Fault-Tolerant Voltage Source Inverter for Permanent Magnet Drives
The DOI matches its Crossref record; 18 of the 19 references it cites were found in a registry or an index.
Abstract
In this paper, a two-level fault-tolerant voltage source inverter (VSI) for permanent magnet drives is systematically designed and tested. A standard two-level inverter consists of three legs. In this case of fault-tolerant inverter, a redundant leg is added that replaces the faulted leg. Faulted leg isolation and redundant leg insertion are done by using independent back-to-back-connected thyristors. The proposed inverter provides tolerance to both short-circuit and open-circuit faults of the switching devices. The postfault performance is the same as the normal prefault operation and fault compensation is fast enough such that there is negligible disturbance in the drive operation. The fault tolerance of the inverter is verified using field-oriented control of a permanent magnet synchronous motor.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“According to [238], [239], power semiconductor device damages account for approximately 35% of all ASD faults.”
From Fault Diagnosis and Fault-Tolerant Control of PMSM Drives–State of the Art and Future Challenges (2022) · cites this paper as [239]
In the citing paper
“Recently, phase redundancy approaches [239], [309] have gained popularity due to their full fault recovery without oversizing the drive.”
From Fault Diagnosis and Fault-Tolerant Control of PMSM Drives–State of the Art and Future Challenges (2022) · cites this paper as [239]
Citations
Cites
Welchko, B. A., Lipo, T. A., Jahns, T. M., & Schulz, S. E. (2004) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2004.830074 · Cited by 724 · cited 1×
“Several fault-tolerant topologies are available in the literature [5]; some of them reconfigure the standard inverter topology and reformulate the current references so that the rotating”
BackgroundFault detection of open-switch damage in voltage-fed PWM motor drive systems
de Araujo Ribeiro, R. L., Jacobina, C. B., da Silva, E. R. C., & Lima, A. M. N. (2003) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2003.809351 · Cited by 441 · cited 2×
“According to [14], the open-circuit fault of the IGBT can be detected by inserting voltage sensors at desired locations.”
BackgroundMethodInvestigation of fault modes of voltage-fed inverter system for induction motor drive
Kastha, D., & Bose, B. K. (1994) · IEEE Transactions on Industry Applications · doi:10.1109/28.297920 · Cited by 386
Fault detection and isolation on a PWM inverter by knowledge-based model
Peuget, R., Courtine, S., & Rognon, J.-P. (1998) · IEEE Transactions on Industry Applications · doi:10.1109/28.739017 · Cited by 384
Experimental fault-tolerant control of a PMSM drive
Bolognani, S., Zordan, M., & Zigliotto, M. (2000) · IEEE Transactions on Industrial Electronics · doi:10.1109/41.873223 · Cited by 382
A strategy for improving reliability of field-oriented controlled induction motor drives
Liu, T.-H., Fu, J.-R., & Lipo, T. A. (1993) · IEEE Transactions on Industry Applications · doi:10.1109/28.245714 · Cited by 374 · cited 1×
“faulted leg has to be connected to the midpoint of the dc voltage link, created using the use of two capacitors [6].”
MethodInvestigation of fault modes of voltage-fed inverter system for induction motor drive
Kastha, D., & Bose, B. K. (2003) · Conference Record of the 1992 IEEE Industry Applications Society Annual Meeting · doi:10.1109/ias.1992.244307 · Cited by 370 · cited 3×
“Moreover, the current dc component generates unequal current stress in the upper and lower transistors in the inverter, which may cause thermal defects in the transistors [1].”
BackgroundInfluentialFault detection and isolation on a PWM inverter by knowledge-based model
Peuget, R., Courtine, S., & Rognon, J. P. (2002) · IAS '97. Conference Record of the 1997 IEEE Industry Applications Conference Thirty-Second IAS Annual Meeting · doi:10.1109/ias.1997.629048 · Cited by 304 · cited 2×
“[15] suggested the open switch fault detection by analyzing the current vector trajectory and of the instantaneous frequency in the faulty mode.”
BackgroundMethodFault-Tolerant Voltage-Fed PWM Inverter AC Motor Drive Systems
de Araujo Ribeiro, R. L., Jacobina, C. B., da Silva, E. R. C., & Lima, A. M. N. (2004) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2004.825284 · Cited by 299 · cited 1×
“A simplified version of [7] has been developed in [8], where only fast-acting semiconductor fuses are used to isolate”
BackgroundFuchs, F. W. (2004) · IECON'03. 29th Annual Conference of the IEEE Industrial Electronics Society (IEEE Cat. No.03CH37468) · doi:10.1109/iecon.2003.1280259 · Cited by 270 · cited 1×
“IGBT are available in the literature [13]–[16].”
Research works printed but not linked: 2
- schwab, 2003, Reliability evaluation of a permanent magnet synchronous motor drive for an automotive application, Proc Eur Conf Power Electron Appl
- thorsen, 1995, A survey of the reliability with an analysis of faults on the variable frequency drives in industry, Proc Conf Rec 6th Eur Power Electron Appl Conf, 1033
Cited by
Items 201–283 of 283
Fault tolerant control of Small Distributed Generation Systems
Consoli, A., Cacciato, M., Scarcella, G., & Scelba, G. (2012) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce.2012.6342225 · Cited by 3
“Different solutions have been proposed in order to mitigate short-circuit and open-circuit faults of the switching devices, but most of them require additional components such as power devices, thyristors and fuses added to standard inverters for fault-tolerant operation thus increasing the cost and complexity of the…”
BackgroundHe, L., Zhao, J., Wu, F., & Yang, H. (2017) · IEEE Conference on Industrial Electronics and Applications (ICIEA) · doi:10.1109/iciea.2017.8283015 · Cited by 3
“Fault topology reconfiguration and fault-tolerant control algorithm are facilitated implementation [1-7].”
BackgroundPost-Fault Operation of Fault-Tolerant Three Phase Surface Mounted PMSM
Veeramaneni, N. D., & Kanagaraj, R. (2019) · National Power Electronics Conference (NPEC) · doi:10.1109/npec47332.2019.9034793 · Cited by 3
“In [11], [12] a four leg half-bridge converter is used for post-fault operation.”
MethodFault-Tolerant Operation of Bidirectional ZSI-Fed Induction Motor Drive for Vehicular Applications
Sharma, V., Hossain, M. J., & Mukhopadhyay, S. C. (2022) · Energies · doi:10.3390/en15196976 · Cited by 3
Song, L., Wang, R., Guo, X., Liao, M., Wang, D. J., Jiang, Z., & Chen, Z. (2023) · Journal of Failure Analysis and Prevention · doi:10.1007/s11668-023-01826-1 · Cited by 3
“T 2 3LIs are widely used in areas such as electric propulsion systems for new energy vehicles due to their advantages of low switch losses [1], good fault-tolerant control performance [2], and high stability [3, 4].”
Lai, S., Chen, G., She, Z., Mo, L., & Qing, X. (2024) · IEEE International Conference on Industrial Technology (ICIT) · doi:10.1109/icit58233.2024.10541021 · Cited by 3
“In contrast, OC faults, while less critical, can result in secondary failures and high maintenance costs with prolonged operation [2].”
BackgroundDas, P. S., & Kim, K. (2014) · International Journal of Control and Automation · doi:10.14257/ijca.2014.7.11.39 · Cited by 3
Fault-tolerance control for a dual-PMSM drive system
Tseng, S., Liu, T., Hsu, J., Ramelan, L. R., & Firmansyah, E. (2015) · IEEE International Future Energy Electronics Conference (IFEEC) · doi:10.1109/ifeec.2015.7361381 · Cited by 3
“Some fault-detection methods have been published [11]-[12].”
Digital short-circuit diagnosis and reconfiguration of a fault tolerant VSI
Oliveira, A. B. M., Moreno, R. L., & Ribeiro, Ê. R. (2017) · IEEE Annual Southern Power Electronics Conference · doi:10.1109/spec.2017.8333586 · Cited by 3
“In fault-tolerant systems, there are also delays in fault isolation procedures and inverter topology reconfiguration due to the use of AI techniques: fault detection [8] and diagnosis [3], [9] and [10].”
Inverter and Controller for Highly Available Permanent Magnet Synchronous Drives
Errabelli, R. R. (2012) · Technischen Universität Darmstadt · doi:10.26083/tuprints-00003027 · Cited by 6
Self-citationLin, H., Xia, D., Feng, L., Zhou, X., Li, J., & Zhao, F. (2019) · International Conference on Electrical Machines and Systems (ICEMS) · doi:10.1109/icems.2019.8921790 · Cited by 2
Design of an Improved Q-ZSI with Fault Tolerance for EV Applications
Singh, K. V., Koul, S., Bansal, H. O., & Singh, D. (2019) · International Conference on Recent Developments in Control, Automation & Power Engineering (RDCAPE) · doi:10.1109/rdcape47089.2019.8979033 · Cited by 2
“Once the gating signal has been shifted to the redundant arm, the output corresponding to that phase will also be taken now from the redundant arm[13].”
BackgroundReal time emulator for parallel connected dual-PMSM sensorless control
Sahri, K., Pietrzak‐David, M., Baghli, L., & Kheloui, A. (2021) · International Journal of Power Electronics and Drive Systems/International Journal of Electrical and Computer Engineering · doi:10.11591/ijpeds.v12.i3.pp1390-1404 · Cited by 2
Three-Phase Buck-Boost Inverter with Reduced Current Ripple
Khan, A. A., Khan, U. A., & Ahmad, S. (2021) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce47101.2021.9595511 · Cited by 2
Flux-Based Predictive Control for Two-Level Post-Fault Tolerant Inverters Fed IM Drives
Zouari, W., & Badsi, B. E. (2025) · International Multi-Conference on Systems, Signals & Devices (SSD) · doi:10.1109/ssd64182.2025.10989819 · Cited by 2
“In order to reduce the costs, just a fourth leg was added to the converter as a rescue leg in [6] and also in [7], where the redundant leg is added to replace the faulted one.”
New robust controller design for voltage source inverters in microgrids
Syed, A. H., & Abido, M. A. (2014) · Mediterranean Conference on Control and Automation (MED) · doi:10.1109/med.2014.6961461 · Cited by 2
“In [20], a two level fault tolerant VSI is designed for a PM drive which consist of 3 legs.”
BackgroundPower flow control with losses minimization and fault tolerance for PMSG
Catuogno, G. R., Forchetti, D. G., García, G. O., & Leidhold, R. (2012) · Annual Conference of the IEEE Industrial Electronics Society (IECON) · doi:10.1109/iecon.2012.6389326 · Cited by 2
Sivakumar, M., & Parvathi, R. M. S. (2014) · Cited by 2
Harmonic analysis based fault detection for a five-phase PMSG diode rectifier conversion chain
Liang, C., Yao, G., Ahmed, M. A., Claire, J. C. L., & Benkhoris, M. F. (2016) · IEEE Conference on Industrial Electronics and Applications (ICIEA) · doi:10.1109/iciea.2016.7603923 · Cited by 2
“For this reason, control algorithms in health [1-4] and fault [5-11] mode have been proposed.”
BackgroundRemedial control strategies for a three-phase PM BLDC drive under VSI faults
Jha, R. K., Garlapati, S., Keshri, R. K., & Buja, G. (2014) · IEEE International Conference on Power Electronics, Drives and Energy Systems · doi:10.1109/pedes.2014.7041966 · Cited by 2
“The above-mentioned situations and the arrangements for fault-tolerant drive operation have been discussed in [5-7].”
BackgroundAn Optimization Approach to Design Robust Controller for Voltage Source Inverters
Syed, A. H., & Abido, M. A. (2017) · Elsevier eBooks · doi:10.1016/b978-0-08-101753-1.00006-1 · Cited by 2
A proposed voltage technique for inverter open fault-circuit detection based on SVM strategy
Azzeddine, B., & Chérif, B. D. E. (2017) · IEEE International Conference on Power Electronics and Drive Systems (PEDS) · doi:10.1109/peds.2017.8289100 · Cited by 2
Digital diagnosis of short-circuit failures and reconfiguration of a single-phase VSI
Oliveira, A. B. M., Simões, M. G., Moreno, R. L., & Ribeiro, Ê. R. (2017) · IEEE Annual Southern Power Electronics Conference · doi:10.1109/spec.2017.8333554 · Cited by 2
“In fault-tolerant systems, reconfiguration of the inverter is performed in two situations: either with the detection method [9] or with the fault diagnosis [7], [8] and [10].”
BackgroundMethodRasyadan, A., Ibrahim, Z., Dir, T. M. A. T., & Yaacob, S. (2018) · International Conference on Computational Approach in Smart Systems Design and Applications (ICASSDA) · doi:10.1109/icassda.2018.8477626 · Cited by 3
A Fault-tolerant parallel inverter applied to micro-grid
Shi, X., Peng, J., Qiu, Z., & Xiong, W. Z. (2018) · International Power Electronics Conference (IPEC) · doi:10.23919/ipec.2018.8507759 · Cited by 3
“Literatures [7-9] proposed the redundant fault-tolerant inverter.”
Yaacob, S., Rasyadan, A., & Krishnanf, P. (2021) · IOP Conference Series Materials Science and Engineering · doi:10.1088/1757-899x/1127/1/012024 · Cited by 2
“The power inverter is known to be the weakest component in the drive system with around 38% of the drive faults are due to their power switch devices [1-3].”
BackgroundCuk-Based Single-Phase Inverter Design for PV Array Systems
Narasimhan, A. (2021) · Studies in Infrastructure and Control · doi:10.1007/978-981-16-4663-8_13 · Cited by 2
Abbaspour, H., & Kojabadi, H. M. (2022) · International Journal of Circuit Theory and Applications · doi:10.1002/cta.3459 · Cited by 2
“By adding three auxiliary legs to the topology, the one-time OC fault of the switches of all three legs of the inverter can be fixed.(16,17)”
BackgroundResearch on the High Reliable Electromagnetic Stirring Power Supply
Xiang, X., Luo, A., Li, Y., Chen, Y., Li, Y., & Peng, P. (2021) · Applied Sciences · doi:10.3390/app11219874 · Cited by 1
Design and Implementation of a Ground Power Unit Based on the Fault-Tolerant Inverter
Abbaspour, H., Kojabadi, H. M., & Farhadi‐Kangarlu, M. (2022) · Electric Power Components and Systems · doi:10.1080/15325008.2022.2150915 · Cited by 1
“By adding three auxiliary legs to the topology, the one-time OC fault of the switches of all three legs of the inverter can be fixed [16, 17].”
BackgroundMaximal Force Capability Strategy for Short-Circuit Fault-Tolerant of AMB Power Electronics Drive
Shuai, Y., Zhou, M., Chen, Y., Xie, Y., Ding, J., Jiang, D., & Liu, Z. (2025) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2025.3574652 · Cited by 1
Khan, M. A. A., Alam, S., Huang, L.-Y., Sarwar, A., Zaid, M., Liu, H., Tariq, M., & Ahmad, S. (2026) · Energy Reports · doi:10.1016/j.egyr.2026.109273 · Cited by 2
Model silnika PMSM do badań symulacyjnych sterowania tolerującego uszkodzenia
Siembab, K. (2013) · Poznan University of Technology Academic Journals Electrical Engineering · Cited by 1
Gupta, S., & Tripathi, A. (2013) · Cited by 1
Inverter fault Analysis in Permanent Magnet Synchronous Motor using Matlab & Simulink
Gupta, S., Srivastava, A., & Tripathi, A. (2013) · Cited by 1
Reducing DC link voltage unbalance in a fault-tolerant inverter
Boscaino, V., Tommaso, A. O. D., Genduso, F., & Miceli, R. (2014) · International Power Electronics and Motion Control Conference (EPE-PEMC) · doi:10.1109/epepemc.2014.6980694 · Cited by 1
“After fault occurrence, the redundant circuitry replaces the faulted part of the original circuit [14]–[17], gate drive signals of the faulted part are connected to the redundant section modifying neither the modulation strategy nor the 16th International Power Electronics and Motion Control Conference and Exposition…”
BackgroundA novel strategy to design enhanced performance robust controller for standalone VSI
Syed, A. H., & Abido, M. A. (2016) · Journal of the Franklin Institute · doi:10.1016/j.jfranklin.2016.12.013 · Cited by 1
Design of Cuk Converter based three phase inverter by fuzzy controller
Gaikwad, S. B., & Joshi, S. D. (2017) · International Conference on Computing Communication Control and automation · doi:10.1109/iccubea.2017.8463958 · Cited by 1
“The fuzzy variables are denoted by linguistic variables that are are positive large that is (PL), positive medium that is (PM), positive small that is (PS), zero that is (Z), Negative small that is (NS), negative medium that is (NM), negative large that is (NL), for all three variables [9].”
BackgroundHigh Frequency Transformer Based Improved Gamma ZSI with Lossless Snubber
Aleem, Z., Winberg, S. L., Iqbal, A., & Al-Hitmi, M. A. E. (2018) · Annual Conference of the IEEE Industrial Electronics Society (IECON) · doi:10.1109/iecon.2018.8592806 · Cited by 1
Fault Detection and Isolation on a Five-level PWM Inverter applied to the electric vehicle system
Rtibi, W., M’barki, L., & Ayadi, M. (2019) · International Conference on Sciences and Techniques of Automatic Control and Computer Engineering · doi:10.1109/sta.2019.8717229 · Cited by 1
“As a result, it is imperative to find the appropriate way that protects the system and detect the defection as soon as possible [11] [12].”
BackgroundA Secondary Reconfigurable Inverter and Its Control Strategy
Li, Y., Peng, X., & Chen, Y. (2020) · Applied Sciences · doi:10.3390/app10207021 · Cited by 1
“Redundant fault-tolerant strategies include switch-redundant topologies [9], neutral leg topologies [10], additional phase leg topologies [11], cascaded inverter topology [12], etc.”
BackgroundFault-Tolerant PV Multistring Inverter
Renaudineau, H., Paradell, P., Trilla, L., Filbà-Martínez, À., & Domínguez‐García, J. L. (2021) · IEEE Green Technologies Conference (GreenTech) · doi:10.1109/greentech48523.2021.00023 · Cited by 1
Kumar, K. S., & Lavanya, V. U. P. (2022) · Advances in transdisciplinary engineering · doi:10.3233/atde220754 · Cited by 2
Fault Detection and Isolation in Electric Vehicle Powertrain
Jombo, G., & Zhang, Y. (2022) · Wiley eBooks · doi:10.1002/9781119801078.ch5 · Cited by 1
Dewangan, N. K., Jena, K., Kumar, D., Janardhan, K., Kumar, B. H., & Verma, D. (2023) · IEEE International Conference on Renewable Energy and Sustainable E-Mobility (RESEM) · doi:10.1109/resem57584.2023.10236350 · Cited by 1
“Active power semiconductor devices, drivers, and source failure is the leading cause of complete inverter failure [9-10].”
BackgroundSakka, M. A., Hosseinabadi, F., Geury, T., Baghdadi, M. E., Sakka, M. A., & Hegazy, O. (2024) · IEEE Open Journal of Power Electronics · doi:10.1109/ojpel.2024.3352117 · Cited by 1
“A crucial drawback of using electric motor drives is their high failure rate compared to mechanical systems, mainly due to the semiconductor switches faults of the power inverter [3].”
BackgroundModel-Based Fault Tolerant Design of Redundant Electric Fuel Metering System for Aircraft
Yamamoto, Y., MURAOKA, M., Sugawara, H., Umeki, Y., SHIBUYA, Y., & Oyori, H. (2024) · JOURNAL OF THE JAPAN SOCIETY FOR AERONAUTICAL AND SPACE SCIENCES · doi:10.2322/jjsass.72.117 · Cited by 1
Improvement in control and gain aspects of impedance source inverters and converters
Aleem, Z. (2019) · Open University of Cape Town (University of Cape Town) · Cited by 1
Zhang, X. (2022) · theses.fr (ABES) · doi:10.70675/d2280d2cz2547z421bzbc33z8c99545774ab · Cited by 3
Fault-Tolerant Control Research of Vehicle-Mounted 5-Phase Inverters
Zhang, J. M., Yuan, Y., & Wang, H. (2012) · Advanced materials research · doi:10.4028/www.scientific.net/amr.588-589.397
“When Uout is located in different sectors, Tbon and Tcon take different values [4, 5, 6].”
BackgroundA fault tolerant single sided matrix converter for flight control actuation systems
Huang, X., Jin, M., Zhang, J., Lu, Q., Fang, Y., Goodman, A., & Gerada, C. (2012) · Frontiers of Information Technology & Electronic Engineering · doi:10.1631/jzus.c1200164
“Recently, much research has been carried out on the development of fault tolerant voltage source inverters (VSIs) (de Araujo Ribeiro et al., 2004; Argile et al., 2008; Errabelli and Mutschler, 2012).”
BackgroundDjebarri, S., Charpentier, J., Scuiller, F., Benbouzid, M., & Electrique, G. (2014)
Boscaino, V., Tommaso, A. O. D., Genduso, F., & Miceli, R. (2015) · AEIT International Annual Conference · doi:10.1109/aeit.2015.7415268
“After fault occurrence, the redundant circuitry replaces the faulted part of the original circuit [5]–[7].”
BackgroundKang, K.-H., Yu, S.-J., Lee, G.-H., & Lee, B.-H. (2015) · Journal of Magnetics · doi:10.4283/jmag.2015.20.4.421
Stanowisko do badania układów napędowych z silnikiem PM BLDC
Skóra, M. (2014) · Prace Naukowe Instytutu Maszyn, Napędów i Pomiarów Elektrycznych Politechniki Wrocławskiej. Studia i Materiały
A DC-Link Voltage Compensation Method for Dual Permanent Magnet Synchronous Motor Drive
Lin, H., Li, F., Hu, B., Zhou, X., Si, L., Chen, J., Li, Y., Chen, J., Yan, M., & Dong, Y. (2018) · IEEE Advanced Information Management, Communicates, Electronic and Automation Control Conference (IMCEC) · doi:10.1109/imcec.2018.8469230
A Cuk Converter Based Fault Detection and Correction Topology for BLDC Drives in Electric Vehicles
Anjali, V. S., Kuncheria, J. T., & George, R. (2018) · International Conference on Current Trends towards Converging Technologies (ICCTCT) · doi:10.1109/icctct.2018.8551101
“About 35% of all motor system faults are due to the power semiconductor devices and the power stress [7] in the three phase inverters contributes to about 40% of faults.”
BackgroundSousa, T. J. C., Monteiro, V., Martins, J. S., Fernandes, J. C. A., & Afonso, J. L. (2018) · APCA International Conference on Control and Soft Computing (CONTROLO) · doi:10.1109/controlo.2018.8514547
“The ability to control the output voltage and frequency from a constant dc voltage source made VSIs attractive for electric motor drive systems, such as adjustable speed drives [1][2] and the increasingly proliferative electric vehicles [3][4].”
BackgroundDesign of predictive controllers for fault‐tolerant surface‐mounted PMSM drive systems
Liu, T., & Tu, Y. (2019) · The Journal of Engineering · doi:10.1049/joe.2019.0005
Praca napędu z silnikiem PM BLDC w warunkach awarii tranzystora komutatora elektronicznego
Skóra, M. (2016) · PRZEGLĄD ELEKTROTECHNICZNY · doi:10.15199/48.2016.06.09
On-line Temperature Monitoring of Permanent Magnet Synchronous Machines
Xiao, S. (2019) · White Rose eTheses Online (University of Leeds, The University of Sheffield, University of York)
An Inverter with Large Fault-tolerant Space for Battery Storage in Islanded Microgrid
Li, Y., Peng, X., & Yang, Z. R. (2019) · Annual Conference of the IEEE Industrial Electronics Society (IECON) · doi:10.1109/iecon.2019.8926618
“The power semiconductor device faults account for about 40% of the three-phase inverter failures occurring due to the power switches [3-4].”
BackgroundYelamarthi, B. S. S. G., & Sandepudi, S. R. (2019) · 2019 International Conference on Power Electronics, Control and Automation (ICPECA) · doi:10.1109/icpeca47973.2019.8975479
“Once the fault is isolated, reconfiguration of the inverter is done automatically and post-fault control technique has to apply for restoring normal operation [7-25].”
BackgroundMethodPerformance Analysis of Buck Boost DC/AC Converter With Switched Inductor Network
Kumari, K., & Sharma, A. K. (2019) · International Conference on Power Energy, Environment and Intelligent Control (PEEIC) · doi:10.1109/peeic47157.2019.8976551
“The voltage supply electrical converter will perform only buck operate used in [6].”
MethodUsing FTC for a 7-Leg Inverter to Ensure Operational Continuity of Two Machines in Case of Fault
Aboub, Y., Bouchafaa, F., Tabbache, B., Mekhilef, S., Benbouzid, M., & Benlahbib, B. (2019) · International Conference on Sustainable Renewable Energy Systems and Applications (ICSRESA) · doi:10.1109/icsresa49121.2019.9182631
Fault-Tolerance of Electric Drive with Field Regulated Reluctance Machine
Сычев, Д. А., Su, J.-Y., Huang, S., & Huang, Y. (2021) · International Conference on Industrial Engineering, Applications and Manufacturing (ICIEAM) · doi:10.1109/icieam51226.2021.9446414
Liu, T., & Wang, Y. (2021) · Frontiers in Electronics · doi:10.3389/felec.2021.670077
Optimal open loop control for a fast transition from normal to active-short-circuit operation
Wagner, P., Hirsch, M., Götting, G., & Reuss, H.-C. (2021) · European Conference on Power Electronics and Applications · doi:10.23919/epe21ecceeurope50061.2021.9570445
“In literature different control strategies for a post-fault operation with a faulty PSM or VSI are presented in [1], [2], [3], [4], [5].”
BackgroundHybrid Motor Drives: Characterization and Control
Hadley, B. (2011) · FIU - Digital Commons (Florida International University) · doi:10.25148/etd.fi11080809
“The physical topology of the motor drive is that of a standard three-phase voltage source inverter, a common DC bus, with an input energy source [36-37].”
BackgroundGrid-Connected Photovoltaic System Based On the Switched Coupled - Inductor Quasi-Z- Source Inverter
K.P.Nithya, S. M. P. (2015) · International Journal of Advanced Research in Electrical Electronics and Instrumentation Engineering · doi:10.15662/ijareeie.2015.0407014
2012 Index IEEE Transactions on Power Electronics Vol. 27
(2012) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2023.3278588 · Cited by 1
Open-circuit fault-tolerant control of power switch for two-level three-phase motor inverter
Ning, Y., Shao, D., Wang, Y., & Wei, Y. (2023) · IEEE PELS Students and Young Professionals Symposium (SYPS) · doi:10.1109/syps59767.2023.10268141
Analysis of Induction Motor Drive Systems
Pratap, E. A. M. (2023) · International Journal on Recent and Innovation Trends in Computing and Communication · doi:10.17762/ijritcc.v11i7.10059
Enhancing Fault Tolerant Ability of Motor Drive System Using Novel Open-end Topology
You, J., Liu, Z., Jiang, D., Zhang, J., Li, B., & Huang, Y. (2024) · International Power Electronics and Motion Control Conference (EPE-PEMC) · doi:10.1109/ipemc-ecceasia60879.2024.10567752
“According to statistics, more than 80% of converter failures are caused by abnormal power switching devices, and 38% are directly caused by damage to power switching devices [2].”
BackgroundImpact Analysis and Modified Topology of VSI Under Switch Fault Conditions
Prema, D. K., Sai, B. S. V., Bhattacharya, A., & Chatterjee, D. (2025) · International Conference on Multi-Agent Systems for Collaborative Intelligence (ICMSCI) · doi:10.1109/icmsci62561.2025.10894695
“In this work, the focus is driven towards the 3P-5L inverters with redundant leg [12].”
Saidji, R., Boudinar, A. H., Khodja, M.-E.-A., & Aimer, A. F. (2024) · Algerian Journal of Research and Technology · doi:10.58681/ajrt.24080205
Comparison and Simulated Result of Three and Five Phase Permanent Magnet Synchronous Motor (PMSM)
Rana, V. A., Baria, J. C., & Arya, S. (2014)
A Reliable Control Strategy for Dual Induction Motor Drive System Consisting of Five-Leg Inverter
Lee, E., Lee, J., & Lee, J.-S. (2026) · Applied Sciences · doi:10.3390/app16010530
Signature-Current Analysis for Fault-Tolerant PMSM Drive SystemsPreprint
Moujahed, M., Mahdhi, H. B., Mourad, S., Slimene, M. B., Khlifi, M. A., & Azza, H. B. (2026) · Research Square · doi:10.21203/rs.3.rs-8467194/v1
Maamouri, R. (2017) · theses.fr (ABES) · doi:10.70675/d6cec70cz6be5z467az9a94zb5eae7e979a8 · Cited by 3
Wang, G., Liu, H., Liu, Z., You, J., Zhu, R., Huang, C., Jiang, D., & Qu, R. (2026) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2026.3677582
“Switches experience up to tens of thousands of switching operations per second under these extreme conditions, resulting in a higher likelihood of failure due to the immense electromagnetic and thermal loads [8].”
Ajmi, A., Trabelsi, M., Charpentier, J., & Mimouni, M. F. (2026) · Electronics · doi:10.3390/electronics15122527
Metadata
- Authors
- Errabelli, R. R., & Mutschler, P.
- Affiliations
- Technische Universität Darmstadt (DE)
- Venue
- IEEE Transactions on Power Electronics
- Published
- 2012-02
- Volume
- 27
- Issue
- 2
- Pages
- 500-508
- ISSN
- 0885-8993 (ISSN-L)
- 1941-0107
- OpenAlex
- W2079590925
- Cited by
- 278
- References
- 19
- Citations by year
- 2026: 5 · 2025: 6 · 2024: 10 · 2023: 10 · 2022: 17 · 2021: 25 · 2020: 19 · 2019: 23 · 2018: 25 · 2017: 25 · 2016: 22 · 2015: 23 · 2014: 29 · 2013: 24 · 2012: 13
- FWCI
- 15.23
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- IEEE Transactions on Power Electronics (publishedVersion)
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Multilevel Inverters and Converters
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Electric Motor Design and Analysis
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Sensorless Control of Electric Motors
- Keywords
- fault-tolerant inverter, voltage source inverter, permanent magnet synchronous motor, short-circuit faults, open-circuit fault, field-oriented control
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.