Numerical Investigations on the Ultrasonic Atomization of Catalyst Inks for Proton Exchange Membrane Fuel Cells
The DOI matches its Crossref record; 71 of the 71 references it cites were found in a registry or an index.
Abstract
In the fabrication of a proton exchange membrane fuel cell electrode, the catalyst layers (CLs) are coated onto either a gas diffusion medium or a membrane. The deposition method of the catalyst ink plays an important role in the structure of the CL, which directly affects its electrochemical performance. Ultrasonic spraying is a method commonly employed for depositing catalyst ink onto the membrane, and the consequent droplet size is correlated to the microstructure of the CLs. In this study, a two-dimensional nozzle model that vibrates at an ultrasonic frequency was developed to simulate the spraying process of the catalyst ink. The volume of the fluid method with dynamic meshing was used. Parametric studies were carried out to gain insights into the atomization process. It was found that measures such as increasing the nozzle amplitude and frequency, and selecting the surface tension and viscosity of the catalyst ink within a proper range, are conducive to obtaining finer droplets and narrower droplet size distribution. Simulation results of non-Newtonian fluids with different viscosity ranges show that the ink fluid with higher viscosity and low shear rate improves the spray quality. This observation is consistent with the results of Newtonian fluids with different viscosities.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“When the viscosity is lower than a certain critical value (e.g., 15 mPa•s [68]), increasing the viscosity of ink will decrease the number of large droplets and increase the uniformity of the formed droplets, enhancing spraying quality.”
From Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells (2022) · cites this paper as [68]
In the citing paper
“through a spray nozzle, a high shear environment (the shear rate at the ink film is ca. 10 4 -10 6 s -1 in the spraying process [68])”
From Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells (2022) · cites this paper as [68]
In the citing paper
“During the spraying process, the surface tension of the ink could impact the spray quality to some extent by affecting the small droplets [68].”
From Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells (2022) · cites this paper as [68]
Citations
Cites
NIH Image to ImageJ: 25 years of image analysis
Schneider, C. A., Rasband, W. S., & Eliceiri, K. W. (2012) · Nature Methods · doi:10.1038/nmeth.2089 · Cited by 64,638
Volume of fluid (VOF) method for the dynamics of free boundaries
Hirt, C. W., & Nichols, B. D. (1981) · Journal of Computational Physics · doi:10.1016/0021-9991(81)90145-5 · Cited by 16,105
Polymer Electrolyte Fuel Cell Model
Springer, T. E., Zawodzinski, T. A., & Gottesfeld, S. (1991) · Journal of The Electrochemical Society · doi:10.1149/1.2085971 · Cited by 3,528
An overview of fuel cell technology: Fundamentals and applications
Sharaf, O. Z., & Orhan, M. F. (2014) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2014.01.012 · Cited by 1,859
Litster, S., & McLean, G. (2004) · Journal of Power Sources · doi:10.1016/j.jpowsour.2003.12.055 · Cited by 1,275
Kongkanand, A., & Mathias, M. F. (2016) · The Journal of Physical Chemistry Letters · doi:10.1021/acs.jpclett.6b00216 · Cited by 1,202
Ultrasonic Atomization of Liquids
Lang, R. J. (1962) · The Journal of the Acoustical Society of America · doi:10.1121/1.1909020 · Cited by 892
Applications of proton exchange membrane fuel cell systems
Wee, J.-H. (2007) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2006.01.005 · Cited by 699
Review—Electromobility: Batteries or Fuel Cells?
Gröger, O., Gasteiger, H. A., & Suchsland, J.-P. (2015) · Journal of The Electrochemical Society · doi:10.1149/2.0211514jes · Cited by 529
Imaging the Microscopic Structure of Shear Thinning and Thickening Colloidal Suspensions
Cheng, X., McCoy, J. H., Israelachvili, J. N., & Cohen, I. (2011) · Science · doi:10.1126/science.1207032 · Cited by 524
A Historical Perspective of Fuel Cell Technology in the 20th Century
Perry, M. L., & Fuller, T. F. (2002) · Journal of The Electrochemical Society · doi:10.1149/1.1488651 · Cited by 491
Fuel Cell Catalyst Layers: A Polymer Science Perspective
Holdcroft, S. (2014) · Chemistry of Materials · doi:10.1021/cm401445h · Cited by 481
Electrode for proton exchange membrane fuel cells: A review
Majlan, E. H., Rohendi, D., Daud, W. R. W., Husaini, T., & Haque, M. A. (2018) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2018.03.007 · Cited by 438
The recent progress and future of oxygen reduction reaction catalysis: A review
Stacy, J., Regmi, Y. N., Leonard, B., & Fan, M. (2017) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2016.09.135 · Cited by 410
Shear rheology of hard-sphere, dispersed, and aggregated suspensions, and filler-matrix composites
Genovese, D. B. (2012) · Advances in Colloid and Interface Science · doi:10.1016/j.cis.2011.12.005 · Cited by 383
Developments in fuel cell technologies in the transport sector
Alaswad, A., Baroutaji, A., Achour, H., Carton, J., Al Makky, A., & Olabi, A. G. (2016) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2016.03.164 · Cited by 378
Interfacial destabilization and atomization driven by surface acoustic waves
Qi, A., Yeo, L. Y., & Friend, J. R. (2008) · Physics of Fluids · doi:10.1063/1.2953537 · Cited by 316
Modeling drop size distributions
Babinsky, E., & Sojka, P. E. (2002) · Progress in Energy and Combustion Science · doi:10.1016/s0360-1285(02)00004-7 · Cited by 276
Ultrasonic atomization: Effect of liquid phase properties
Avvaru, B., Patil, M. N., Gogate, P. R., & Pandit, A. B. (2006) · Ultrasonics · doi:10.1016/j.ultras.2005.09.003 · Cited by 260
The Effects of Catalyst Layer Deposition Methodology on Electrode Performance
Jhong, H. “., Brushett, F. R., & Kenis, P. J. A. (2013) · Advanced Energy Materials · doi:10.1002/aenm.201200759 · Cited by 243
Physical meaning of the Sauter mean diameter of spherical particulate matter
Kowalczuk, P. B., & Drzymala, J. (2016) · Particulate Science and Technology · doi:10.1080/02726351.2015.1099582 · Cited by 229
Cerebral blood flow, blood supply, and cognition in Type 2 Diabetes Mellitus
Jansen, J. F. A., van Bussel, F. C. G., van de Haar, H. J., van Osch, M. J. P., Hofman, P. A. M., van Boxtel, M. P. J., van Oostenbrugge, R. J., Schram, M. T., Stehouwer, C. D. A., Wildberger, J. E., et al. (2016) · Scientific Reports · doi:10.1038/s41598-016-0003-6 · Cited by 196
The use of ultrasound for the fabrication of fuel cell materials
Pollet, B. G. (2010) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2010.08.021 · Cited by 194
Wang, M., Park, J. H., Kabir, S., Neyerlin, K. C., Kariuki, N. N., Lv, H., Stamenkovic, V. R., Myers, D. J., Ulsh, M., & Mauger, S. A. (2019) · ACS Applied Energy Materials · doi:10.1021/acsaem.9b01037 · Cited by 192
Rahemi Ardekani, S., Sabour Rouh Aghdam, A., Nazari, M., Bayat, A., Yazdani, E., & Saievar-Iranizad, E. (2019) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2019.104631 · Cited by 190
Investigations into ultrasound induced atomization
Ramisetty, K. A., Pandit, A. B., & Gogate, P. R. (2013) · Ultrasonics Sonochemistry · doi:10.1016/j.ultsonch.2012.05.001 · Cited by 162
Transient high-frequency ultrasonic water atomization
Barreras, F., Amaveda, H., & Lozano, A. (2002) · Experiments in Fluids · doi:10.1007/s00348-002-0456-1 · Cited by 155
Rheological Investigation on the Microstructure of Fuel Cell Catalyst Inks
Khandavalli, S., Park, J. H., Kariuki, N. N., Myers, D. J., Stickel, J. J., Hurst, K., Neyerlin, K. C., Ulsh, M., & Mauger, S. A. (2018) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.8b15039 · Cited by 153
Atomization off thin water films generated by high-frequency substrate wave vibrations
Collins, D. J., Manor, O., Winkler, A., Schmidt, H., Friend, J. R., & Yeo, L. Y. (2012) · Physical Review E · doi:10.1103/physreve.86.056312 · Cited by 151
Fuel cell development for New Energy Vehicles (NEVs) and clean air in China
Kendall, M. (2018) · Progress in Natural Science Materials International · doi:10.1016/j.pnsc.2018.03.001 · Cited by 142
Millington, B., Whipple, V., & Pollet, B. G. (2011) · Journal of Power Sources · doi:10.1016/j.jpowsour.2011.06.024 · Cited by 141
Application of non-Newtonian models to thin film flow
Myers, T. G. (2005) · Physical Review E · doi:10.1103/physreve.72.066302 · Cited by 138
Catalyst layer in PEMFC electrodes—Fabrication, characterisation and analysis
Rajalakshmi, N., & Dhathathreyan, K. S. (2006) · Chemical Engineering Journal · doi:10.1016/j.cej.2006.10.035 · Cited by 131
Modeling of PEM Fuel Cell Catalyst Layers: Status and Outlook
Sui, P., Zhu, X., & Djilali, N. (2019) · Electrochemical Energy Reviews · doi:10.1007/s41918-019-00043-5 · Cited by 120
Self-citationPark, I., Li, W., & Manthiram, A. (2010) · Journal of Power Sources · doi:10.1016/j.jpowsour.2010.05.004 · Cited by 119
Self-citationThe importance of ultrasonic parameters in the preparation of fuel cell catalyst inks
Pollet, B. G., & Goh, J. T. E. (2014) · Electrochimica Acta · doi:10.1016/j.electacta.2013.09.160 · Cited by 117
James, A., Smith, M. K., & Glezer, A. (2003) · Journal of Fluid Mechanics · doi:10.1017/s0022112002002860 · Cited by 114
On droplet formation from capillary waves on a vibrating surface
Yule, A. J., & Al-Suleimani, Y. (2000) · Proceedings of the Royal Society A Mathematical Physical and Engineering Sciences · doi:10.1098/rspa.2000.0551 · Cited by 111
Tjong, S. C. (2003) · Materials Science and Engineering R Reports · doi:10.1016/s0927-796x(03)00035-4 · Cited by 106
Increasing Proton Exchange Membrane Fuel Cell Catalyst Effectiveness Through Sputter Deposition
Haug, A. T., White, R. E., Weidner, J. W., Huang, W., Shi, S., Stoner, T., & Rana, N. (2002) · Journal of The Electrochemical Society · doi:10.1149/1.1446082 · Cited by 103
High-Efficiency Spray-Coated Perovskite Solar Cells Utilizing Vacuum-Assisted Solution Processing
Bishop, J. E., Smith, J. A., Greenland, C., Kumar, V., Vaenas, N., Game, O. S., Routledge, T. J., Wong‐Stringer, M., Rodenburg, C., & Lidzey, D. G. (2018) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.8b14859 · Cited by 103
Analysis of Inkjet Printed PEFC Electrodes with Varying Platinum Loading
Shukla, S., Stanier, D., Saha, M. S., Stumper, J., & Secanell, M. (2016) · Journal of The Electrochemical Society · doi:10.1149/2.1111607jes · Cited by 95
Huang, T.-H., Shen, H.-L., Jao, T.-C., Weng, F.-B., & Su, A. (2012) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2012.04.108 · Cited by 92
Su, H., Jao, T.-C., Barron, O., Pollet, B. G., & Pasupathi, S. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2014.05.086 · Cited by 92
Du, S., Li, W., Wu, H., Abel Chuang, P.-Y., Pan, M., & Sui, P.-C. (2020) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2020.07.241 · Cited by 88
Self-citationThe physical and biological effects of high-frequency sound-waves of great intensity
G.F.S. (1928) · Journal of the Franklin Institute · doi:10.1016/s0016-0032(28)92379-0 · Cited by 87
Dynamics of ultrasonic atomization of droplets
Deepu, P., Peng, C., & Moghaddam, S. S. (2017) · Experimental Thermal and Fluid Science · doi:10.1016/j.expthermflusci.2017.11.021 · Cited by 80
Rajalakshmi, N., & Dhathathreyan, K. S. (2008) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2008.05.100 · Cited by 76
Ultrasonic atomization-a photographic study of the mechanism of disintegration
Topp, M. (1973) · Journal of Aerosol Science · doi:10.1016/0021-8502(73)90113-4 · Cited by 74
Let’s Not Ignore the Ultrasonic Effects on the Preparation of Fuel Cell Materials
Pollet, B. G. (2014) · Electrocatalysis · doi:10.1007/s12678-014-0211-4 · Cited by 70
Viscosity measurement of industrial oils using the droplet quartz crystal microbalance
Ash, D. C., Joyce, M. J., Barnes, C., Booth, C. J., & Jefferies, A. C. (2003) · Measurement Science and Technology · doi:10.1088/0957-0233/14/11/013 · Cited by 68
The mechanism of the formation of fogs by ultrasonic waves
Sollner, K. (1936) · Transactions of the Faraday Society · doi:10.1039/tf9363201532 · Cited by 67
Zhao, J. F., Shahgaldi, S., Ozden, A., Alaefour, I. E., Li, X., & Hamdullahpur, F. (2019) · Applied Energy · doi:10.1016/j.apenergy.2019.113802 · Cited by 63
Hsieh, C., Hung, W.-M., & Chen, W. (2010) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2010.04.125 · Cited by 54
Experimental investigation on the atomization of a spherical droplet induced by Faraday instability
Liu, F., Kang, N. B., Li, Y., & Wu, Q. (2018) · Experimental Thermal and Fluid Science · doi:10.1016/j.expthermflusci.2018.09.016 · Cited by 44
Depositing Catalyst Layers in Polymer Electrolyte Membrane Fuel Cells: A Review
Strong, A., Thornberry, C., Beattie, S., Chen, R., & Coles, S. R. (2015) · Journal of Fuel Cell Science and Technology · doi:10.1115/1.4031961 · Cited by 43
Should You Trust Your Heavy Oil Viscosity Measurement?
Miller, K. A., Nelson, L. A., & Almond, R. M. (2006) · Journal of Canadian Petroleum Technology · doi:10.2118/06-04-02 · Cited by 39
Zhang, X., Chen, H., Qian, F., & Cheng, Y. (2017) · Chemical Engineering Journal · doi:10.1016/j.cej.2017.12.002 · Cited by 35
Performance of a direct formic acid fuel cell fabricated by ultrasonic spraying
Zainoodin, A. M., Tsujiguchi, T., Masdar, M. S., Kamarudin, S. K., Osaka, Y., & Kodama, A. (2018) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2018.02.024 · Cited by 30
Kayarkatte, M. K., Delikaya, Ö., & Roth, C. (2016) · ChemElectroChem · doi:10.1002/celc.201600530 · Cited by 29
Goodwin, A. R. H., Fitt, A. D., Ronaldson, K. A., & Wakeham, W. A. (2006) · International Journal of Thermophysics · doi:10.1007/s10765-006-0114-6 · Cited by 27
Oba, T., Kido, Y., & Nagasaka, Y. (2004) · International Journal of Thermophysics · doi:10.1007/s10765-004-5751-z · Cited by 22
Study on ultrasonic spray technology for the coating of vascular stent
Yi, H., Huang, J., Gu, X., & Ni, Z. (2011) · Science China Technological Sciences · doi:10.1007/s11431-011-4580-0 · Cited by 19
Performance of a DMFC with a Sputtered Pt Layer on the Electrode/Electrolyte Interface of the Anode
Xiu, Y. K., & Nakagawa, N. (2004) · Journal of The Electrochemical Society · doi:10.1149/1.1782632 · Cited by 14
Miniaturized optical viscosity sensor based on a laser-induced capillary wave
Taguchi, Y., Ebisui, A., & Nagasaka, Y. (2008) · Journal of Optics A Pure and Applied Optics · doi:10.1088/1464-4258/10/4/044008 · Cited by 14
Yasumoto, K., Hirota, N., & Terazima, M. (1999) · Physical review. B, Condensed matter · doi:10.1103/physrevb.60.9100 · Cited by 14
Maximizing the Use of Platinum Catalyst by Ultrasonic Spray Application
Engle, R. (2011) · Journal of Electrochemical Energy Conversion and Storage · doi:10.1115/1.4004462 · Cited by 14
Speeding up thermocapillary migration of a confined bubble by wall slip
Liao, Y., Li, Y.-C., Chang, Y.-C., Huang, C., & Wei, H.-H. (2014) · Journal of Fluid Mechanics · doi:10.1017/jfm.2014.117 · Cited by 13
Manufacturing of Direct Methanol Fuel Cell Electrodes by Spraying
Koraishy, B. M., Meyers, J. P., & Wood, K. L. (2011) · Journal of The Electrochemical Society · doi:10.1149/2.005112jes · Cited by 12
High Performance Membrane Electrode Assembly Fabricated by Ultrasonic Spray Technique
Huang, X., Rigdon, W. A., Neutzler, J., Larrabee, D., & Sightler, J. J. (2011) · ECS Transactions · doi:10.1149/1.3635624 · Cited by 10
Iwashima, H., 藪井, 謙., & Nagasaka, Y. (2007) · TRANSACTIONS OF THE JAPAN SOCIETY OF MECHANICAL ENGINEERS Series B · doi:10.1299/kikaib.73.1892 · Cited by 7
Research works printed but not linked: 1
- Faraday, 1831, Philos. Trans. R. Soc. London, 121, 319
Cited by
Liu, H., Ney, L., Zamel, N., & Li, X. (2022) · Applied Sciences · doi:10.3390/app12083776 · Cited by 85
“, 15 mPa s [68]), increasing the viscosity of ink will decrease the number of large droplets and increase the uniformity of the formed droplets, enhancing spraying quality.”
BackgroundInfluentialBierling, M., McLaughlin, D., Mayerhöfer, B., & Thiele, S. (2023) · Advanced Energy Materials · doi:10.1002/aenm.202203636 · Cited by 61
Yang, P., Huang, J., Li, J., Luo, K., Zhang, L., Fu, Q., Zhu, X., & Liao, Q. (2023) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2023.10.108 · Cited by 43
Using Ultrasound to Effectively Homogenise Catalyst Inks: Is this Approach Still Acceptable?
Pollet, B. G., & Kocha, S. S. (2021) · Johnson Matthey Technology Review · doi:10.1595/205651321x16196162869695 · Cited by 37
Liu, C., Luo, M., Zeis, R., Chuang, P. A., Zhang, R., Du, S., & Sui, P. (2023) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2023.08.154 · Cited by 33
Self-citation
Metadata
- Authors
- Li, W., Bi, X., Luo, M., & Sui, P.-C.
- Affiliations
- University of British Columbia (CA)
- Wuhan University of Technology (CN)
- Corresponding author
- Sui, Pang-Chieh
- Venue
- Journal of The Electrochemical Society
- Publisher
- The Electrochemical Society
- Published
- 2021-03-01
- Volume
- 168
- Issue
- 3
- Pages
- 034502
- ISSN
- 0013-4651 (ISSN-L)
- 1945-7111
- OpenAlex
- W3130213071
- Cited by
- 12
- References
- 71
- Citations by year
- 2026: 1 · 2025: 2 · 2024: 3 · 2023: 4 · 2022: 1 · 2021: 1
- FWCI
- 1.28
- Type
- journal article
- Language
- en
- Open access
- closed
- Licence
- publishingsupport.iopscience.iop.org/iop-standard/v1 (vor)
- iopscience.iop.org/info/page/text-and-data-mining (tdm)
- Locations
- Journal of The Electrochemical Society (publishedVersion)
- Funders
- National Natural Science Foundation of China (21776226)
- Fundamental Research Funds for the Central Universities (2019-JL-012)
- Hubei-100 Plan of China
- Compute Canada
- Topics
- Physical Sciences › Engineering › Computational Mechanics › Fluid Dynamics and Heat Transfer
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Fuel Cells and Related Materials
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Electrohydrodynamics and Fluid Dynamics
- Keywords
- ultrasonic atomization, catalyst ink, proton exchange membrane fuel cells, ultrasonic spraying, droplet size distribution, surface tension, viscosity, non-Newtonian fluids, volume of fluid method, dynamic meshing
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.