Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review
Open accessThe DOI matches its Crossref record; 94 of the 94 references it cites were found in a registry or an index; 110 of the 346 sources its claims cite were checked for support.
Abstract
Latent heat thermal energy storage systems (LHTES) are useful for solar energy storage and many other applications, but there is an issue with phase change materials (PCMs) having low thermal conductivity. This can be enhanced with fins, metal foam, heat pipes, multiple PCMs, and nanoparticles (NPs). This paper reviews nano-enhanced PCM (NePCM) alone and with additional enhancements. Low, middle, and high temperature PCM are classified, and the achievements and limitations of works are assessed. The review is categorized based upon enhancements: solely NPs, NPs and fins, NPs and heat pipes, NPs with highly conductive porous materials, NPs and multiple PCMs, and nano-encapsulated PCMs. Both experimental and numerical methods are considered, focusing on how well NPs enhanced the system. Generally, NPs have been proven to enhance PCM, with some types more effective than others. Middle and high temperatures are lacking compared to low temperature, as well as combined enhancement studies. Al2O3, copper, and carbon are some of the most studied NP materials, and paraffin PCM is the most common by far. Some studies found NPs to be insignificant in comparison to other enhancements, but many others found them to be beneficial. This article also suggests future work for NePCM and LHTES systems.
Overview
CoChat Summary
TL;DR
This review surveys nano-enhanced phase change materials (NePCM) for latent heat thermal energy storage, covering nanoparticles used alone and combined with fins, heat pipes, porous foams, multiple PCMs, and nano-encapsulation. It concludes that nanoparticles generally enhance PCM performance, but the "best" nanoparticle is highly situational and depends on the base PCM, melting temperature, and companion enhancement.
Key findings
- Nanoparticles were effective in nearly every reviewed case, but some studies found them weak relative to other enhancements (e.g., metal foam, heat pipes, fins). Paraffin is by far the most studied PCM, and Al₂O₃, copper, and carbon are the most studied nanoparticle materials.
- Comparative nanoparticle studies report wide-ranging thermal conductivity gains at 5% mass fraction in paraffin (A82): MWCNTs 26.7%, GNPs 154.9%, ZnO 2.6%, TiO₂ 3.6%, Al₂O₃ 6.5%, and MgO 8.4% [42]. Javadi et al. found Cu best and SiO₂ worst, with 0.2 volume fraction raising thermal conductivity up to 55% and "blade"-shaped particles most efficient [45].
- Specific quantitative outcomes cited: Algarni et al. reported a 32% overall efficiency enhancement in an evacuated tube solar collector with Cu NePCM [39]; Murugan et al. found melting time lowest at 0.3 wt% MWCNTs (−30%) and solidification lowest at 0.9 wt% (−42.2%) [43]; Mahdavi et al. reduced full charge time from 2100 min to 341 min with four heat pipes and cut discharging time by 96%, at a 14% storage-capacity penalty [82]; Ma et al. raised paraffin thermal conductivity to 1.95 W/mK with Cu at 1.9% mass fraction versus 0.216 W/mK unenhanced and 1.073 W/mK with expanded graphite [90]; Yu et al. reported SiO₂ nanoparticles increasing thermal conductivity 23.2× in solid and 9.2× in liquid state [92].
- Middle- and high-temperature NePCM studies are scarce compared with low-temperature work, and combined-enhancement studies (especially NPs with multiple PCMs) are limited; only one study combining multiple PCMs and NPs was identified [93].
Methods
- Narrative literature review of experimental and numerical studies on NePCM in LHTES systems, organized by enhancement category: nanoparticles alone, NPs with fins, NPs with heat pipes, NPs with highly conductive porous materials, NPs with multiple PCMs, and nano-encapsulated PCMs.
- PCMs are classified as low (<120 °C), middle (120–300 °C), and high (>300 °C) melting temperature following Huang et al. [8]; studies are summarized in five tables (Tables 1–5) covering PCM, nanoparticle type, phase-change process, study type, and result.
- No meta-analysis or pooled quantitative synthesis is performed; findings are reported study by study.
Limitations
- Stated by the paper: middle- and high-temperature NePCM research is lacking relative to low-temperature work; combined enhancement studies are fewer than NP-alone studies; most NP-plus-fin studies are numerical, with experimental work needed; nanoparticle sinking/agglomeration and the resulting inconsistency are unresolved; and there is no strong pattern identifying the best nanoparticle across studies.
- Evident from the text: as a narrative review it provides no standardized comparison metric, so cross-study quantitative claims (e.g., percentage improvements) come from heterogeneous setups and are not directly comparable; several summarized results are drawn from conference proceedings and figures rather than uniform primary data.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures
![Figure 1 ( a ) Sensible heat, ( b ) latent heat, ( c ) thermo-chemical thermal energy storage systems (Copyright 2015 Gracia and Cabeza) [4]. Figure 1. ( a ) Sensible heat, ( b ) latent heat, ( c ) thermo-chemical thermal energy storage systems (Copyright 2015 Gracia and Cabeza) [4].](https://figures.cochat.ai/paper-figures/d8901e9309884186b909a10f81404472/nano-enhanced-phase-change-materials-in-latent-heat-thermal-energy-storage-figure-1.png)

![Figure 3 Heat pipe network schematic from Mahdavi et al. (Copyright 2016 Elsevier) [13]. Figure 3. Heat pipe network schematic from Mahdavi et al. (Copyright 2016 Elsevier) [13].](https://figures.cochat.ai/paper-figures/0ac8bbca06da46078d36a5f8254f3b1d/nano-enhanced-phase-change-materials-in-latent-heat-thermal-energy-storage-figure-3.png)
![Figure 4 LHTES system assisted by finned heat pipes (Copyright 2016 Elsevier) [16]. Figure 4. LHTES system assisted by finned heat pipes (Copyright 2016 Elsevier) [16].](https://figures.cochat.ai/paper-figures/0f04a92162694e479e8423af88716e2f/nano-enhanced-phase-change-materials-in-latent-heat-thermal-energy-storage-figure-4.png)
![Figure 5 LHTES system configuration for the study by Akhmetov et al. (Copyright 2019 International Solar Energy Society) [31]. Figure 5. LHTES system configuration for the study by Akhmetov et al. (Copyright 2019 International Solar Energy Society) [31].](https://figures.cochat.ai/paper-figures/5f6d1eb8ce6a4df58266ed3dea5bc6d3/nano-enhanced-phase-change-materials-in-latent-heat-thermal-energy-storage-figure-5.png)
![Figure 6 The graphs show little/no improvement with the addition of NPs in the Farsani et al. study (Copyright 2017 Elsevier) [34]. A 2017 numerical study by Elbahjaoui and El Qarnia used paraffin enhanced with Figure 6. ( a ) liquid fraction, ( b ) average dimensionless temperature, ( c ) maximum dimensionless tempera-ture, and ( d ) average Nusselt number in in the Farsani et al. study (Copyright 2017 Elsevier) [34].](https://figures.cochat.ai/paper-figures/caabea35380441aa805edd628dd661d7/nano-enhanced-phase-change-materials-in-latent-heat-thermal-energy-storage-figure-6.png)
![Figure 7 Liquid fractions of the different NePCMs tested over time by Javadi et al. (Copyright 2020 Javadi et al. https://creativecommons.org/licenses/by/4.0/) accessed on 18 June 2021 [45]. Figure 7. Liquid fractions of the different NePCMs tested over time by Javadi et al. (Copyright 2020 Javadi et al. https://creativecommons.org/licenses/by/4.0/) accessed on 18 June 2021 [45].](https://figures.cochat.ai/paper-figures/393ae60678174edaba6b0d0070ffad93/nano-enhanced-phase-change-materials-in-latent-heat-thermal-energy-storage-figure-7.png)
![Figure 8 The relative enhancement in thermal conductivity with the addition of NPs (Copyright 2020 Pasupathi et al. https://creativecommons.org/licenses/by/4.0/legalcode) accessed on 18 June 2021 [49]. Figure 8. The relative enhancement in thermal conductivity with the addition of NPs (Copyright 2020 Pasupathi et al. https://creativecommons.org/licenses/by/4.0/legalcode) accessed on 18 June 2021 [49].](https://figures.cochat.ai/paper-figures/17054fdc376a41c88663f713c094d801/nano-enhanced-phase-change-materials-in-latent-heat-thermal-energy-storage-figure-8.png)
![Figure 9 SEM images of ( a ) Silicon carbide, ( b ) Silver, ( c ) Pure paraffin wax, ( d ) Paraffin-SiC composite, and ( e ) Paraffin-Ag composite from Maher et al. (Copyright 2020 Elsevier) [52]. Figure 9. SEM images of ( a ) Silicon carbide, ( b ) Silver, ( c ) Pure paraffin wax, ( d ) Paraffin-SiC composite, and ( e ) Paraffin-Ag composite from Maher et al. (Copyright 2020 Elsevier) [52].](https://figures.cochat.ai/paper-figures/76ddf524bdbe4de6b011f450bc3ba406/nano-enhanced-phase-change-materials-in-latent-heat-thermal-energy-storage-figure-9.png)
![Figure 10 Fin configurations for the three cases studied by Hajizadeh et al. (Copyright 2020 Elsevier) [75]. Figure 10. Fin configurations for the three cases studied by Hajizadeh et al. (Copyright 2020 Elsevier) [75].](https://figures.cochat.ai/paper-figures/5aa3de0480414b80946862522bcd71d3/nano-enhanced-phase-change-materials-in-latent-heat-thermal-energy-storage-figure-10.png)


![Figure 13 The PCM liquid fractions at three different times with the different numbers of heat pipes. (Copyright 2019 Elsevier) [82]. Figure 13. The PCM liquid fractions at three different times with the different numbers of heat pipes. (Copyright 2019 Elsevier) [82].](https://figures.cochat.ai/paper-figures/8d0f2b208d47455bac56ed0ff45a9ddd/nano-enhanced-phase-change-materials-in-latent-heat-thermal-energy-storage-figure-13.png)
Verification
Claims the paper makes
95 Valid · 9 Not valid · 235 Not checked · 58 Own results and interpretations
Every source the paper cites for this claim was checked and supports it.
In the paper
“The higher thermal storage density, large array of PCMs, and nearly isothermal behavior of LHTES systems (shown in Figure 1b) make them more convenient than the other methods [2].”
§ Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review > 1. Introduction to Latent Heat Thermal Energy Storage
What the sources say
- Supportedcites [2] 2. Khan, Z.; Khan, Z.; Ghafoor, A. A review of performance enhancement of PCM based latent heat storage system within the context of materials, thermal stability and compatibility. Energy Convers. Manag. 2016, 115, 132-158. [CrossRef] source
The Introduction says LHS systems offer “almost isothermal operation of thermal storage/retrieval.” Section 4 likewise describes heat storage as a “nearly isothermal process.” (LLM, conf=0.95)
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
Every source the paper cites for this claim was checked and supports it.
In the paper
“The higher thermal storage density, large array of PCMs, and nearly isothermal behavior of LHTES systems (shown in Figure 1b) make them more convenient than the other methods [2].”
§ Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review > 1. Introduction to Latent Heat Thermal Energy Storage
What the sources say
- Supportedcites [2] 2. Khan, Z.; Khan, Z.; Ghafoor, A. A review of performance enhancement of PCM based latent heat storage system within the context of materials, thermal stability and compatibility. Energy Convers. Manag. 2016, 115, 132-158. [CrossRef] source
The Introduction identifies higher thermal storage density as an advantage of latent heat storage and compares the greater mass of rock (SHS) needed to store the same energy as several PCMs (LHS). It also identifies a wide range of PCMs and nearly isothermal operation, the other advantages in the citing sentence. (LLM, conf=0.93)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
Every source the paper cites for this claim was checked and supports it.
In the paper
“and the stable temperature allows nearly isothermal heating/cooling [1].”
§ Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review > 1. Introduction to Latent Heat Thermal Energy Storage
What the sources say
- Supportedcites [1] 1. Sarbu, I.; Sebarchievici, C. A comprehensive review of thermal energy storage. Sustainability 2018, 10, 191. [CrossRef] source
Section 4, “Latent-Heat or Phase-Change Storage” (page not provided), says heat is absorbed or released at almost constant temperature during phase change and describes the storage process as isothermal. This supports the claim that LHTES enables nearly isothermal heating and cooling. (LLM, conf=0.94)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
Every source the paper cites for this claim was checked and supports it.
In the paper
“The higher thermal storage density, large array of PCMs, and nearly isothermal behavior of LHTES systems (shown in Figure 1b) make them more convenient than the other methods [2].”
§ Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review > 1. Introduction to Latent Heat Thermal Energy Storage
What the sources say
- Supportedcites [2] 2. Khan, Z.; Khan, Z.; Ghafoor, A. A review of performance enhancement of PCM based latent heat storage system within the context of materials, thermal stability and compatibility. Energy Convers. Manag. 2016, 115, 132-158. [CrossRef] source
The Introduction describes latent heat storage as a promising method because PCMs are widely available, storage density is higher, and operation is almost isothermal. Section 4 likewise calls it a better choice of heat storage on the basis of its density and nearly isothermal process. (LLM, conf=0.93)
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
Every source the paper cites for this claim was checked and supports it.
In the paper
“This means that LHTES systems can take up less volume to store the same amount of energy as SHS”
§ Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review > 1. Introduction to Latent Heat Thermal Energy Storage
What the sources say
- Supportedcites [1] 1. Sarbu, I.; Sebarchievici, C. A comprehensive review of thermal energy storage. Sustainability 2018, 10, 191. [CrossRef] source
Section 4, “Latent-Heat or Phase-Change Storage,” says that latent-heat storage increases energy storage density and therefore reduces volume. Its comparison of LHS with SHS supports the claim that LHTES can use less volume for the same stored energy. (LLM, conf=0.93)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
175 more claims · 41 with their cited sources checked
Create a free account to see all 397 claims and every source verdict.
- It may state two separate claims as one. 178
- Probably not a substantial claim. 44
- The quote only partly states this claim. 13
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review > 3.1.8. Fatty Acids
“Melting and cooling rates increased with the concentration of NPs, due to increased thermal conductivity [60].”
§ Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review > 4. Conclusions
“| et al. (2020) | (54.4 • C) | Fe 2 O 3 | Melting and solidification | Experimental | melting and |”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review > 3.1.4. Paraffin with Carbons
“A 2018 study tested the melting and solidification of paraffin PCM with a melting range of 58-60 • C and MWCNTs.”
§ Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review > 4. Conclusions
“| Murugan et al. (2018) [43] | Paraffin (18-23 • C) Low | MWCNT | Melting and solidification | Experimental | up to 0.3 wt % MWCNT, solidification up to |”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review > 3.1.1. Water NePCMs with Cu
“Khodadadi and Hosseinizadeh were among the first researchers to study NePCMs, with their numerical model for water PCM enhanced with copper NPs.They studied the influence dispersion of NPs on the thermal conductivity, solidification rate, and latent heat of fusion.The latent heat of fusion was lowered, the rate of heat release was increased, and thermal conductivity was enhanced with the addition of NPs.It was concluded that NePCM was promising for thermal energy storage applications [28].”
§ Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review > References
“29. Khodadadi, J.M.; Hosseinizadeh, S.F. Nanoparticle-enhanced phase change materials (NEPCM) with great potential for improved thermal energy storage. Int. Commun. Heat Mass Transf. 2007, 34, 534-543. [CrossRef]”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review > 3.2. NePCM and Fins
“Copper oxide particles were chosen also by Li et al. [77], who examined the charging process of paraffin PCM with different sizes and configurations of Y-shaped fins.Six different cases of fins were studied.As is demonstrated in Figure 11, the fourth case, with long, thin fins alternating attachment to the outer and inner wall, was the best case.”
§ Nano-Enhanced Phase Change Materials in Latent Heat Thermal Energy Storage Systems: A Review > 4. Conclusions
“Figure: 11 Figure 11 . Figure 11.The liquid fraction in the six different cases at different times.(Copyright 2020 Elsevier) [80].”
Cited works that were retracted
Works this paper cites that were later retracted, from the retraction notices publishers deposit. Major when the notice came out before this paper was published.
A note, not an issue: for example, a cited work that was retracted only after this paper was published, which its authors could not have known.
In the paper
“…and Hosseinizadeh (2007) [28] Water (0 ◦C) Low Cu Solidification Numerical The NPs enhanced the heat transfer and solidification Jourabian and Farhadi (2015) [29] Ice (0 ◦C) Low Cu Melting Numerical (2D) NPs increased the thermal conductivity Feng et al. (2015) [30] Water (0…”
Cited work 10.1007/s12206-015-0828-0 · retracted 2021-11-02 · notice 10.1007/s12206-021-0946-9 · this paper published 2021-06-25
Citations
Cites
1 retracted
Jourabian, M., & Farhadi, M. (2015) · Journal of Mechanical Science and Technology · doi:10.1007/s12206-015-0828-0 · Cited by 50 · cited 3×
“…and Hosseinizadeh (2007) [28] Water (0 ◦C) Low Cu Solidification Numerical The NPs enhanced the heat transfer and solidification Jourabian and Farhadi (2015) [29] Ice (0 ◦C) Low Cu Melting Numerical (2D) NPs increased the thermal conductivity Feng et al. (2015) [30] Water (0…”
BackgroundInfluentialRetractedReview on thermal energy storage with phase change materials and applications
Sharma, A., Tyagi, V. V., Chen, C. R., & Buddhi, D. (2009) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2007.10.005 · Cited by 5,936 · cited 7×
“Paraffins are composed of straight chain nalkanes (CH3–(CH2)–CH3); the general formula for fatty acids is CH3(CH2)2n•COOH; salt hydrates are composed of inorganic salts and water (AB•nH2O), and metallic hydrates consist of metals with low melting points relative to most metals [9].”
BackgroundInfluentialA Comprehensive Review of Thermal Energy Storage
Sarbu, I., & Sebarchievici, C. (2018) · Sustainability · doi:10.3390/su10010191 · Cited by 1,311 · cited 9×
“Temperature change is what drives SHS, as shown in Figure 1a [1].”
BackgroundInfluentialKhan, Z., Khan, Z., & Ghafoor, A. (2016) · Energy Conversion and Management · doi:10.1016/j.enconman.2016.02.045 · Cited by 765 · cited 5×
“They also have the disadvantage of low thermal conductivity, as well as toxicity, corrosivity, instability, and flammability, while also being much more expensive than paraffin [1,2].”
BackgroundMethodInfluentialKhodadadi, J. M., & Hosseinizadeh, S. F. (2007) · International Communications in Heat and Mass Transfer · doi:10.1016/j.icheatmasstransfer.2007.02.005 · Cited by 715 · cited 1×
“…(2005) [27] Paraffin wax (67 ◦C) Low Carbon nanofibers Solidification Experimental andanalytical (1D) The nanofibers enhanced the PCM performance Khodadadi and Hosseinizadeh (2007) [28] Water (0 ◦C) Low Cu Solidification Numerical The NPs enhanced the heat transfer and…”
BackgroundPhase change materials and thermal energy storage for buildings
de Gracia, A., & Cabeza, L. F. (2015) · Energy and Buildings · doi:10.1016/j.enbuild.2015.06.007 · Cited by 688 · cited 1×
“(a) Sensible heat, (b) latent heat, (c) thermo-chemical thermal energy storage systems (Copyright 2015 Gracia and Cabeza) [4].”
BackgroundEffect of carbon nanofiber additives on thermal behavior of phase change materials
Elgafy, A., & Lafdi, K. (2005) · Carbon · doi:10.1016/j.carbon.2005.06.042 · Cited by 430 · cited 7×
“Authors PCM Melting Point (◦C) Nanoparticle Type Phase Change Process Study Case Result Elgafy and Lafdi (2005) [27] Paraffin wax (67 ◦C) Low Carbon nanofibers Solidification Experimental andanalytical (1D) The nanofibers enhanced the PCM performance Khodadadi and Hosseinizadeh (2007) [28] Water (0 ◦C) Low Cu Solidifi…”
BackgroundInfluentialNanoparticles enhanced phase change materials (NePCMs)-A recent review
Tariq, S. L., Ali, H. M., Akram, M. A., Janjua, M. M., & Ahmadlouydarab, M. (2020) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2020.115305 · Cited by 405 · cited 2×
“Even some medical applications exist, including smart textiles, which can work to either heat or cool the person depending on the need [6].”
BackgroundChieruzzi, M., Cerritelli, G. F., Miliozzi, A., & Kenny, J. M. (2013) · Nanoscale Research Letters · doi:10.1186/1556-276x-8-448 · Cited by 381 · cited 1×
“…◦C) Middle COOHfunctionalized Graphene nanoplatelets (f-GNP) Melting and solidification Experimental andnumerical (2D) f-GNPs enhance PCM at 5% concentration Chieruzzi et al. (2013) [66] NaNO3-KNO3 (223–232 ◦C) Middle SiO2, Al2O3, TiO2, and SiO2-Al2O3 Melting and solidification Experimental 1.0…”
BackgroundInfluentialJiang, Z. Y., & Qu, Z. G. (2019) · Applied Energy · doi:10.1016/j.apenergy.2019.03.043 · Cited by 380 · cited 2×
“Jiang and Qu [5] used a heat pipe in a PCM-based lithium-ion battery thermal management system, where it was found that the heat pipe increased the efficiency of the cooling system significantly.”
BackgroundQian, T., Li, J., Min, X., Guan, W., Deng, Y., & Ning, L. (2015) · Journal of Materials Chemistry A · doi:10.1039/c5ta00309a · Cited by 372 · cited 3×
“(2012) [58] Polyethylene glycol/diatomite (60.”
BackgroundInfluentialMahdi, J. M., Mohammed, H. I., Hashim, E. T., Talebizadehsardari, P., & Nsofor, E. C. (2020) · Applied Energy · doi:10.1016/j.apenergy.2019.113993 · Cited by 323 · cited 4×
“[93], no other studies exist yet that combine the multiple PCM and NP enhancement techniques.”
BackgroundMethodInfluentialTiari, S., Qiu, S., & Mahdavi, M. (2015) · Energy Conversion and Management · doi:10.1016/j.enconman.2014.10.053 · Cited by 296 · cited 2×
“There was nearly no effect from changing the number of fins attached to the heat pipes [15].”
BackgroundMethodSelf-citationMahdi, J. M., Lohrasbi, S., Ganji, D. D., & Nsofor, E. C. (2019) · Energy Conversion and Management · doi:10.1016/j.enconman.2018.11.038 · Cited by 294 · cited 3×
“[79] used a triplex tube heat exchanger for the simultaneous charging and discharging of PCM, with an outer tube of cold HTF, a middle tube of RT82 PCM with copper fins extending into it, and an inner tube of hot HTF.”
BackgroundMethodInfluentialNitrate salts doped with CuO nanoparticles for thermal energy storage with improved heat transfer
Myers, P. D., Alam, T. E., Kamal, R., Goswami, D. Y., & Stefanakos, E. (2016) · Applied Energy · doi:10.1016/j.apenergy.2015.11.045 · Cited by 192 · cited 4×
“…the system Saranprabhu and Rajan (2019) [69] NaNO3-KNO3 (250 ◦C) Middle MgO Melting and solidification Experimental 0.25 wt % was the best concentration of MgO Myers et al. (2016) [70] KNO3, NaNO3, KNO3-NaNO3 Eutectic (334 ◦C, 306 ◦C, and 222 ◦C) Middle and High CuO Melting Experimental All…”
BackgroundInfluentialLi, W. Q., Guo, S. J., Tan, L., Liu, L. L., & Ao, W. (2021) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2020.120737 · Cited by 192 · cited 2×
“Lower porosity foam had higher effective thermal conductivity and lower wall temperature [23].”
BackgroundMethodGhalambaz, M., Doostani, A., Chamkha, A. J., & Ismael, M. A. (2017) · International Journal of Mechanical Sciences · doi:10.1016/j.ijmecsci.2017.09.045 · Cited by 188 · cited 4×
“…successful at enhancing the system Maher et al. (2021) [52] Paraffin wax (≈52 ◦C) Low SiC and Ag Melting Experimental SiC enhanced at 15 wt % showed best results Ghalambaz et al. (2017) [53] Octadecane Paraffin (30 ◦C) Low Hybrid NPs Melting Numerical (2D) Large conductivity and low…”
BackgroundInfluentialMelting process of nanoparticle enhanced PCM through storage cylinder incorporating fins
Li, F., Almarashi, A., Jafaryar, M., Hajizadeh, M. R., & Chu, Y.-M. (2021) · Powder Technology · doi:10.1016/j.powtec.2020.12.026 · Cited by 184 · cited 3×
“Longer, thinner fins allowed for natural convection, accelerating the melting [77].”
BackgroundMethodInfluentialPasupathi, M. K., Alagar, K., P, M. J. S., M.M, M., & Aritra, G. (2020) · Energies · doi:10.3390/en13195079 · Cited by 171 · cited 3×
“[49] also found success with SiO2 when combined with CeO2.”
BackgroundInfluentialHosseinzadeh, K., Erfani Moghaddam, M. A., Asadi, A., Mogharrebi, A. R., Jafari, B., Hasani, M. R., & Ganji, D. D. (2021) · Alexandria Engineering Journal · doi:10.1016/j.aej.2020.12.001 · Cited by 171
Algarni, S., Mellouli, S., Alqahtani, T., Almutairi, K., khan, A., & Anqi, A. (2020) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2020.115831 · Cited by 166 · cited 3×
“…with larger R. NP more effective for bottom injection Hosseini et al. (2013) [38] RT 50 (48 ◦C) Low Cu Melting Numerical (3D) Increased NP enhanced the system Algarni et al. (2020) [39] Paraffin wax (52 ◦C) Low Cu Melting and solidification Experimental NePCM enhancedefficiency by 32% Nitsas…”
BackgroundInfluentialVivekananthan, M., & Amirtham, V. A. (2019) · Thermochimica Acta · doi:10.1016/j.tca.2019.03.037 · Cited by 164
Han, D., Guene Lougou, B., Xu, Y., Shuai, Y., & Huang, X. (2020) · Applied Energy · doi:10.1016/j.apenergy.2020.114674 · Cited by 155 · cited 4×
“(2020) [73] KCl:MgCl2:NaCl (3997 ◦C ) Al2O3, CuO, and ZnO Melting Experimental Al2O3 showed the best enhancement”
BackgroundInfluentialChieruzzi, M., Miliozzi, A., Crescenzi, T., Torre, L., & Kenny, J. M. (2015) · Nanoscale Research Letters · doi:10.1186/s11671-015-0984-2 · Cited by 154 · cited 4×
“[71] focused on a high temperature PCM, experimentally testing KNO3 PCM with 1 wt % silica (SiO2), alumina (Al2O3), and SiO2-Al2O3 NPs.”
BackgroundMethodInfluentialTiari, S., Qiu, S., & Mahdavi, M. (2016) · Energy Conversion and Management · doi:10.1016/j.enconman.2016.04.025 · Cited by 150 · cited 8×
“(Copyright 2020 Elsevier) [80].”
BackgroundMethodSelf-citationRen, Q., Meng, F., & Guo, P. (2018) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2018.01.046 · Cited by 149 · cited 3×
“[86] numerically investigated the effects of changing different factors of the enhancements on an LHTES system.”
BackgroundInfluentialFeng, Y., Li, H., Li, L., Bu, L., & Wang, T. (2015) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2014.10.048 · Cited by 148 · cited 4×
“The copper NPs clearly enhanced the PCM melting process [30].”
BackgroundInfluentialSong, S., Qiu, F., Zhu, W., Guo, Y., Zhang, Y., Ju, Y., Feng, R., Liu, Y., Chen, Z., Zhou, J., et al. (2019) · Solar Energy Materials and Solar Cells · doi:10.1016/j.solmat.2019.01.023 · Cited by 146 · cited 7×
“PEG and Ag Marcos et al. [56] characterized polyvinylpyrrolidone-treated silver NPs in polyethylene glycol (PEG) PCM for low temperature applications.”
BackgroundInfluentialEnhancement of solidification rate of latent heat thermal energy storage using corrugated fins
Aly, K. A., El-Lathy, A. R., & Fouad, M. A. (2019) · Journal of Energy Storage · doi:10.1016/j.est.2019.100785 · Cited by 146 · cited 2×
“Increasing the number of corrugations, and therefore increasing the fin length, shortened the solidification time [17].”
BackgroundChieruzzi, M., Cerritelli, G. F., Miliozzi, A., Kenny, J. M., & Torre, L. (2017) · Solar Energy Materials and Solar Cells · doi:10.1016/j.solmat.2017.04.011 · Cited by 131 · cited 1×
“…(2013) [66] NaNO3-KNO3 (223–232 ◦C) Middle SiO2, Al2O3, TiO2, and SiO2-Al2O3 Melting and solidification Experimental 1.0 wt % SiO2-Al2O3 were the most effective Chieruzzi et al. (2017) [67] NaNO3-KNO3 (228.2 ◦C) Middle silica (SiO2), alumina (Al2O3), and SiO2-Al2O3 Melting and solidification…”
InfluentialTiari, S., & Qiu, S. (2015) · Energy Conversion and Management · doi:10.1016/j.enconman.2015.08.004 · Cited by 130 · cited 5×
“Some heating applications include building heating [3], waste heat recovery (for example, car exhaust, factories) [3,7] and solar food drying equipment [3].”
BackgroundInfluentialSelf-citationTiari, S., Hockins, A., & Mahdavi, M. (2021) · Case Studies in Thermal Engineering · doi:10.1016/j.csite.2021.100999 · Cited by 122 · cited 3×
“For discharging, as well as overall for both, twenty uniform fins were the best enhancement [18].”
BackgroundInfluentialSelf-citationMehta, D. S., Solanki, K., Rathod, M. K., & Banerjee, J. (2019) · Journal of Energy Storage · doi:10.1016/j.est.2019.03.007 · Cited by 121 · cited 2×
“The HTF temperature increase accelerated the melting process and increased the rate of energy stored [12].”
BackgroundThalib, M. M., Manokar, A. M., Essa, F. A., Vasimalai, N., Sathyamurthy, R., & Garcia Marquez, F. P. (2020) · Energies · doi:10.3390/en13153989 · Cited by 114 · cited 4×
“[44] conducted an experiment to test paraffin against grapheneenhanced paraffin in a tubular solar still (a device that desalinates water to provide potable fresh water).”
BackgroundInfluentialAqib, M., Hussain, A., Ali, H. M., Naseer, A., & Jamil, F. (2020) · Case Studies in Thermal Engineering · doi:10.1016/j.csite.2020.100753 · Cited by 114 · cited 3×
“The MWCNTs had higher peak temperatures than alumina NPs, making them the better option for enhancement [41].”
BackgroundInfluentialAssessment of latent heat thermal storage systems operating with multiple phase change materials
N., L. N. (2019) · Journal of Energy Storage · doi:10.1016/j.est.2019.04.008 · Cited by 113 · cited 2×
“Of course, the total energy storage may decrease; however, as with other enhancement techniques, the payoff can outweigh this drawback [22].”
BackgroundSenobar, H., Aramesh, M., & Shabani, B. (2020) · Journal of Energy Storage · doi:10.1016/j.est.2020.101911 · Cited by 111 · cited 3×
“[88] experimentally tested PCM alone, with NPs, with metal foam, and with both to see which setup was the most effective.”
BackgroundMethodInfluentialElbahjaoui, R., & El Qarnia, H. (2017) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2016.10.115 · Cited by 100 · cited 2×
“Elbahjaoui and El Qarnia (2017) [35] Paraffin wax (47 ◦C) Low Al2O3 Melting Numerical (2D) Increased NP, Reynolds number, Rayleigh number, and aspect ratio all decreased melting time”
BackgroundResultGasia, J., Maldonado, J. M., Galati, F., De Simone, M., & Cabeza, L. F. (2019) · Energy Conversion and Management · doi:10.1016/j.enconman.2019.01.085 · Cited by 99 · cited 4×
“[19] studied metal w ol shaped into fi it ril distributed.”
BackgroundInfluentialElbahjaoui, R., & El Qarnia, H. (2017) · Energy and Buildings · doi:10.1016/j.enbuild.2017.08.003 · Cited by 95 · cited 2×
“The NPs also improved the solidification rate [36].”
BackgroundAbdulateef, A. M., Jaszczur, M., Hassan, Q., Anish, R., Niyas, H., Sopian, K., & Abdulateef, J. (2021) · Journal of Energy Storage · doi:10.1016/j.est.2020.102227 · Cited by 95 · cited 3×
“…wax (PW-L: 44–48 ◦C PW-H: 64–66 ◦C) Low Al2O3 Melting and solidification Numerical (3D) Both paraffin thermal conductivities were improved by the NP Abdulateef et al. (2021) [32] Paraffin RT82 (78.15–82.15 ◦C) Low Al2O3 Melting Experimental and numerical (2D) The addition of NPs improved…”
BackgroundInfluentialBashar, M., & Siddiqui, K. (2018) · Journal of Energy Storage · doi:10.1016/j.est.2018.06.006 · Cited by 91 · cited 8×
“Then, copper oxide was tested in varying mass fractions, 1, 3, 6, 8, and 10%, and it was found that the 6% mass fraction performed best [46].”
BackgroundMethodInfluentialSingh, R. P., Sze, J. Y., Kaushik, S. C., Rakshit, D., & Romagnoli, A. (2021) · Journal of Energy Storage · doi:10.1016/j.est.2020.102092 · Cited by 90 · cited 4×
“The specific heat also increased with greater concentration of f-GNPs, and the latent heat was reduced [11].”
BackgroundInfluentialSaranprabhu, M. K., & Rajan, K. S. (2019) · Renewable Energy · doi:10.1016/j.renene.2019.04.027 · Cited by 89 · cited 5×
“25 wt % was deemed the most effective concentration [69].”
BackgroundMethodInfluentialMahdavi, M., Tiari, S., & Pawar, V. (2020) · Journal of Energy Storage · doi:10.1016/j.est.2019.101086 · Cited by 87 · cited 3×
“[82] conducted a numerical simulation of just heat pipes and NPs, using a two-dimensional axisymmetric model in ANSYS-FLUENT.”
BackgroundMethodSelf-citationPCM charging process accelerated with combination of optimized triangle fins and nanoparticles
Ren, Q., Xu, H., & Luo, Z. (2019) · International Journal of Thermal Sciences · doi:10.1016/j.ijthermalsci.2019.03.005 · Cited by 84 · cited 2×
“NePCM was further studied with the triangular fins, which showed that the long, narrow fins with unequal lengths (longer on bottom and shorter on top, to enhance convection on top and conduction on the bottom) greatly improved the NePCM melting rate [78].”
BackgroundKhatibi, M., Nemati-Farouji, R., Taheri, A., Kazemian, A., Ma, T., & Niazmand, H. (2021) · Journal of Energy Storage · doi:10.1016/j.est.2020.102055 · Cited by 84 · cited 3×
“The effect of the NPs was diminished with a decrease in HTF temperature and was also affected by the type of LHTES system [47].”
BackgroundMethodInfluentialYu, Q., Zhang, C., Lu, Y., Kong, Q., Wei, H., Yang, Y., Gao, Q., Wu, Y., & Sciacovelli, A. (2021) · Renewable Energy · doi:10.1016/j.renene.2021.03.061 · Cited by 84 · cited 2×
“2 times in the liquid state, and thermal cycling showed great thermal stability [92].”
BackgroundInfluence of orientation on thermal performance of shell and tube latent heat storage unit
Mehta, D. S., Solanki, K., Rathod, M. K., & Banerjee, J. (2019) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2019.113719 · Cited by 82
Experimental study of a latent heat thermal energy storage system assisted by a heat pipe network
Tiari, S., Mahdavi, M., & Qiu, S. (2017) · Energy Conversion and Management · doi:10.1016/j.enconman.2017.10.019 · Cited by 80 · cited 2×
“[14] found that an increase in HTF flow rate greatly decreased the charging time, but it had a less significant impact on the discharging time.”
BackgroundSelf-citationMa, C., Zhang, Y., Chen, X., Song, X., & Tang, K. (2020) · Materials · doi:10.3390/ma13040980 · Cited by 80 · cited 3×
“Heat storage speed was accelerated, and heat storage capacity was strengthened with the addition of the Cu particles [90].”
BackgroundInfluentialNakhchi, M. E., Hatami, M., & Rahmati, M. (2021) · Energy · doi:10.1016/j.energy.2020.119112 · Cited by 78 · cited 2×
“An increased stair ratio improved the energy storage capacity [76].”
BackgroundMethodSolidification of PCM within a tank with longitudinal-Y shape fins and CuO nanoparticle
Hajizadeh, M. R., Keshteli, A. N., & Bach, Q.-V. (2020) · Journal of Molecular Liquids · doi:10.1016/j.molliq.2020.114188 · Cited by 76 · cited 4×
“(2020) [75] RT35 (35 ◦C) Low CuO and branched fins Solidification Numerical (2D) NP improved all cases, case 2 worked best”
BackgroundInfluentialEffect of geometric parameter and nanoparticles on PCM melting in a vertical shell-tube system
Nie, C., Liu, J., & Deng, S. (2021) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2020.116290 · Cited by 75 · cited 2×
“(2021) [37] Paraffin RT35 (29–36 ◦C) Low Cu Melting Numerical (2D) Melting time shorter for top injection when R < 0.”
BackgroundInfluentialMayilvelnathan, V., & Valan Arasu, A. (2020) · International Journal of Thermal Sciences · doi:10.1016/j.ijthermalsci.2020.106446 · Cited by 68 · cited 4×
“They concluded that the system was an effective energy storage system [63].”
BackgroundInfluentialHuang, Z., Xie, N., Luo, Z., Gao, X., Fang, X., Fang, Y., & Zhang, Z. (2018) · Solar Energy Materials and Solar Cells · doi:10.1016/j.solmat.2017.11.006 · Cited by 66
Akhmetov, B., Navarro, M. E., Seitov, A., Kaltayev, A., Bakenov, Z., & Ding, Y. (2019) · Solar Energy · doi:10.1016/j.solener.2019.10.015 · Cited by 65 · cited 9×
“Authors PCM Melting Point (◦C) Nanoparticle Type Phase Change Process Study Case Result Elgafy and Lafdi (2005) [27] Paraffin wax (67 ◦C) Low Carbon nanofibers Solidification Experimental andanalytical (1D) The nanofibers enhanced the PCM performance Khodadadi and Hosseinizadeh (2007) [28] Water (0 ◦C) Low Cu Solidifi…”
BackgroundMethodInfluentialReyes, A., Negrete, D., Mahn, A., & Sepúlveda, F. (2014) · Energy Conversion and Management · doi:10.1016/j.enconman.2014.08.032 · Cited by 63 · cited 2×
“[20] also tested metal wool, but unlike Gaisa et al.”
BackgroundJavadi, H., Urchueguia, J. F., Mousavi Ajarostaghi, S. S., & Badenes, B. (2020) · Energies · doi:10.3390/en13195156 · Cited by 54 · cited 7×
“[45] studied Cu, CuO, Al2O3, TiO2, SiO2, multiwall carbon nanotubes, and graphene in paraffin using a three-dimensional numerical model.”
BackgroundMethodResultInfluentialMelting of Nanoprticle-Enhanced Phase Change Material inside Shell and Tube Heat Exchanger
Hosseini, S. M. J., Ranjbar, A. A., Sedighi, K., & Rahimi, M. (2013) · Journal of Engineering · doi:10.1155/2013/784681 · Cited by 53 · cited 3×
“They found that a higher volume fraction of NPs increased the liquid fraction and the penetration length of fluid, and it decreased the melting time [38].”
BackgroundInfluentialThermal energy storage behaviour of nanoparticle enhanced PCM during freezing and melting
P, M., P, G. K., V, K., M, M., K, M. M., & R, V. (2018) · Phase Transitions · doi:10.1080/01411594.2017.1372760 · Cited by 53 · cited 2×
“…(2018) [42] Paraffin wax (82 ◦C) Low Al2O3, TiO2, MgO, ZnO, MWCNTs and Graphene nanoplatelet Melting and solidification Experimental GNPs showed thebest improvement Murugan et al. (2018) [43] Paraffin (18–23 ◦C) Low MWCNT Melting and solidification Experimental Melting improved up to 0.3 wt…”
BackgroundInfluentialMaher, H., Rocky, K. A., Bassiouny, R., & Saha, B. B. (2021) · Thermal Science and Engineering Progress · doi:10.1016/j.tsep.2020.100797 · Cited by 53 · cited 4×
“[52] compared two different nanomaterials in paraffin wax to improve thermal conductivity.”
BackgroundInfluentialPrabakaran, R., Sidney, S., Lal, D. M., Selvam, C., & Harish, S. (2019) · Energies · doi:10.3390/en12183473 · Cited by 48 · cited 4×
“[59] experimentally investigated the solidification of the fatty acid PCM OM08 with graphene NPs.”
BackgroundInfluentialTiari, S., & Mahdavi, M. (2020) · Journal of Thermal Analysis and Calorimetry · doi:10.1007/s10973-020-09357-9 · Cited by 47 · cited 6×
“Heat pipe network schematic from Mahdavi et al. (Copyright 2016 Elsevier) [13].”
BackgroundSelf-citationBondareva, N. S., Gibanov, N. S., & Sheremet, M. A. (2020) · Nanomaterials · doi:10.3390/nano10020284 · Cited by 46 · cited 3×
“As a result of this, NPs only enhanced the system up to 2% concentration, which was determined to be the best concentration [80].”
BackgroundMethodInfluentialNePCM Based on Silver Dispersions in Poly(Ethylene Glycol) as a Stable Solution for Thermal Storage
Marcos, M. A., Cabaleiro, D., Hamze, S., Fedele, L., Bobbo, S., Estellé, P., & Lugo, L. (2019) · Nanomaterials · doi:10.3390/nano10010019 · Cited by 45
Liang, L., & Chen, X. (2018) · International Journal of Photoenergy · doi:10.1155/2018/6432047 · Cited by 42 · cited 5×
“Liang and Chen [54] experimentally studied the solidification of eutectic hydrate salts with carbon NPs.”
BackgroundInfluentialDoes nanoparticles dispersed in a phase change material improve melting characteristics?
Farsani, R. Y., Raisi, A., Nadooshan, A. A., & Vanapalli, S. (2017) · International Communications in Heat and Mass Transfer · doi:10.1016/j.icheatmasstransfer.2017.10.006 · Cited by 37 · cited 4×
“It was concluded that NPs had little to no influence on the Nusselt number and temperature throughout the melting process (shown in Figure 6), and therefore, they did not recommended using NPs for enhancement [34].”
BackgroundMethodInfluentialXiong, Y., Wang, Z., Wu, Y., Xu, P., Ding, Y., Chang, C., & Ma, C. (2019) · Applied Energy · doi:10.1016/j.apenergy.2019.01.026 · Cited by 37 · cited 3×
“[72], who created a eutectic mixture of sodium bromide, potassium bromide, lithium bromide, and calcium bromide enhanced with SiO2 NPs.”
BackgroundInfluentialu Mekrisuh, K., Giri, S., Udayraj, Singh, D., & Rakshit, D. (2021) · Journal of Energy Storage · doi:10.1016/j.est.2020.102126 · Cited by 36 · cited 4×
“(2021) [65] D-Mannitol (166–179 ◦C) Middle Graphene nano-plates Melting Numerical (2D) Optimizing geometry had better results than fins and nano-plates”
BackgroundMethodInfluentialAslfattahi, N., Rahman, S., Mohd Sabri, M. F., & Arifutzzaman, A. (2019) · International Journal of Technology · doi:10.14716/ijtech.v10i6.3568 · Cited by 33 · cited 4×
“TGA was also used to assess thermal stability and mass loss, which showed that the thermal stability was enhanced at high temperatures [68].”
BackgroundMethodInfluentialDutkowski, K., & Kruzel, M. (2019) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2019.118741 · Cited by 32
Barreneche, C., Martín, M., Calvo-de la Rosa, J., Majó, M., & Fernández, A. I. (2019) · Molecules · doi:10.3390/molecules24071232 · Cited by 31
Raj, C. R., Suresh, S., Singh, V. K., Bhavsar, R. R., Chandrasekar, M., & Archita, V. (2021) · Journal of Energy Storage · doi:10.1016/j.est.2020.102220 · Cited by 29 · cited 3×
“[10] used a eutectic mixture of gallium–indium metal alloy for their study.”
BackgroundMethodInfluentialImprovement of a novel heat pipe network designed for latent heat thermal energy storage systems
Mahdavi, M., Qiu, S., & Tiari, S. (2016) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2016.07.190 · Cited by 27 · cited 1×
“[13] developed a novel heat pipe network for LHTES application, as shown in Figure 3 [13].”
MethodSelf-citationNumerical Study of Latent Heat Thermal Energy Storage Enhancement by Nano-PCM in Aluminum Foam
Buonomo, B., Di Pasqua, A., Ercole, D., & Manca, O. (2018) · Inventions · doi:10.3390/inventions3040076 · Cited by 26 · cited 3×
“(2018) [89] RT 58 Paraffin (48–62 ◦C) Low Aluminum oxide NP, aluminum foam, heat pipes Melting Numerical (3D) Metal foam enhanced more than NPs; their combination was best.”
BackgroundMethodInfluentialThe experimental investigation of mPCM slurries density at phase change temperature
Dutkowski, K., Kruzel, M., Zajączkowski, B., & Białko, B. (2020) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2020.120083 · Cited by 26 · cited 2×
“[25] used the same encapsulated PCM to test changes in density during melting.”
BackgroundMethodKim, H. G., Kim, Y.-S., Kwac, L. K., Shin, H. J., Lee, S. O., Lee, U. S., & Shin, H. K. (2019) · Nanomaterials · doi:10.3390/nano9020158 · Cited by 22 · cited 3×
“Latent heat was reduced with the addition of foam but stayed relatively the same with the addition of the NPs; however, latent heat loss during thermal cycling was lower with the foam [91].”
BackgroundMethodInfluentialDutkowski, K., Kruzel, M., & Zajączkowski, B. (2020) · Energies · doi:10.3390/en14010179 · Cited by 21 · cited 2×
“The specific heat was lower at higher wt % when in liquid form but increased in solid form [26].”
BackgroundMethodUse of Nanoparticle Enhanced Phase Change Material for Cooling of Surface Acoustic Wave Sensor
Abdollahzadeh Jamalabadi, M. Y. (2021) · Fluids · doi:10.3390/fluids6010031 · Cited by 15
Thermal analysis of Fe2O3 - myristic acid nanocomposite for latent heat storage
Santhosh, S., Satish, M., Yadav, A., & Anish Madhavan, A. (2021) · Materials Today: Proceedings · doi:10.1016/j.matpr.2020.11.412 · Cited by 14 · cited 2×
“[60] used a fatty acid called myristic acid with Fe2O3 NPs at several different concentrations to test whether the particles enhanced the performance of the LHTES system.”
BackgroundMethodBadakhsh, A., An, K.-H., Park, C. W., & Kim, B.-J. (2018) · Journal of Nanomaterials · doi:10.1155/2018/8632350 · Cited by 13 · cited 4×
“[51], who experimented with the melting and solidification of paraffin with aluminum nitride coated SiC (SiC@AlN) particles.”
BackgroundInfluentialKoukou, M. K., Dogkas, G., Vrachopoulos, M. G., Konstantaras, J., Pagkalos, C., Lymperis, K., Stathopoulos, V., Evangelakis, G., Prouskas, C., Coelho, L., et al. (2019) · ChemEngineering · doi:10.3390/chemengineering3040088 · Cited by 13 · cited 2×
“(2019) [81] Paraffin (A44) (44 ◦C) Low Graphite nano-platelets and finned heat pipes Melting and solidification Experimental NPs reduced charging and discharging times”
BackgroundThermal Analysis of Pure and Nanoparticle-Enhanced PCM—Application in Concentric Tube Heat Exchanger
T. Nitsas, M., & P. Koronaki, I. (2020) · Energies · doi:10.3390/en13153841 · Cited by 13 · cited 3×
“Nitsas and Koronaki (2020) [40] RT50 (45–51 ◦C) Low Cu and Al2O3 Melting Numerical (2D) NPs enhanced melting”
BackgroundInfluentialA Comprehensive Review of Solar Thermal Energy Storage
Sârbu, I., & Sebarchievici, C. (2017) · Energy Storage · doi:10.18690/978-961-286-052-3.14 · Cited by 13
Zhou, Y., Jiang, Y., Liu, F., et al. (2016) · Cited by 12
Mahdavi, M., Tiari, S., & Pawar, V. (2018) · Volume 6B: Energy · doi:10.1115/imece2018-86609 · Cited by 10 · cited 3×
“(2018) [83] Rubitherm 55 (51–57 ◦C) Low Cu, CuO, Al2O3, Ag, and heat pipes Melting Numerical (2D) Enhancements improved melting, but type of NP was insignificant”
BackgroundInfluentialSelf-citationTiari, S., Mahdavi, M., Thakore, V., & Joseph, S. (2018) · Volume 6B: Energy · doi:10.1115/imece2018-86481 · Cited by 9 · cited 3×
“In comparison, the aluminum oxide particles had only a slightly higher melting rate than the Cu particles, which was insignificant [84].”
BackgroundInfluentialSelf-citationDastmalchi, M., & Boyaghchi, F. A. (2020) · Journal of Energy Storage · doi:10.1016/j.est.2020.101705 · Cited by 9 · cited 3×
“Dastmalchi and Boyaghch (2020) [48] RT25 (23–25 ◦C) Low SiO2 Melting and solidification Numerical (2D) Used properly, the system decreased the cost of the AC”
BackgroundMethodInfluentialChieruzzi, M., Miliozzi, A., Crescenzi, T., et al. (2016) · nano Online · doi:10.1515/nano.11671_2015.327 · Cited by 9
Numerical investigation on Nano-PCM in aluminum foam in latent thermal energy storages
Buonomo, B., Ercole, D., Manca, O., & Nardini, S. (2018) · Modelling Measurement and Control B · doi:10.18280/mmc_b.870313 · Cited by 6
Tiari, S., Rose, O. L., & Mahdavi, M. (2019) · Proceeding of 4th Thermal and Fluids Engineering Conference · doi:10.1615/tfec2019.tes.028083 · Cited by 4 · cited 2×
“There was not a significant difference between the two NP types [85].”
BackgroundSelf-citationPreparation and characterization of composite phase change materials containing nanoparticles
College of Aerospace and Civil Engineering, H. E. U., Yu, J., Yu, Z., College of Aerospace and Civil Engineering, H. E. U., Tang, C., College of Aerospace and Civil Engineering, H. E. U., Chen, X., College of Aerospace and Civil Engineering, H. E. U., Song, Q., College of Aerospace and Civil Engineering, H. E. U., et al. (2016) · Kemija u industriji · doi:10.15255/kui.2016.015 · Cited by 2 · cited 4×
“It is theorized in [87] that the conductive pathway formed by the sheet-shaped graphene NPs made them more effective.”
BackgroundMethodResultInfluentialExperimental and Numerical Study of a Latent Heat Thermal Energy Storage System Enhanced with Fins
Tiari, S., Hockins, A., & Moretti, S. (2020) · Proceedings of the ... International Conference on Fluid Flow, Heat and Mass Transfer · doi:10.11159/ffhmt20.134 · Cited by 1
Self-citation
Research works printed but not linked: 3
- 34. Zaidan, M.J.; Alhamdo, M.H. Improvement in heat transfer inside a phase change energy system. Int. J. Mech. Mechatron. Eng. 2018, 18, 33-46.
- 43. Temel, Ü.N.; Çiftçi, B.Y. Determination of thermal properties of a82 organic phase change material embedded with different type nanoparticles. Farkli Tipte Nanoparçaciklarla Katkilanan A82 Organik Faz De giştiren Malzemenin Termal. Özell İkler İn İn Belirlenmesi 2018, 38, 75-85.
- 65. Manickam, R.; Kalidoss, P.; Suresh, S.; Venkatachalapathy, S. Erythritol based nano-PCM for solar thermal energy storage. Int. Res. J. Eng. Technol. 2019, 6, 1631-1636.
Cited by
Nano-enhanced phase change materials: Fundamentals and applications
Said, Z., Pandey, A. K., Tiwari, A. K., Kalidasan, B., Jamil, F., Thakur, A. K., Tyagi, V. V., Sarı, A., & Ali, H. M. (2024) · Progress in Energy and Combustion Science · doi:10.1016/j.pecs.2024.101162 · Cited by 386
Togun, H., Sultan, H. S., Mohammed, H. I., Sadeq, A. M., Biswas, N., Hasan, H. A., Homod, R. Z., Abdulkadhim, A. H., Yaseen, Z. M., & Talebizadehsardari, P. (2024) · Journal of Energy Storage · doi:10.1016/j.est.2023.109840 · Cited by 245
Progress and key challenges in catalytic combustion of lean methane
Feng, X., Jiang, L., Li, D., Tian, S., Zhu, X., Wang, H., He, C., & Li, K. (2022) · Journal of Energy Chemistry · doi:10.1016/j.jechem.2022.08.001 · Cited by 211
Ghosh, D., Ghose, J., Datta, P., Kumari, P., & Paul, S. (2022) · Journal of Energy Storage · doi:10.1016/j.est.2022.105179 · Cited by 163
A brief review on different hybrid methods of enhancement within latent heat storage systems
Khademi, A., Shank, K. J., Mehrjardi, S. A. A., Tiari, S., Sorrentino, G., Said, Z., Chamkha, A. J., & Ushak, S. (2022) · Journal of Energy Storage · doi:10.1016/j.est.2022.105362 · Cited by 122
Self-citation
Metadata
- Authors
- Tofani, K., & Tiari, S.
- Affiliations
- Gannon University (US)
- Corresponding author
- Tiari, Saeed
- ORCID
- Tiari, Saeed
- Venue
- Energies
- Publisher
- MDPI AG
- Published
- 2021-06-25
- Volume
- 14
- Issue
- 13
- Pages
- 3821
- ISSN
- 1996-1073 (ISSN-L)
- OpenAlex
- W3175481636
- Cited by
- 114
- References
- 93
- Citations by year
- 2026: 34 · 2025: 18 · 2024: 21 · 2023: 22 · 2022: 16 · 2021: 3
- FWCI
- 6.62
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Energies (publishedVersion, cc-by)
- RePEc: Research Papers in Economics (submittedVersion)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Topics
- Physical Sciences › Engineering › Mechanical Engineering › Phase Change Materials Research
- Physical Sciences › Engineering › Mechanical Engineering › Adsorption and Cooling Systems
- Physical Sciences › Energy › Renewable Energy, Sustainability and the Environment › Solar Thermal and Photovoltaic Systems
- Keywords
- nano-enhanced phase change materials, latent heat storage, thermal conductivity enhancement, nanoparticles, metal foam, heat pipes, fins, porous media, solar energy storage, alkanes, Al2O3 nanoparticles, copper nanoparticles, carbon nanoparticles
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-09-28, under version 3 of the claim definition (prompt extract-v3).
A second model labelled each claim on 2026-09-28 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.