The DOI matches its Crossref record; 35 of the 35 references it cites were found in a registry or an index; 2 of the 117 sources its claims cite were checked for support.
Battery Management System Hardware Concepts: An Overview
Open accessAbstract
This paper focuses on the hardware aspects of battery management systems for electric vehicle and stationary applications.
Overview
CoChat Summary
TL;DR
This paper reviews hardware concepts for battery management systems in electric vehicle and stationary applications, covering requirements, pack topologies, measurement, balancing, and safety/reliability. It illustrates these concepts with four disassembled commercial EV battery packs and compares implementation choices.
Key findings
- Voltage acquisition accuracy strongly affects SOC estimation: with ±1 mV voltage accuracy, the paper reports a base SOC error of 0.2% for NMC cells but 5.9% for LFP cells; typical BMS AFEs have about ±1 mV accuracy and 12–16 bit full scale, giving about 380 µV resolution (14-bit for BQ76PL536A).
- Observed commercial packs used passive balancing with small currents around 100 mA (balancing resistances of 30–40 Ω at an assumed 4.2 V), dissipating 387–430 mW per cell; active balancing was not observed by the authors in commercially available automotive battery packs in volume markets.
- Four EV examples are described: Mitsubishi i-MiEV with 88 prismatic cells and LTC6802G-2 per module PCB; VW e-Up with 17 modules of six series-connected cell pairs and nine MAX11068 daisy-chained via I2C; Tesla Model-S with 7104 18,650 cells in a 96s74p configuration, 16 modules, nominal 355 V, and bq76PL536A-Q1; smart fortwo electric drive with 90 pouch cells.
- Insulation monitoring standards are summarized: for DC systems a minimum insulation resistance of 100 Ω/V is recommended, for AC systems 500 Ω/V; ECE-R100 demands minimum 500 Ω/V, and DIN61557-8 allows a measuring time of at most 100 s.
Methods
- Design: narrative overview/review of BMS hardware for lithium-ion batteries, organized around requirements, topologies, measurement, balancing, and safety/reliability.
- Data/sample: four commercially available EV battery packs were disassembled and analyzed (Mitsubishi i-MiEV, smart fortwo electric drive, VW e-Up, Tesla Model-S; for Tesla only one module was available, with some data based on an AVL presentation). The paper also draws on datasheets, standards, and literature.
- Analysis: qualitative comparison of topologies, components, and implementation choices, supported by tables and figures; no new experimental performance testing is reported.
Limitations
- Stated: due to the huge variety of applications and systems, it is not possible to consider every existing facet; no manufacturer documentation was available for the remaining vehicles/batteries, so information on them is less detailed than for the i-MiEV; Tesla data are based on an AVL presentation and the authors’ analysis of a single separately purchased module.
- Stated: the BMS IC table is already outdated at the time it is printed, and not all datasheet values are easily comparable because conditions differ between suppliers.
- Evident from the text: as an overview, it does not provide a systematic quantitative review or primary experimental validation, and its real-world examples are limited to four battery packs and selected components.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
2 Valid · 17 Not valid · 89 Not checked · 160 Own results and interpretations
Every source the paper cites for this claim was checked and supports it.
In the paper
“According to [59], the main hazards inside lithium-ion battery packs are exposure to high voltage, arcing, fire, vented gas combustibility and vented gas toxicity.”
§ Battery Management System Hardware Concepts: An Overview > 6. Safety and Reliability
What the sources say
- Supportedcites [59] Rosewater, 2015, Analyzing system safety in lithium-ion grid energy storage, J. Power Sources source
The Introduction (p. 1) lists voltage, arc-flash/blast potential, fire potential, vented-gas combustibility, and vented-gas toxicity as properties of lithium-ion batteries that can develop hazardous conditions. It notes that the list is not comprehensive, but it directly supports the five hazards named in the claim. (LLM, conf=0.92)
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“if a ±1 mV voltage accuracy system is used to calculate the SOC on NMC type lithium cells, then a base error of 0.2 % can be expected.”
§ Battery Management System Hardware Concepts: An Overview > 2.2. Voltage Acquisition
plainstates a possible cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“If the same acquisition mimic is used to acquire an LFP cell's SOC, then a base error of 5.9 % has to be expected.”
§ Battery Management System Hardware Concepts: An Overview > 2.2. Voltage Acquisition
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Case 1: Using a series connection of m times n parallel cells, m voltage channels would be needed.(see Figure 2e)”
§ Battery Management System Hardware Concepts: An Overview > 3. Topologies of BMS
hedgedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Case 2: Using a parallel connection of n strings of m cells in series, m • n voltage measurement channels would be needed.(see Figure 2d)”
§ Battery Management System Hardware Concepts: An Overview > 3. Topologies of BMS
hedgedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
90 more claims
Create a free account to see all 268 claims and to verify the 50 references still open.
- It may state two separate claims as one. 82
- Probably not a substantial claim. 133
- The quote only partly states this claim. 11
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Battery Management System Hardware Concepts: An Overview > Example (1) Mitsubishi i-MiEV
“The PCB on top of the modules is called the Cell Management Unit (CMU) in the official service manual for the car [30].”
§ Battery Management System Hardware Concepts: An Overview > References
“30. Sensitec. CDS4150 MagnetoResistive Current Sensor. Technical Report, 2016.”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Battery Management System Hardware Concepts: An Overview > 4.1.2. Contactless Current Sensors
“One of the main disadvantages of the Hall effect based sensors is their limited bandwidth-usually not higher than a few ten kHz”
§ Battery Management System Hardware Concepts: An Overview > 4.1.2. Contactless Current Sensors
“such as Allegro Microsystems' A136x product family (Worcester, MA, USA) [37] (120 kHz) or LEM's LTC200 series sensors (100 kHz) [38]”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Battery Management System Hardware Concepts: An Overview > Example (4) Tesla Model-S
“According to [29], the whole battery consists of 7104 single 18,650 cells”
§ Battery Management System Hardware Concepts: An Overview > References
“29. Pettigrew, W. Selecting the Most Effective Current Sensing Technology. Power Electron. Eur. 2007, 8, 27-31.”
Citations
Cites
Waag, W., Fleischer, C., & Sauer, D. U. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2014.02.064 · Cited by 1,059 · cited 1×
“To overcome the resulting problems for SOC estimation, there are approaches using algorithms and parametrised models to combine the available data and retrieve usable values [12], which however is beyond the scope of this work.”
MethodSelf-citationCurrent Sensing Techniques: A Review
Ziegler, S., Woodward, R. C., Iu, H. H.-C., & Borle, L. J. (2009) · IEEE Sensors Journal · doi:10.1109/jsen.2009.2013914 · Cited by 774 · cited 3×
“The measurement range is limited by the accuracy of the voltage measurement [10,31].”
BackgroundMethodBattery equalization active methods
Gallardo-Lozano, J., Romero-Cadaval, E., Milanes-Montero, M. I., & Guerrero-Martinez, M. A. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2013.08.026 · Cited by 542 · cited 1×
“An overview of the possible topologies is given in [55,58].”
BackgroundProduction caused variation in capacity aging trend and correlation to initial cell performance
Baumhöfer, T., Brühl, M., Rothgang, S., & Sauer, D. U. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2013.08.108 · Cited by 421 · cited 2×
“[23] has reviewed the changes of different cells’ capacities in a batch of 18,650 consumer cells with the same initial capacity and that were stressed with the same load profile.”
BackgroundSelf-citationA failure modes, mechanisms, and effects analysis (FMMEA) of lithium-ion batteries
Hendricks, C., Williard, N., Mathew, S., & Pecht, M. (2015) · Journal of Power Sources · doi:10.1016/j.jpowsour.2015.07.100 · Cited by 381 · cited 1×
“Especially lithium plating at low temperatures is a serious risk, as it can lead to the formation of dendrites and subsequent internal short circuits of the cells [69].”
BackgroundInternal short circuit detection for battery pack using equivalent parameter and consistency method
Ouyang, M., Zhang, M., Feng, X., Lu, L., Li, J., He, X., & Zheng, Y. (2015) · Journal of Power Sources · doi:10.1016/j.jpowsour.2015.06.087 · Cited by 309 · cited 1×
“Some diagnostic algorithms are proposed in literature to detect internal short circuits [71,72] at early stages.”
BackgroundShang, Y., Zhang, C., Cui, N., & Guerrero, J. M. (2015) · IEEE Transactions on Power Electronics · doi:10.1109/tpel.2014.2345672 · Cited by 281 · cited 3×
“(a) causes for the imbalance of several battery cells, figure based on [57]; (b) categorization of different balancing methods, shown names of non-dissipative methods refer to the direction of energy transfer, figure based on [55].”
BackgroundHandbuch Lithium-Ionen-Batterien
(2013) · doi:10.1007/978-3-642-30653-2 · Cited by 252
Instantaneous measurement of the internal temperature in lithium-ion rechargeable cells
Srinivasan, R., Carkhuff, B. G., Butler, M. H., & Baisden, A. C. (2011) · Electrochimica Acta · doi:10.1016/j.electacta.2011.03.136 · Cited by 218
Sensorless battery temperature measurements based on electrochemical impedance spectroscopy
Raijmakers, L. H. J., Danilov, D. L., van Lammeren, J. P. M., Lammers, M. J. G., & Notten, P. H. L. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2013.09.005 · Cited by 203
Research works printed but not linked: 7
- Korthauer, R. (2013). Sensorik/Messtechnik. Handbuch lithium-ionen-Batterien, Springer. Chapter 11. · DOI · Paper page
- Korthauer, R. (2013). Relais, Kontaktoren, Kabel und Steckverbinder. Handbuch lithium-ionen-Batterien, Springer. Chapter 12. · DOI · Paper page
- Könekamp, A., and Hennige, V. (2015, January 26–29). The Tesla Model S Battery: A Pack Analysis Study. Proceedings of the Advanced Automotive & Stationary Battery Conference, Mainz, Germany.
- Pettigrew, 2007, Selecting the Most Effective Current Sensing Technology, Power Electron. Eur., 8, 27
- Institute of Electrical and Electronics Engineers (1998). IEEE Guide for the Protection of Stationary Battery Systems, Institute of Electrical and Electronics Engineers.
- Lelie, M., and Sauer, D.U. (2016, January 25–27). Approach to a “Wireless”, Cell Integrated Battery Management System. Proceedings of the Kraftwerk Batterie—Advanced Battery Power Conference 2016, Münster, Germany.
- Bolsinger, C., Brix, J., and Dragan, M. (2016, January 25–27). High Frequency Model of lithium-ion Batteries for Powerline Communication. Proceedings of the Kraftwerk Batterie—Advanced Battery Power Conference 2016, Münster, Germany.
Cited by
Li, W., Rentemeister, M., Badeda, J., Jöst, D., Schulte, D., & Sauer, D. U. (2020) · Journal of Energy Storage · doi:10.1016/j.est.2020.101557 · Cited by 582
Self-citationReview of Battery Management Systems (BMS) Development and Industrial Standards
Gabbar, H., Othman, A., & Abdussami, M. (2021) · Technologies · doi:10.3390/technologies9020028 · Cited by 480
“In [6], authors discussed the battery management system hardware concepts.”
BackgroundKumar, R. R., Bharatiraja, C., Udhayakumar, K., Devakirubakaran, S., Sekar, K. S., & Mihet-Popa, L. (2023) · IEEE Access · doi:10.1109/access.2023.3318121 · Cited by 471
Hossain Lipu, M. S., Hannan, M. A., Karim, T. F., Hussain, A., Saad, M. H. M., Ayob, A., Miah, M. S., & Indra Mahlia, T. M. (2021) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2021.126044 · Cited by 446
A review on various temperature-indication methods for Li-ion batteries
Raijmakers, L. H. J., Danilov, D. L., Eichel, R.-A., & Notten, P. H. L. (2019) · Applied Energy · doi:10.1016/j.apenergy.2019.02.078 · Cited by 424
Online capacity estimation of lithium-ion batteries with deep long short-term memory networks
Li, W., Sengupta, N., Dechent, P., Howey, D., Annaswamy, A., & Sauer, D. U. (2021) · Journal of Power Sources · doi:10.1016/j.jpowsour.2020.228863 · Cited by 362
“It has a small form factor and a CUDA technology-enabled processing unit, which enables it to perform deep-learning operations, making it ideal for association with an EV ’ s BMS [49] for prognostics tasks.”
MethodSelf-citationA Review of Lithium-Ion Battery Fault Diagnostic Algorithms: Current Progress and Future Challenges
Tran, M.-K., & Fowler, M. (2020) · Algorithms · doi:10.3390/a13030062 · Cited by 300
“It may occur in Li-ion cells due to the capacity variation of cells in the pack, incorrect voltage and current measurement, or inaccurate SOC estimation from the BMS [13].”
BackgroundMethodInfluentialManoharan, A., Begam, K. M., Aparow, V. R., & Sooriamoorthy, D. (2022) · Journal of Energy Storage · doi:10.1016/j.est.2022.105384 · Cited by 293
Tran, M.-K., Panchal, S., Khang, T. D., Panchal, K., Fraser, R., & Fowler, M. (2022) · Batteries · doi:10.3390/batteries8020019 · Cited by 247
Samanta, A., Chowdhuri, S., & Williamson, S. S. (2021) · Electronics · doi:10.3390/electronics10111309 · Cited by 231
“Cell inconsistencies in a LIB pack are a common issue; thus an appropriate BMS is also indispensable for the safe and reliable operation of the LIB pack as well as every single cell of the battery pack [9,10].”
BackgroundHabib, A. K. M. A., Hasan, M. K., Issa, G. F., Singh, D., Islam, S., & Ghazal, T. M. (2023) · Batteries · doi:10.3390/batteries9030152 · Cited by 215
“The BMS study field creates more attention and increases the research scope at the academic or industrial level. concepts [16].”
BackgroundLipu, M. S. H., Mamun, A. A., Ansari, S., Miah, M. S., Hasan, K., Meraj, S. T., Abdolrasol, M. G. M., Rahman, T., Maruf, M. H., Sarker, M. R., et al. (2022) · Batteries · doi:10.3390/batteries8090119 · Cited by 209
Hossain Lipu, M. S., Ansari, S., Miah, M. S., Meraj, S. T., Hasan, K., Shihavuddin, A. S. M., Hannan, M. A., Muttaqi, K. M., & Hussain, A. (2022) · Journal of Energy Storage · doi:10.1016/j.est.2022.105752 · Cited by 193
See, K. W., Wang, G., Zhang, Y., Wang, Y., Meng, L., Gu, X., Zhang, N., Lim, K. C., Zhao, L., & Xie, B. (2022) · International Journal of Coal Science & Technology · doi:10.1007/s40789-022-00494-0 · Cited by 162
Bockrath, S., Lorentz, V., & Pruckner, M. (2022) · Applied Energy · doi:10.1016/j.apenergy.2022.120307 · Cited by 173
Development in energy storage system for electric transportation: A comprehensive review
Ahmad, F., Khalid, M., & Panigrahi, B. K. (2021) · Journal of Energy Storage · doi:10.1016/j.est.2021.103153 · Cited by 160
Klerk, M. L. D., & Saha, A. K. (2021) · IEEE Access · doi:10.1109/access.2021.3110736 · Cited by 181
“As multiple electrochemical cells are required to form a complete battery system, there are various topologies in which the cells can be connected [32].”
BackgroundBattery management solutions for li-ion batteries based on artificial intelligence
Khawaja, Y., Shankar, N., Qiqieh, I., Alzubi, J. A. A., Alzubi, O. A., Nallakaruppan, M. K., & Padmanaban, S. (2023) · Ain Shams Engineering Journal · doi:10.1016/j.asej.2023.102213 · Cited by 159
Uzair, M., Abbas, G., & Hosain, S. (2021) · World Electric Vehicle Journal · doi:10.3390/wevj12030120 · Cited by 160
“In order to avoid all these hazards, zero potential across the contactors should be maintained by a special circuit, pre-charge unit should be established, and zero switching power should be ensured during any switching action [10,14].”
BackgroundMethodInfluentialKomsiyska, L., Buchberger, T., Diehl, S., Ehrensberger, M., Hanzl, C., Hartmann, C., Hölzle, M., Kleiner, J., Lewerenz, M., Liebhart, B., et al. (2021) · Energies · doi:10.3390/en14185989 · Cited by 143
Lv, Y., Geng, X., Luo, W., Chu, T., Li, H., Liu, D., Cheng, H., Chen, J., He, X., & Li, C. (2023) · Journal of Energy Storage · doi:10.1016/j.est.2023.108389 · Cited by 146
Kosuru, V. S. R., & Venkitaraman, A. K. (2023) · World Electric Vehicle Journal · doi:10.3390/wevj14040101 · Cited by 129
“The paper [8] presented a summary of current ideas in cutting-edge systems and allowed the reader to estimate the factors that must be considered when building a BMS for a specific application.”
BackgroundTekin, M., & Karamangil, M. İ. (2024) · Journal of Energy Storage · doi:10.1016/j.est.2024.111327 · Cited by 122
Khan, N., Ooi, C. A., Alturki, A., Amir, M., Shreasth, S., & Alharbi, T. (2024) · Energy Reports · doi:10.1016/j.egyr.2024.04.041 · Cited by 142
A guide to equivalent circuit fitting for impedance analysis and battery state estimation
Santoni, F., Angelis, A. D., Moschitta, A., Carbone, P., Galeotti, M., Cinà, L., Giammanco, C., & Carlo, A. D. (2024) · Journal of Energy Storage · doi:10.1016/j.est.2023.110389 · Cited by 114
Lithium Battery Degradation and Failure Mechanisms: A State-of-the-Art Review
Menye, J. S., Camara, M. B., & Dakyo, B. (2025) · Energies · doi:10.3390/en18020342 · Cited by 142
Tran, M., & Fowler, M. W. (2019) · Batteries · doi:10.3390/batteries6010001 · Cited by 107
Fault Detection and Diagnosis of the Electric Motor Drive and Battery System of Electric Vehicles
Khaneghah, M. Z., Alzayed, M., & Chaoui, H. (2023) · Machines · doi:10.3390/machines11070713 · Cited by 138
“As shown in Figure 15, the autoencoder structure has two steps: encoder and decoder [116].”
MethodLee, H.-J., Kim, K., Park, J., Bere, G., Ochoa, J. J., & Kim, T. (2021) · IEEE Transactions on Energy Conversion · doi:10.1109/tec.2021.3061493 · Cited by 95
A Surface Temperature Estimation Method for Lithium-Ion Battery Using Enhanced GRU-RNN
Yao, Q., Lu, D. D., & Lei, G. (2022) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2022.3197927 · Cited by 104
“The commonly used temperature sensors for battery temperature measurement have the thermal properties of negative temperature coefficient (NTC) (metal oxide) or positive temperature coefficient (PTC) (semiconductor type) [5].”
MethodHe, W., Li, Z., Liu, T., Liu, Z., Guo, X., Du, J., Li, X., Sun, P., & Ming, W. (2023) · Journal of Energy Storage · doi:10.1016/j.est.2023.107868 · Cited by 102
Raoofi, T., & Yıldız, M. (2022) · Journal of Energy Storage · doi:10.1016/j.est.2022.106486 · Cited by 102
Battery energy storage system modeling: A combined comprehensive approach
Dubarry, M., Baure, G., Pastor-Fernández, C., Yu, T. F., Widanage, W. D., & Marco, J. (2018) · Journal of Energy Storage · doi:10.1016/j.est.2018.11.012 · Cited by 89
Macharia, V. M., Garg, V. K., & Kumar, D. (2023) · IET Electrical Systems in Transportation · doi:10.1049/els2.12083 · Cited by 115
Li, W., Yue, F., Ringbeck, F., Jöst, D., & Sauer, D. U. (2021) · Applied Energy · doi:10.1016/j.apenergy.2021.118114 · Cited by 79
Self-citationZhang, Y., Wik, T., Bergström, J., & Zou, C. (2023) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2023.3267124 · Cited by 85
“A typical battery management system (BMS) only measures the individual cell voltage, and the pack current, together with a few temperature sensors for each module in the pack [22].”
BackgroundA Comprehensive Review of Research Hotspots on Battery Management Systems for UAVs
Jiao, S., Zhang, G., Zhou, M., & Li, G. (2023) · IEEE Access · doi:10.1109/access.2023.3301989 · Cited by 97
“ing modules [41], [42]; while the software part mainly includes algorithms, databases, and user interfaces [43], [44].”
MethodXu, W., Wu, X., Li, Y., Wang, H., Lu, L., & Ouyang, M. (2023) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2023.113674 · Cited by 80
EV battery fault diagnostics and prognostics using deep learning: Review, challenges & opportunities
Machlev, R. (2024) · Journal of Energy Storage · doi:10.1016/j.est.2024.110614 · Cited by 85
An intelligent battery management system (BMS) with end-edge-cloud connectivity – a perspective
Mulpuri, S. K., Sah, B., & Kumar, P. (2025) · Sustainable Energy & Fuels · doi:10.1039/d4se01238k · Cited by 81
Optimized Passive Cell Balancing for Fast Charging in Electric Vehicle
Duraisamy, T., & Deepa, K. (2021) · IETE Journal of Research · doi:10.1080/03772063.2021.1886604 · Cited by 70
Berger, F., Jöst, D., Barbers, E., Quade, K. L., Wu, Z., Sauer, D. U., & Dechent, P. (2024) · eTransportation · doi:10.1016/j.etran.2024.100355 · Cited by 72
Self-citationA Battery SOC Estimation Method Based on AFFRLS-EKF
Li, M., Zhang, Y., Hu, Z., Zhang, Y., & Zhang, J. (2021) · Sensors · doi:10.3390/s21175698 · Cited by 65
“The influence of acquisition accuracy of voltage, current, and other signals on SOC estimation is discussed in the view of the hardware [10].”
BackgroundMethodReview—Thermal Safety Management in Li-Ion Batteries: Current Issues and Perspectives
Srinivasan, R., Demirev, P. A., Carkhuff, B. G., Santhanagopalan, S., Jeevarajan, J. A., & Barrera, T. P. (2020) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/abc0a5 · Cited by 61
Battery Management System Algorithm for Energy Storage Systems Considering Battery Efficiency
Lee, J. E., Kim, J.-M., Yi, J., & Won, C.-Y. (2021) · Electronics · doi:10.3390/electronics10151859 · Cited by 64
Ashok, B., Chidambaram, K., Mason, B., Ashok, S. D., Indragandhi, V., Patel, D., Wagh, A. S., Jain, A., & Kavitha, C. (2022) · Energies · doi:10.3390/en15124227 · Cited by 62
“The imbalance is imposed by either manufacturing errors or non-uniform temperature distribution among the cells [15].”
BackgroundInfluentialCyberphysical Security of Grid Battery Energy Storage Systems
Trevizan, R. D., Obert, J., Angelis, V. D., Nguyen, T. A., Rao, V. S., & Chalamala, B. R. (2022) · IEEE Access · doi:10.1109/access.2022.3178987 · Cited by 71
“…based on cell voltage and current measurements (more on SoC estimation in Section III-H) Typically, temperature sensors are used to obtain cell surface, battery pack, and battery module air temperature using negative temperature coefficient, positive temperature coefficient, or digital sensors [155].”
BackgroundMethodInfluentialA Survey on Energy Storage: Techniques and Challenges
Krichen, M., Basheer, Y., Qaisar, S. M., & Waqar, A. (2023) · Energies · doi:10.3390/en16052271 · Cited by 61
Beyond Lithium: Future Battery Technologies for Sustainable Energy Storage
Tan, A. K. X., & Paul, S. (2024) · Energies · doi:10.3390/en17225768 · Cited by 64
A smart Li-ion battery with self-sensing capabilities for enhanced life and safety
Li, Y., Wang, W., Yang, X., Fenghao, Z., Liu, S., & Lin, C. W. (2022) · Journal of Power Sources · doi:10.1016/j.jpowsour.2022.231705 · Cited by 51
Battery Management System: Threat Modeling, Vulnerability Analysis, and Cybersecurity Strategy
Murlidharan, S., Ravulakole, V., Karnati, J., et al. (2025) · IEEE Access · doi:10.1109/access.2025.3543249 · Cited by 49
“Various researchers have been investigating BMS safety and security issues [43], [46], [47], [48], [49], [50], [51], [52], [53], [54], [55], [56], [57], [58], [45], [59], [44], [58], [60], [61], [62].”
InfluentialInvestigating explainable transfer learning for battery lifetime prediction under state transitions
Lin, T., Chen, S., Harris, S. J., Zhao, T. S., Liu, Y., & Wan, J. (2024) · eScience · doi:10.1016/j.esci.2024.100280 · Cited by 50
Madani, S. S., Shabeer, Y., Nair, A. P., Fowler, M. W., Panchal, S., Ziebert, C., Chaoui, H., Dou, S. X., See, K. W., Mekhilef, S., et al. (2025) · Batteries · doi:10.3390/batteries11110426 · Cited by 64
Khan, H. F., Hanif, A., Ali, M. U., & Zafar, A. (2021) · Journal of Energy Storage · doi:10.1016/j.est.2021.102843 · Cited by 48
Challoob, A. F., Rahmat, N. A., Ramachandaramurthy, V. K., & Humaidi, A. J. (2023) · Energy Exploration & Exploitation · doi:10.1177/01445987231211943 · Cited by 60
“To exchange data with the BMS, a controlled area network bus and BMS DAS platform in the cloud are required as indicated in Figure 3 (Lelie et al., 2018; Meah et al., 2020; Svendsen et al., 2014; Yang et al., 2021).”
MethodWireless Battery Management Systems: Innovations, Challenges, and Future Perspectives
Cao, Z., Gao, W., Fu, Y., & Mi, C. C. (2024) · Energies · doi:10.3390/en17133277 · Cited by 53
“The BMS is becoming increasingly critical in the era of renewable energy, electric vehicles (EVs), and portable electronic devices, where batteries are the lifeblood of technology [1–5].”
BackgroundHong, J., Liang, F., Yang, J. H., & Du, S. (2024) · Journal of Energy Storage · doi:10.1016/j.est.2024.113234 · Cited by 55
Aiello, O. (2020) · Electronics · doi:10.3390/electronics9030510 · Cited by 39
An Enhanced Multicell-to-Multicell Battery Equalizer Based on Bipolar-Resonant LC Converter
Luo, X., Kang, L., Lu, C., Linghu, J., Lin, H., & Hu, B. (2021) · Electronics · doi:10.3390/electronics10030293 · Cited by 42
“Active methods transfer the energy from the strong cells to the weak cells by using energy storage elements, so the imbalanced energy will not be wasted and the capacity of the pack can be improved [15,19].”
BackgroundKo, Y., & Choi, W. (2021) · Electronics · doi:10.3390/electronics10060705 · Cited by 46
Impedance Based Temperature Estimation of Lithium Ion Cells Using Artificial Neural Networks
Ströbel, M., Pross-Brakhage, J., Kopp, M., & Birke, K. P. (2021) · Batteries · doi:10.3390/batteries7040085 · Cited by 38
“In addition, in most cases not every cell is equipped with a sensor, and therefore the pack design needs to be considered to detect feasible hot spots [7].”
BackgroundElectric Vehicle Battery Modelling Methods Based on State of Charge-Review
Duraisamy, T., & Deepa, K. (2020) · Journal of Green Engineering · Cited by 50
Status and Prospects of Research on Lithium-Ion Battery Parameter Identification
Li, J., Peng, Y., Wang, Q., & Liu, H. (2024) · Batteries · doi:10.3390/batteries10060194 · Cited by 37
Hardware and Software Development of an Open Source Battery Management System
Sylvestrin, G. R., Scherer, H. F., & Ando, O. H. (2021) · IEEE Latin America Transactions · doi:10.1109/tla.2021.9461844 · Cited by 31
“[13] Conforme pode ser visto, alguns trabalhos ainda que apresentem uma visão geral do BMS, estão focados nas funções de estimação de parâmetros e balanceamento, com alguns poucos que apresentam um desenvolvimento detalhado de hardware e software .”
BackgroundInfluentialMa, Z., Jia, M., Koltermann, L., Blömeke, A., Doncker, R. W. D., Li, W., & Sauer, D. U. (2023) · Journal of Energy Storage · doi:10.1016/j.est.2023.109272 · Cited by 47
Self-citationReconfigurable Power Circuits to Series or Parallel for Energy-Balanced Multicell Battery Pack
Lee, S., Noh, G., & Ha, J.-I. (2022) · IEEE Transactions on Industrial Electronics · doi:10.1109/tie.2022.3181412 · Cited by 32
“3181412 in the battery pack with both series and parallel configurations after several operation cycles due to different manufacturing processes and operating conditions [5], [6].”
BackgroundRicco, M., Meng, J., Gherman, T., et al. (2019) · Energies · doi:10.3390/en12203862 · Cited by 30
Chin, C. S., Gao, Z., Chiew, J. H. K., & Zhang, C. (2018) · Energies · doi:10.3390/en11092467 · Cited by 33
“There have been many efforts in recent years to enhance the accuracy of the SOC estimation in a battery management system (BMS) [7].”
BackgroundJöst, D., Palaniswamy, L. N., Quade, K. L., & Sauer, D. U. (2024) · Journal of Energy Storage · doi:10.1016/j.est.2024.112042 · Cited by 41
Self-citationO'Brien, V. A., Rao, V. S., & Trevizan, R. D. (2023) · IEEE Transactions on Industry Applications · doi:10.1109/tia.2023.3308548 · Cited by 31
“Considering the architecture of BMSs [5], [29], it is clear that, similar to voltage measurements, current sensors are also subject to disturbances from noise, faults, or attacks.”
BackgroundOehler, F. F., Deuschl, X., Nürnberger, K., Graule, A., Kücher, S., Roth, T., Adam, A., Li, J., Mörtel, R., & Jossen, A. (2024) · Journal of Power Sources · doi:10.1016/j.jpowsour.2024.234620 · Cited by 32
Scalable, Decentralized Battery Management System Based on Self-organizing Nodes
Reindl, A., Meier, H., & Niemetz, M. (2020) · Lecture notes in computer science · doi:10.1007/978-3-030-52794-5_13 · Cited by 27
Lee, C.-J., Kim, B., Kwon, M.-K., Nam, K., & Kang, S. (2021) · Electronics · doi:10.3390/electronics10070846 · Cited by 29
“Therefore, this technology can improve the function of BMSs for EV batteries with high voltages, which can increase user and manufacturer satisfaction [10].”
BackgroundMethodEfficient Battery Monitoring System for E-Vehicles
Senthilkumar, M., Suresh, K. P., Sekar, T. G., et al. (2021) · International Conference on Advanced Computing and Communication Systems (ICACCS) · doi:10.1109/icaccs51430.2021.9442038 · Cited by 27
Qasem, M., Haddadin, M., Yassin, Y., Ratrout, S., Chen, C., Stoyanov, S., Al‐Hallaj, S., & Krishnamurthy, M. (2025) · IEEE Transactions on Transportation Electrification · doi:10.1109/tte.2025.3527899 · Cited by 29
“The BMS consists of a central control unit, commonly known as the “primary” unit, that communicates with subordinate units, or “secondary” units, to measure critical parameters, such as voltage, temperature, and current across individual cells [33], [34].”
Dubarry, M., Tun, M., Baure, G., Matsuura, M. M., & Rocheleau, R. E. (2021) · Electronics · doi:10.3390/electronics10131593 · Cited by 24
Hardy, J., Steggall, J., & Hardy, P. (2023) · Journal of Energy Storage · doi:10.1016/j.est.2023.106931 · Cited by 24
Alamin, K. S. S., Chen, Y., Macii, E., Poncino, M., & Vinco, S. (2025) · IEEE Transactions on Vehicular Technology · doi:10.1109/tvt.2025.3565907 · Cited by 31
“The architectural framework of a BMS is organized around all hierarchy levels (i.e., cell, module, and pack), as each layer includes specialized units that perform essential monitoring and control functions to ensure efficient operation at all levels of the battery system [8].”
Tiny Machine Learning Battery State-of-Charge Estimation Hardware Accelerated
Pau, D. P., & Aniballi, A. (2024) · Applied Sciences · doi:10.3390/app14146240 · Cited by 22
Design of Battery management system for Residential applications
Pal, P., Devabalaji, K. R., & Priyadarshini, S. (2020) · International Journal of Engineering Trends and Technology · doi:10.14445/22315381/ijett-v68i3p203s · Cited by 23
Battery Management System for Unmanned Electric Vehicles with CAN BUS and Internet of Things
Pham, N. N., Leuchter, J., Pham, K. L., & Dong, Q. H. (2022) · Vehicles · doi:10.3390/vehicles4030037 · Cited by 24
Kim, M., & So, J. (2023) · Journal of Energy Storage · doi:10.1016/j.est.2023.108876 · Cited by 24
Review of Management System and State-of-Charge Estimation Methods for Electric Vehicles
Sarda, J. S., Patel, H. S., Popat, Y., Hui, K. L., & Sain, M. (2023) · World Electric Vehicle Journal · doi:10.3390/wevj14120325 · Cited by 31
“BMS hardware principles were explored in [5] by the authors.”
BackgroundMethodInfluentialNitesh, K., & Ravichandra (2021) · SN Computer Science · doi:10.1007/s42979-021-00600-0 · Cited by 19
“The fragile nature of Li-ion batteries, when compared to lead–acid, or Ni–Cd batteries, demands extensive advanced monitoring for safe operation [4].”
BackgroundAdaptive Integral Correction-Based State of Charge Estimation Strategy for Lithium-Ion Cells
Vishnu, C., & Saleem, A. (2022) · IEEE Access · doi:10.1109/access.2022.3187193 · Cited by 23
Chianese, G., Iannucci, L., Veneri, O., & Capasso, C. (2025) · Applied Energy · doi:10.1016/j.apenergy.2025.125783 · Cited by 33
Continual learning for online state of charge estimation across diverse lithium-ion batteries
Yao, J., Zheng, B., & Kowal, J. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.116086 · Cited by 24
Ströbel, M., Kumar, V., & Birke, K. P. (2023) · Batteries · doi:10.3390/batteries9090458 · Cited by 18
“As a result, the design of the pack must consider this factor to effectively detect potential hotspots [18].”
BackgroundLacock, S., du Plessis, A. A., & Booysen, M. J. (2023) · World Electric Vehicle Journal · doi:10.3390/wevj14100296 · Cited by 17
Bashir, H., Yaqoob, A., Jawaid, I., Khalid, W., Javed, M. Y., & Sultan, W. (2022) · International Conference on Energy Conservation and Efficiency (ICECE) · doi:10.1109/icece54634.2022.9758962 · Cited by 27
Low-Complexity Electrochemical-Impedance Spectroscopy for Battery Monitoring
Carbone, P., Angelis, A. D., Schoukens, J., Moschitta, A., & Santoni, F. (2022) · IEEE Transactions on Instrumentation and Measurement · doi:10.1109/tim.2022.3222478 · Cited by 19
“To optimize battery usage, charge balancing and redistribution among battery cells is performed by battery management systems (BMSs) that also guarantee safe operations [2].”
BackgroundVaghela, R., Ramani, P., Sarda, J. S., Hui, K. L., & Sain, M. (2024) · International Journal of Energy Research · doi:10.1155/2024/6488186 · Cited by 20
“The BMS is a compact electronic device that facilitates the regulation and supervision of the battery sys-tem, therefore guaranteeing both the safety and e ffi ciency of battery operations [12, 13].”
BackgroundSensing-based monitoring systems for electric vehicle battery – A review
Khan, F. I., Hossain, M. M., & Lu, G. (2025) · Measurement Energy · doi:10.1016/j.meaene.2025.100050 · Cited by 21
Verani, A., Rienzo, R. D., Nicodemo, N., Baronti, F., Roncella, R., & Saletti, R. (2023) · Electronics · doi:10.3390/electronics12051232 · Cited by 16
“The most common choice in BMSs is thermistors, i.e., resistors, the resistance of which strongly depends on the temperature, since they are easy to read, cheap, and do not require additional communications [47,49].”
Landinger, T. F., Schwarzberger, G., Hofer, G., Rose, M., & Jossen, A. (2021) · Energies · doi:10.3390/en14071851 · Cited by 20
“Since DC current and voltage measurements need to withstand electromagnetic interference (EMI) coming from the HV power lines, BMS cell monitoring circuits are usually equipped with EMI filters such as blocking capacitors [67].”
BackgroundLeonori, S., Baldini, L., Rizzi, A., & Mascioli, F. M. F. (2021) · Energies · doi:10.3390/en14217386 · Cited by 20
Battery Management Systems Topologies: Applications : Implications of different voltage levels
Popp, A., Fechtner, H., Schmuelling, B., Kremzow-Tennie, S., Scholz, T. F., & Pautzke, F. (2021) · International Conference on Power and Energy Applications (ICPEA) · doi:10.1109/icpea52760.2021.9639285 · Cited by 21
Othman, B. M., Salam, Z., & Husain, A. R. (2022) · Journal of Energy Storage · doi:10.1016/j.est.2022.104141 · Cited by 17
Advanced Battery Management Systems with Integrated Battery Electronics
Eskandari, R., Venugopal, P., & Rietveld, G. (2022) · International Power Electronics and Motion Control Conference (EPE-PEMC) · doi:10.1109/pemc51159.2022.9962868 · Cited by 18
“Batteries as energy storage are an integral and expensive part of EVs.”
BackgroundInfluentialA High-Efficiency Capacitor-Based Battery Equalizer for Electric Vehicles
Alvarez-Diazcomas, A., Estévez-Bén, A. A., Rodríguez‐Reséndiz, J., Carrillo-Serrano, R. V., & Álvarez-Alvarado, J. M. (2023) · Sensors · doi:10.3390/s23115009 · Cited by 16
“The focus on this parameter is essential if the main purpose is to adequately manage the life and performance of batteries, because an unbalanced charge can decrease battery capacity and life [18].”
Background
Metadata
- Authors
- Lelie, M., Braun, T., Knips, M., Nordmann, H., Ringbeck, F., Zappen, H., & Sauer, D. U.
- Affiliations
- Jülich Aachen Research Alliance (DE)
- Corresponding author
- Lelie, Markus
- Venue
- Applied Sciences
- Publisher
- MDPI AG
- Published
- 2018-03-30
- Volume
- 8
- Issue
- 4
- Pages
- 534
- ISSN
- 2076-3417 (ISSN-L)
- OpenAlex
- W2795079499
- Cited by
- 287
- References
- 33
- Citations by year
- 2026: 26 · 2025: 46 · 2024: 52 · 2023: 49 · 2022: 37 · 2021: 45 · 2020: 18 · 2019: 12 · 2018: 2
- FWCI
- 10.21
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Applied Sciences (publishedVersion, cc-by)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- RWTH Publications (RWTH Aachen) (submittedVersion, other-oa)
- Funders
- European Union’s Horizon 2020 research and innovation programme (No 713771)
- German Federal Ministry of Transport and Digital Infrastructure (16SBS001C)
- Topics
- Physical Sciences › Engineering › Automotive Engineering › Battery Modeling and Management
- Physical Sciences › Engineering › Automotive Engineering › Electric and Hybrid Vehicle Technologies
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Advancements in Battery Materials
- Keywords
- battery management systems, electric vehicles, stationary energy storage, sensor measurements, battery balancing, battery safety, system reliability
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.