Review of Die-Attach Materials for SiC High-Temperature Packaging
The DOI matches its Crossref record; 116 of the 116 references it cites were found in a registry or an index.
Abstract
Silicon carbide (SiC) devices have shown definite advantages over Si counterparts in high-temperature, high-voltage, and high-frequency applications. To fully exploit the potentiality of SiC devices in high temperatures, die-attach materials that can withstand high temperatures for a long time are required in the power electronics packaging. In this article, the high-temperature die-attach materials, such as high-temperature solders and transient liquid-phase bonding materials, were reviewed first. Then, metallic (mainly Ag and Cu) nanoparticles (NPs) sintering technologies were thoroughly overviewed. The metallic NPs sintering materials, metallic NPs sintering process, and interface and reliability were analyzed, respectively. Finally, the challenges and outlook of promising Cu NPs sintering technology were discussed.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“IMC growth is often accelerated by microstructural defects at the solder interface (e.g., grain boundaries, oxides, interfacial roughness), which act as heterogeneous nucleation sites; in addition, unbalanced Cu/Sn interdiffusion can induce Kirkendall voiding, degrading thermo-mechanical integrity over life [30,32].”
From Thermal Management of Wide-Bandgap Power Semiconductors: Strategies and Challenges in SiC and GaN Power Devices (2025) · cites this paper as [30]
In the citing paper
“IMC growth is often accelerated by microstructural defects at the solder interface (e.g., grain boundaries, oxides, interfacial roughness), which act as heterogeneous nucleation sites; in addition, unbalanced Cu/Sn interdiffusion can induce Kirkendall voiding, degrading thermo-mechanical integrity over life [30,32].”
From Thermal Management of Wide-Bandgap Power Semiconductors: Strategies and Challenges in SiC and GaN Power Devices (2025) · cites this paper as [30]
In the citing paper
“Traditional Sn-based solders are constrained by relatively low melting points and intermetallic compound (IMC) formation [30], motivating highreliability alternatives [31].”
From Thermal Management of Wide-Bandgap Power Semiconductors: Strategies and Challenges in SiC and GaN Power Devices (2025) · cites this paper as [30]
In the citing paper
“Silver-sintered joints provide excellent electrical/thermal conductivity and high-temperature stability but face electromigration (EM) and cost challenges [2,30-35].”
From Thermal Management of Wide-Bandgap Power Semiconductors: Strategies and Challenges in SiC and GaN Power Devices (2025) · cites this paper as [30]
In the citing paper
“In parallel, silver and copper microparticle sintering and transient liquid-phase bonding are recognized as reliable assembly approaches that combine excellent electrical/thermal conductivity with high-temperature stability [2,3,30] (Figure 2).”
From Thermal Management of Wide-Bandgap Power Semiconductors: Strategies and Challenges in SiC and GaN Power Devices (2025) · cites this paper as [30]
1 more claim about this paper
Create a free account to see every claim other papers make about this one.
Citations
Cites
A Survey of Wide Bandgap Power Semiconductor Devices
Millán, J., Godignon, P., Perpiñà, X., Pérez-Tomás, A., & Rebollo, J. (2014) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2013.2268900 · Cited by 2,685
Sintering: Densification, Grain Growth and Microstructure
Kang, S. L. (2005) · Cited by 1,006
Metal–metal bonding process using Ag metallo-organic nanoparticles
Ide, E., Angata, S., Hirose, A., & Kobayashi, K. F. (2005) · Acta Materialia · doi:10.1016/j.actamat.2005.01.047 · Cited by 500 · cited 2×
“In addition, the sintering temperature, sintering time, and other parameters of Cu NPs paste can be determined by material characterization experiments, e.g., thermogravimetric analysis (TGA), elevated-temperature X-ray diffraction (XRD), and differential scanning calorimetry [55], [66], [85], [88].”
BackgroundMethodDie Attach Materials for High Temperature Applications: A Review
Manikam, V. R., & Cheong, K. Y. (2011) · IEEE Transactions on Components, Packaging and Manufacturing Technology · doi:10.1109/tcpmt.2010.2100432 · Cited by 478 · cited 2×
“Therefore, sintering materials can effectively leverage the performance of SiC devices [8].”
BackgroundSize-dependent melting point depression of nanostructures: Nanocalorimetric measurements
Zhang, M., Efremov, M. Y., Schiettekatte, F., Olson, E. A., Kwan, A. T., Lai, S. L., Wisleder, T., Greene, J. E., & Allen, L. H. (2000) · Physical Review B · doi:10.1103/physrevb.62.10548 · Cited by 464 · cited 1×
“When materials are reduced down to the nanoscale, several material characteristics, e.g., melting point [34], surface energy [35], and diffusion coefficient [36], exhibit significant changes compared with their bulk counterparts.”
BackgroundCopper Nanoparticles for Printed Electronics: Routes Towards Achieving Oxidation Stability
Magdassi, S., Grouchko, M., & Kamyshny, A. (2010) · Materials · doi:10.3390/ma3094626 · Cited by 429
Mechanical properties of nano-silver joints as die attach materials
Siow, K. S. (2012) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2011.10.092 · Cited by 390 · cited 1×
“The release involves two fundamental steps: the separation of the organic shells, which depends on their binding energy to the metallic NPs, and the evaporation of the shells, which is related to their inherent boiling point [58], [59].”
BackgroundBai, J. G., Zhang, Z. Z., Calata, J. N., & Lu, G.-Q. (2006) · IEEE Transactions on Components and Packaging Technologies · doi:10.1109/tcapt.2005.853167 · Cited by 375
Nanoparticles by Laser Ablation
Semaltianos, N. G. (2010) · Critical Reviews in Solid State and Materials Sciences · doi:10.1080/10408431003788233 · Cited by 338 · cited 3×
“Laser ablation is primarily controlled by the pulsewidth or pulse duration [53].”
BackgroundDensification and grain growth during sintering of nanosized particles
Fang, Z. Z., & Wang, H. (2008) · International Materials Reviews · doi:10.1179/174328008x353538 · Cited by 332
Cited by
Reliability Challenges, Models, and Physics of Silicon Carbide and Gallium Nitride Power Devices
Avraham, T., Dhyani, M., & Bernstein, J. B. (2025) · Energies · doi:10.3390/en18051046 · Cited by 42
Han, G., Kim, J., Park, S., & Bae, W. (2025) · Electronics · doi:10.3390/electronics14214193 · Cited by 34
“Silver-sintered joints provide excellent electrical/thermal conductivity and high-temperature stability but face electromigration (EM) and cost challenges [2,30–35].”
The Overview of Silicon Carbide Technology: Status, Challenges, Key Drivers, and Product Roadmap
Kamiński, M., Król, K., Kwietniewski, N., Myśliwiec, M., Sochacki, M., Stonio, B., Kisiel, R., Martychowiec, A., Racka, K., Werbowy, A., et al. (2024) · Materials · doi:10.3390/ma18010012 · Cited by 34
“In this case, the bonding layer is a film of intermetallic compounds (IMCs) whose thermal conductivity is in the range of 30–60 W/mK [160].”
Review of Inorganic Nonmetallic Materials in Power Electronics Packaging Application
Chen, J., Tian, T., Gu, C., Zeng, H., Hou, F., Zhang, G., & Fan, J. (2025) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2025.3550882 · Cited by 27
“Metals, with their excellent electrical conductivity, play a crucial role in internal electrical interconnections, such as die attach materials, wire bonding, and gold stud bumps used for interconnections [21], [22], [23], [24], [25], [26].”
Self-citationCopper-based composite sintering materials and reliability analysis for power electronics packaging
Wang, X., Yang, Z., Bian, L., Liu, W., Zhang, G., Zhang, J., Chen, C., & Liu, P. (2025) · Journal of Science Advanced Materials and Devices · doi:10.1016/j.jsamd.2025.100963 · Cited by 11
Self-citation
Metadata
- Authors
- Hou, F., Sun, Z., Su, M., Fan, J., You, X., Li, J., Wang, Q., Cao, L., & Zhang, G.
- Affiliations
- Chinese Academy of Sciences (CN)
- Fudan University (CN)
- Delft University of Technology (NL)
- Venue
- IEEE Transactions on Power Electronics
- Published
- 2024-10
- Volume
- 39
- Issue
- 10
- Pages
- 13471-13486
- ISSN
- 0885-8993 (ISSN-L)
- 1941-0107
- OpenAlex
- W4399881110
- Cited by
- 52
- References
- 116
- Citations by year
- 2026: 23 · 2025: 27 · 2024: 2
- FWCI
- 5.39
- Type
- journal article
- Language
- en
- Open access
- closed
- Licence
- Locations
- IEEE Transactions on Power Electronics (publishedVersion)
- Funders
- National Natural Science Foundation of China (62174177)
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Electronic Packaging and Soldering Technologies
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Silicon Carbide Semiconductor Technologies
- Physical Sciences › Engineering › Electrical and Electronic Engineering › 3D IC and TSV technologies
- Keywords
- silicon carbide, die attach materials, high-temperature packaging, high-temperature solder, transient liquid phase bonding, metal nanoparticles, silver nanoparticles, copper nanoparticles, sintering, power electronics packaging, interface reliability
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Review of Die-Attach Materials for SiC High-Temperature Packaging. https://app.cochat.ai/papers/10.1109/tpel.2024.3417529
- The paper
- Hou, F., Sun, Z., Su, M., Fan, J., You, X., Li, J., Wang, Q., Cao, L., & Zhang, G. (2024). Review of Die-Attach Materials for SiC High-Temperature Packaging. IEEE Transactions on Power Electronics. https://doi.org/10.1109/tpel.2024.3417529
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.