The DOI matches its Crossref record; 19 of the 19 references it cites were found in a registry or an index.
Experimental Exploration of Metal Cable as Reinforcement in 3D Printed Concrete
Open accessAbstract
The Material Deposition Method (MDM) is enjoying increasing attention as an additive method to create concrete mortar structures characterised by a high degree of form-freedom, a lack of geometrical repetition, and automated construction. Several small-scale structures have been realised around the world, or are under preparation. However, the nature of this construction method is unsuitable for conventional reinforcement methods to achieve ductile failure behaviour. Sometimes, this is solved by combining printing with conventional casting and reinforcing techniques. This study, however, explores an alternative strategy, namely to directly entrain a metal cable in the concrete filament during printing to serve as reinforcement. A device is introduced to apply the reinforcement. Several options for online reinforcement media are compared for printability. Considerations specific to the manufacturing process are discussed. Subsequently, pull-out tests on cast and printed specimens provide an initial characterisation of bond behaviour. Bending tests furthermore show the potential of this reinforcement method. The bond stress of cables in printed concrete was comparable to values reported for smooth rebar but lower than that of the same cables in cast concrete. The scatter in experimental results was high. When sufficient bond length is available, ductile failure behaviour for tension parallel to the filament direction can be achieved, even though cable slip occurs. Further improvements to the process should pave the way to achieve better post-crack resistance, as the concept in itself is feasible.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Bos, F., Wolfs, R., Ahmed, Z., & Salet, T. (2016) · Virtual and Physical Prototyping · doi:10.1080/17452759.2016.1209867 · Cited by 1,257
Self-citationDevelopments in construction-scale additive manufacturing processes
Lim, S., Buswell, R. A., Le, T. T., Austin, S. A., Gibb, A. G. F., & Thorpe, T. (2012) · Automation in Construction · doi:10.1016/j.autcon.2011.06.010 · Cited by 1,205
A critical review of the use of 3-D printing in the construction industry
Wu, P., Wang, J., & Wang, X. (2016) · Automation in Construction · doi:10.1016/j.autcon.2016.04.005 · Cited by 1,002
3D printing trends in building and construction industry: a review
Tay, Y. W. D., Panda, B., Paul, S. C., Noor Mohamed, N. A., Tan, M. J., & Leong, K. F. (2017) · Virtual and Physical Prototyping · doi:10.1080/17452759.2017.1326724 · Cited by 868
Building components for an outpost on the lunar soil by means of a novel 3D printing technology
Cesaretti, G., Dini, E., De Kestelier, X., Colla, V., & Pambaguian, L. (2014) · Acta Astronautica · doi:10.1016/j.actaastro.2013.07.034 · Cited by 806
3D printing in aerospace and its long-term sustainability
Joshi, S. C., & Sheikh, A. A. (2015) · Virtual and Physical Prototyping · doi:10.1080/17452759.2015.1111519 · Cited by 628
Properties of 3D-printed fiber-reinforced Portland cement paste
Hambach, M., & Volkmer, D. (2017) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2017.02.001 · Cited by 470
Mega-scale fabrication by Contour Crafting
Khoshnevis, B., Hwang, D., Yao, K. T., & Yeh, Z. (2006) · International Journal of Industrial and Systems Engineering · doi:10.1504/ijise.2006.009791 · Cited by 378 · cited 1×
“Khoshnevis [25] already recognised that an alternative to conventional reinforcement would be required, and could be incorporated in an automated process without limiting shaping possibilities.”
BackgroundHigh Tech Concrete: Where Technology and Engineering Meet
Salet, T. A. M., Bos, F. P., Wolfs, R. J. M., Ahmed, Z. Y., Hordijk, D. A., & Luković, M. (2017) · Springer eBooks · doi:10.1007/978-3-319-59471-2 · Cited by 260
Self-citationLocal and global bond characteristics of steel reinforcing bars
Haskett, M., OEHLERS, D. J., & Ali, M. S. M. (2007) · Engineering Structures · doi:10.1016/j.engstruct.2007.04.007 · Cited by 231
Ogura, H., Nerella, V. N., & Mechtcherine, V. (2018) · Materials · doi:10.3390/ma11081375 · Cited by 227
Mesh‐Mould: Robotically Fabricated Spatial Meshes as Reinforced Concrete Formwork
Hack, N., & Lauer, W. V. (2014) · Architectural Design · doi:10.1002/ad.1753 · Cited by 155
Lunar Contour Crafting - A Novel Technique for ISRU-Based Habitat Development
Khoshnevis, B., Bodiford, M., Burks, K., Ethridge, E., Tucker, D., Kim, W., Toutanji, H., & Fiske, M. (2005) · 43rd AIAA Aerospace Sciences Meeting and Exhibit · doi:10.2514/6.2005-538 · Cited by 138
3D Printing Concrete on temporary surfaces: The design and fabrication of a concrete shell structure
Costanzi, C. B., Ahmed, Z., Schipper, H. R., Bos, F. P., Knaack, U., & Wolfs, R. J. M. (2018) · Automation in Construction · doi:10.1016/j.autcon.2018.06.013 · Cited by 118
Self-citation3D Printing Concrete with Reinforcement
Bos, F. P., Ahmed, Z., Wolfs, R. J. M., & Salet, T. A. M. (2017) · Springer eBooks · doi:10.1007/978-3-319-59471-2_283 · Cited by 114
Self-citationKhoshnevis, B., Russell, R., Kwon, H., & Bukkapatnam, S. (2001) · IEEE Robotics & Automation Magazine · doi:10.1109/100.956812 · Cited by 71
Fabricating construction components using layer manufacturing technology
Lim, S., Le, T., Webster, J. T., Buswell, R. A., Austin, S. A., Gibb, A., & Thorpe, T. (2009) · Open Research Online (The Open University) · Cited by 45
Extraterrestrial Construction Using Contour Crafting
Khoshnevis, B., & Zhang, J. (2012) · doi:10.26153/tsw/15347 · Cited by 21
Special Issue: NextGen Materials for 3D Printing
Chua, C. K., Yeong, W. Y., & An, J. (2018) · Materials · doi:10.3390/ma11040555 · Cited by 7
Cited by
Paolini, A., Kollmannsberger, S., & Rank, E. (2019) · Additive Manufacturing · doi:10.1016/j.addma.2019.100894 · Cited by 673
Wangler, T., Roussel, N., Bos, F. P., Salet, T. A. M., & Flatt, R. J. (2019) · Cement and Concrete Research · doi:10.1016/j.cemconres.2019.105780 · Cited by 612
Self-citationNerella, V. N., Hempel, S., & Mechtcherine, V. (2019) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2019.01.235 · Cited by 605
Large-scale 3D printing concrete technology: Current status and future opportunities
Xiao, J., Ji, G., Zhang, Y., Ma, G., Mechtcherine, V., Pan, J., Wang, L., Ding, T., Duan, Z., & Du, S. (2021) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2021.104115 · Cited by 532
Design of a 3D printed concrete bridge by testing
Salet, T. A. M., Ahmed, Z. Y., Bos, F. P., & Laagland, H. L. M. (2018) · Virtual and Physical Prototyping · doi:10.1080/17452759.2018.1476064 · Cited by 504
Self-citation
Metadata
- Authors
- Bos, F., Ahmed, Z., Jutinov, E., & Salet, T.
- Venue
- Materials
- Publisher
- MDPI AG
- Published
- 2017-11-16
- Volume
- 10
- Issue
- 11
- Pages
- 1314
- ISSN
- 1996-1944 (ISSN-L)
- OpenAlex
- W2769989783
- Cited by
- 276
- References
- 19
- FWCI
- 17.08
- Type
- journal article
- Language
- en
- Open access
- gold
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.