGaN traps (2b), hole accumulation at the p-GaN/AlGaN interface (5b) and consequent hole trapping in the AlGaN (6b), electrons and holes overcoming the AlGaN barrier (1b and 4b respectively), hole trapping in the buffer (7a) and at the interface between buffer and the strain relief layers (8a).](https://figures.cochat.ai/paper-figures/14c13fe19592486fb7f32b220e648a58/review-and-outlook-on-gan-and-sic-power-devices-industrial-state-of-the-art-figure-8.png)
![Fig. 9 Non-monotonic threshold voltage shift visible in 4H-SiC n-MOSFETs during a positive bias stress at room temperature. Reprinted from F. Masin et al., with the permission of AIP Publishing [30].](https://figures.cochat.ai/paper-figures/1ee311a5210645179651cd1c4ed261fa/review-and-outlook-on-gan-and-sic-power-devices-industrial-state-of-the-art-figure-9.png)
![Fig. 10 Comparison between short-circuit waveforms of devices with and without a MOSFET connected as source resistance. A reduced current peak and average value can be observed in CM1 and CM2 waveforms. Reprinted with permission from A. Kanale and B. J. Baliga, © 2019 IEEE [57].](https://figures.cochat.ai/paper-figures/7dc82243d8ea479cabdbf39731ecaab6/review-and-outlook-on-gan-and-sic-power-devices-industrial-state-of-the-art-figure-10.png)
Verification
Claims the paper makes
8 Valid · 6 Not valid · 53 Not checked · 98 Own results and interpretations
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“The first commercially available GaN power FET was introduced in the market Zhong et al. [7], ten years later with respect to the first commercial SiC device.”
What the sources say
- Partly supportedcites [7] sourceExperimental — accuracy not yet measured
The Introduction states that the first commercial enhancement-mode GaN-on-Si device was released in 2010. It does not give a date for the first commercial SiC device or establish the claimed ten-year gap. (LLM, conf=0.88)
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Other reports [29], [30], [31] show the presence of two phases in the dynamics of the shift, as shown in Fig. 9, which can be ascribed to the competition of two distinct trapping processes.”
What the sources say
- Partly supportedcites [29] sourceExperimental — accuracy not yet measured
Section D reports threshold-voltage shifts associated with electron and hole trapping: hole trapping dominates at 10 MV/cm, while electron trapping dominates at 8 MV/cm. It does not report two successive phases in the time dynamics of a threshold-voltage shift caused by competition between those processes; it compares behavior under different oxide fields. Page numbers are not available in our copy. (LLM, conf=0.85)
- Supportedcites [30] source
The Abstract of 10.1063/5.0057285 explicitly identifies 'two processes responsible for the nonmonotonic threshold voltage variation': negative-charge (electron) trapping giving a positive ΔVTH at ξOX < 8 MV/cm and positive-charge (hole) trapping giving a negative shift at higher field, with logarithmic and exponential kinetics respectively. The Fig. 2 caption likewise states 'Two main behaviors can be noticed', and the modelling section (III.A / discussion of Fig. 3) says the two contributions must be summed, with VTH 'keeping rising due to continuous electron trapping' at the end of the hole transient — i.e. the shift dynamics arise from the interplay of two distinct trapping processes. This matches the cited sentence's attribution (two phases in the shift dynamics ascribed to competition of two trapping processes) for 4H-SiC MOSFETs. (LLM, conf=0.88)
- Not checked — no full text of the sourcecites [31] source
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
Every source the paper cites for this claim was checked and supports it.
In the paper
“This is achieved by properly cascading ac-dc, dc-dc, and dc-ac converters, using for example resonant LLC conversion topologies for the dc-dc part, like the 2 MW one described in [20].”
What the sources say
- Supportedcites [20] source
The Introduction describes an AC-to-DC front end, insulated DC/DC converters, and three-phase inverters supplying the traction motors. The Structures section calls its resonant single-active-bridge DC/DC converter a resonant LLC converter, and the Conclusions identify the assessed PETT as a 2 MW system. Page numbers are unavailable in our copy. (LLM, conf=0.91)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Since lifetime scales with temperature and voltage, shortening of test times can be effectively achieved by increasing test temperature and voltage, then extrapolating data at the target operating condition of the device [29].”
What the sources say
- Partly supportedcites [29] sourceExperimental — accuracy not yet measured
In “Implications on Measurement Times” (page not supplied), the paper says higher temperatures can shorten tests at lower oxide fields and permit extrapolation, but says this approach does not work for the packaged devices studied because of their temperature ratings. In “Implications for Lifetime Predictions” (page not supplied), it warns that extrapolation from high oxide fields significantly overestimates lifetime; reliable predictions require measurements below 8.5 MV/cm. Thus the claim omits important limits on increasing temperature and voltage. (LLM, conf=0.88)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
In the paper
“Moreover, GaN devices enable the possibility for a diode-free H-Bridge configuration, having reverse conduction capabilities [16].”
What the sources say
- Not matchedcites [16] Dhayagude, 2021
Couldn’t be matched to a paper in Crossref, so it can’t be checked.
hedgedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Not matched
58 more claims
Create a free account to see all 165 claims and to verify the 9 references still open.
- It may state two separate claims as one. 73
- Probably not a substantial claim. 43
- The quote only partly states this claim. 1
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“SiC and GaN can operate under high-voltage and high-temperature conditions thanks to their Wide-Bandgaps (2.9-3.4 eV) and critical electric field strengths (2.2-4 MV cm -1 ), outperforming conventional Si in these regimes [2-5].”
From Thermal Management of Wide-Bandgap Power Semiconductors: Strategies and Challenges in SiC and GaN Power Devices (2025) · cites this paper as [5]
Experimental — accuracy not yet measured
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ C. SiC and GaN Transistors in the 600/650 V Range · p. 3
“in SiC transistors (above 900 pF)”
§ TABLE II · p. 4
“| SiC | Rohm (SCT3060ALHR) | Trench MOSFET | 650 | 60 | 39 | 58 | 3480 | 852 |”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ III. APPLICATIONS · p. 5
“owing to the higher breakdown field ( > 3 mV/cm)”
§ TABLE I · p. 2
“| Material | EG (eV) | Ecrit (MV/cm) | μe (cm2/Vs) | Vs (·107 cm/s) | Kth (W/cmK) | |------------|-----------|-----------------|---------------|------------------|---------------| | Si | 1.12 | 0.3 | 1440 | 1 | 1.3 | | 4H-SiC | 3.23 | 2.5 | 950 | 2 | 3.7 |”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ C. SiC and GaN Transistors in the 600/650 V Range · p. 3
“from R ON × Q G > 1500 m · nC of SiC and Si devices to R ON × Q G > 300 m · nC”
§ TABLE II · p. 4
“| GaN | STMicro (SGT65R65AL) | e-mode | 650 | 49 | 25 | 5.4 | 264.6 | 286 |”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ C. SiC and GaN Transistors in the 600/650 V Range · p. 3
“The selection is based on the continuous drain maximum current capabilities (between 30 and 50 A)”
§ TABLE II · p. 4
“| GaN | Infineon (IGLD60R070D1) | e-mode | 600 | 55 | 15 | 5.8 | 319 |”
Citations
Cites
Review of Silicon Carbide Power Devices and Their Applications
She, X., Huang, A. Q., Lucia, O., & Ozpineci, B. (2017) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2017.2652401 · Cited by 1,773 · cited 1×
“Ten years after the beginning of the studies on such material in the power electronics field, i.e., around 1990, it was possible to commercialize the first SiC Schottky diode [4].”
BackgroundUltrawide‐Bandgap Semiconductors: Research Opportunities and Challenges
Tsao, J. Y., Chowdhury, S., Hollis, M. A., Jena, D., Johnson, N. M., Jones, K. A., Kaplar, R. J., Rajan, S., Van de Walle, C. G., Bellotti, E., et al. (2018) · Advanced Electronic Materials · doi:10.1002/aelm.201600501 · Cited by 1,602 · cited 1×
“Nevertheless, these materials are of major interest for specific applications [3], and working devices have already been demonstrated.”
BackgroundUemoto, Y., Hikita, M., Ueno, H., Matsuo, H., Ishida, H., Yanagihara, M., Ueda, T., Tanaka, T., & Ueda, D. (2007) · IEEE Transactions on Electron Devices · doi:10.1109/ted.2007.908601 · Cited by 1,038 · cited 1×
“To achieve normally-OFF operation, two effective techniques are nowadays widely adopted: 1) the use of a p-GaN gate-stack [8], as shown in Fig.”
MethodHigh electron mobility transistor based on a GaN-Al x Ga1−x N heterojunction
Asif Khan, M., Bhattarai, A., Kuznia, J. N., & Olson, D. T. (1993) · Applied Physics Letters · doi:10.1063/1.109775 · Cited by 911
GaN-based power devices: Physics, reliability, and perspectives
Meneghini, M., De Santi, C., Abid, I., Buffolo, M., Cioni, M., Khadar, R. A., Nela, L., Zagni, N., Chini, A., Medjdoub, F., et al. (2021) · Journal of Applied Physics · doi:10.1063/5.0061354 · Cited by 723 · cited 2×
“…through the adoption of SiC and GaN devices favor the development of highly efficient dc–ac and dc–dc converters, allowing to reduce the weight and volume of the electronic components, which is of great interest for battery-operated applications such as EVs, and to increase power density [10].”
BackgroundSelf-citationLelis, A. J., Green, R., Habersat, D. B., & El, M. (2015) · IEEE Transactions on Electron Devices · doi:10.1109/ted.2014.2356172 · Cited by 477
Stability, Reliability, and Robustness of GaN Power Devices: A Review
Kozak, J. P., Zhang, R., Porter, M., Song, Q., Liu, J., Wang, B., Wang, R., Saito, W., & Zhang, Y. (2023) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2023.3266365 · Cited by 441
Influences of Device and Circuit Mismatches on Paralleling Silicon Carbide MOSFETs
Li, H., Munk-Nielsen, S., Wang, X., Maheshwari, R., Beczkowski, S., Uhrenfeldt, C., & Franke, W.-T. (2016) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2015.2408054 · Cited by 306 · cited 1×
“Higher current overshoots can therefore occur, and a derating of current capability may be needed to remain within SOA limits, thus yielding to an unoptimized usage of the solid-state switches [62].”
BackgroundTime dependent dielectric breakdown physics – Models revisited
McPherson, J. W. (2012) · Microelectronics Reliability · doi:10.1016/j.microrel.2012.06.007 · Cited by 268 · cited 2×
“In the first case, the gate corresponds effectively to the one of a Si MOSFET, which can suffer from the well-known time-dependent-dielectric-breakdown (TDDB) [37].”
BackgroundMethodA review on the GaN-on-Si power electronic devices
Zhong, Y., Zhang, J., Wu, S., Jia, L., Yang, X., Liu, Y., Zhang, Y., & Sun, Q. (2022) · Fundamental Research · doi:10.1016/j.fmre.2021.11.028 · Cited by 216
Research works printed but not linked: 7
- 2023, Stephen Colino
- Ramanan, 2023, Automotive GaN FETs Engineered for High Frequency and Robustness in HEV/EVs
- Dhayagude, 2021, Topologies for High Voltage GaN Applications in the 45W to 10 kW Power Levels
- Taranovich, 2016, Google Little Box Challenge Showcases GaN Power Element
- Dodge, 2018, SiC in Solar Inverter Topologies
- Burkart, Advanced modeling and multi-objective optimization/evaluation of SiC converter systems, 2
- 2023, JESD312 Automotive Solid State Drive (SSD) Device Standards
Cited by
Wide-bandgap semiconductors and power electronics as pathways to carbon neutrality
Zhang, Y., Dong, D., Li, Q., Zhang, R., Udrea, F., & Wang, H. (2025) · Nature Reviews Electrical Engineering · doi:10.1038/s44287-024-00135-5 · Cited by 141
“Owing to their superior FOMs, WBG devices enable operations in frequency and power regimes that are beyond the capabilities of Si devices 37 (Fig.”
ISAC—A Survey on Its Layered Architecture, Technologies, Standardizations, Prototypes, and Testbeds
Luo, X., Lin, Q., Zhang, R., Chen, H., Wang, X., & Huang, M. (2025) · IEEE Communications Surveys & Tutorials · doi:10.1109/comst.2025.3565534 · Cited by 135
“They also exhibit exceptional thermal conductivity/stability, and chemical stability, the qualities that have made these materials critically important in diverse application domains, including electric vehicles, smart grids, 5G BS, radar systems, and satellite communications [202].”
High-Power Electronic Applications Enabled by Medium Voltage Silicon-Carbide Technology: An Overview
Nielsen, M. R., Deng, S., Mirza, A. B., Kjærsgaard, B. F., Jørgensen, A. B., Zhao, H., Li, Y., Munk‐Nielsen, S., & Luo, F. (2024) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2024.3442483 · Cited by 92
“Several overview papers have already been published in the literature related to the applicability of the SiC technology [103], [202], [203], [204]; however, these overview papers mainly focus on LV applications.”
Kazmi, J., Abbas, A., Young, D. J., Shah, J. H., Ahmad, W., Shah, S. S. A., Raza, S. R. A., Mohamed, M. A., Govorov, A. O., & Wang, Z. M. (2024) · Materials Today · doi:10.1016/j.mattod.2024.11.004 · Cited by 82
Corti, F., Iacono, S. D., Astolfi, D., Pasetti, M., Vasile, A., Reatti, A., & Flammini, A. (2024) · Energy Reports · doi:10.1016/j.egyr.2024.06.026 · Cited by 69
Metadata
- Authors
- Buffolo, M., Favero, D., Marcuzzi, A., De Santi, C., Meneghesso, G., Zanoni, E., & Meneghini, M.
- Affiliations
- University of Padua (IT)
- Department of Information Engineering, University of Padova, Padua, Italy
- Venue
- IEEE Transactions on Electron Devices
- Published
- 2024-03
- Volume
- 71
- Issue
- 3
- Pages
- 1344-1355
- ISSN
- 0018-9383 (ISSN-L)
- 1557-9646
- OpenAlex
- W4390691388
- Cited by
- 476
- References
- 55
- Citations by year
- 2026: 211 · 2025: 214 · 2024: 50
- FWCI
- 48.96
- Type
- journal article
- Language
- en
- Open access
- hybrid
- doi.org
- Licence
- Locations
- IEEE Transactions on Electron Devices (publishedVersion, other-oa)
- Padua Research Archive (University of Padova) (submittedVersion, cc-by-nc-nd)
- Funders
- MOST–Sustainable Mobility Center through the European Union Next-GenerationEU (PIANO NAZIONALE DI RIPRESA E RESILIENZA (CN00000023)
- Vertical GaN on Silicon: Wide bandgap Power at Silicon Cost (YESvGaN) Project
- Electronic Component Systems for European Leadership Joint Undertaking (101007229)
- JU from the European Union’s Horizon 2020 Research and Innovation Programme and Germany, France, Belgium, Austria, Sweden, Spain, Italy
- GaN4AP Project-GaN for Advanced Power Applications
- ECSEL JU (101007310)
- JU from the European Union’s Horizon 2020 Research and Innovation Programme, and Italy, Germany, France, Poland, Czech Republic, The Netherlands
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Silicon Carbide Semiconductor Technologies
- Physical Sciences › Physics and Astronomy › Condensed Matter Physics › GaN-based semiconductor devices and materials
- Physical Sciences › Materials Science › Electronic, Optical and Magnetic Materials › Ga2O3 and related materials
- Keywords
- gallium nitride, silicon carbide, power transistors, power electronics, GaN HEMT, SiC MOSFET, converter topology, device reliability, threshold voltage stability, on-resistance, breakdown voltage, short-circuit robustness, hybrid converter
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol and qwen3.8-omni-flash).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Review and Outlook on GaN and SiC Power Devices: Industrial State-of-the-Art, Applications, and Perspectives. https://app.cochat.ai/papers/10.1109/ted.2023.3346369
- The paper
- Buffolo, M., Favero, D., Marcuzzi, A., De Santi, C., Meneghesso, G., Zanoni, E., & Meneghini, M. (2024). Review and Outlook on GaN and SiC Power Devices: Industrial State-of-the-Art, Applications, and Perspectives. IEEE Transactions on Electron Devices. https://doi.org/10.1109/ted.2023.3346369
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.