The DOI matches its Crossref record; 32 of the 32 references it cites were found in a registry or an index.
A New Approach to Fault Diagnostics for Permanent Magnet Synchronous Machines Using Electromagnetic Signature Analysis
Abstract
This paper proposes a novel approach to health monitoring and multifault detection in permanent magnet synchronous machines using direct flux measurement with search coils. Unlike other spectrum-based fault detection schemes, only the fundamental frequency component of the measured voltage is utilized for fault detection. Therefore, the performance of the proposed scheme is not affected by nonstationary speed or harmonics introduced by the power supply. In addition, location of interturn short circuits and direction of static eccentricity can be detected, which have never been done by any other scheme. In spite of the invasive nature of the technique, it is very suitable for mission-critical applications and emerging applications such as off-shore wind turbines, hybrid vehicle technology, and military applications, where early detection of faults is of paramount importance. 2-D simulations using finite element analysis have been presented to validate the proposed method under different operating conditions. Experimental introduction of stator interturn short circuit, demagnetization, and static eccentricity has been discussed, and the proposed scheme is experimentally implemented to examine its effectiveness.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The flux-based method requires search coils mounted inside the motor and thus is a highly invasive method.
“However, the flux-based method requires search coils mounted inside the motor [91] and thus is a highly invasive method.”
From Fault Diagnosis and Fault-Tolerant Control of PMSM Drives–State of the Art and Future Challenges (2022) · cites this paper as [91]
Citations
Cites
Motor bearing damage detection using stator current monitoring
Schoen, R. R., Habetler, T. G., Kamran, F., & Bartfield, R. G. (1995) · IEEE Transactions on Industry Applications · doi:10.1109/28.475697 · Cited by 761
Motor bearing damage detection using stator current monitoring
Schoen, R. R., Habetler, T. G., Kamran, F., & Bartheld, R. G. (2002) · IEEE Industry Applications Society Annual Meeting (IAS) · doi:10.1109/ias.1994.345491 · Cited by 638
The detection of inter-turn short circuits in the stator windings of operating motors
Joksimović, G., & Penman, J. (2000) · IEEE Transactions on Industrial Electronics · doi:10.1109/41.873216 · Cited by 473
Detection and location of interturn short circuits in the stator windings of operating motors
Penman, J., Sedding, H. G., Lloyd, B. A., & Fink, W. T. (1994) · IEEE Transactions on Energy Conversion · doi:10.1109/60.368345 · Cited by 394
Static-, Dynamic-, and Mixed-Eccentricity Fault Diagnoses in Permanent-Magnet Synchronous Motors
Ebrahimi, B. M., Faiz, J., & Roshtkhari, M. J. (2009) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2009.2029577 · Cited by 387
A new approach to on-line turn fault detection in AC motors
Kliman, G. B., Premerlani, W. J., Koegl, R. A., & Hoeweler, D. (2002) · IEEE Industry Applications Society Annual Meeting (IAS) · doi:10.1109/ias.1996.557113 · Cited by 303
Detecting Rotor Faults in Low Power Permanent Magnet Synchronous Machines
le Roux, W., Harley, R. G., & Habetler, T. G. (2007) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2006.886620 · Cited by 274
Espinosa, A. G., Rosero, J. A., Cusido, J., Romeral, L., & Ortega, J. A. (2010) · IEEE Transactions on Energy Conversion · doi:10.1109/tec.2009.2037922 · Cited by 243
Ruiz, J.-R. R., García, J. R., Espinosa, A. G., & Romeral, L. (2009) · IEEE Transactions on Magnetics · doi:10.1109/tmag.2009.2015942 · Cited by 231
Ebrahimi, B. M., & Faiz, J. (2010) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2010.2050496 · Cited by 209
Urresty, J.-C., Riba, J.-R., Delgado, M., & Romeral, L. (2012) · IEEE Transactions on Energy Conversion · doi:10.1109/tec.2011.2176127 · Cited by 181
Liu, X.-Q., Zhang, H., Liu, J., & Yang, J. (2000) · IEEE Transactions on Industrial Electronics · doi:10.1109/41.873210 · Cited by 180
Rajagopalan, S., Roux, W. L., Habetler, T. G., & Harley, R. G. (2007) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2007.904183 · Cited by 164
Insulation failure prediction in AC machines using line-neutral voltages
Cash, M. A., Habetler, T. G., & Kliman, G. B. (1998) · IEEE Transactions on Industry Applications · doi:10.1109/28.738983 · Cited by 149
Characterization of Noise and Vibration Sources in Interior Permanent-Magnet Brushless DC Motors
Ko, H.-S., & Kim, K.-J. (2004) · IEEE Transactions on Magnetics · doi:10.1109/tmag.2004.832991 · Cited by 141
Shah, D. U., Nandi, S., & Neti, P. (2009) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2009.2027406 · Cited by 125
Condition monitoring of electrical drives
Penman, J., Dey, M. N., Tait, A. J., et al. (1986) · IEE Proceedings B Electric Power Applications · doi:10.1049/ip-b.1986.0019 · Cited by 125
Kral, C., Habetler, T. G., & Harley, R. G. (2004) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2004.830762 · Cited by 114
An on-line method to detect incipient failure of turn insulation in random-wound motors
Sottile, J., & Kohler, J. L. (1993) · IEEE Transactions on Energy Conversion · doi:10.1109/60.260992 · Cited by 112
Alternatives for assessing the electrical integrity of induction motors
Kohler, J. L., Sottile, J., & Trutt, F. C. (1992) · IEEE Transactions on Industry Applications · doi:10.1109/28.158836 · Cited by 108
Neti, P., & Nandi, S. (2009) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2009.2018905 · Cited by 104
Hong, J., Lee, S. B., Kral, C., & Haumer, A. (2011) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2011.2176145 · Cited by 103
Automated Monitoring of Magnet Quality for Permanent-Magnet Synchronous Motors at Standstill
Hong, J., Hyun, D., Lee, S. B., Yoo, J.-Y., & Lee, K. (2010) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2010.2049811 · Cited by 100
Farooq, J. A., Srairi, S., Djerdir, A., & Miraoui, A. (2006) · IEEE Transactions on Magnetics · doi:10.1109/tmag.2006.870936 · Cited by 94
Detection of Induction Motor Faults in Inverter Drives Using Inverter Input Current Analysis
Georgakopoulos, I. P., Mitronikas, E. D., & Safacas, A. N. (2010) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2010.2093476 · Cited by 89
Yoon, T. (2005) · IEEE Transactions on Magnetics · doi:10.1109/tmag.2005.848321 · Cited by 59
The Noise and Vibration Analysis of BLDC Motor Due to Asymmetrical Permanent-Magnet Overhang Effects
Kang, G.-H., Son, Y.-D., & Kim, G.-T. (2008) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2008.2002278 · Cited by 31
Yang, W., Tavner, P. J., & Wilkinson, M. (2008) · IET International Conference on Power Electronics, Machines and Drives (PEMD) · doi:10.1049/cp:20080473 · Cited by 28
Advanced fault diagnosis for the mass production of small-power electric motors
Filbert, D. (1993) · Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE · doi:10.1117/12.156288 · Cited by 8
Automated monitoring of magnet quality for permanent magnet synchronous motors at standstill
Hong, J., Hyun, D., Lee, S. B., Yoo, J., & Lee, K. (2009) · IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce.2009.5316464 · Cited by 6
Parameter Estimation and Residual Analysis A Comparison
Schneider, C., & Filbert, D. (1994) · IFAC Proceedings Volumes · doi:10.1016/s1474-6670(17)48107-9 · Cited by 5
Intelligent measurement methods in technical diagnosis and quality assurance - a comparison
Filbert, D. (1988) · Measurement · doi:10.1016/0263-2241(88)90005-x · Cited by 4
Flagged first, then by citations
Research works printed but not linked: 1
- leonhard, 1986, Vibration and stray flux monitoring for unbalanced supply and inter-turn winding fault diagnosis in induction machines, Br J Non-Destr Test, 28, 211
Cited by
Sorted by citations
Fault Diagnosis and Fault-Tolerant Control of PMSM Drives–State of the Art and Future Challenges
Orlowska-Kowalska, T., Wolkiewicz, M., Pietrzak, P., Skowron, M., Ewert, P., Tarchala, G., Krzysztofiak, M., & Kowalski, C. T. (2022) · IEEE Access · doi:10.1109/access.2022.3180153 · Cited by 328
“[91]-[93] Axial flux FFT PDF, UDF, ON, HS, NAOF SC, INV or ACR”
BackgroundMethodFaiz, J., & Mazaheri-Tehrani, E. (2017) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2016.2608950 · Cited by 207
Choi, S., Haque, M. S., Tarek, M. T. B., Mulpuri, V., Duan, Y., Das, S., Garg, V., Ionel, D. M., Masrur, M. A., Mirafzal, B., et al. (2018) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2018.2819627 · Cited by 192
Haddad, R. Z., & Strangas, E. G. (2016) · IEEE Transactions on Energy Conversion · doi:10.1109/tec.2016.2558183 · Cited by 158
Moosavi, S. S., Djerdir, A., Amirat, Y. A., & Khaburi, D. A. (2015) · Journal of Magnetism and Magnetic Materials · doi:10.1016/j.jmmm.2015.04.062 · Cited by 96
Comprehensive review on inter‐turn fault indexes in permanent magnet motors
Faiz, J., Nejadi‐Koti, H., & Valipour, Z. (2017) · IET Electric Power Applications · doi:10.1049/iet-epa.2016.0196 · Cited by 86
Bhuiyan, E. A., Akhand, M. M. A., Das, S. K., Ali, M. F., Tasneem, Z., Islam, M. R., Saha, D. K., Badal, F. R., Ahamed, M. H., & Moyeen, S. I. (2020) · International Journal of Automation and Computing · doi:10.1007/s11633-020-1250-3 · Cited by 68
Improved ZSVC‐based fault detection technique for incipient stage inter‐turn fault in PMSM
Fang, J., Sun, Y., Wang, Y., Wei, B., & Hang, J. (2019) · IET Electric Power Applications · doi:10.1049/iet-epa.2019.0016 · Cited by 30
A Novel Fault Diagnosis Technique for IPMSM Using Voltage Angle
Ullah, Z., Lee, S.-T., & Hur, J. (2018) · 2018 IEEE Energy Conversion Congress and Exposition (ECCE) · doi:10.1109/ecce.2018.8557375 · Cited by 13
Metadata
- Authors
- Da, Y., Shi, X., & Krishnamurthy, M.
- Affiliations
- Mercedes-Benz Research and Development North America (United States) (US)
- Illinois Institute of Technology (US)
- Venue
- IEEE Transactions on Power Electronics
- Published
- 2013-08
- Volume
- 28
- Issue
- 8
- Pages
- 4104-4112
- ISSN
- 0885-8993 (ISSN-L)
- 1941-0107
- OpenAlex
- W1977202657
- Cited by
- 303
- References
- 32
- Citations by year
- 2026: 9 · 2025: 21 · 2024: 35 · 2023: 39 · 2022: 37 · 2021: 22 · 2020: 18 · 2019: 32 · 2018: 22 · 2017: 15 · 2016: 15 · 2015: 12 · 2014: 17 · 2013: 8
- FWCI
- 17.63
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- IEEE Transactions on Power Electronics (publishedVersion)
- Topics
- Physical Sciences › Engineering › Control and Systems Engineering › Machine Fault Diagnosis Techniques
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Electric Motor Design and Analysis
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Sensorless Control of Electric Motors
- Keywords
- permanent magnet synchronous motor, fault diagnosis, search coil, static eccentricity, demagnetization, health monitoring
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
