Battery Management System Hardware Concepts: An Overview
Open accessThe DOI matches its Crossref record; 35 of the 35 references it cites were found in a registry or an index; 2 of the 117 sources its claims cite were checked for support.
Abstract
This paper focuses on the hardware aspects of battery management systems for electric vehicle and stationary applications.
Overview
CoChat Summary
TL;DR
This paper reviews hardware concepts for battery management systems in electric vehicle and stationary applications, covering requirements, pack topologies, measurement, balancing, and safety/reliability. It illustrates these concepts with four disassembled commercial EV battery packs and compares implementation choices.
Key findings
- Voltage acquisition accuracy strongly affects SOC estimation: with ±1 mV voltage accuracy, the paper reports a base SOC error of 0.2% for NMC cells but 5.9% for LFP cells; typical BMS AFEs have about ±1 mV accuracy and 12–16 bit full scale, giving about 380 µV resolution (14-bit for BQ76PL536A).
- Observed commercial packs used passive balancing with small currents around 100 mA (balancing resistances of 30–40 Ω at an assumed 4.2 V), dissipating 387–430 mW per cell; active balancing was not observed by the authors in commercially available automotive battery packs in volume markets.
- Four EV examples are described: Mitsubishi i-MiEV with 88 prismatic cells and LTC6802G-2 per module PCB; VW e-Up with 17 modules of six series-connected cell pairs and nine MAX11068 daisy-chained via I2C; Tesla Model-S with 7104 18,650 cells in a 96s74p configuration, 16 modules, nominal 355 V, and bq76PL536A-Q1; smart fortwo electric drive with 90 pouch cells.
- Insulation monitoring standards are summarized: for DC systems a minimum insulation resistance of 100 Ω/V is recommended, for AC systems 500 Ω/V; ECE-R100 demands minimum 500 Ω/V, and DIN61557-8 allows a measuring time of at most 100 s.
Methods
- Design: narrative overview/review of BMS hardware for lithium-ion batteries, organized around requirements, topologies, measurement, balancing, and safety/reliability.
- Data/sample: four commercially available EV battery packs were disassembled and analyzed (Mitsubishi i-MiEV, smart fortwo electric drive, VW e-Up, Tesla Model-S; for Tesla only one module was available, with some data based on an AVL presentation). The paper also draws on datasheets, standards, and literature.
- Analysis: qualitative comparison of topologies, components, and implementation choices, supported by tables and figures; no new experimental performance testing is reported.
Limitations
- Stated: due to the huge variety of applications and systems, it is not possible to consider every existing facet; no manufacturer documentation was available for the remaining vehicles/batteries, so information on them is less detailed than for the i-MiEV; Tesla data are based on an AVL presentation and the authors’ analysis of a single separately purchased module.
- Stated: the BMS IC table is already outdated at the time it is printed, and not all datasheet values are easily comparable because conditions differ between suppliers.
- Evident from the text: as an overview, it does not provide a systematic quantitative review or primary experimental validation, and its real-world examples are limited to four battery packs and selected components.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
2 Valid · 17 Not valid · 89 Not checked · 160 Own results and interpretations
Every source the paper cites for this claim was checked and supports it.
In the paper
“According to [59], the main hazards inside lithium-ion battery packs are exposure to high voltage, arcing, fire, vented gas combustibility and vented gas toxicity.”
§ Battery Management System Hardware Concepts: An Overview > 6. Safety and Reliability
What the sources say
- Supportedcites [59] Rosewater, 2015, Analyzing system safety in lithium-ion grid energy storage, J. Power Sources source
The Introduction (p. 1) lists voltage, arc-flash/blast potential, fire potential, vented-gas combustibility, and vented-gas toxicity as properties of lithium-ion batteries that can develop hazardous conditions. It notes that the list is not comprehensive, but it directly supports the five hazards named in the claim. (LLM, conf=0.92)
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“if a ±1 mV voltage accuracy system is used to calculate the SOC on NMC type lithium cells, then a base error of 0.2 % can be expected.”
§ Battery Management System Hardware Concepts: An Overview > 2.2. Voltage Acquisition
plainstates a possible cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“If the same acquisition mimic is used to acquire an LFP cell's SOC, then a base error of 5.9 % has to be expected.”
§ Battery Management System Hardware Concepts: An Overview > 2.2. Voltage Acquisition
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Case 1: Using a series connection of m times n parallel cells, m voltage channels would be needed.(see Figure 2e)”
§ Battery Management System Hardware Concepts: An Overview > 3. Topologies of BMS
hedgedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Case 2: Using a parallel connection of n strings of m cells in series, m • n voltage measurement channels would be needed.(see Figure 2d)”
§ Battery Management System Hardware Concepts: An Overview > 3. Topologies of BMS
hedgedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
90 more claims
Create a free account to see all 268 claims and to verify the 50 references still open.
- It may state two separate claims as one. 82
- Probably not a substantial claim. 133
- The quote only partly states this claim. 11
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Battery Management System Hardware Concepts: An Overview > Example (1) Mitsubishi i-MiEV
“The PCB on top of the modules is called the Cell Management Unit (CMU) in the official service manual for the car [30].”
§ Battery Management System Hardware Concepts: An Overview > References
“30. Sensitec. CDS4150 MagnetoResistive Current Sensor. Technical Report, 2016.”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Battery Management System Hardware Concepts: An Overview > 4.1.2. Contactless Current Sensors
“One of the main disadvantages of the Hall effect based sensors is their limited bandwidth-usually not higher than a few ten kHz”
§ Battery Management System Hardware Concepts: An Overview > 4.1.2. Contactless Current Sensors
“such as Allegro Microsystems' A136x product family (Worcester, MA, USA) [37] (120 kHz) or LEM's LTC200 series sensors (100 kHz) [38]”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Battery Management System Hardware Concepts: An Overview > Example (4) Tesla Model-S
“According to [29], the whole battery consists of 7104 single 18,650 cells”
§ Battery Management System Hardware Concepts: An Overview > References
“29. Pettigrew, W. Selecting the Most Effective Current Sensing Technology. Power Electron. Eur. 2007, 8, 27-31.”
Citations
Cites
Waag, W., Fleischer, C., & Sauer, D. U. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2014.02.064 · Cited by 1,059 · cited 1×
“To overcome the resulting problems for SOC estimation, there are approaches using algorithms and parametrised models to combine the available data and retrieve usable values [12], which however is beyond the scope of this work.”
MethodSelf-citationCurrent Sensing Techniques: A Review
Ziegler, S., Woodward, R. C., Iu, H. H.-C., & Borle, L. J. (2009) · IEEE Sensors Journal · doi:10.1109/jsen.2009.2013914 · Cited by 774 · cited 3×
“The measurement range is limited by the accuracy of the voltage measurement [10,31].”
BackgroundMethodBattery equalization active methods
Gallardo-Lozano, J., Romero-Cadaval, E., Milanes-Montero, M. I., & Guerrero-Martinez, M. A. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2013.08.026 · Cited by 542 · cited 1×
“An overview of the possible topologies is given in [55,58].”
BackgroundProduction caused variation in capacity aging trend and correlation to initial cell performance
Baumhöfer, T., Brühl, M., Rothgang, S., & Sauer, D. U. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2013.08.108 · Cited by 421 · cited 2×
“[23] has reviewed the changes of different cells’ capacities in a batch of 18,650 consumer cells with the same initial capacity and that were stressed with the same load profile.”
BackgroundSelf-citationA failure modes, mechanisms, and effects analysis (FMMEA) of lithium-ion batteries
Hendricks, C., Williard, N., Mathew, S., & Pecht, M. (2015) · Journal of Power Sources · doi:10.1016/j.jpowsour.2015.07.100 · Cited by 381 · cited 1×
“Especially lithium plating at low temperatures is a serious risk, as it can lead to the formation of dendrites and subsequent internal short circuits of the cells [69].”
BackgroundInternal short circuit detection for battery pack using equivalent parameter and consistency method
Ouyang, M., Zhang, M., Feng, X., Lu, L., Li, J., He, X., & Zheng, Y. (2015) · Journal of Power Sources · doi:10.1016/j.jpowsour.2015.06.087 · Cited by 309 · cited 1×
“Some diagnostic algorithms are proposed in literature to detect internal short circuits [71,72] at early stages.”
BackgroundShang, Y., Zhang, C., Cui, N., & Guerrero, J. M. (2015) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2014.2345672 · Cited by 281 · cited 3×
“(a) causes for the imbalance of several battery cells, figure based on [57]; (b) categorization of different balancing methods, shown names of non-dissipative methods refer to the direction of energy transfer, figure based on [55].”
BackgroundHandbuch Lithium-Ionen-Batterien
(2013) · doi:10.1007/978-3-642-30653-2 · Cited by 252
Instantaneous measurement of the internal temperature in lithium-ion rechargeable cells
Srinivasan, R., Carkhuff, B. G., Butler, M. H., & Baisden, A. C. (2011) · Electrochimica Acta · doi:10.1016/j.electacta.2011.03.136 · Cited by 218
Sensorless battery temperature measurements based on electrochemical impedance spectroscopy
Raijmakers, L. H. J., Danilov, D. L., van Lammeren, J. P. M., Lammers, M. J. G., & Notten, P. H. L. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2013.09.005 · Cited by 203
Research works printed but not linked: 7
- Korthauer, R. (2013). Sensorik/Messtechnik. Handbuch lithium-ionen-Batterien, Springer. Chapter 11. · DOI · Paper page
- Korthauer, R. (2013). Relais, Kontaktoren, Kabel und Steckverbinder. Handbuch lithium-ionen-Batterien, Springer. Chapter 12. · DOI · Paper page
- Könekamp, A., and Hennige, V. (2015, January 26–29). The Tesla Model S Battery: A Pack Analysis Study. Proceedings of the Advanced Automotive & Stationary Battery Conference, Mainz, Germany.
- Pettigrew, 2007, Selecting the Most Effective Current Sensing Technology, Power Electron. Eur., 8, 27
- Institute of Electrical and Electronics Engineers (1998). IEEE Guide for the Protection of Stationary Battery Systems, Institute of Electrical and Electronics Engineers.
- Lelie, M., and Sauer, D.U. (2016, January 25–27). Approach to a “Wireless”, Cell Integrated Battery Management System. Proceedings of the Kraftwerk Batterie—Advanced Battery Power Conference 2016, Münster, Germany.
- Bolsinger, C., Brix, J., and Dragan, M. (2016, January 25–27). High Frequency Model of lithium-ion Batteries for Powerline Communication. Proceedings of the Kraftwerk Batterie—Advanced Battery Power Conference 2016, Münster, Germany.
Cited by
Items 201–284 of 284
Optimal Sensor Placement for Fault Detection and Isolation in a Lunar DC Microgrid
Heyer, G., Sadabadi, K. K., D’Arpino, M., et al. (2023) · AIAA SciTech Forum · doi:10.2514/6.2023-1392 · Cited by 2
Jha, B., Adhikari, A., & Pandey, R. P. (2022) · International Conference on Sustainable Mobility Applications, Renewables and Technology (SMART) · doi:10.1109/smart55236.2022.9990552 · Cited by 2
“Lithium-ion batteries are used in various products, from cell phones and other personal electronic gadgets to the newly developing class of electric vehicles [1].”
BackgroundState of Health Estimation of an Electric Vehicle Battery Using Fusion Technology
Sravanthi, S., Lahari, A., & K, D. V. S. K. R. (2023) · International Conference on Energy, Power and Environment (ICEPE) · doi:10.1109/icepe57949.2023.10201486 · Cited by 2
“The main technological problem that must be resolved right away is the high precision health status assessment and prediction as the health of lithium batteries can be easily disturbed, change over time, and is difficult to verify [14].”
BackgroundSensors in Battery Management System for Electric Vehicles
Fei, H. (2023) · IEEE International Conference on Sensors, Electronics and Computer Engineering (ICSECE) · doi:10.1109/icsece58870.2023.10263334 · Cited by 2
“Temperature sensors are used in lead-acid battery, lithium battery, endothermic and exothermic reaction in the cell, and so on [1-4].”
MethodDesign of Battery Balancing Unit of Satellite Using BQ77PL900
Affan, M., Abdul‐Malek, Z., Sidik, M. A. B., Ali, M., Esa, M. R. M., Nawawi, Z., Munir, A., & Jambak, M. I. (2019) · doi:10.1109/icecos47637.2019.8984482 · Cited by 2
Non-nuclear based Thermoelectric + Battery System Concepts for Space Power Systems
Morgan, A. B., Kumar, J., Barklay, C. D., et al. (2020) · Proceedings - IEEE Aerospace Conference · doi:10.1109/aero47225.2020.9172493 · Cited by 2
Zheng, J., Cheng, C., Wang, D., et al. (2026) · Journal of Power Sources · doi:10.1016/j.jpowsour.2026.240024 · Cited by 1
Highly Available Li-Ion Batteries Sensors Readings Prediction Framework
Tiane, A., Alzayed, M., Okar, C., Bamati, S., & Chaoui, H. (2025) · IEEE Access · doi:10.1109/access.2025.3577133 · Cited by 1
“Additionally, malfunctioning voltage sensors can cause BHMS to incorrectly estimate critical battery performance indicators such as SOC and RUL [16].”
Design of Battery Management System for Electric Vehicle by Using LTC6804 and STM32F4
Khan, H. I., Singh, H., Tiwari, A. K., Konwar, A. P., Pati, A. K., & Ganaraj, P. S. (2025) · International Conference on Information, Implementation, and Innovation in Technology (I2ITCON) · doi:10.1109/i2itcon65200.2025.11210734 · Cited by 1
“In [2], a detailed description of development of the hardware setup for the BMS is given.”
El-Mahdy, M. H., El-Gendy, E. M., Ismael, I. M., & Saafan, M. M. (2026) · Journal of Energy Storage · doi:10.1016/j.est.2026.120794 · Cited by 8
Kim, M., Lee, M., Lim, C., & Kim, J. (2026) · Energy Technology · doi:10.1002/ente.202502646 · Cited by 1
Diers, J., & Beiranvand, H. (2026) · Communications Engineering · doi:10.1038/s44172-026-00698-1 · Cited by 1
“Johannes Diers 1 & Hamzeh Beiranvand 1,2 Individual cell surveillance in lithium-ion battery systems has not yet been widely adopted in the industry due to the increased cost of the fi nal product.”
Li, R., Liang, C., Fox, R., Jonsson, G., Goli, F., Aktas, E., & Wang, Y. (2026) · Cleaner Logistics and Supply Chain · doi:10.1016/j.clscn.2026.100348 · Cited by 1
AI/ML enabled smart battery management systems in electric vehicles
Waseem, M. (2026) · Frontiers in Batteries and Electrochemistry · doi:10.3389/fbael.2026.1883201 · Cited by 2
Elektrikli Araç Batarya Yönetim Sistemleri için Hücre Eşitleme Yöntemleri
Kaymaz, H., & HANÇAR, Y. (2021) · Akıllı Ulaşım Sistemleri ve Uygulamaları Dergisi · doi:10.51513/jitsa.897126 · Cited by 2
Temperature-Compensated Overcharge Protection Measurement Technology
Yeon, J., Noh, J. W., & Oh, I. (2023) · Advances in Science Technology and Engineering Systems Journal · doi:10.25046/aj080203 · Cited by 1
Validation Analysis of a Distributed Battery Management System Implementation : Invited Paper
Quiñones, F., Goinhex, J., & Calarco, N. (2023) · Argentine Conference on Electronics (CAE) · doi:10.1109/cae56623.2023.10086974 · Cited by 1
“The main tasks of the BMS include: the estimation and prediction of internal variables of the batteries, the charge balancing, and the thermal control, [1], [2].”
BackgroundParvathy, R. (2023) · Journal of Applied Science Engineering Technology and Management · doi:10.61779/jasetm.v1i1.7 · Cited by 1
Estimation of State of Charge for Lithium-Ion EV Battery Packs Using Passive Cell Balancing
Kumar, P., Tadikonda, N., Kumari, P., et al. (2024) · Lecture notes in electrical engineering · doi:10.1007/978-981-97-0154-4_2 · Cited by 1
Thermal Runaway Mechanism and Existing Solutions for Lithium-Ion Batteries
沈, 丹. (2024) · Journal of Advances in Physical Chemistry · doi:10.12677/japc.2024.134064 · Cited by 1
Design and Implementation of a Modular Switch Circuit Board for Dynamic Battery Reconfiguration
Mao, E., Ren, D., Zheng, X., Yv, H., Geng, C., & Han, W. (2025) · IEEE International Conference on Industrial Technology (ICIT) · doi:10.1109/icit63637.2025.10965233 · Cited by 1
Energy Management Strategy for Fuel Cell Powered Vehicle in Indian Scenario
Vishwakarma, V. K., & Srivastava, S. (2024) · International Conference on Control, Computing, Communication and Materials (ICCCCM) · doi:10.1109/iccccm61016.2024.11039987 · Cited by 1
The Model of Battery Management Considering Battery Life Based on Matrix Game
Федоренко, В. В., Samoylenko, V., Samoylenko, I. V., et al. (2020) · IEEE Conference of Russian Young Researchers in Electrical and Electronic Engineering · doi:10.1109/eiconrus49466.2020.9039051 · Cited by 1
“BMS also have a fairly large classification [10]–[12], growing intellectual capabilities The calibrate BESS is an important task in developing such systems.”
BackgroundState of Charge Equalization of Battery Modules Using Single-Phase Cascaded Multilevel Converters
Pirooz, A., Firouz, Y., & Mierlo, J. V. (2019) · International Conference on Power and Energy Systems (ICPES) · doi:10.1109/icpes47639.2019.9105524 · Cited by 1
“Imbalance SoCs between similar cells or modules within a battery pack is caused by production-related differences and different operational and environmental conditions [10].”
BackgroundMethodology and Guidelines for Designing Flexible BMS in Automotive Applications
Trongnukul, N., Fuengwarodsakul, N. H., & Masomtob, M. (2023) · Engineering Journal · doi:10.4186/ej.2023.27.7.53 · Cited by 1
“com/us/en/document/whp/ battery-management-system-tutorial [39] M.”
BackgroundComputation-efficient Approach to EIS Feature Extraction for Battery Informatics and Big DataPreprint
Quinn, X. L., Shaw, D. W., Liang, Y., et al. (2024) · ChemRxiv · doi:10.26434/chemrxiv-2024-ln7tx · Cited by 1
Qu, J., Wang, Y., Zheng, R., Li, M., & Zhang, D. (2024) · SSRN Electronic Journal · doi:10.2139/ssrn.4778973 · Cited by 1
Sensor Fault Detection and Isolation for Degrading Lithium-Ion Batteries in Electric Vehicles
Tran, M. (2020) · UWSpace (University of Waterloo) · Cited by 2
Khanaki, R. (2021) · Queensland University of Technology · doi:10.5204/thesis.eprints.208259 · Cited by 1
Ahmadian, A., Deo, A., Garg, P., & Elayyan, O. (2021) · arXiv (Cornell University) · doi:10.48550/arxiv.2104.10744
“This section in the future final report will delve into the existing architectures for hardware and software in terms of battery system controls and provides an overview of presently proposed and implemented designs [13].”
BackgroundMethodApplying the Heaviside step function to simulate the changes of temperature in automotive batteries
Zakharov, N. S., Sapozhenkov, N. O., Tyan, R. V., et al. (2021) · Journal of Physics Conference Series · doi:10.1088/1742-6596/2061/1/012001
The Investigation of Batteries and Thermal Management Systems Used in Electric Vehicles
Muhammet Yasin, K. A. B. A., Kalkan, O., & Çelen, A. (2021) · DergiPark (Istanbul University)
Speicherung der elektrischen Energie
Sauer, D. U., Kowal, J., Willenberg, L. K., et al. (2019) · Springer eBooks · doi:10.1007/978-3-662-60356-7_6
Self-citation(2022) · International Journal of Engineering Technology and Construction · doi:10.38007/ijetc.2022.030305
“In PLC testing, manual choice of experiments is as yet the most well-known strategy practically speaking [14].”
Kandaswamy, K. V., & Raj Narain, B. (2023) · Research Square · doi:10.21203/rs.3.rs-2434742/v1
"Development of a Pico-Hydro Generating System with SES-BMS for Domestic Use "
Universiti Teknologi, M. A. R. A., Azuddin, M. A., Jusoh, M. A. M., et al. (2022) · International Journal of Integrated Engineering · doi:10.30880/ijie.2022.14.05.015
Kandaswamy, K. V., & Raj Narain, B. (2023) · Research Square · doi:10.21203/rs.3.rs-2581000/v1
International Conference on Power, Control, and Sustainable Energy Systems
Boddapati, V., Prakash, D. B., & Sanjeevikumar, P. (2023) · doi:10.13052/rp-9788770229630 · Cited by 1
Shrivastav, M., & Gupta, A. (2022) · International Interdisciplinary Humanitarian Conference for Sustainability (IIHC) · doi:10.1109/iihc55949.2022.10060111
Prashar, N., & Bhadu, J. (2022) · International Interdisciplinary Humanitarian Conference for Sustainability (IIHC) · doi:10.1109/iihc55949.2022.10060209
“Some manufacturers are supplying their uninterruptible power supply with inverters that generate a perfect sine wave due to the increasing demand for UPS, especially for boilers [10].”
BackgroundKawalpreet, & Jain, M. K. (2022) · International Interdisciplinary Humanitarian Conference for Sustainability (IIHC) · doi:10.1109/iihc55949.2022.10059996
“Of course, it can be bought in the store, but we are not looking for easy ways, especially if it is not a problem to collect it [9-10].”
BackgroundIntroduction to battery systems
Kumar, P., Bansal, S., & Sonthalia, A. (2023) · Elsevier eBooks · doi:10.1016/b978-0-443-19017-9.00039-8 · Cited by 1
Blömeke, A., Zappen, H., Ringbeck, F., Wasylowski, D., & Sauer, D. U. (2023) · Research Square · doi:10.21203/rs.3.rs-3278299/v1
Self-citationBattery Management System Using IoT
Rajana, C. K. (2024) · International Journal for Research in Applied Science and Engineering Technology · doi:10.22214/ijraset.2024.61134 · Cited by 1
Perancangan Plant Automation untuk Battery Monitoring System Menggunakan Arduino Uno
Saputra, R. H., Sugiarto, K., & Lesmana, M. F. (2024) · Jurnal Teknik Elektro dan Komputasi (ELKOM) · doi:10.32528/elkom.v6i1.10062
Design of high protection liquid cooled BMS system for high voltage energy storage system
Chen, M., Shen, L., Peng, P., et al. (2024) · Journal of Physics Conference Series · doi:10.1088/1742-6596/2785/1/012001
“It cannot only improve the system response speed, but also reduce the line loss and improve the charging efficiency [4].”
BackgroundPower electronics technologies for vehicle electrification in modern power grids
Rech, C., Salvatti, G. A., Vieira, R. P., & Silva, E. C. (2024) · Elsevier eBooks · doi:10.1016/b978-0-443-13969-7.00006-0
Uğurluoğlu, A., & Karaarslan, A. (2024) · Gazi Üniversitesi Fen Bilimleri Dergisi Part C Tasarım ve Teknoloji · doi:10.29109/gujsc.1487808
Luo, Y., Yen, J.-F., & Su, W.-C. (2025) · Computer Modeling in Engineering & Sciences · doi:10.32604/cmes.2025.061180 · Cited by 2
An integrated framework for knowledge graphs based on battery management
Nagar, K., Mandloi, A., & Jain, S. (2025) · Elsevier eBooks · doi:10.1016/b978-0-443-30040-0.00013-8
Battery state of charge estimation based on variable-order battery model and ZOA-EKF
Huang, X., Wang, S., Qin, J., Zheng, W., & Wei, J. (2025) · Transportation Safety and Environment · doi:10.1093/tse/tdaf024 · Cited by 3
Sustainability Acts in Japan’s Automotive Industry
Inaba, S. (2025) · Springer eBooks · doi:10.1007/978-3-031-82857-7_14
Nayak, S. S., Jayalaxmi, H., Sathya, M., et al. (2025) · Scientia. Technology, science and society. · doi:10.59324/stss.2025.2(6).03
Battery Hazards and Safety: A Comprehensive Review for Lithium -Ion Battery System
Rawat, S., Singh, J., & Haldia, P. (2025) · International Journal of Latest Technology in Engineering Management & Applied Science · doi:10.51583/ijltemas.2025.140600008
Backhaus, J., Glockmann, M., Haffner, P., Henseleit, M., Klicker, K., Müller, K., Ockfen, M., Schmitz, D., Wegener, B., & Goertz, R. (2025) · Springer eBooks · doi:10.1007/978-3-658-47473-7_14
Battery Fault Detection Using Machine Learning: A Comprehensive Review
Saneep, K., Sundareswaran, K., Nayak, P. S. R., Simon, S. P., Josephine, R. A., & Puthusserry, G. V. (2025) · Transactions of Indian National Academy of Engineering · doi:10.1007/s41403-025-00549-z · Cited by 1
“To enhance safety, redundancy in voltage sensors and predic - tive SoC monitoring are integrated to detect and prevent overcharging events, especially in high-capacity battery packs used in electric vehicles (Lelie et al. 2018).”
Quade, K. L., Hempen, E., van den Berg, H., Jöst, D., Berger, F., Ringbeck, F., & Sauer, D. U. (2025) · Batteries & Supercaps · doi:10.1002/batt.202500456 · Cited by 1
Self-citationExternal Impacts and Assessment of Electric Vehicles: Probabilistic Risk Assessment Framework
Mustaffa, Z. B., & Budiman, B. A. (2025) · International Conference on Electric Vehicular Technology (ICEVT) · doi:10.1109/icevt67191.2025.11184091 · Cited by 1
“It may occur in lithium-ion cells due to the capacity variation of cells in the pack, incorrect voltage and current measurement, or inaccurate SOC estimation from the BMS [17].”
Simulated thermal response of a battery pack used by electric two-wheelers
Niţucă, C., Dragomir, A. O., Gabor, G., & Chiriac, G. (2025) · Thermal Science · doi:10.2298/tsci250724194n
Maier, W., Gonçalves, A. F. Q., & Machado, R. Q. (2025) · Brazilian Power Electronics Conference (COBEP) · doi:10.1109/cobep66423.2025.11231455 · Cited by 1
“0 mV [24] and is confirmed by the measurement shown in Fig.”
Smart Battery Management System for Electric Vehicles
Krishnamurthy, D., Namratha, H. J., Shreyas, V., Rohith, D. V. K., Harshitha, G. V. N., & Sindhu, D. (2025) · International Conference on Computation System and Information Technology for Sustainable Solutions (CSITSS) · doi:10.1109/csitss67709.2025.11295215
“Lelie et al. [3] present circuit-level design principles for BMS hardware, including voltage sensing, thermal feedback, and balancing circuits.”
Safe Battery Use and Grid-Convenience in an Intelligent Energy Control System
Adelt, J., Herber, P., Hurink, J. L., Niehage, M., Remke, A., & Willemsen, L. (2026) · Lecture notes of the Institute for Computer Sciences, Social Informatics and Telecommunications Engineering · doi:10.1007/978-3-032-06818-7_15
Nasri, E., Jarou, T., & Jenkal, W. (2026) · SSRN Electronic Journal · doi:10.2139/ssrn.6024655
O'Brien, V. A., & Trevizan, R. D. (2026) · IEEE Industry Applications Magazine · doi:10.1109/mias.2025.3648148
Fuzzy Logic and Neural Networks for Intelligent Battery Management Systems in Electric Vehicles
Kumar, R. S., Gajbhare, B. P., Praveen, R., Aswani, K., Bugge, B. P., & Dhivya, R. (2025) · International Conference for Advancement in Technology (ICONAT) · doi:10.1109/iconat66879.2025.11362439
“This paper defines physical measuring methodologies and safety protocols in battery management systems, highlighting hardware design and structures [2].”
Monajjemi, M., Mollaamin, F., Mojri, A., et al. (2026) · Biointerface Research in Applied Chemistry · doi:10.33263/briac161.038
Analysing the Loss of a DC-DC Converter for a Real-Time Electric Vehicle
Prasath, M. G. H., & S.BaghyaShree (2025) · International Conference on Science Technology Engineering and Mathematics (ICONSTEM) · doi:10.1109/iconstem65670.2025.11374714
“The author in [22] recommended a unidirectional active bridge to prevent excessive voltage [2].”
Anomaly Detection for Battery Systems Based on a Physics-Data-Driven Fusion Model
Chen, Z., Yan, C., Ji, X., et al. (2025) · IEEE Conference on Energy Internet and Energy System Integration (EI2) · doi:10.1109/ei268505.2025.11425254
“In the EV domain, battery systems engage in constant coordination with external components, such as charging stations, onboard computers, and electric motors, utilizing vital interfaces like Battery Management Systems (BMS), inverters, and charging ports[1].”
Power electronics in electric vehicles
Ahmad, H., Gulzar, M. M., Ahmed, M. M. R., Sharaf, A. M., Ahmed, I., & Khalid, M. (2026) · Elsevier eBooks · doi:10.1016/b978-0-323-95045-9.00013-5
Rana, K., & Natraj, N. A. (2026) · AIP conference proceedings · doi:10.1063/5.0317109
Dual-Source Energy Management Strategy for Electric Vehicles: Battery and Fuel Cell Approach
Siddula, S., Archana, D., Poojitha, B., et al. (2025) · doi:10.1109/ice367573.2025.11448823
“The EMS determines how and when the gas cell must be activated to help the battery by using FLC[2],[4],[6],[13], making sure that the hybrid device operates effectively without compromising using overall performance or thing longevity.”
Detection of Electrical Abuse in EV Lib Cells
Nenadic, N. G., Kohrt, E., & Mthetwa, M. (2026) · REMADE Circular Economy Technology Summit & Conference · doi:10.65569/isgu1467
Electrical Aircraft Engine Systems and an Economic Cost–Benefit Analysis
Raoofi, T., & Ölçen, O. (2026) · Sustainable aviation · doi:10.1007/978-3-032-15097-4_4
Battery Management System for Industrial Applications
Bhatkhedkar, A. M., Dhumal, M. B., Tambekar, K. R., et al. (2026) · Lecture notes in networks and systems · doi:10.1007/978-981-95-3492-0_28
Jang, G., Kang, S., & Lee, S. W. (2026) · Electronics · doi:10.3390/electronics15101994
Design of a Hierarchical Bidirectional Active Balancing Lithium Battery Management System
Gao, Y., Ma, W., & Zhao, Z. (2026) · Lecture notes in electrical engineering · doi:10.1007/978-981-95-7576-3_50
Monajjemi, M., Mollaamin, F., & Pour, P. H. (2026) · Sensing and Imaging · doi:10.1007/s11220-026-00813-8
“It is notable voltage accuracy system used to cal - culate SOC in a Lithium iron phosphate (LFP) has a base error of 5.9%, but for cell’s SOC lithium nickel manganese cobalt oxide (NMC) cell can have different base errors [101 ].”
InfluentialMuthusamy, S., Parimala, V., Santha kumar, C., Shankar, R., SARATHKUMAR, D., Gopal, D., Subramani, S. M., Sangeetha, S. R., & Ali, M. F. B. (2026) · International Conference on Electrical and Electronics for Sustainable Innovations (ICEESI) · doi:10.1109/iceesi68020.2026.11582934
“Lelie et al. (2018) Performance and safety standards of the electrochemical have been recorded also.”
Battery Management System in Autonomous Surface Vehicles for Water Quality Monitoring
Mady, M., Johnson, P., & Luis, S. Y. (2026) · International Conference on Machine Intelligence and Smart Innovation (ICMISI) · doi:10.1109/icmisi69868.2026.11583996
“This can be accomplished by keeping an eye on and managing the battery's charging and draining processes [4].”
Ali, F., Amin, U., Lin, Z., & Yin, Y. (2026) · Processes · doi:10.3390/pr14152445
Rohman, Y. F., Ashlah, M. B., Tu, C.-Y., Sobhita, R. A., & Sean, W. (2026) · International Conference on Smart Mechatronics (ICSMech) · doi:10.1109/icsmech69390.2026.11647146
“The divider uses R_high = 240 kΩ and R_low = 10 kΩ (ratio 1:25), yielding a maximum ADC input of 2.4 V, safely below saturation and with margin for transient spikes [13].”
InfluentialMulti-Objective Performance Optimization Design of Batteries Using Response Surface Methodology
Lin, F.-H., Shieh, J., & SIRIKAN, P. (2026) · Electronics · doi:10.3390/electronics15173939
Kiros, M., Yeneneh, K., & Sufe, G. (2026) · Applied Energy · doi:10.1016/j.apenergy.2026.128796
Metadata
- Authors
- Lelie, M., Braun, T., Knips, M., Nordmann, H., Ringbeck, F., Zappen, H., & Sauer, D. U.
- Affiliations
- Jülich Aachen Research Alliance (DE)
- Corresponding author
- Lelie, Markus
- Venue
- Applied Sciences
- Publisher
- MDPI AG
- Published
- 2018-03-30
- Volume
- 8
- Issue
- 4
- Pages
- 534
- ISSN
- 2076-3417 (ISSN-L)
- OpenAlex
- W2795079499
- Cited by
- 287
- References
- 33
- Citations by year
- 2026: 26 · 2025: 46 · 2024: 52 · 2023: 49 · 2022: 37 · 2021: 45 · 2020: 18 · 2019: 12 · 2018: 2
- FWCI
- 10.21
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Applied Sciences (publishedVersion, cc-by)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- RWTH Publications (RWTH Aachen) (submittedVersion, other-oa)
- Funders
- European Union’s Horizon 2020 research and innovation programme (No 713771)
- German Federal Ministry of Transport and Digital Infrastructure (16SBS001C)
- Topics
- Physical Sciences › Engineering › Automotive Engineering › Battery Modeling and Management
- Physical Sciences › Engineering › Automotive Engineering › Electric and Hybrid Vehicle Technologies
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Advancements in Battery Materials
- Keywords
- battery management systems, electric vehicles, stationary energy storage, sensor measurements, battery balancing, battery safety, system reliability
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.