Battery Management System Hardware Concepts: An Overview
Open accessThe DOI matches its Crossref record; 35 of the 35 references it cites were found in a registry or an index; 2 of the 117 sources its claims cite were checked for support.
Abstract
This paper focuses on the hardware aspects of battery management systems for electric vehicle and stationary applications.
Overview
CoChat Summary
TL;DR
This paper reviews hardware concepts for battery management systems in electric vehicle and stationary applications, covering requirements, pack topologies, measurement, balancing, and safety/reliability. It illustrates these concepts with four disassembled commercial EV battery packs and compares implementation choices.
Key findings
- Voltage acquisition accuracy strongly affects SOC estimation: with ±1 mV voltage accuracy, the paper reports a base SOC error of 0.2% for NMC cells but 5.9% for LFP cells; typical BMS AFEs have about ±1 mV accuracy and 12–16 bit full scale, giving about 380 µV resolution (14-bit for BQ76PL536A).
- Observed commercial packs used passive balancing with small currents around 100 mA (balancing resistances of 30–40 Ω at an assumed 4.2 V), dissipating 387–430 mW per cell; active balancing was not observed by the authors in commercially available automotive battery packs in volume markets.
- Four EV examples are described: Mitsubishi i-MiEV with 88 prismatic cells and LTC6802G-2 per module PCB; VW e-Up with 17 modules of six series-connected cell pairs and nine MAX11068 daisy-chained via I2C; Tesla Model-S with 7104 18,650 cells in a 96s74p configuration, 16 modules, nominal 355 V, and bq76PL536A-Q1; smart fortwo electric drive with 90 pouch cells.
- Insulation monitoring standards are summarized: for DC systems a minimum insulation resistance of 100 Ω/V is recommended, for AC systems 500 Ω/V; ECE-R100 demands minimum 500 Ω/V, and DIN61557-8 allows a measuring time of at most 100 s.
Methods
- Design: narrative overview/review of BMS hardware for lithium-ion batteries, organized around requirements, topologies, measurement, balancing, and safety/reliability.
- Data/sample: four commercially available EV battery packs were disassembled and analyzed (Mitsubishi i-MiEV, smart fortwo electric drive, VW e-Up, Tesla Model-S; for Tesla only one module was available, with some data based on an AVL presentation). The paper also draws on datasheets, standards, and literature.
- Analysis: qualitative comparison of topologies, components, and implementation choices, supported by tables and figures; no new experimental performance testing is reported.
Limitations
- Stated: due to the huge variety of applications and systems, it is not possible to consider every existing facet; no manufacturer documentation was available for the remaining vehicles/batteries, so information on them is less detailed than for the i-MiEV; Tesla data are based on an AVL presentation and the authors’ analysis of a single separately purchased module.
- Stated: the BMS IC table is already outdated at the time it is printed, and not all datasheet values are easily comparable because conditions differ between suppliers.
- Evident from the text: as an overview, it does not provide a systematic quantitative review or primary experimental validation, and its real-world examples are limited to four battery packs and selected components.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
2 Valid · 17 Not valid · 89 Not checked · 160 Own results and interpretations
Every source the paper cites for this claim was checked and supports it.
In the paper
“According to [59], the main hazards inside lithium-ion battery packs are exposure to high voltage, arcing, fire, vented gas combustibility and vented gas toxicity.”
§ Battery Management System Hardware Concepts: An Overview > 6. Safety and Reliability
What the sources say
- Supportedcites [59] Rosewater, 2015, Analyzing system safety in lithium-ion grid energy storage, J. Power Sources source
The Introduction (p. 1) lists voltage, arc-flash/blast potential, fire potential, vented-gas combustibility, and vented-gas toxicity as properties of lithium-ion batteries that can develop hazardous conditions. It notes that the list is not comprehensive, but it directly supports the five hazards named in the claim. (LLM, conf=0.92)
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“if a ±1 mV voltage accuracy system is used to calculate the SOC on NMC type lithium cells, then a base error of 0.2 % can be expected.”
§ Battery Management System Hardware Concepts: An Overview > 2.2. Voltage Acquisition
plainstates a possible cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“If the same acquisition mimic is used to acquire an LFP cell's SOC, then a base error of 5.9 % has to be expected.”
§ Battery Management System Hardware Concepts: An Overview > 2.2. Voltage Acquisition
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Case 1: Using a series connection of m times n parallel cells, m voltage channels would be needed.(see Figure 2e)”
§ Battery Management System Hardware Concepts: An Overview > 3. Topologies of BMS
hedgedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Case 2: Using a parallel connection of n strings of m cells in series, m • n voltage measurement channels would be needed.(see Figure 2d)”
§ Battery Management System Hardware Concepts: An Overview > 3. Topologies of BMS
hedgedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
90 more claims
Create a free account to see all 268 claims and to verify the 50 references still open.
- It may state two separate claims as one. 82
- Probably not a substantial claim. 133
- The quote only partly states this claim. 11
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Battery Management System Hardware Concepts: An Overview > Example (1) Mitsubishi i-MiEV
“The PCB on top of the modules is called the Cell Management Unit (CMU) in the official service manual for the car [30].”
§ Battery Management System Hardware Concepts: An Overview > References
“30. Sensitec. CDS4150 MagnetoResistive Current Sensor. Technical Report, 2016.”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Battery Management System Hardware Concepts: An Overview > 4.1.2. Contactless Current Sensors
“One of the main disadvantages of the Hall effect based sensors is their limited bandwidth-usually not higher than a few ten kHz”
§ Battery Management System Hardware Concepts: An Overview > 4.1.2. Contactless Current Sensors
“such as Allegro Microsystems' A136x product family (Worcester, MA, USA) [37] (120 kHz) or LEM's LTC200 series sensors (100 kHz) [38]”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Battery Management System Hardware Concepts: An Overview > Example (4) Tesla Model-S
“According to [29], the whole battery consists of 7104 single 18,650 cells”
§ Battery Management System Hardware Concepts: An Overview > References
“29. Pettigrew, W. Selecting the Most Effective Current Sensing Technology. Power Electron. Eur. 2007, 8, 27-31.”
Citations
Cites
Waag, W., Fleischer, C., & Sauer, D. U. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2014.02.064 · Cited by 1,059 · cited 1×
“To overcome the resulting problems for SOC estimation, there are approaches using algorithms and parametrised models to combine the available data and retrieve usable values [12], which however is beyond the scope of this work.”
MethodSelf-citationCurrent Sensing Techniques: A Review
Ziegler, S., Woodward, R. C., Iu, H. H.-C., & Borle, L. J. (2009) · IEEE Sensors Journal · doi:10.1109/jsen.2009.2013914 · Cited by 774 · cited 3×
“The measurement range is limited by the accuracy of the voltage measurement [10,31].”
BackgroundMethodBattery equalization active methods
Gallardo-Lozano, J., Romero-Cadaval, E., Milanes-Montero, M. I., & Guerrero-Martinez, M. A. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2013.08.026 · Cited by 542 · cited 1×
“An overview of the possible topologies is given in [55,58].”
BackgroundProduction caused variation in capacity aging trend and correlation to initial cell performance
Baumhöfer, T., Brühl, M., Rothgang, S., & Sauer, D. U. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2013.08.108 · Cited by 421 · cited 2×
“[23] has reviewed the changes of different cells’ capacities in a batch of 18,650 consumer cells with the same initial capacity and that were stressed with the same load profile.”
BackgroundSelf-citationA failure modes, mechanisms, and effects analysis (FMMEA) of lithium-ion batteries
Hendricks, C., Williard, N., Mathew, S., & Pecht, M. (2015) · Journal of Power Sources · doi:10.1016/j.jpowsour.2015.07.100 · Cited by 381 · cited 1×
“Especially lithium plating at low temperatures is a serious risk, as it can lead to the formation of dendrites and subsequent internal short circuits of the cells [69].”
BackgroundInternal short circuit detection for battery pack using equivalent parameter and consistency method
Ouyang, M., Zhang, M., Feng, X., Lu, L., Li, J., He, X., & Zheng, Y. (2015) · Journal of Power Sources · doi:10.1016/j.jpowsour.2015.06.087 · Cited by 309 · cited 1×
“Some diagnostic algorithms are proposed in literature to detect internal short circuits [71,72] at early stages.”
BackgroundShang, Y., Zhang, C., Cui, N., & Guerrero, J. M. (2015) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2014.2345672 · Cited by 281 · cited 3×
“(a) causes for the imbalance of several battery cells, figure based on [57]; (b) categorization of different balancing methods, shown names of non-dissipative methods refer to the direction of energy transfer, figure based on [55].”
BackgroundHandbuch Lithium-Ionen-Batterien
(2013) · doi:10.1007/978-3-642-30653-2 · Cited by 252
Instantaneous measurement of the internal temperature in lithium-ion rechargeable cells
Srinivasan, R., Carkhuff, B. G., Butler, M. H., & Baisden, A. C. (2011) · Electrochimica Acta · doi:10.1016/j.electacta.2011.03.136 · Cited by 218
Sensorless battery temperature measurements based on electrochemical impedance spectroscopy
Raijmakers, L. H. J., Danilov, D. L., van Lammeren, J. P. M., Lammers, M. J. G., & Notten, P. H. L. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2013.09.005 · Cited by 203
Ecker, M., Shafiei Sabet, P., & Sauer, D. U. (2017) · Applied Energy · doi:10.1016/j.apenergy.2017.08.034 · Cited by 181 · cited 1×
“For avoiding lithium plating, temperature, voltage and current must be known precisely [6].”
BackgroundSelf-citationLiu, Z., Ahmed, Q., Zhang, J., Rizzoni, G., & He, H. (2016) · Control Engineering Practice · doi:10.1016/j.conengprac.2016.03.015 · Cited by 90 · cited 1×
“Other types of faults, for example defective sensors, can be detected by appropriate diagnostic algorithms [75].”
BackgroundAnalyzing system safety in lithium-ion grid energy storage
Rosewater, D., & Williams, A. (2015) · Journal of Power Sources · doi:10.1016/j.jpowsour.2015.09.068 · Cited by 77 · cited 1×
“According to [59], the main hazards inside lithium-ion battery packs are exposure to high voltage, arcing, fire, vented gas combustibility and vented gas toxicity.”
BackgroundBrand, M., Gläser, S., Geder, J., Menacher, S., Obpacher, S., Jossen, A., & Quinger, D. (2013) · World Electric Vehicle Journal · doi:10.3390/wevj6030572 · Cited by 68
Brand, M., Glaser, S., Geder, J., Menacher, S., Obpacher, S., Jossen, A., & Quinger, D. (2013) · 2013 World Electric Vehicle Symposium and Exhibition (EVS27) · doi:10.1109/evs.2013.6914893 · Cited by 59
High-voltage battery management systems (BMS) for electric vehicles
Hauser, A., & Kuhn, R. (2015) · Advances in Battery Technologies for Electric Vehicles · doi:10.1016/b978-1-78242-377-5.00011-x · Cited by 50 · cited 1×
“The fact that the sum of the individual cell voltages must be identical to the total pack voltage can be used as a plausibility criterion [41].”
Schmidt, J. P., Weber, A., & Ivers-Tiffée, E. (2015) · Journal of Power Sources · doi:10.1016/j.jpowsour.2014.10.163 · Cited by 43 · cited 1×
“[56] has analysed the self-discharge behaviour of commercial pouch cells by Kokam.”
BackgroundTietze, U., Schenk, C., & Gamm, E. (2012) · doi:10.1007/978-3-642-31026-3 · Cited by 39
Guidelines on Lithium-Ion Battery Use in Space Applications
McKissock, B. I., Loyselle, P. L., & Vogel, E. (2013) · NASA Technical Reports Server (NASA) · Cited by 35
(2002) · Cited by 23
Study of Insulation Monitoring Device for DC System Based on Multi-switch Combination
Jiang, J., & Ji, H. (2009) · 2009 Second International Symposium on Computational Intelligence and Design · doi:10.1109/iscid.2009.115 · Cited by 21 · cited 1×
“A slightly different system is presented in [78].”
BackgroundA novel insulation resistance monitoring device for Hybrid Electric Vehicle
Zhen-jun, W., & Li-fang, W. (2008) · 2008 IEEE Vehicle Power and Propulsion Conference · doi:10.1109/vppc.2008.4677682 · Cited by 18 · cited 1×
“[79] presents a quite simple solution that uses only one switch.”
Background(2010) · Cited by 18
Elektrische Messtechnik: Analoge, digitale und computergestützte Verfahren
Lerch, R. (2012) · Springer-Lehrbuch · doi:10.1007/978-3-642-22609-0 · Cited by 18
(2013) · University of Twente Research Information · Cited by 16
Thermal Fault-Detection Method and Analysis of Peripheral Systems for Large Battery Packs
Nordmann, H., Frisch, M., & Sauer, D. U. (2018) · Measurement · doi:10.1016/j.measurement.2017.09.031 · Cited by 16 · cited 1×
“New methods to acquire temperature along wire harnesses within complex electrical systems can also be utilized to add safety [67].”
MethodSelf-citationResearch on insulation resistance on-line monitoring for electric vehicle
Li, J., Wu, Z., Fan, Y., Wang, Y., & Jiang, J. (2005) · 2005 International Conference on Electrical Machines and Systems · doi:10.1109/icems.2005.202650 · Cited by 10
Srinivasan, R., Carkhuff, B. G., Butler, M. H., Baisden, A. C., & Uy, O. M. (2011) · Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE · doi:10.1117/12.884691 · Cited by 9
Lithium-Ion Batteries for Space
Spurrett, R., Thwaite, C., Slimm, M., et al. (2002) · Cited by 7
Study of Insulation Monitoring Device for DC System Based on Four-Switch Combination
Jiang, J., & Ji, H. W. (2009) · International Conference on Computational Intelligence and Software Engineering (CiSE) · doi:10.1109/cise.2009.5363460 · Cited by 6
The new DC system insulation monitoring device based on phase differences of magnetic modulation
Yin, G., Liu, Y., Xu, H., Li, M., & Li, J. (2012) · 2012 International Conference on Systems and Informatics (ICSAI2012) · doi:10.1109/icsai.2012.6223065 · Cited by 5 · cited 1×
“[76] measures common mode currents using a toroidal coil, which is externally excited with an alternating signal.”
Method(2012) · RWTH Publications (RWTH Aachen) · Cited by 1
Self-citationSinhuber, P., & Sauer, D. U. (2009) · RWTH Publications (RWTH Aachen) · Cited by 1
Self-citationBecker, J., Lelie, M., Jansen, M., & Sauer, D. U. (2014) · RWTH Publications (RWTH Aachen) · Cited by 1
Self-citationNordmann, H., Zappen, H., & Sauer, D. U. (2013) · RWTH Publications (RWTH Aachen) · Cited by 1
Self-citation
Research works printed but not linked: 7
- Korthauer, R. (2013). Sensorik/Messtechnik. Handbuch lithium-ionen-Batterien, Springer. Chapter 11. · DOI · Paper page
- Korthauer, R. (2013). Relais, Kontaktoren, Kabel und Steckverbinder. Handbuch lithium-ionen-Batterien, Springer. Chapter 12. · DOI · Paper page
- Könekamp, A., and Hennige, V. (2015, January 26–29). The Tesla Model S Battery: A Pack Analysis Study. Proceedings of the Advanced Automotive & Stationary Battery Conference, Mainz, Germany.
- Pettigrew, 2007, Selecting the Most Effective Current Sensing Technology, Power Electron. Eur., 8, 27
- Institute of Electrical and Electronics Engineers (1998). IEEE Guide for the Protection of Stationary Battery Systems, Institute of Electrical and Electronics Engineers.
- Lelie, M., and Sauer, D.U. (2016, January 25–27). Approach to a “Wireless”, Cell Integrated Battery Management System. Proceedings of the Kraftwerk Batterie—Advanced Battery Power Conference 2016, Münster, Germany.
- Bolsinger, C., Brix, J., and Dragan, M. (2016, January 25–27). High Frequency Model of lithium-ion Batteries for Powerline Communication. Proceedings of the Kraftwerk Batterie—Advanced Battery Power Conference 2016, Münster, Germany.
Cited by
Li, W., Rentemeister, M., Badeda, J., Jöst, D., Schulte, D., & Sauer, D. U. (2020) · Journal of Energy Storage · doi:10.1016/j.est.2020.101557 · Cited by 582
Self-citationReview of Battery Management Systems (BMS) Development and Industrial Standards
Gabbar, H., Othman, A., & Abdussami, M. (2021) · Technologies · doi:10.3390/technologies9020028 · Cited by 480
“In [6], authors discussed the battery management system hardware concepts.”
BackgroundKumar, R. R., Bharatiraja, C., Udhayakumar, K., Devakirubakaran, S., Sekar, K. S., & Mihet-Popa, L. (2023) · IEEE Access · doi:10.1109/access.2023.3318121 · Cited by 471
Hossain Lipu, M. S., Hannan, M. A., Karim, T. F., Hussain, A., Saad, M. H. M., Ayob, A., Miah, M. S., & Indra Mahlia, T. M. (2021) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2021.126044 · Cited by 446
A review on various temperature-indication methods for Li-ion batteries
Raijmakers, L. H. J., Danilov, D. L., Eichel, R.-A., & Notten, P. H. L. (2019) · Applied Energy · doi:10.1016/j.apenergy.2019.02.078 · Cited by 424
Metadata
- Authors
- Lelie, M., Braun, T., Knips, M., Nordmann, H., Ringbeck, F., Zappen, H., & Sauer, D. U.
- Affiliations
- Jülich Aachen Research Alliance (DE)
- Corresponding author
- Lelie, Markus
- Venue
- Applied Sciences
- Publisher
- MDPI AG
- Published
- 2018-03-30
- Volume
- 8
- Issue
- 4
- Pages
- 534
- ISSN
- 2076-3417 (ISSN-L)
- OpenAlex
- W2795079499
- Cited by
- 287
- References
- 33
- Citations by year
- 2026: 26 · 2025: 46 · 2024: 52 · 2023: 49 · 2022: 37 · 2021: 45 · 2020: 18 · 2019: 12 · 2018: 2
- FWCI
- 10.21
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Applied Sciences (publishedVersion, cc-by)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- RWTH Publications (RWTH Aachen) (submittedVersion, other-oa)
- Funders
- European Union’s Horizon 2020 research and innovation programme (No 713771)
- German Federal Ministry of Transport and Digital Infrastructure (16SBS001C)
- Topics
- Physical Sciences › Engineering › Automotive Engineering › Battery Modeling and Management
- Physical Sciences › Engineering › Automotive Engineering › Electric and Hybrid Vehicle Technologies
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Advancements in Battery Materials
- Keywords
- battery management systems, electric vehicles, stationary energy storage, sensor measurements, battery balancing, battery safety, system reliability
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.