Battery Management System Hardware Concepts: An Overview
Open accessThe DOI matches its Crossref record; 35 of the 35 references it cites were found in a registry or an index; 2 of the 117 sources its claims cite were checked for support.
Abstract
This paper focuses on the hardware aspects of battery management systems for electric vehicle and stationary applications.
Overview
CoChat Summary
TL;DR
This paper reviews hardware concepts for battery management systems in electric vehicle and stationary applications, covering requirements, pack topologies, measurement, balancing, and safety/reliability. It illustrates these concepts with four disassembled commercial EV battery packs and compares implementation choices.
Key findings
- Voltage acquisition accuracy strongly affects SOC estimation: with ±1 mV voltage accuracy, the paper reports a base SOC error of 0.2% for NMC cells but 5.9% for LFP cells; typical BMS AFEs have about ±1 mV accuracy and 12–16 bit full scale, giving about 380 µV resolution (14-bit for BQ76PL536A).
- Observed commercial packs used passive balancing with small currents around 100 mA (balancing resistances of 30–40 Ω at an assumed 4.2 V), dissipating 387–430 mW per cell; active balancing was not observed by the authors in commercially available automotive battery packs in volume markets.
- Four EV examples are described: Mitsubishi i-MiEV with 88 prismatic cells and LTC6802G-2 per module PCB; VW e-Up with 17 modules of six series-connected cell pairs and nine MAX11068 daisy-chained via I2C; Tesla Model-S with 7104 18,650 cells in a 96s74p configuration, 16 modules, nominal 355 V, and bq76PL536A-Q1; smart fortwo electric drive with 90 pouch cells.
- Insulation monitoring standards are summarized: for DC systems a minimum insulation resistance of 100 Ω/V is recommended, for AC systems 500 Ω/V; ECE-R100 demands minimum 500 Ω/V, and DIN61557-8 allows a measuring time of at most 100 s.
Methods
- Design: narrative overview/review of BMS hardware for lithium-ion batteries, organized around requirements, topologies, measurement, balancing, and safety/reliability.
- Data/sample: four commercially available EV battery packs were disassembled and analyzed (Mitsubishi i-MiEV, smart fortwo electric drive, VW e-Up, Tesla Model-S; for Tesla only one module was available, with some data based on an AVL presentation). The paper also draws on datasheets, standards, and literature.
- Analysis: qualitative comparison of topologies, components, and implementation choices, supported by tables and figures; no new experimental performance testing is reported.
Limitations
- Stated: due to the huge variety of applications and systems, it is not possible to consider every existing facet; no manufacturer documentation was available for the remaining vehicles/batteries, so information on them is less detailed than for the i-MiEV; Tesla data are based on an AVL presentation and the authors’ analysis of a single separately purchased module.
- Stated: the BMS IC table is already outdated at the time it is printed, and not all datasheet values are easily comparable because conditions differ between suppliers.
- Evident from the text: as an overview, it does not provide a systematic quantitative review or primary experimental validation, and its real-world examples are limited to four battery packs and selected components.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
2 Valid · 17 Not valid · 89 Not checked · 160 Own results and interpretations
Every source the paper cites for this claim was checked and supports it.
In the paper
“According to [59], the main hazards inside lithium-ion battery packs are exposure to high voltage, arcing, fire, vented gas combustibility and vented gas toxicity.”
§ Battery Management System Hardware Concepts: An Overview > 6. Safety and Reliability
What the sources say
- Supportedcites [59] Rosewater, 2015, Analyzing system safety in lithium-ion grid energy storage, J. Power Sources source
The Introduction (p. 1) lists voltage, arc-flash/blast potential, fire potential, vented-gas combustibility, and vented-gas toxicity as properties of lithium-ion batteries that can develop hazardous conditions. It notes that the list is not comprehensive, but it directly supports the five hazards named in the claim. (LLM, conf=0.92)
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“if a ±1 mV voltage accuracy system is used to calculate the SOC on NMC type lithium cells, then a base error of 0.2 % can be expected.”
§ Battery Management System Hardware Concepts: An Overview > 2.2. Voltage Acquisition
plainstates a possible cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“If the same acquisition mimic is used to acquire an LFP cell's SOC, then a base error of 5.9 % has to be expected.”
§ Battery Management System Hardware Concepts: An Overview > 2.2. Voltage Acquisition
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Case 1: Using a series connection of m times n parallel cells, m voltage channels would be needed.(see Figure 2e)”
§ Battery Management System Hardware Concepts: An Overview > 3. Topologies of BMS
hedgedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Case 2: Using a parallel connection of n strings of m cells in series, m • n voltage measurement channels would be needed.(see Figure 2d)”
§ Battery Management System Hardware Concepts: An Overview > 3. Topologies of BMS
hedgedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
90 more claims
Create a free account to see all 268 claims and to verify the 50 references still open.
- It may state two separate claims as one. 82
- Probably not a substantial claim. 133
- The quote only partly states this claim. 11
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Battery Management System Hardware Concepts: An Overview > Example (1) Mitsubishi i-MiEV
“The PCB on top of the modules is called the Cell Management Unit (CMU) in the official service manual for the car [30].”
§ Battery Management System Hardware Concepts: An Overview > References
“30. Sensitec. CDS4150 MagnetoResistive Current Sensor. Technical Report, 2016.”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Battery Management System Hardware Concepts: An Overview > 4.1.2. Contactless Current Sensors
“One of the main disadvantages of the Hall effect based sensors is their limited bandwidth-usually not higher than a few ten kHz”
§ Battery Management System Hardware Concepts: An Overview > 4.1.2. Contactless Current Sensors
“such as Allegro Microsystems' A136x product family (Worcester, MA, USA) [37] (120 kHz) or LEM's LTC200 series sensors (100 kHz) [38]”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Battery Management System Hardware Concepts: An Overview > Example (4) Tesla Model-S
“According to [29], the whole battery consists of 7104 single 18,650 cells”
§ Battery Management System Hardware Concepts: An Overview > References
“29. Pettigrew, W. Selecting the Most Effective Current Sensing Technology. Power Electron. Eur. 2007, 8, 27-31.”
Citations
Cites
Waag, W., Fleischer, C., & Sauer, D. U. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2014.02.064 · Cited by 1,059 · cited 1×
“To overcome the resulting problems for SOC estimation, there are approaches using algorithms and parametrised models to combine the available data and retrieve usable values [12], which however is beyond the scope of this work.”
MethodSelf-citationCurrent Sensing Techniques: A Review
Ziegler, S., Woodward, R. C., Iu, H. H.-C., & Borle, L. J. (2009) · IEEE Sensors Journal · doi:10.1109/jsen.2009.2013914 · Cited by 774 · cited 3×
“The measurement range is limited by the accuracy of the voltage measurement [10,31].”
BackgroundMethodBattery equalization active methods
Gallardo-Lozano, J., Romero-Cadaval, E., Milanes-Montero, M. I., & Guerrero-Martinez, M. A. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2013.08.026 · Cited by 542 · cited 1×
“An overview of the possible topologies is given in [55,58].”
BackgroundProduction caused variation in capacity aging trend and correlation to initial cell performance
Baumhöfer, T., Brühl, M., Rothgang, S., & Sauer, D. U. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2013.08.108 · Cited by 421 · cited 2×
“[23] has reviewed the changes of different cells’ capacities in a batch of 18,650 consumer cells with the same initial capacity and that were stressed with the same load profile.”
BackgroundSelf-citationA failure modes, mechanisms, and effects analysis (FMMEA) of lithium-ion batteries
Hendricks, C., Williard, N., Mathew, S., & Pecht, M. (2015) · Journal of Power Sources · doi:10.1016/j.jpowsour.2015.07.100 · Cited by 381 · cited 1×
“Especially lithium plating at low temperatures is a serious risk, as it can lead to the formation of dendrites and subsequent internal short circuits of the cells [69].”
BackgroundInternal short circuit detection for battery pack using equivalent parameter and consistency method
Ouyang, M., Zhang, M., Feng, X., Lu, L., Li, J., He, X., & Zheng, Y. (2015) · Journal of Power Sources · doi:10.1016/j.jpowsour.2015.06.087 · Cited by 309 · cited 1×
“Some diagnostic algorithms are proposed in literature to detect internal short circuits [71,72] at early stages.”
BackgroundShang, Y., Zhang, C., Cui, N., & Guerrero, J. M. (2015) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2014.2345672 · Cited by 281 · cited 3×
“(a) causes for the imbalance of several battery cells, figure based on [57]; (b) categorization of different balancing methods, shown names of non-dissipative methods refer to the direction of energy transfer, figure based on [55].”
BackgroundHandbuch Lithium-Ionen-Batterien
(2013) · doi:10.1007/978-3-642-30653-2 · Cited by 252
Instantaneous measurement of the internal temperature in lithium-ion rechargeable cells
Srinivasan, R., Carkhuff, B. G., Butler, M. H., & Baisden, A. C. (2011) · Electrochimica Acta · doi:10.1016/j.electacta.2011.03.136 · Cited by 218
Sensorless battery temperature measurements based on electrochemical impedance spectroscopy
Raijmakers, L. H. J., Danilov, D. L., van Lammeren, J. P. M., Lammers, M. J. G., & Notten, P. H. L. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2013.09.005 · Cited by 203
Research works printed but not linked: 7
- Korthauer, R. (2013). Sensorik/Messtechnik. Handbuch lithium-ionen-Batterien, Springer. Chapter 11. · DOI · Paper page
- Korthauer, R. (2013). Relais, Kontaktoren, Kabel und Steckverbinder. Handbuch lithium-ionen-Batterien, Springer. Chapter 12. · DOI · Paper page
- Könekamp, A., and Hennige, V. (2015, January 26–29). The Tesla Model S Battery: A Pack Analysis Study. Proceedings of the Advanced Automotive & Stationary Battery Conference, Mainz, Germany.
- Pettigrew, 2007, Selecting the Most Effective Current Sensing Technology, Power Electron. Eur., 8, 27
- Institute of Electrical and Electronics Engineers (1998). IEEE Guide for the Protection of Stationary Battery Systems, Institute of Electrical and Electronics Engineers.
- Lelie, M., and Sauer, D.U. (2016, January 25–27). Approach to a “Wireless”, Cell Integrated Battery Management System. Proceedings of the Kraftwerk Batterie—Advanced Battery Power Conference 2016, Münster, Germany.
- Bolsinger, C., Brix, J., and Dragan, M. (2016, January 25–27). High Frequency Model of lithium-ion Batteries for Powerline Communication. Proceedings of the Kraftwerk Batterie—Advanced Battery Power Conference 2016, Münster, Germany.
Cited by
Items 101–200 of 284
IoT-integrated smart energy management system with enhanced ANN controller for small-scale microgrid
Mariyaraj, A., & Padmanabhan, T. S. (2024) · Electrical Engineering · doi:10.1007/s00202-024-02448-y · Cited by 17
Zafar, M. H., Bukhari, S. M. S., Houran, M. A., Mansoor, M., Khan, N. M., & Sanfilippo, F. (2024) · Case Studies in Thermal Engineering · doi:10.1016/j.csite.2024.105002 · Cited by 21
Lekouaghet, B., Merrouche, W., Bouguenna, E., Taghezouit, B., & Benghanem, M. (2024) · Journal of Power Sources · doi:10.1016/j.jpowsour.2024.235615 · Cited by 20
Hossain, M. N., Rahman, M. M., & Ramasamy, D. (2025) · Measurement · doi:10.1016/j.measurement.2025.117618 · Cited by 26
Lee, D., Lee, P., Baek, I., Kwon, S., & Kim, J. (2023) · Journal of Energy Storage · doi:10.1016/j.est.2023.109338 · Cited by 19
Messing, M., Rahimifard, S., Shoa, T., & Habibi, S. R. (2021) · IEEE Access · doi:10.1109/access.2021.3095938 · Cited by 18
“Sub-modules of parallel cells are often treated as single cells with higher capacities to reduce the number of sensors used in the battery pack [32].”
BackgroundAnalysis and Synthesis of Architectures for Automotive Battery Management Systems
Schärtel, L., Reick, B., Pfeil, M., & Stetter, R. (2022) · Applied Sciences · doi:10.3390/app122110756 · Cited by 15
“If the accurate one is not working as it is supposed to, many systems still generate binary information about the actual voltage [26].”
BackgroundA Comprehensive Overview of the Impacting Factors on a Lithium-Ion-Battery’s Overall Efficiency
Kremzow-Tennie, S., Scholz, T. F., Pautzke, F., Popp, A., Fechtner, H., & Schmuelling, B. (2022) · Power Electronics and Drives · doi:10.2478/pead-2022-0002 · Cited by 19
“(Lelie et al., 2018).”
BackgroundState of Charge Estimation for Batteries Based on Common Feature Extraction and Transfer Learning
Li, X., Xu, J., Ding, X., & Lyu, H. (2023) · Batteries · doi:10.3390/batteries9050266 · Cited by 18
Cao, Y. F., & Qahouq, J. A. A. (2019) · Applied Sciences · doi:10.3390/app9204249 · Cited by 14
Lamprecht, A., Riesterer, M., & Steinhorst, S. (2020) · IEEE International Conference on Omni-layer Intelligent Systems (COINS) · doi:10.1109/coins49042.2020.9191421 · Cited by 22
“The battery pack is modeled after a Tesla Model S battery pack with 18650 cells in 96S74P configuration and 85 kWh capacity [17].”
MethodRao, K. D., Rao, K. D., Pavani, P., Prasad, K. V. S. R., Damarla, I., & Phaniteja, B. (2025) · Electrical Engineering · doi:10.1007/s00202-025-03102-x · Cited by 24
“In addition, it interfaces using CAN bus, Modbus, or Ethernet for communication and data transmission from the battery pack to the traction control system [96].”
Zhao, X., Sun, B., Zhang, W., He, X., Ma, S., & Zhang, J. (2024) · Journal of Energy Storage · doi:10.1016/j.est.2024.113005 · Cited by 15
Qu, J., Wang, Y., Zheng, R., Li, M., & Zhang, D. (2024) · Journal of Energy Storage · doi:10.1016/j.est.2024.113086 · Cited by 19
Tashakor, N., Dusengimana, J., Bayati, M., Kersten, A., Schotten, H. D., & Goetz, S. M. (2023) · Batteries · doi:10.3390/batteries9020099 · Cited by 14
“Compared to conventional BMSs, as shown in [78,82], the proposed technique can reduce the number of sensors from 2N + 2 (sensors for module current and module voltage) in a battery string with N modules to only two at the output terminals (output voltage and current of the pack).”
MethodA Safety Concept for an Automotive Lithium-based Battery Management System
Marcos, D., Perez-Cerrolaza, J., Zubizarreta, P., et al. (2019) · doi:10.1109/ev.2019.8892986 · Cited by 13
“In an automotive application, the BMS is usually divided in a three-subsystem topology [7] as shown in Figure 1(b): BMS slave, BMS master and powerbox.”
MethodDeep Learning-Based False Sensor Data Detection for Battery Energy Storage Systems
Lee, H., Bere, G., Kim, K., Ochoa, J. J., Park, J., & Kim, T. (2020) · IEEE CyberPELS (CyberPELS) · doi:10.1109/cyberpels49534.2020.9311542 · Cited by 15
“It is noted that the study in the sensor board layer faults have been already reported by many other researchers and the model-based methods have been mainly used to detect the battery sensor board failures [15], [19], [21], [22].”
MethodFPGA-Based battery management system for real-time monitoring and instantaneous SOC prediction
Saday, A., Özkan, İ. A., & Saritas, I. E. (2023) · International Journal of Applied Mathematics Electronics and Computers · doi:10.18100/ijamec.1233451 · Cited by 14
“Controlling all these sensors and circuit elements in the system and providing calculation processes is only possible with the use of powerful processors [4, 8, 9].”
BackgroundLithium-Ion Battery Thermal Runaway Suppression Using Water Spray Cooling
Huhn, E., Braxtan, N. L., Chen, S.-E., Bombik, A., Zhao, T., Ma, L., Sherman, J. V., & Roghani, S. (2025) · Energies · doi:10.3390/en18112709 · Cited by 13
“Current BMSs are not integral within battery cells [53] and can remain a challenge for rapid response to battery fires.”
Joddumahanthi, V., & Knypiński, Ł. (2024) · Progress in Applied Electrical Engineering (PAEE) · doi:10.1109/paee63906.2024.10701438 · Cited by 14
“The authors in [14] provided information on the hardware features of battery management systems for electric vehicles in addition to their applications.”
BackgroundRavi, R., & Surendra, U. (2021) · Advances in mechatronics and mechanical engineering (AMME) book series · doi:10.4018/978-1-7998-7626-7.ch001 · Cited by 11
Blömeke, A., Zappen, H., Ringbeck, F., Frie, F., Wasylowski, D., & Sauer, D. U. (2024) · Communications Engineering · doi:10.1038/s44172-024-00203-6 · Cited by 12
“Integral to a BMS is its ability to balance battery cells, which aims to achieve uniform state-of-charges (SoCs) across cells 1 .”
Self-citationActive balancing method for series battery pack based on flyback converter
Guo, X., Geng, J., Zhen, L., et al. (2020) · IET Circuits Devices & Systems · doi:10.1049/iet-cds.2020.0008 · Cited by 10
Sizing Scheme of Hybrid Energy Storage System for Electric Vehicle
Shende, V., Singh, K. V., Bansal, H. O., & Singh, D. (2021) · Iranian Journal of Science and Technology Transactions of Electrical Engineering · doi:10.1007/s40998-021-00416-x · Cited by 11
Sbarra, R. G., Pasquali, M., Coppotelli, G., Gaudenzi, P., di Ienno, D., Ciancarelli, C., & Picci, N. (2025) · Energies · doi:10.3390/en18215858 · Cited by 15
“…as electric vehicles (EVs) can provide an accurate estimation of monitoring fundamental parameters such as State of Charge (SOC), State of Health (SOH), and Remaining Useful Life (RUL), also thanks to the possibility of regular calibration and maintenance operations performed on the ground [4].”
Evaluating fault detection strategies for lithium-ion batteries in electric vehicles
Dasari, H. A., & Rammohan, A. (2024) · Engineering Research Express · doi:10.1088/2631-8695/ad68c7 · Cited by 11
Active Li-ion Battery Charge Balancing System Based on Flyback Converter
Brandis, A., Pelin, D., Topić, D., et al. (2020) · IEEE International Symposium on Power Electronics for Distributed Generation Systems (PEDG) · doi:10.1109/pedg48541.2020.9244396 · Cited by 9
Possibilities for a Quick Onsite Safety-State Assessment of Stand-Alone Lithium-Ion Batteries
Koch, D., & Schweiger, H. (2022) · Batteries · doi:10.3390/batteries8110213 · Cited by 9
“one or more module controllers, that gather sensor data from their single cells and transmit and receive data to and from a head unit, respectively [22].”
BackgroundAn, C., Wang, S., Lin, L., Ding, X., Deng, Q., & Hu, N. (2024) · Microstructures · doi:10.20517/microstructures.2023.64 · Cited by 10
Dimitrov, B., Collier, G., & Cruden, A. J. (2019) · World Electric Vehicle Journal · doi:10.3390/wevj10040059 · Cited by 9
“In [14] important safety issues are described and a BMS with fuses between the battery pack and the ASIC is suggested.”
BackgroundELEKTRİKLİ ARAÇLARDA KULLANILAN BATARYALAR VE TERMAL YÖNETİM SİSTEMLERİNİN İNCELENMESİ
Muhammet Yasin, K. A. B. A., Kalkan, O., & Çelen, A. (2021) · Konya Journal of Engineering Sciences · doi:10.36306/konjes.945819 · Cited by 10
Past, present, and future of electrochemical energy storage: A brief perspective
Ulissi, U., & Raccichini, R. (2021) · Frontiers of nanoscience · doi:10.1016/b978-0-12-821434-3.00013-2 · Cited by 8
Son, D., Song, Y., Park, S., Oh, J., & Kim, S. (2025) · Energy · doi:10.1016/j.energy.2025.134434 · Cited by 15
Comparative Analysis of Passive, Active, and Hybrid Cell Balancing for Optimal Battery Performance
Lim, W. C., Teo, B. C. T., Lim, X. Y., et al. (2024) · International Conference on Electronics, Information, and Communication (ICEIC) · doi:10.1109/iceic61013.2024.10457118 · Cited by 8
“Nevertheless, there are distinct benefits to integrating cell balancing systems directly on a chip [7].”
BackgroundSingh, G. K., Patel, J. R., & Rathod, M. K. (2024) · Energy Storage · doi:10.1002/est2.70036 · Cited by 10
“The primary purpose of a BTMS is to ensure optimal battery performance, longevity, and safety by maintaining the battery within a specified temperature range [3].”
Module-Level Modelling Approach for a Cloudbased Digital Twin Platform for Li-Ion Batteries
Lizaso-Eguileta, O., Martinez-Laserna, E., Rivas, M., Miguel, E., Iraola, U., & Cantero, I. (2021) · IEEE Vehicle Power and Propulsion Conference (VPPC) · doi:10.1109/vppc53923.2021.9699271 · Cited by 12
Fault detection of Lithium-Ion Battery in Electric Vehicles Considering Ageing Effects
Ahooyi, S. S., & Abdollahi, F. (2022) · International Conference on Control, Instrumentation, and Automation · doi:10.1109/iccia54998.2022.9737186 · Cited by 15
Li, H., Yuan, H., Shi, H., et al. (2025) · IEEE Access · doi:10.1109/access.2025.3548785 · Cited by 7
“…the voltage and current of the battery cluster, calculate the system insulation information, collect the information of the secondary control, estimate the battery SOX status, realize the judgment of fault information, and control the protection contactor of the battery cluster sys-tem [18].”
Comparative Analysis on Deep Learning Methods to Estimate the State of Charge in Li-ion Battery
Vijay Vignesh, S., & Suyampulingam, A. (2022) · IEEE Mysore Sub Section International Conference (MysuruCon) · doi:10.1109/mysurucon55714.2022.9972355 · Cited by 8
“The Battery Management system is not only proposed for State estimation (SOC, SOH) and also for Battery cell monitoring, charge / discharge control, battery protection, heat management, fault diagnosis, data storage, and data acquisition for the system [3], [4], [5].”
BackgroundHerlambang, Y. D., Sulistiyo, W., Margana, M., Apriandi, N., Nursaputro, S. T., Marliyati, M., Setiyo, M., Purwanto, W., Rochman, M. L., & Shyu, J. (2024) · Automotive Experiences · doi:10.31603/ae.10506 · Cited by 17
“An example of this is a solar power plant embedded in the exposed body of the car [26] – [28].”
BackgroundBattery Management System for Electrical Devices: A Review
Bhat, S., & Sudharshana (2024) · International Conference on Image Processing and Capsule Networks (ICIPCN) · doi:10.1109/icipcn63822.2024.00152 · Cited by 8
“BMS hardware issues are presented in [42].”
FOBSS: Monitoring Data from a Modular Battery System
Steinbuß, G., Rzepka, B., Bischof, S., Blank, T., & Böhm, K. (2019) · ACM International Conference on Future Energy Systems (e-Energy) · doi:10.1145/3307772.3331020 · Cited by 9
“So they must be monitored closely [10].”
Çelen, A., & Muhammet Yasin, K. A. B. A. (2021) · Fırat Üniversitesi Mühendislik Bilimleri Dergisi · doi:10.35234/fumbd.728143 · Cited by 7
“[5] Lelie M, Braun T, Knips M, Nordman,H, Ringbeck F, Zappen H, Sauer D.”
BackgroundDevelopment of Internet of Things-Enabled Smart Battery Management System
Ekuewa, O. I., Afolabi, B. B., Ajibesin, S. O., Atanda, O. S., Oyegoke, M. A., & Olanrewaju, J. M. (2022) · European Journal of Electrical Engineering and Computer Science · doi:10.24018/ejece.2022.6.6.467 · Cited by 7
Estimating the State of Charge in Lithium Primary Batteries: Recent Advances and Critical Insights
Roth, S., Wesolowski, D. E., Schrock, D. J., Schorr, N. B., & Chabi, S. (2025) · Advanced Energy and Sustainability Research · doi:10.1002/aesr.202400407 · Cited by 7
A review on fault-tolerant control strategies for lithium-ion battery systems
Ghaeminezhad, N., Wang, Z., & Ouyang, Q. (2022) · Transactions of the Institute of Measurement and Control · doi:10.1177/01423312221119065 · Cited by 7
“Over-discharge: Over-discharge fault generally arises from inaccurate measured values of voltage, current, and incorrect SOC estimation that is mostly due to sensor failures and battery inconsistencies (Lelie et al., 2018; Singh et al., 2014).”
BackgroundConcha, E., Ricardo Lizana, F., Rivera, S., et al. (2024) · Electronics · doi:10.3390/electronics13224409 · Cited by 6
On the efficacy of SoC-preconditioning on the utilization of battery packs in Electric Vehicles
Lamprecht, A., Garikapati, A., Narayanaswamy, S., Machleid, J., & Steinhorst, S. (2021) · Microprocessors and Microsystems · doi:10.1016/j.micpro.2020.103711 · Cited by 8
AI-based intelligent energy storage using Li-ion batteries
Suciu, G. D., Badicu, A., Beceanu, C., Yumlu, M. S., Kaya, Y., Kizak, K. G., & Tahtasakal, F. (2021) · International Symposium on Advanced Topics in Electrical Engineering · doi:10.1109/atee52255.2021.9425328 · Cited by 7
“Another recent study [6] presents an overview of several key aspects of BMS requirements for stationary applications and electric vehicles, from a hardware point of view.”
BackgroundBattery voltage transfer method for multi-cells Li-ion battery pack protection chips
Wu, K., Wang, H., Chen, C., et al. (2021) · Analog Integrated Circuits and Signal Processing · doi:10.1007/s10470-021-01836-9 · Cited by 6
Maures, M., Mathieu, R., Capitaine, A., Delétage, J.-Y., Vinassa, J.-M., & Briat, O. (2022) · Batteries · doi:10.3390/batteries8050039 · Cited by 7
State and fault estimation scheme based on sliding mode observer for a Lithium-ion battery
Mohamed, M., Pierce, I., & Truong, D. Q. (2023) · Energy Reports · doi:10.1016/j.egyr.2023.05.086 · Cited by 6
Towards a Cross-Domain Modeling Approach in System-of-Systems Architectures
Brankovic, B., Binder, C., Draxler, D., et al. (2019) · Springer eBooks · doi:10.1007/978-3-030-34843-4_14 · Cited by 6
Basic principles of automotive modular battery management system design
Zaitsev, A. P., Butarovich, D. O., & Smirnov, A. A. (2020) · IOP Conference Series Materials Science and Engineering · doi:10.1088/1757-899x/819/1/012024 · Cited by 6
Mu, B.-Q., Doukhi, O., Wang, L., & Lee, D.-J. (2025) · Journal of Computational Design and Engineering · doi:10.1093/jcde/qwaf042 · Cited by 5
Shah, S. A. A., Mahrukh, Shah, S. M. A., Wang, S., Niazi, S. G., Xu, Z., & Wu, M. (2026) · Journal of Energy Storage · doi:10.1016/j.est.2026.121207 · Cited by 10
In Operando Health Monitoring for Lithium-Ion Batteries in Electric Propulsion Using Deep Learning
Vajja, J. V. R., Serov, A., Sudarshan, M., Singh, M., & Tomar, V. (2024) · Batteries · doi:10.3390/batteries10100355 · Cited by 6
Krause, F., Schweizer, F., Burger, A., Ludewig, F., Knips, M., Quade, K. L., Würsig, A., & Sauer, D. U. (2026) · Batteries · doi:10.3390/batteries12030095 · Cited by 8
“However, present condition monitoring of LIB s is limited to current, voltage and temperature measurements on the outside of the cell [6].”
Self-citationMachine Learning‐Based Management of Hybrid Energy Storage Systems in e‐Vehicles
Blessie, E. C., Jagnannathan, S. K., Krishna, B. V., et al. (2022) · Journal of Nanomaterials · doi:10.1155/2022/8270718 · Cited by 5
“With the increase in complexity of the system, the difficulty in configuration also increases [26].”
BackgroundARMoR: Amphibious Robot for Mobility in Real-World Applications
Hammond, M. G., & Lee, K. (2023) · IEEE/ASME International Conference on Advanced Intelligent Mechatronics · doi:10.1109/aim46323.2023.10196173 · Cited by 5
“This makes the robots much more reliable in unpredictable environments and reduces the chance of power loss during operation [22].”
BackgroundConceptual Implementation of LSTM-Improved LA Based Smart Electric Vehicle Battery Management System
Kumar, K., Sadhu, P. K., Farkhad, D. R., Gracious, L. A. A., Ramachandran, S., & Devi, V. C. (2023) · International Conference on Augmented Intelligence and Sustainable Systems (ICAISS) · doi:10.1109/icaiss58487.2023.10250696 · Cited by 6
“It [19] offered a summary of current advancements in cutting-edge systems and gave the reader an idea of what should be considered when building a BMS for a specific use case.”
BackgroundThermal Management for a Stadium Power Supply Container Using a Rack-Level Air Cooling Strategy
Dong, Y., Ding, Y., Elfeky, K. E., Qi, Y., Chu, W., & Wang, Q. (2024) · Energies · doi:10.3390/en17071654 · Cited by 5
Open-Circuit Voltage Variation in LiCoO2 Battery Cycled in Different States of Charge Regions
Barcellona, S., Codecasa, L., Colnago, S., & Piegari, L. (2024) · Energies · doi:10.3390/en17102364 · Cited by 5
Critical Review on Battery Management Systems
Raj, K. V., Rayudu, K., & Battapothula, G. (2022) · International Conference on Applied Artificial Intelligence and Computing (ICAAIC) · doi:10.1109/icaaic53929.2022.9793001 · Cited by 8
“a) single cell; b) cells connected in parallel; c) cells connected in series; d) parallel connected of two strings of three serially connected cells; e) series connection of three modules having two parallel cells.[7]”
BackgroundMethodInfluentialA Review on Battery Management System
Sheoran, J., Dhillon, J., & Mishra, S. (2024) · Lecture notes in electrical engineering · doi:10.1007/978-981-99-8007-9_19 · Cited by 5
Battery Management System Hardware Design for a Student Electric Racing Car
Bata, M., & Mikle, D. (2019) · IFAC-PapersOnLine · doi:10.1016/j.ifacol.2019.12.736 · Cited by 6
Multiple Sensor Fail-Operational Architecture for Electric Vehicle Powertrain Control System
Wang, Y., & Chen, R. (2021) · Electronics · doi:10.3390/electronics10111306 · Cited by 4
Study of Battery Management System using Watchdog Software
Vankadara, K., Sujitha, S., Shukla, S., Alam, S., & Sultana, Z. G. (2023) · International Conference on Innovative Practices in Technology and Management (ICIPTM) · doi:10.1109/iciptm57143.2023.10118055 · Cited by 4
“[5 ] Fig.”
False Data Injection Attack Detection Methods for Battery Stacks with Input Noise
O'Brien, V. A., Rao, V. S., & Trevizan, R. D. (2024) · IEEE Power & Energy Society Innovative Smart Grid Technologies Conference (ISGT) · doi:10.1109/isgt59692.2024.10454175 · Cited by 4
Lima, E. S., Baldo, C. R., & de Souza, C. P. G. (2024) · Journal of the Brazilian Society of Mechanical Sciences and Engineering · doi:10.1007/s40430-024-05003-9 · Cited by 5
“In fact, the battery management system performs several key functionalities, including battery state estimation, cell balancing, pack recharging and discharging control, thermal management, fault prognosis, health diagnosis, and data communication [25, 26].”
Effect of Unbalanced Cells in Lithium-ion Battery Pack Performance and SOC Estimation
Chauhan, S. R., Kumar, K., Nadarajan, S., et al. (2024) · doi:10.1109/iemecon62401.2024.10846650 · Cited by 4
“For example, as shown in Fig.4 (a There are many cells in the battery pack with series parallel combination, and many times there is uncertainty happens because of cell degradation [10].”
Strategies of battery management systems in electric vehicles: a review
Vishwakarma, V. K., Srivastava, S., & Mishra, V. (2025) · International Journal of Modelling and Simulation · doi:10.1080/02286203.2025.2523065 · Cited by 7
“Figure 2 shows how a BMS combines hardware and software to maximize battery performance [8].”
Decentralized Battery Management System with Customized Hardware Components
Reindl, A., Meier, H., Niemetz, M., et al. (2021) · IEEE Student Conference on Research and Development (SCOReD) · doi:10.1109/scored53546.2021.9652737 · Cited by 4
A Cost-Effective Passive/Active Hybrid Equalizer Circuit Design
Sun, C.-C., Chou, C.-H., Lin, Y., & Huang, Y.-H. (2022) · Energies · doi:10.3390/en15062000 · Cited by 6
Charging System for Electric Vehicles
Pant, D., Singh, N., & Gupta, P. K. (2022) · IEEE Delhi Section Conference (DELCON) · doi:10.1109/delcon54057.2022.9753117 · Cited by 7
Importance of Battery Pack Design and Battery Management Systems in Electric Vehicles
Hemavathi, S., Srinivas, S., & Prakash, A. S. (2023) · Advances in computer and electrical engineering book series · doi:10.4018/978-1-6684-6631-5.ch001 · Cited by 8
Метод відновлення акумуляторів ноутбуків в умовах обмежених ресурсів
Tetskyi, A., Perepelitsyn, A., & Zheltukhin, O. (2023) · Aerospace technic and technology · doi:10.32620/aktt.2023.5.08 · Cited by 4
Intelligent Battery Management System Integrated with Solar PV for Residential Applications
Kumar, R. S., Kathiravan, P., Bhuvaneshwaran, V., Jagadeev, G. S., Prasath, S. K., & Kumar, B. H. (2024) · International Conference on Smart Technologies for Power and Renewable Energy (SPECon) · doi:10.1109/specon61254.2024.10537311 · Cited by 4
“Focusing on the hardware components of BMSs examines their use in electric vehicles and stationary applications are examined in [4].”
BackgroundAdaptive Battery State Estimation Considering Input Noise Compensation
Trevizan, R. D., O'Brien, V. A., & Rao, V. S. (2024) · International Symposium on Power Electronics, Electrical Drives, Automation and Motion (SPEEDAM) · doi:10.1109/speedam61530.2024.10609188 · Cited by 4
“…and performance-related functions, which include cell voltage, current, and temperature data acquisition, state of charge (SoC) and state of health estimation, thermal management, cell charge balancing, enforcing safety constraints, and controlling battery module or string contactors [3], [4].”
BackgroundBattery voltage equalisation using single‐phase cascaded H‐bridge converters
Pirooz, A., Firouz, Y., Berecibar, M., & Mierlo, J. V. (2020) · IET Power Electronics · doi:10.1049/iet-pel.2020.0522 · Cited by 4
Lim, N.-G., Kim, J., & Lee, S. (2021) · Electronics · doi:10.3390/electronics10121448 · Cited by 6
Lee, S., Noh, G., & Ha, J.-I. (2021) · IEEE Applied Power Electronics Conference and Exposition (APEC) · doi:10.1109/apec42165.2021.9487069 · Cited by 4
“, cell capacities, impedances, aging, self-discharge rate, and temperature [1], [4], cells’ status become unbalanced during the operation cycle.”
BackgroundProceedings of the 11th Model-Based Enterprise Summit (MBE 2020)
Hedberg, T., & Carlisle, M. (2020) · doi:10.6028/nist.ams.100-29 · Cited by 3
Manoj, L., & Wang, P. (2025) · Annual Reliability and Maintainability Symposium (RAMS) · doi:10.1109/rams48127.2025.10935210 · Cited by 3
“Certain applications require these algorithms to be deployed onto on-board processors without the support of Internet-of-things (IoT) and cloud-based technology [3].”
Physics-Based Analysis of Cell Imbalances and Aging in Lithium-Ion Battery Modules and Packs
Ayalasomayajula, S. M., Preger, Y., Mueller, J. A., & Allu, S. (2025) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/adf66f · Cited by 7
Boumous, Z., Boumous, S., Fellah, M., Guesmi, A., & Khezami, L. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.118911 · Cited by 4
Faiz, M., Lee, M.-Y., Kang, E., Choi, H., & Jonghoon, K. (2023) · International Conference on Power Electronics and ECCE Asia (ICPE-ECCE Asia) · doi:10.23919/icpe2023-ecceasia54778.2023.10213723 · Cited by 3
“Cell connection fault is because of a loose connection of cells with terminals [6].”
BackgroundDesign of Passive Cell Balancing for 48V Lithium Batteries for EV/Drones Applications
Karunanithi, K., Ramesh, S., Raja, S. P., et al. (2023) · International Conference on Augmented Intelligence and Sustainable Systems (ICAISS) · doi:10.1109/icaiss58487.2023.10250675 · Cited by 3
“High voltage, high efficiency and long life span battery system are required by the increasing reliance on EVs, which cell for improved battery monitoring algorithms [9, 10].”
BackgroundSun, C.-C., & Lin, Y. (2024) · Engineering Research Express · doi:10.1088/2631-8695/ad6b74 · Cited by 4
O'Brien, V. A., Rao, V. S., & Trevizan, R. D. (2024) · IEEE Open Access Journal of Power and Energy · doi:10.1109/oajpe.2024.3493757 · Cited by 6
“BESSs are equipped with battery management systems (BMSs) to collect sensor measurements, estimate states, ensure operation within safe limits, and balance cell voltages within stacks [3], [4], [5], [6], [7].”
Bockrath, S., & Pruckner, M. (2023) · ACM International Conference on Future Energy Systems (e-Energy) · doi:10.1145/3575813.3595207 · Cited by 4
Topologies and control for battery balancing applications
Ma, Z., & Gao, F. (2024) · Elsevier eBooks · doi:10.1016/b978-0-323-85622-5.00008-0 · Cited by 3
Lee, S., Noh, G., & Ha, J.-I. (2021) · doi:10.1109/ecce-asia49820.2021.9479094 · Cited by 3
Velukutty, K. N. K., Sundararajan, D., Krishnappa, M. R., et al. (2025) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-025-15527-6 · Cited by 2
EV Battery Management System with Integrated Charge Monitoring and Fire Protection
Khan, M. A., Vishwakarma, V. K., Srivastava, S., Zeeshan, A., Hussain, G., Adnan, M., & Yadav, A. K. (2025) · National Conference on Electrical and Electronics Engineering (ELECO) · doi:10.1109/ice367573.2025.11448792 · Cited by 2
“New battery management rules are pertaining to minimizing risks such as overcharging, thermal runaway and premature aging, especially in safety sensitive areas like electric vehicle propulsion [3].”
Wireless Control of Smart Battery Systems
de Sousa, R. O., Kulkarni, A., Hansen, M. S., et al. (2022) · IEEE International Symposium on Power Electronics for Distributed Generation Systems (PEDG) · doi:10.1109/pedg54999.2022.9923316 · Cited by 2
Brankovic, B., Binder, C., & Neureiter, C. (2023) · SAE International Journal of Connected and Automated Vehicles · doi:10.4271/12-06-02-0014 · Cited by 2
Fault Detection in Series Battery Modules: An Integrated Approach for Micro Short Circuits
Yen, J.-F., Luo, Y., Chen, G., & Liu, C. (2024) · IEEE Wireless Power Technology Conference and Expo (WPTCE) · doi:10.1109/wptce59894.2024.10557442 · Cited by 2
“The battery management system [11, 12] is the core of the pure electric vehicle power system.”
BackgroundManoharan, A., Sooriamoorthy, D., Aparow, V. R., & Begam, M. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.115839 · Cited by 3
Intelligent Battery Management in a Hybrid Photovoltaic Using Fuzzy Logic System
Magsumbol, J.-A. V., Bandala, A. A., Culaba, A. B., Sybingco, E., Vicerra, R. R. P., Naguib, R. N. G., & Dadios, E. P. (2025) · Technologies · doi:10.3390/technologies13060214 · Cited by 3
“Current sensors track how much charge flows in and out, accurately showing battery use [21].”
Metadata
- Authors
- Lelie, M., Braun, T., Knips, M., Nordmann, H., Ringbeck, F., Zappen, H., & Sauer, D. U.
- Affiliations
- Jülich Aachen Research Alliance (DE)
- Corresponding author
- Lelie, Markus
- Venue
- Applied Sciences
- Publisher
- MDPI AG
- Published
- 2018-03-30
- Volume
- 8
- Issue
- 4
- Pages
- 534
- ISSN
- 2076-3417 (ISSN-L)
- OpenAlex
- W2795079499
- Cited by
- 287
- References
- 33
- Citations by year
- 2026: 26 · 2025: 46 · 2024: 52 · 2023: 49 · 2022: 37 · 2021: 45 · 2020: 18 · 2019: 12 · 2018: 2
- FWCI
- 10.21
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Applied Sciences (publishedVersion, cc-by)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- RWTH Publications (RWTH Aachen) (submittedVersion, other-oa)
- Funders
- European Union’s Horizon 2020 research and innovation programme (No 713771)
- German Federal Ministry of Transport and Digital Infrastructure (16SBS001C)
- Topics
- Physical Sciences › Engineering › Automotive Engineering › Battery Modeling and Management
- Physical Sciences › Engineering › Automotive Engineering › Electric and Hybrid Vehicle Technologies
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Advancements in Battery Materials
- Keywords
- battery management systems, electric vehicles, stationary energy storage, sensor measurements, battery balancing, battery safety, system reliability
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.