Fault-Tolerant Voltage Source Inverter for Permanent Magnet Drives
The DOI matches its Crossref record; 18 of the 19 references it cites were found in a registry or an index.
Abstract
In this paper, a two-level fault-tolerant voltage source inverter (VSI) for permanent magnet drives is systematically designed and tested. A standard two-level inverter consists of three legs. In this case of fault-tolerant inverter, a redundant leg is added that replaces the faulted leg. Faulted leg isolation and redundant leg insertion are done by using independent back-to-back-connected thyristors. The proposed inverter provides tolerance to both short-circuit and open-circuit faults of the switching devices. The postfault performance is the same as the normal prefault operation and fault compensation is fast enough such that there is negligible disturbance in the drive operation. The fault tolerance of the inverter is verified using field-oriented control of a permanent magnet synchronous motor.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“According to [238], [239], power semiconductor device damages account for approximately 35% of all ASD faults.”
From Fault Diagnosis and Fault-Tolerant Control of PMSM Drives–State of the Art and Future Challenges (2022) · cites this paper as [239]
In the citing paper
“Recently, phase redundancy approaches [239], [309] have gained popularity due to their full fault recovery without oversizing the drive.”
From Fault Diagnosis and Fault-Tolerant Control of PMSM Drives–State of the Art and Future Challenges (2022) · cites this paper as [239]
Citations
Cites
Welchko, B. A., Lipo, T. A., Jahns, T. M., & Schulz, S. E. (2004) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2004.830074 · Cited by 724 · cited 1×
“Several fault-tolerant topologies are available in the literature [5]; some of them reconfigure the standard inverter topology and reformulate the current references so that the rotating”
BackgroundFault detection of open-switch damage in voltage-fed PWM motor drive systems
de Araujo Ribeiro, R. L., Jacobina, C. B., da Silva, E. R. C., & Lima, A. M. N. (2003) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2003.809351 · Cited by 441 · cited 2×
“According to [14], the open-circuit fault of the IGBT can be detected by inserting voltage sensors at desired locations.”
BackgroundMethodInvestigation of fault modes of voltage-fed inverter system for induction motor drive
Kastha, D., & Bose, B. K. (1994) · IEEE Transactions on Industry Applications · doi:10.1109/28.297920 · Cited by 386
Fault detection and isolation on a PWM inverter by knowledge-based model
Peuget, R., Courtine, S., & Rognon, J.-P. (1998) · IEEE Transactions on Industry Applications · doi:10.1109/28.739017 · Cited by 384
Experimental fault-tolerant control of a PMSM drive
Bolognani, S., Zordan, M., & Zigliotto, M. (2000) · IEEE Transactions on Industrial Electronics · doi:10.1109/41.873223 · Cited by 382
A strategy for improving reliability of field-oriented controlled induction motor drives
Liu, T.-H., Fu, J.-R., & Lipo, T. A. (1993) · IEEE Transactions on Industry Applications · doi:10.1109/28.245714 · Cited by 374 · cited 1×
“faulted leg has to be connected to the midpoint of the dc voltage link, created using the use of two capacitors [6].”
MethodInvestigation of fault modes of voltage-fed inverter system for induction motor drive
Kastha, D., & Bose, B. K. (2003) · Conference Record of the 1992 IEEE Industry Applications Society Annual Meeting · doi:10.1109/ias.1992.244307 · Cited by 370 · cited 3×
“Moreover, the current dc component generates unequal current stress in the upper and lower transistors in the inverter, which may cause thermal defects in the transistors [1].”
BackgroundInfluentialFault detection and isolation on a PWM inverter by knowledge-based model
Peuget, R., Courtine, S., & Rognon, J. P. (2002) · IAS '97. Conference Record of the 1997 IEEE Industry Applications Conference Thirty-Second IAS Annual Meeting · doi:10.1109/ias.1997.629048 · Cited by 304 · cited 2×
“[15] suggested the open switch fault detection by analyzing the current vector trajectory and of the instantaneous frequency in the faulty mode.”
BackgroundMethodFault-Tolerant Voltage-Fed PWM Inverter AC Motor Drive Systems
de Araujo Ribeiro, R. L., Jacobina, C. B., da Silva, E. R. C., & Lima, A. M. N. (2004) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2004.825284 · Cited by 299 · cited 1×
“A simplified version of [7] has been developed in [8], where only fast-acting semiconductor fuses are used to isolate”
BackgroundFuchs, F. W. (2004) · IECON'03. 29th Annual Conference of the IEEE Industrial Electronics Society (IEEE Cat. No.03CH37468) · doi:10.1109/iecon.2003.1280259 · Cited by 270 · cited 1×
“IGBT are available in the literature [13]–[16].”
Research works printed but not linked: 2
- schwab, 2003, Reliability evaluation of a permanent magnet synchronous motor drive for an automotive application, Proc Eur Conf Power Electron Appl
- thorsen, 1995, A survey of the reliability with an analysis of faults on the variable frequency drives in industry, Proc Conf Rec 6th Eur Power Electron Appl Conf, 1033
Cited by
Study and Handling Methods of Power IGBT Module Failures in Power Electronic Converter Systems
Choi, U.-M., Blaabjerg, F., & Lee, K.-B. (2015) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2014.2373390 · Cited by 700
The state of the art of wind energy conversion systems and technologies: A review
Cheng, M., & Zhu, Y. (2014) · Energy Conversion and Management · doi:10.1016/j.enconman.2014.08.037 · Cited by 600
“Various topologies have been proposed to endow a standard three-phase converter with fault tolerant capabilities [108,109].”
BackgroundSurvey of fault-tolerance techniques for three-phase voltage source inverters
Mirafzal, B. (2014) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2014.2301712 · Cited by 440
“duced for Y-connected three-phase motor drives in which an auxiliary fourth leg is added to the standard two-level inverter topology [8], [9], [26]–[32], and the fourth leg is connected”
BackgroundA New Boost Switched-Capacitor Multilevel Converter With Reduced Circuit Devices
Barzegarkhoo, R., Moradzadeh, M., Zamiri, E., Madadi Kojabadi, H., & Blaabjerg, F. (2018) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2017.2751419 · Cited by 389
“can be based on either impedance Z-source or multilevel voltage source inverters (MLVSIs) [3]–[9].”
BackgroundEstima, J. O., & Marques Cardoso, A. J. (2013) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2012.2188877 · Cited by 377
Fault Diagnosis and Fault-Tolerant Control of PMSM Drives–State of the Art and Future Challenges
Orlowska-Kowalska, T., Wolkiewicz, M., Pietrzak, P., Skowron, M., Ewert, P., Tarchala, G., Krzysztofiak, M., & Kowalski, C. T. (2022) · IEEE Access · doi:10.1109/access.2022.3180153 · Cited by 328
“According to [238], [239], power semiconductor device damages account for approximately 35% of all ASD faults.”
BackgroundWang, T., Xu, H., Han, J., Elbouchikhi, E., & Benbouzid, M. E. H. (2015) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2015.2393373 · Cited by 273
“If an inverter system runs continuously under the abnormal conditions, this would cause other failures and bring serious consequences [16].”
BackgroundCurrent Residual Vector-Based Open-Switch Fault Diagnosis of Inverters in PMSM Drive Systems
An, Q.-T., Sun, L., & Sun, L.-Z. (2015) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2014.2360834 · Cited by 226
PWM-VSI Fault Diagnosis for a PMSM Drive Based on the Fuzzy Logic Approach
Yan, H., Xu, Y., Cai, F., Zhang, H., Zhao, W., & Gerada, C. (2019) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2018.2814615 · Cited by 216
Mohammadpour, A., Sadeghi, S., & Parsa, L. (2014) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2013.2247011 · Cited by 210
A Practical Thermal Model for the Estimation of Permanent Magnet and Stator Winding Temperatures
Kral, C., Haumer, A., & Lee, S. B. (2014) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2013.2253128 · Cited by 206
“T e p = T e p [1] + T e p [2] + T e p [3] + T e p [4] + T e p [5]”
Nguyen, N. K., Meinguet, F., Semail, E., & Kestelyn, X. (2016) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2014.2386299 · Cited by 193
Joseph, A., & Chelliah, T. R. (2018) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2017.2707397 · Cited by 180
“In power converters, open and short-circuit faults are due to: 1) electromagnetic interference; 2) malfunction in the driver circuit; 3) rapid voltage dip/swell; 4) auxiliary power supply failure; and 5) avalanche stress, and temperature overshoot in power devices [83], [84].”
BackgroundSwitched-Coupled-Inductor Quasi-Z-Source Inverter
Ahmed, H. F., Cha, H., Kim, S.-H., & Kim, H.-G. (2015) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2015.2414971 · Cited by 173
Mohammadpour, A., & Parsa, L. (2012) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2012.2223717 · Cited by 158
A Fault-Tolerant Permanent-Magnet Traction Module for Subway Applications
Wang, W., Cheng, M., Zhang, B., Zhu, Y., & Ding, S. (2013) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2013.2266377 · Cited by 151
“The traditional protection method is to lock the fault VSI and isolate the corresponding PMSM [24].”
BackgroundMethodMwasilu, F. A., & Jung, J. (2015) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2015.2495240 · Cited by 143
“Most of the recent researches on the FTC of the PMSMs are concerned about the inverter failures [11]–[13] or faulty motor windings [14].”
BackgroundBadsi, B. E., Bouzidi, B., & Masmoudi, A. (2012) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2012.2225449 · Cited by 126
Tousizadeh, M., Seng, H., Selvaraj, J. A.-L., Rahim, N. A., & Ooi, B. (2018) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2018.2850006 · Cited by 123
A Fault-Tolerant Direct Controlled PMSG Drive for Wind Energy Conversion Systems
Freire, N. M. A., & Cardoso, A. J. M. (2013) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2013.2251734 · Cited by 120
“A redundant leg can be connected to all the converter phases through triodes for alternating current (TRIACs) [5], [13], [14], permitting the replacement of the faulty leg and keeping the same converter topology.”
BackgroundDetection and Discrimination of Open Phase Fault in Permanent Magnet Synchronous Motor Drive System
Hang, J., Zhang, J., & Cheng, M. (2015) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2015.2479399 · Cited by 115
“For example, reconfiguration of the inverter may be adopted as the TSF occurs, where the performances of the PMSM at postfault operation are the same as those at prefault operation [17], [18].”
MethodPMSM Open-Phase Fault-Tolerant Control Strategy Based on Four-Leg Inverter
Zhou, X., Sun, J., Li, H., Lü, M., & Zeng, F. (2019) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2019.2925823 · Cited by 115
A Single-Stage Three-Phase Inverter Based on Cuk Converters for PV Applications
Darwish, A., Holliday, D., Ahmed, S., Massoud, A. M., & Williams, B. W. (2014) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2014.2313185 · Cited by 115
“For this reason, a boost dc–dc converter is needed when the required ac peak output voltage is greater than the input dc voltage [4].”
BackgroundCost-Effective Three-Phase PMSM Drive Tolerant to Open-Phase Fault
Kontarcek, A., Bajec, P., Nemec, M., Ambrozic, V., & Nedeljkovic, D. (2015) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2015.2437357 · Cited by 106
“Several authors have dealt with this type of postfault operation when supplying either induction [14]–[16] or permanent-magnet motors [17]–[19], as well as with related general postfault SPWM inverter control strategy [20].”
BackgroundDiagnosis and Fault-Tolerant Control of Three-Phase AC–DC PWM Converter Systems
Im, W.-S., Kim, J.-M., Lee, D., & Lee, K. (2013) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2013.2255111 · Cited by 104
“Therefore, both diagnostic methods and faulttolerant control methods are required [3]–[6].”
MethodYan, H., Xu, Y., Zou, J., Fang, Y., & Cai, F. (2017) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2017.2776939 · Cited by 101
“normally [5], [6].”
Genduso, F., Cecati, C., Tommaso, A. O. D., Miceli, R., & Galluzzo, G. R. (2015) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2015.2402645 · Cited by 99
“[4]–[7]; on the contrary, nonredundant topologies, assuming temporary performance degradation, on the basis of some modified control strategies exploit the possibility of minimum additional components for reconfiguration and operation [4], [8], [9].”
Hu, K., Liu, Z., Yang, Y., Iannuzzo, F., & Blaabjerg, F. (2020) · IEEE Access · doi:10.1109/access.2020.2994368 · Cited by 99
Garg, P., Essakiappan, S., Krishnamoorthy, H. S., & Enjeti, P. N. (2014) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2014.2361905 · Cited by 101
“More recently, phase-redundant approaches [13], [27]–[29] have gained pop-”
BackgroundTousizadeh, M., Seng, H., Selvaraj, J. A.-L., Rahim, N. A., & Ooi, B. (2018) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2018.2884759 · Cited by 89
“and several fault-tolerant three-phase induction motor (3ph-IM) drive topologies have been discussed in the past [1], [3], [9], [10], as shown in Figs.”
BackgroundMethodFault-Tolerant Operation of Multiphase Permanent-Magnet Machines Using Iterative Learning Control
Mohammadpour, A., Mishra, S., & Parsa, L. (2014) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2013.2295537 · Cited by 90
“Extensive research work has been reported on fault-tolerant operation of conventional three-phase motor drives under fault conditions [2], [3].”
BackgroundKumar, V., & Fernandes, B. G. (2017) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2017.2687126 · Cited by 90
Analysis and Experimental Verification of a Fault-Tolerant HEV Powertrain
Song, Y., & Wang, B. (2013) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2013.2245513 · Cited by 81
“Four-leg three-phase faulttolerant inverter topologies do not require available midpoint of dc-link or oversized dc-link capacitors [18], [23], [26]–[29].”
BackgroundFault diagnosis scheme for open‐circuit faults in field‐oriented control induction motor drives
Espinoza‐Trejo, D. R., Campos‐Delgado, D. U., Bossio, G., Bárcenas, E., Hernández‐Díez, J. E., & Lugo‐Cordero, L. F. (2013) · IET Power Electronics · doi:10.1049/iet-pel.2012.0256 · Cited by 78
Fault-Tolerant Inverter for High-Speed Low-Inductance BLDC Drives in Aerospace Applications
Li, H., Li, W., & Ren, H. (2016) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2016.2569611 · Cited by 77
“2569611 failures occurring due to the power switches [7].”
BackgroundMethodHe, J., Katebi, R., Weise, N. D., Demerdash, N. A. O., & Wei, L. (2017) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2017.2665630 · Cited by 77
“of much decreased efficiency due to commutation of many redundant switching devices [7]–[10].”
BackgroundZhao, W., Wu, B., Chen, Q., & Zhu, J. (2018) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2018.2795557 · Cited by 74
A new structure for multilevel inverters with fault-tolerant capability against open circuit faults
Choupan, R., Golshannavaz, S., Nazarpour, D., & Barmala, M. (2018) · Electric Power Systems Research · doi:10.1016/j.epsr.2018.11.013 · Cited by 76
Zhou, X., Sun, J., Li, H., & Song, X. (2018) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2018.2877197 · Cited by 73
“the fault-tolerant methods can be classified as multiphase motor fault-tolerances [7]–[9] and three-phase motor fault-tolerances [10]–[12].”
BackgroundAdding Inverter Fault Detection to Model-Based Predictive Control for Flying-Capacitor Inverters
Druant, J., Vyncke, T. J., Belie, F. D., Sergeant, P., & Melkebeek, J. A. A. (2014) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2014.2354591 · Cited by 72
“This can be a redundant inverter leg [29], but also other more cost-effective topologies are possible depending on the”
BackgroundBhuiyan, E. A., Akhand, M. M. A., Das, S. K., Ali, M. F., Tasneem, Z., Islam, M. R., Saha, D. K., Badal, F. R., Ahamed, M. H., & Moyeen, S. I. (2020) · International Journal of Automation and Computing · doi:10.1007/s11633-020-1250-3 · Cited by 68
Chen, W., Sun, D., Wang, M., & Nian, H. (2020) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2020.3039896 · Cited by 66
Hang, J., Xia, M., Ding, S., Li, Y., Sun, L., & Wang, Q. (2019) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2019.2918683 · Cited by 68
“In [21], the fault leg is replaced by a redundant leg, instead of connecting with the neutral point of the machine, where the performances of the PMSM at postfault operation are”
BackgroundWu, X., Chen, C.-Y., Chen, T., Cheng, S., Mao, Z., Yu, T., & Li, K. (2019) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2019.2941480 · Cited by 63
“of fault-tolerant control strategies [2]–[8] have been proposed to control and prevent the spread of these failures; however, the premise to implement these strategies is the fast fault diagnosis.”
BackgroundFault-Tolerant PMSG Drive With Reduced DC-Link Ratings for Wind Turbine Applications
Freire, N. M. A., & Cardoso, A. J. M. (2014) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2013.2295061 · Cited by 64
Open-Circuit Fault Detection and Diagnosis in Matrix Converters
Brunson, C., Empringham, L., Lillo, L. D., Wheeler, P. W., & Clare, J. (2014) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2014.2364152 · Cited by 61
“Of ten systems will allow continued operation during a fault with less than optimal performance [3].”
BackgroundBramerdorfer, G., Lei, G., Cavagnino, A., Zhang, Y., Sykulski, J. K., & Lowther, D. A. (2020) · IEEE Transactions on Energy Conversion · doi:10.1109/tec.2020.3013190 · Cited by 65
Hwang, J., & Wei, H.-T. (2013) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2013.2275194 · Cited by 60
“For the second type, just like a Y-connected motor, the motor will not be able to operate normally since the neutral point is not connected to the windings [4], [5].”
BackgroundAn improved fault-tolerant control scheme for PWM inverter-fed induction motor-based EVs
Tabbache, B., Benbouzid, M., Kheloui, A., Bourgeot, J., & Mamoune, A. (2013) · ISA Transactions · doi:10.1016/j.isatra.2013.07.004 · Cited by 59
“It is estimated that about 38% of the faults in variable-speed ac drives in industry are due to failures of power devices [1-3] (Fig.”
A Fault-Tolerant Two-Motor Drive With FCS-MP-Based Flux and Torque Control
Lim, C.-S., LEVI, E., Jones, M., Rahim, N. A., & Hew, W.-P. (2014) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2014.2317135 · Cited by 59
“The five-leg configuration provides a similar fault-tolerant property as the addition of a redundant inverter leg, studied in [4], except that the control here is more involved due to the sharing of an inverter leg between the machines.”
BackgroundA Highly Reliable and High-Efficiency Quasi Single-Stage Buck–Boost Inverter
Khan, A. A., Cha, H., Ahmed, H. F., Kim, J.-Y., & Cho, J. (2016) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2016.2598251 · Cited by 57
“1 [1]–[3], [5].”
Majumder, M. G., Yadav, A. K., Gopakumar, K., Krishna Raj, R., Umanand, L., & Franquelo, L. G. (2019) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2019.2898594 · Cited by 57
“These possibilities can be broadly classified into four categories [21]:”
BackgroundFreire, N. M. A., & Cardoso, A. J. M. (2013) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2013.2282935 · Cited by 50
“Various topologies have been proposed to endow a standard threephase converter with fault-tolerant capabilities, by including a redundant leg connected to all the converter phases through TRIACs [4]-[5] or to the machine neutral point [6], and by connecting the midpoint of the dc bus to the converter phases [7]-[8] or…”
BackgroundSong, Z., Ma, X., & Yu, Y. (2019) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2019.2952402 · Cited by 50
“In addition, more control freedoms are simultaneously introduced due to the utilization of dual inverters, which not only enables the multilevel modulation, but also improves the fault-tolerant capability of the drive system [9]–[11].”
BackgroundCurrent Optimization-Based Fault-Tolerant Control of Standard Three-Phase PMSM Drives
Wang, X., Wang, Z., Gu, M., Wang, B., Wang, W., & Cheng, M. (2020) · IEEE Transactions on Energy Conversion · doi:10.1109/tec.2020.3036041 · Cited by 51
“In this way, the open-switch fault is changed to the open-phase fault, and all the fault-tolerant solutions for open-phase fault can be applied [21]–[22].”
BackgroundFault-tolerant operation of an open-end winding five-phase PMSM drive with inverter faults
Meinguet, F., Nguyen, N. K., Sandulescu, P., Kestelyn, X., & Semail, E. (2013) · Annual Conference of the IEEE Industrial Electronics Society (IECON) · doi:10.1109/iecon.2013.6699978 · Cited by 46
“On the other hand, only a few works have addressed the problem of inverter switch short-circuit faults [6], except in topologies with additional components such as fuses and parallel thyristors which are not used in healthy operation [2-5].”
BackgroundFault-Tolerant Capability of Deadbeat-Direct Torque and Flux Control for Three-Phase PMSM Drives
Scarcella, G., Scelba, G., Pulvirenti, M., & Lorenz, R. D. (2017) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2017.2743070 · Cited by 47
“Some power converter topologies are able to tolerate a single open/short circuit of power devices and an open circuit of the machine phases [12], [20], [22].”
BackgroundFault-Tolerant AC Multidrive System
Pulvirenti, M., Scarcella, G., Scelba, G., Cacciato, M., & Testa, A. (2014) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2013.2292861 · Cited by 46
Moraes, T. J. D. S., Nguyen, N. K., Semail, E., Meinguet, F., & Guerin, M. (2017) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2017.2671907 · Cited by 42
“However, it usually increases the cost and the weight of the system as well [4], [5], [11]–[13].”
BackgroundAn Embedded Fault-Tolerant Control Method for Single Open-Switch Faults in Standard PMSM Drives
Zhang, Z., Hu, Y., Luo, G., Gong, C., Liu, X., & Chen, S. (2022) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2022.3146216 · Cited by 42
“PMSM drive is limited compared to complex topologies, such as four-leg inverters [1], [2], paralleled inverters [3], [4], and multilevel inverters [5], [6].”
BackgroundAn Enhanced Fault-Tolerant and Autoreconfigurable BLDC Motor Drive for Electric Vehicle Applications
Kumar, P. H., & Somasekhar, V. T. (2022) · IEEE Journal of Emerging and Selected Topics in Industrial Electronics · doi:10.1109/jestie.2022.3196818 · Cited by 39
“In the research article presented in [28], a single-switch OC (or) SC fault-tolerant drive topology for EV applications is described, which uses six TRIACs and one actuator leg additionally.”
MethodFault diagnosis of in-wheel BLDC motor drive for electric vehicle application
Abkenar, A. T., & Ektesabi, M. (2013) · IEEE Intelligent Vehicles Symposium · doi:10.1109/ivs.2013.6629585 · Cited by 38
“The proposed VSI model in [12] is recommended for BLDC motors.”
MethodKong, W., Kang, M., Li, D., Qu, R., Jiang, D., & Gan, C. (2017) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2017.2737027 · Cited by 37
“tinue torque-ripple free operation [13], [14].”
Shahin, A., Martin, J., & Pierfederici, S. (2018) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2018.2854226 · Cited by 37
Multi‐resolution analysis for converter switch faults identification
Keswani, R. A., Suryawanshi, H. M., & Ballal, M. S. (2015) · IET Power Electronics · doi:10.1049/iet-pel.2014.0450 · Cited by 36
A Fault-Tolerant Five-Level Inverter Topology With Reduced Component Count for OEIM Drives
Majumder, M. G., Rakesh, R., Gopakumar, K., Umanand, L., Al‐Haddad, K., & Jarzyna, W. (2020) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2020.2972056 · Cited by 35
“These faults in power switches can be categorized as [22]: 1) single-switch short-circuit fault; 2) single-switch open-circuit fault; 3) phase leg short-circuit fault; and 4) phase leg open-circuit fault.”
BackgroundChen, T., Pan, Y., & Xiong, Z. (2020) · Electronics · doi:10.3390/electronics9081251 · Cited by 35
Current sensors fault detection and tolerant control strategy for three-phase induction motor drives
Azzoug, Y., Sahraoui, M., Pusca, R., Ameid, T., Romary, R., & Cardoso, A. J. M. (2020) · Electrical Engineering · doi:10.1007/s00202-020-01120-5 · Cited by 36
Detection of Two-Level Inverter Open-Circuit Fault Using a Combined DWT-NN Approach
Chérif, B. D. E., & Bendiabdellah, A. (2018) · Journal of Control Science and Engineering · doi:10.1155/2018/1976836 · Cited by 34
“rotary machines and static converter for fault diagnosis and it particularly matches well for the nonstationary signals [12, 13].”
BackgroundSudha, V., Vijayarekha, K., Kumar, S. R., & Prabaharan, N. (2022) · IEEE Access · doi:10.1109/access.2022.3193784 · Cited by 34
“Continuous operation of CHBMLI under such failure conditions leads to additional failures and causes serious effects [12].”
BackgroundEstima, J. O., & Cardoso, A. J. M. (2012) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce.2012.6342310 · Cited by 33
“In [11]-[14], a similar fault-tolerant converter topology is reported, where the machine phase is isolated from the faulty inverter leg and connected through a TRIAC to an extra inverter leg, used as hardware redundancy.”
MethodFull-Bridge Single-Inductor-Based Buck–Boost Inverters
Khan, U. A., & Park, J.-W. (2020) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2020.3011462 · Cited by 31
“3, where the buck dc–dc converter provides a buck operation, and the CSI provides a boost operation.”
BackgroundInfluentialYang, J., Jiang, D., Sun, H., Ding, J., Li, A., & Liu, Z. (2021) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2021.3100983 · Cited by 32
“Many scholars have studied the corresponding fault detection and fault tolerance methods for various power electronic systems, such as modular multilevel converters system [17], voltage-source inverters feeding ac motors [18], and voltage source inverter for permanent magnet drives [19].”
BackgroundFan, Y. J., Zhu, W., Zhang, X., Cheng, M., & Chau, K. T. (2015) · IEEE Transactions on Energy Conversion · doi:10.1109/tec.2015.2498613 · Cited by 31
“In [10] and [11], a redundant leg is added to a standard two-level threeleg inverter to replace the faulted leg.”
BackgroundCurrent observer-based online open-switch fault diagnosis for voltage-source inverter
Chen, Y., Zhang, J.-J., & Chen, Z.-Y. (2019) · ISA Transactions · doi:10.1016/j.isatra.2019.09.019 · Cited by 34
Fault detection and fault-tolerant control of power converter fed PMSM
Moujahed, M., Azza, H. B., Frifita, K., Jemli, M., & Boussak, M. (2015) · Electrical Engineering · doi:10.1007/s00202-015-0350-5 · Cited by 30
Rangari, S. C., Suryawanshi, H. M., & Renge, M. M. (2018) · Electronics · doi:10.3390/electronics7090159 · Cited by 30
Zhou, D., Zhao, J., & Liu, Y. (2016) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2016.2581761 · Cited by 29
“Modular parallel redundant systems [1], [2] or systems with phase numbers higher than three [3], [4] have received considerable attention to keep the continuous operation.”
BackgroundSikora, A., Zielonka, A., & Woźniak, M. (2022) · Sensors · doi:10.3390/s22031058 · Cited by 28
“In particular, the construction of the electronic commutator is interesting [2].”
BackgroundSingle-Stage Single-Phase H6 and H8 Non-Isolated Buck-Boost Photovoltaic Inverters
Khan, U. A., Khan, A. A., Akbar, F., & Park, J.-W. (2022) · IEEE Journal of Emerging and Selected Topics in Power Electronics · doi:10.1109/jestpe.2022.3153840 · Cited by 28
Self-Adaptive Fault-Tolerant Control of Three-Phase Series-End Winding Motor Drive
Sun, X., Liu, Z., Li, A., Wang, Z., Jiang, D., & Qu, R. (2022) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2022.3160747 · Cited by 28
“windings, the maximum fault-tolerant output power might be decreased considering voltage and current limits of the inverter, unless the alternate bridge is implemented to ensure the unchanged drive structure before and after the faults [8].”
BackgroundShort-circuit switches fault analysis of voltage source inverter using spectrogram
Abdullah, A. R., Ahmad, N. S., Bahari, N., Manap, M., Jidin, A., & Jopri, M. H. (2013) · International Conference on Electrical Machines and Systems (ICEMS) · doi:10.1109/icems.2013.6713294 · Cited by 28
Zhu, Z. Q., Pothi, N., Xu, P., & Ren, Y. (2019) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2019.2909492 · Cited by 28
Fault-Tolerant SRM Drives—A Review
Ali, N., & Narimani, M. (2024) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2024.3392713 · Cited by 30
Dieterle, O., Greiner, T., & Heidrich, P. (2019) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2018.2835422 · Cited by 25
“Different options are listed in [2]–[4].”
Fard, M. T., He, J., & Wang, Z. (2020) · IEEE Transportation Electrification Conference and Expo · doi:10.1109/itec48692.2020.9161725 · Cited by 25
Catuogno, G. R., García, G. O., & Leidhold, R. (2015) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2015.2438771 · Cited by 26
“For instance, in [18], a 4wEL topology with one redundant leg is proposed,”
BackgroundKwon, S., & Ha, J.-I. (2019) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2019.2906431 · Cited by 26
“In another approach, the 4-leg inverter was proposed that includes a redundant leg and an external wire connected to the neutral point of the motor [36].”
BackgroundAhmad, A., Anas, M., Sarwar, A., Zaid, M., Tariq, M., Ahmad, J., & Beig, A. R. (2020) · Energies · doi:10.3390/en13071556 · Cited by 25
“The proposed topology was better as compared to topology proposed by the authors in [4,5] concerning the number of DC sources.”
ResultImpact of Current Pulsation on BLDC Motor Parameters
Sikora, A., & Woźniak, M. (2021) · Sensors · doi:10.3390/s21020587 · Cited by 24
“Powering the excitation winding (used in earlier designs) generated electricity losses resulting from the flow of the excitation current of the electric machine [6,7].”
BackgroundFault Tolerant Control of Advanced Power Generation Center for More-Electric Aircraft Applications
Lang, X., Yang, T., Wang, Z., Wang, C., Bozhko, S. V., & Wheeler, P. W. (2021) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2021.3093506 · Cited by 24
“In order to achieve the same control performance as in a healthy state, a redundant phase leg is deployed to replace the faulty phase leg hence a healthy three-phase rectifier can be reconstructed [20], [21].”
BackgroundLee, S., Chen, F., Jahns, T. M., & Sarlioglu, B. (2021) · IEEE International Symposium on Diagnostics for Electrical Machines, Power Electronics and Drives (SDEMPED) · doi:10.1109/sdemped51010.2021.9605513 · Cited by 25
Xia, C., Qiu, X., Wang, Z., & Shi, T. (2016) · IET Electric Power Applications · doi:10.1049/iet-epa.2015.0310 · Cited by 23
Aleem, Z., Winberg, S. L., Iqbal, A., Al-Hitmi, M. A. E., & Hanif, M. (2019) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2018.2889615 · Cited by 23
“Therefore, these power inverters need additional dc–dc converters to provide buck/boost functionality, which increases the cost, makes systems larger, and requires more complex control mechanisms—together these aspects reduce the efficiency of conventional VSIs and CSIs [1].”
BackgroundBaghli, M., Delpha, C., Diallo, D., Hallouche, A., Mba, D., & Wang, T. (2019) · Energies · doi:10.3390/en12071372 · Cited by 23
“In industrial applications using variable-speed AC drives, different studies have proved that about 38% of the faults are due to failures in the power device [11].”
BackgroundMohammadi, F., & Saif, M. (2023) · IEEE Access · doi:10.1109/access.2023.3339549 · Cited by 22
“In this regard, various fault-tolerant control approaches are presented in the literature [17], [18], [19], [20], [21] aiming at fast fault diagnosis.”
BackgroundPWM inverter-fed induction motor-based electrical vehicles fault-tolerant control
Tabbache, B., Benbouzid, M., Kheloui, A., Bourgeot, J., & Mamoune, A. (2013) · Annual Conference of the IEEE Industrial Electronics Society (IECON) · doi:10.1109/iecon.2013.6700506 · Cited by 21
“It is estimated that about 38% of the faults in variable-speed ac drives in industry are due to failures of power devices [1-3].”
BackgroundReliable DC Shipboard Power Systems—Design, Assessment, and Improvement
van der Sande, R., Shekhar, A., & Bauer, P. (2025) · IEEE Open Journal of the Industrial Electronics Society · doi:10.1109/ojies.2025.3532095 · Cited by 21
“An example of this is provided in [127], where the Errabelli and Mutschler [127] proposed the use of a redundant phase-leg that can recoup the inverter functionality after a single-leg failure.”
Nadh, G., & Arun Rahul, S. (2022) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2022.3199193 · Cited by 19
“Hence, PWM-4 can be used in case of switch short-circuit fault [30] in switches 1Y and 2B′ or switch open-circuit fault in switches 1Y ′ and 2B, as shown in Fig.”
BackgroundResearch on fault analysis and fault-tolerant control of EV/HEV powertrain
Tabbache, B., Kheloui, A., Benbouzid, M., Mamoune, A., & Diallo, D. (2014) · International Conference on Green Energy (ICGE) · doi:10.1109/icge.2014.6835436 · Cited by 21
Metadata
- Authors
- Errabelli, R. R., & Mutschler, P.
- Affiliations
- Technische Universität Darmstadt (DE)
- Venue
- IEEE Transactions on Power Electronics
- Published
- 2012-02
- Volume
- 27
- Issue
- 2
- Pages
- 500-508
- ISSN
- 0885-8993 (ISSN-L)
- 1941-0107
- OpenAlex
- W2079590925
- Cited by
- 278
- References
- 19
- Citations by year
- 2026: 5 · 2025: 6 · 2024: 10 · 2023: 10 · 2022: 17 · 2021: 25 · 2020: 19 · 2019: 23 · 2018: 25 · 2017: 25 · 2016: 22 · 2015: 23 · 2014: 29 · 2013: 24 · 2012: 13
- FWCI
- 15.23
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- IEEE Transactions on Power Electronics (publishedVersion)
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Multilevel Inverters and Converters
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Electric Motor Design and Analysis
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Sensorless Control of Electric Motors
- Keywords
- fault-tolerant inverter, voltage source inverter, permanent magnet synchronous motor, short-circuit faults, open-circuit fault, field-oriented control
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.