The DOI matches its Crossref record; 61 of the 61 references it cites were found in a registry or an index.
Wire Arc Additive Manufacturing of Stainless Steels: A Review
Open accessAbstract
Wire arc additive manufacturing (WAAM) has been considered as a promising technology for the production of large metallic structures with high deposition rates and low cost. Stainless steels are widely applied due to good mechanical properties and excellent corrosion resistance. This paper reviews the current status of stainless steel WAAM, covering the microstructure, mechanical properties, and defects related to different stainless steels and process parameters. Residual stress and distortion of the WAAM manufactured components are discussed. Specific WAAM techniques, material compositions, process parameters, shielding gas composition, post heat treatments, microstructure, and defects can significantly influence the mechanical properties of WAAM stainless steels. To achieve high quality WAAM stainless steel parts, there is still a strong need to further study the underlying physical metallurgy mechanisms of the WAAM process and post heat treatments to optimize the WAAM and heat treatment parameters and thus control the microstructure. WAAM samples often show considerable anisotropy both in microstructure and mechanical properties. The new in-situ rolling + WAAM process is very effective in reducing the anisotropy, which also can reduce the residual stress and distortion. For future industrial applications, fatigue properties, and corrosion behaviors of WAAMed stainless steels need to be deeply studied in the future. Additionally, further efforts should be made to improve the WAAM process to achieve faster deposition rates and better-quality control.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Metal Additive Manufacturing: A Review
Frazier, W. E. (2014) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-014-0958-z · Cited by 5,984
Additive manufacturing of metals
Herzog, D., Seyda, V., Wycisk, E., & Emmelmann, C. (2016) · Acta Materialia · doi:10.1016/j.actamat.2016.07.019 · Cited by 4,759
Titanium and Titanium Alloys: Fundamentals and Applications
(2003) · Wiley eBooks · doi:10.1002/3527602119 · Cited by 3,108
Khairallah, S. A., Anderson, A. T., Rubenchik, A., & King, W. E. (2016) · Acta Materialia · doi:10.1016/j.actamat.2016.02.014 · Cited by 2,766
The metallurgy and processing science of metal additive manufacturing
Sames, W. J., List, F. A., Pannala, S., Dehoff, R. R., & Babu, S. S. (2016) · International Materials Reviews · doi:10.1080/09506608.2015.1116649 · Cited by 2,529
Additive manufacturing: technology, applications and research needs
Guo, N., & Leu, M. C. (2013) · Frontiers of Mechanical Engineering · doi:10.1007/s11465-013-0248-8 · Cited by 2,073
Wire + Arc Additive Manufacturing
Williams, S., Martina, F., Addison, A. C., Ding, J., Pardal, G., & Colegrove, P. A. (2015) · Materials Science and Technology · doi:10.1179/1743284715y.0000000073 · Cited by 1,971
Ding, D., Pan, Z., Cuiuri, D., & Li, H. (2015) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-015-7077-3 · Cited by 1,648
Wu, B., Pan, Z., Ding, D., Cuiuri, D., Li, H., Xu, J., & Norrish, J. (2018) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2018.08.001 · Cited by 1,577
Thompson, S. M., Bian, L., Shamsaei, N., & Yadollahi, A. (2015) · Additive Manufacturing · doi:10.1016/j.addma.2015.07.001 · Cited by 1,179
Sing, S. L., An, J., Yeong, W. Y., & Wiria, F. E. (2016) · Journal of Orthopaedic Research · doi:10.1002/jor.23075 · Cited by 942
Grain structure control during metal 3D printing by high-intensity ultrasound
Todaro, C. J., Easton, M. A., Qiu, D., Zhang, D., Bermingham, M. J., Lui, E. W., Brandt, M., StJohn, D. H., & Qian, M. (2020) · Nature Communications · doi:10.1038/s41467-019-13874-z · Cited by 848
Dynamics of pore formation during laser powder bed fusion additive manufacturing
Martin, A. A., Calta, N. P., Khairallah, S. A., Wang, J., Depond, P. J., Fong, A. Y., Thampy, V., Guss, G. M., Kiss, A. M., Stone, K. H., et al. (2019) · Nature Communications · doi:10.1038/s41467-019-10009-2 · Cited by 711
Ding, J., Colegrove, P., Mehnen, J., Ganguly, S., Sequeira Almeida, P. M., Wang, F., & Williams, S. (2011) · Computational Materials Science · doi:10.1016/j.commatsci.2011.06.023 · Cited by 689
Yadollahi, A., Shamsaei, N., Thompson, S. M., & Seely, D. W. (2015) · Materials Science and Engineering: A · doi:10.1016/j.msea.2015.07.056 · Cited by 650
Baufeld, B., der Biest, O. V., & Gault, R. (2009) · Materials & Design (1980-2015) · doi:10.1016/j.matdes.2009.11.032 · Cited by 601
A multi-bead overlapping model for robotic wire and arc additive manufacturing (WAAM)
Ding, D., Pan, Z. S., Cuiuri, D., & Li, H. (2014) · Robotics and Computer-Integrated Manufacturing · doi:10.1016/j.rcim.2014.08.008 · Cited by 577
Colegrove, P. A., Coules, H., Fairman, J., Martina, F., Kashoob, T., Mamash, H., & Cozzolino, L. D. (2013) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2013.04.012 · Cited by 567
Scientific, technological and economic issues in metal printing and their solutions
DebRoy, T., Mukherjee, T., Milewski, J. O., Elmer, J. W., Ribic, B., Blecher, J. J., & Zhang, W. (2019) · Nature Materials · doi:10.1038/s41563-019-0408-2 · Cited by 543
Wang, L., Xue, J., & Wang, Q. (2019) · Materials Science and Engineering A · doi:10.1016/j.msea.2019.02.078 · Cited by 496
Characterization of stainless steel parts by Laser Metal Deposition Shaping
Zhang, K., Wang, S., Liu, W., & Shang, X. (2013) · Materials & Design (1980-2015) · doi:10.1016/j.matdes.2013.09.006 · Cited by 485
Self-citationMa, M., Wang, Z., & Zeng, X. (2017) · Materials Science and Engineering: A · doi:10.1016/j.msea.2016.12.112 · Cited by 431
Building blocks for a digital twin of additive manufacturing
Knapp, G. L., Mukherjee, T., Zuback, J. S., Wei, H. L., Palmer, T. A., De, A., & DebRoy, T. (2017) · Acta Materialia · doi:10.1016/j.actamat.2017.06.039 · Cited by 414
Gu, J., Ding, J., Williams, S. W., Gu, H., Bai, J., Zhai, Y., & Ma, P. (2016) · Materials Science and Engineering: A · doi:10.1016/j.msea.2015.10.101 · Cited by 413
Scipioni Bertoli, U., Guss, G., Wu, S., Matthews, M. J., & Schoenung, J. M. (2017) · Materials & Design · doi:10.1016/j.matdes.2017.09.044 · Cited by 412
Chen, X., Li, J., Cheng, X., He, B., Wang, H., & Huang, Z. (2017) · Materials Science and Engineering A · doi:10.1016/j.msea.2017.05.024 · Cited by 401
Heat transfer and material flow during laser assisted multi-layer additive manufacturing
Manvatkar, V., De, A., & DebRoy, T. (2014) · Journal of Applied Physics · doi:10.1063/1.4896751 · Cited by 362
A digital twin for rapid qualification of 3D printed metallic components
Mukherjee, T., & DebRoy, T. (2019) · Applied Materials Today · doi:10.1016/j.apmt.2018.11.003 · Cited by 339
Ding, D., Pan, Z. S., Cuiuri, D., et al. (2015) · Robotics and Computer-Integrated Manufacturing · doi:10.1016/j.rcim.2015.01.003 · Cited by 336
Review: The Impact of Metal Additive Manufacturing on the Aerospace Industry
Mohd Yusuf, S., Cutler, S., & Gao, N. (2019) · Metals · doi:10.3390/met9121286 · Cited by 332
Seede, R., Shoukr, D., Zhang, B., Whitt, A., Gibbons, S., Flater, P., Elwany, A., Arroyave, R., & Karaman, I. (2020) · Acta Materialia · doi:10.1016/j.actamat.2019.12.037 · Cited by 301
Aluminum with dispersed nanoparticles by laser additive manufacturing
Lin, T.-C., Cao, C., Sokoluk, M., Jiang, L., Wang, X., Schoenung, J. M., Lavernia, E. J., & Li, X. (2019) · Nature Communications · doi:10.1038/s41467-019-12047-2 · Cited by 291
Ahn, D.-G. (2016) · International Journal of Precision Engineering and Manufacturing-Green Technology · doi:10.1007/s40684-016-0048-9 · Cited by 268
Yang, D., Wang, G., & Zhang, G. (2017) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2017.01.024 · Cited by 267
Shaped metal deposition of a nickel alloy for aero engine applications
Clark, D., Bache, M. R., & Whittaker, M. T. (2007) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2007.10.051 · Cited by 245
Xiong, J., Li, Y., Li, R., & Yin, Z. (2018) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2017.09.020 · Cited by 243
McAndrew, A. R., Alvarez Rosales, M., Colegrove, P. A., Hönnige, J. R., Ho, A., Fayolle, R., Eyitayo, K., Stan, I., Sukrongpang, P., Crochemore, A., et al. (2018) · Additive Manufacturing · doi:10.1016/j.addma.2018.03.006 · Cited by 243
Gray, G. T., Livescu, V., Rigg, P. A., Trujillo, C. P., Cady, C. M., Chen, S. R., Carpenter, J. S., Lienert, T. J., & Fensin, S. J. (2017) · Acta Materialia · doi:10.1016/j.actamat.2017.07.045 · Cited by 238
Analysis of Welded Structures: Residual Stresses, Distortion, and their Consequences
Masubuchi, K. (1980) · Cited by 219
Syed, W. U. H., Pinkerton, A. J., & Li, L. (2005) · Applied Surface Science · doi:10.1016/j.apsusc.2005.01.138 · Cited by 207
Dimensionless numbers in additive manufacturing
Mukherjee, T., Manvatkar, V., De, A., & DebRoy, T. (2017) · Journal of Applied Physics · doi:10.1063/1.4976006 · Cited by 196
A Review on Laser Powder Bed Fusion of Inconel 625 Nickel-Based Alloy
Tian, Z., Zhang, C., Wang, D., Liu, W., Fang, X., Wellmann, D., Zhao, Y., & Tian, Y. (2019) · Applied Sciences · doi:10.3390/app10010081 · Cited by 196
Self-citationAdaptive path planning for wire-feed additive manufacturing using medial axis transformation
Ding, D., Pan, Z. S., Cuiuri, D., Li, H., & Larkin, N. (2016) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2016.06.036 · Cited by 174
Caballero, A., Ding, J., Ganguly, S., & Williams, S. (2019) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2019.01.007 · Cited by 173
Ma, Y., Cuiuri, D., Hoye, N., Li, H., & Pan, Z. S. (2015) · Materials Science and Engineering A · doi:10.1016/j.msea.2015.02.051 · Cited by 167
Mohr, G., Altenburg, S. J., Ulbricht, A., Heinrich, P., Baum, D., Maierhofer, C., & Hilgenberg, K. (2020) · Metals · doi:10.3390/met10010103 · Cited by 167
Xiong, J., Zhang, G., Qiu, Z., & Li, Y. (2012) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2012.10.009 · Cited by 153
Hosseini, V. A., Högström, M., Hurtig, K., Bermejo, M. A. V., Stridh, L.-E., & Karlsson, L. (2019) · Welding in the World · doi:10.1007/s40194-019-00735-y · Cited by 150
Lin, J., Lv, Y., Liu, Y., Sun, Z., Wang, K., Li, Z., Wu, Y., & Xu, B. (2016) · Journal of the mechanical behavior of biomedical materials/Journal of mechanical behavior of biomedical materials · doi:10.1016/j.jmbbm.2016.12.015 · Cited by 149
Laser Powder Bed Fusion of Precipitation-Hardened Martensitic Stainless Steels: A Review
Zai, L., Zhang, C., Wang, Y., Guo, W., Wellmann, D., Tong, X., & Tian, Y. (2020) · Metals · doi:10.3390/met10020255 · Cited by 145
Self-citationLaser Powder Bed Fusion of Inconel 718: Residual Stress Analysis Before and After Heat Treatment
Barros, R., Silva, F. J. G., Gouveia, R. M., Saboori, A., Marchese, G., Biamino, S., Salmi, A., & Atzeni, E. (2019) · Metals · doi:10.3390/met9121290 · Cited by 143
Yang, D., He, C., & Zhang, G. (2015) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2015.08.021 · Cited by 141
Precipitation behavior of aluminum alloy 2139 fabricated using additive manufacturing
Brice, C., Shenoy, R. N., Kral, M. V., & Buchannan, K. (2015) · Materials Science and Engineering A · doi:10.1016/j.msea.2015.08.088 · Cited by 138
Challenges associated with the wire arc additive manufacturing (WAAM) of aluminum alloys
Thapliyal, S. (2019) · Materials Research Express · doi:10.1088/2053-1591/ab4dd4 · Cited by 124
Zhang, X., Wang, K., Zhou, Q., Ding, J., Ganguly, S., Grasso, M., Yang, D., Xu, X., Dirisu, P., & Williams, S. (2019) · Materials Science and Engineering A · doi:10.1016/j.msea.2019.138097 · Cited by 123
Solidification-driven orientation gradients in additively manufactured stainless steel
Polonsky, A. T., Lenthe, W. C., Echlin, M. P., et al. (2019) · Acta Materialia · doi:10.1016/j.actamat.2019.10.047 · Cited by 115
Welding Technology in Additive Manufacturing Processes of 3D Objects
Korzhyk, V., Khaskin, V. Y., Voitenko, O. M., Sydorets, V. M., & DOLIANOVSKAIA, O. (2017) · Materials science forum · doi:10.4028/www.scientific.net/msf.906.121 · Cited by 52
Applying Selective Laser Melting to Join Al and Fe: An Investigation of Dissimilar Materials
Nguyen, D. S., Park, H., & Lee, C.-M. (2019) · Applied Sciences · doi:10.3390/app9153031 · Cited by 43
Denti, L., & Sola, A. (2019) · Metals · doi:10.3390/met9121284 · Cited by 37
Anisotropic Mechanical Properties in a Big-Sized Ti-6Al-4V Plate Fabricated by Electron Beam Melting
Wang, P., Nai, M. L. S., Tan, X., Sin, W. J., Tor, S. B., & Wei, J. (2016) · Springer eBooks · doi:10.1007/978-3-319-48254-5_1 · Cited by 33
Fracture Toughness of Hybrid Components with Selective Laser Melting 18Ni300 Steel Parts
Santos, L. M. S., Jesus, J. S., Ferreira, J. A. M., Costa, J. D., & Capela, C. A. B. (2018) · Applied Sciences · doi:10.3390/app8101879 · Cited by 29
Cited by
Svetlizky, D., Das, M., Zheng, B., Vyatskikh, A. L., Bose, S., Bandyopadhyay, A., Schoenung, J. M., Lavernia, E. J., & Eliaz, N. (2021) · Materials Today · doi:10.1016/j.mattod.2021.03.020 · Cited by 1,371
Directed Energy Deposition (DED) Process: State of the Art
Ahn, D.-G. (2021) · International Journal of Precision Engineering and Manufacturing-Green Technology · doi:10.1007/s40684-020-00302-7 · Cited by 803
Jafari, D., Vaneker, T. H. J., & Gibson, I. (2021) · Materials & Design · doi:10.1016/j.matdes.2021.109471 · Cited by 605
The Current State of Research of Wire Arc Additive Manufacturing (WAAM): A Review
Treutler, K., & Wesling, V. (2021) · Applied Sciences · doi:10.3390/app11188619 · Cited by 293
Wire arc additive manufacturing of low alloyed steels, copper aluminum alloys, and their bimetals
Karamimoghadam, M., Aghayar, Y., Forooghi, F., Denora, V., Mohammadi, M., Contuzzi, N., & Casalino, G. (2025) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-025-16436-4 · Cited by 18
Metadata
- Authors
- Jin, W., Zhang, C., Jin, S., Tian, Y., Wellmann, D., & Liu, W.
- Venue
- Applied Sciences
- Publisher
- MDPI AG
- Published
- 2020-02-25
- Volume
- 10
- Issue
- 5
- Pages
- 1563
- ISSN
- 2076-3417 (ISSN-L)
- OpenAlex
- W3007058305
- Cited by
- 388
- References
- 61
- FWCI
- 22.28
- Type
- journal article
- Language
- en
- Open access
- gold
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.