Modelling the Proton-Conductive Membrane in Practical Polymer Electrolyte Membrane Fuel Cell (PEMFC) Simulation: A Review
Open accessThe DOI matches its Crossref record; 190 of the 192 references it cites were found in a registry or an index; 26 of the 228 sources its claims cite were checked for support.
Abstract
Theoretical models used to describe the proton-conductive membrane in polymer electrolyte membrane fuel cells (PEMFCs) are reviewed, including proton conductivity, water sorption, diffusion, electroosmotic drag, swelling, gas transport, and degradation parameterization.
Overview
CoChat Summary
TL;DR
This review synthesizes 30 years of membrane-transport modelling for low-temperature PEMFC simulation, focusing on macroscopically observable charge, water, heat, gas, and degradation phenomena. It argues that coupled proton–water transport models, especially the Springer and Weber–Newman frameworks, are the dominant practical choices, but that their parameterisation is still heavily reliant on older Nafion data.
Key findings
- The review finds that a simple Ohm’s-law membrane model is only adequate under uniform hydration; most spatially resolved PEMFC simulations need coupled proton–water transport because membrane conductivity depends strongly on water content and water flux is tied to electroosmotic drag.
- It identifies the Springer and Weber–Newman models as the most widely used coupled transport approaches, with the Weber–Newman framework separating vapour-equilibrated (VE) and liquid-equilibrated (LE) conditions and allowing different transport coefficients in each regime.
- The authors report that many recent simulations still rely on 1990s parameterisation: in a sampled set of 8 PEMFC simulations published since 2019, 6 used the Springer model and 2 used the Weber–Newman model; the Springer-based works drew exclusively on four experimental studies from 1998 or earlier on Nafion 117.
- The paper notes several quantitative values from the literature, including Nafion 1100 MEW ≈ 1.100 kg mol−1, dry density ρdry ≈ 2050 kg m−3, and an experimental interfacial proton resistance of at least 8 mΩ cm2 for a directly painted Nafion-based MEA.
Methods
- Narrative review of theoretical and empirical membrane-transport models for PEMFC simulation, with emphasis on practical continuum-scale device modelling rather than atomic-scale chemistry.
- Compiles and standardizes reported equations and parameterisations, especially for Nafion 1100, across transport topics including proton conductivity, sorption isotherms, water diffusivity, electroosmotic drag, interfacial resistances, hydraulic flow, thermal effects, gas crossover, contamination, and degradation.
- Uses literature comparison and qualitative appraisal; the paper also presents a sampled review of 8 recent 2D/3D PEMFC simulation papers to illustrate dependence on legacy parameter sets.
Limitations
- Stated in the paper: the review is explicitly not comprehensive for the broader proton-conductive membrane literature, not focused on atomic-scale structure, and does not cover cold-start freezing or high-temperature PEM devices; it also excludes a detailed discussion of ionomer morphology in catalyst layers.
- Stated in the paper: detailed discussion of model validation is beyond scope, and the authors note that many current models depend on outdated material parameterisation rather than state-of-the-art membranes.
- Evident from the text: the review is heavily centered on Nafion-family/PFSA membranes, so transferability to other chemistries is only discussed cautiously and not exhaustively.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures








![Figure 9 Permeation coefficients for H2 and O2 as a function of temperature, using data summarised by Weber and Newman [65].](https://figures.cochat.ai/paper-figures/05084ed56c6c40f3a001cea2ab83cd81/modelling-the-proton-conductive-membrane-in-practical-polymer-electrolyte-figure-9.jpg)
![Figure 10 Henry’s law coefficients for H2 and O2 as a function of temperature, using data summarised by Wong and Kjeang [137].](https://figures.cochat.ai/paper-figures/1e3cab47d93c40409fa5cca1bd9434fe/modelling-the-proton-conductive-membrane-in-practical-polymer-electrolyte-figure-10.jpg)
Verification
Claims the paper makes
21 Valid · 10 Not valid · 134 Not checked · 70 Own results and interpretations
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“A number of empirical sorption isotherms have been established experimentally based on measurements on Nafion 1100 [39,51,52,53,54].”
§ Modelling the Proton-Conductive Membrane in Practical Polymer Electrolyte Membrane Fuel Cell (PEMFC) Simulation: A Review > 4. Sorption of Water > 4.2. Empirical Sorption Models for Nafion 1100
What the sources say
- Partly supportedcites [39] Springer, 1991, Polymer Electrolyte Fuel Cell Model, J. Electrochem. Soc. sourceExperimental — accuracy not yet measured
The Mathematical Model section (page unavailable) reports an experimentally measured isopiestic curve and an empirical fit relating water content to water activity for Nafion 117. It supports the existence of an experimentally based sorption relationship, but does not establish that this paper presents a number of isotherms or identify the measured membrane as “Nafion 1100.” (LLM, conf=0.83)
- Could not verifycites [51] Springer, 1993, Modeling and Experimental Diagnostics in Polymer Electrolyte Fuel Cells, J. Electrochem. Soc. sourceExperimental — accuracy not yet measured
Our copy of Springer et al. (1993) is a cathode-focused modeling and diagnostics paper: the closest membrane material is the Abstract/introduction statement that earlier work 'focused on the losses in the ionomeric membrane, which we calculated for PEFC membranes of well-characterized transport properties' and the conductivity measurements on silica/recast-Nafion composites ('Calculated effects of permeability and conductivity limitations'). No passage reports or discusses empirical water sorption isotherms, and no passage mentions Nafion 1100 (searched: 'sorption isotherm Nafion 1100 water uptake', 'membrane water sorption relative humidity lambda', 'equilibrium water content versus activity isotherm'). Nothing in our copy contradicts the claim either, so the cited five references cannot be checked against this source. (LLM, conf=0.70)
- Partly supportedcites [52] Zawodzinski, 1993, Water Uptake by and Transport Through Nafion® 117 Membranes, J. Electrochem. Soc. sourceExperimental — accuracy not yet measured
The Experimental section describes measuring water sorption, and Results and Discussion presents an isopiestic sorption curve for Nafion 117 at 30°C. This supports the paper as one source of experimental sorption data, but our copy does not identify the membrane as “Nafion 1100” or establish multiple isotherms in this paper. (LLM, conf=0.82)
- Not checked — no full text of the sourcecites [53] Zawodzinski, 1993, Characterization of polymer electrolytes for fuel cell applications, Solid State Ion. source
- Not checked — no full text of the sourcecites [54] Broka, 1997, Modelling the PEM fuel cell cathode, J. Appl. Electrochem. source
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“The most commonly used sorption isotherm is an empirical polynomial relation due to Springer et al. [39]:”
§ Modelling the Proton-Conductive Membrane in Practical Polymer Electrolyte Membrane Fuel Cell (PEMFC) Simulation: A Review > 4. Sorption of Water > 4.2. Empirical Sorption Models for Nafion 1100
What the sources say
- Partly supportedcites [39] Springer, 1991, Polymer Electrolyte Fuel Cell Model, J. Electrochem. Soc. sourceExperimental — accuracy not yet measured
The Mathematical Model section (page not available) gives an empirical polynomial relating membrane water content to water activity, supporting the attribution of that relation to Springer et al. Our copy does not establish that it is the most commonly used sorption isotherm. (LLM, conf=0.88)
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The sources with a verdict support this claim; the rest weren’t checked yet, have no full text we could read, or their verdicts aren’t rated yet.
In the paper
“From a thermodynamic standpoint, the inclusion of pressure as a local variable, in addition to electrolyte potential and water content, is almost certainly an overdetermination of the system except for the liquid-equilibrated case; it has not found general support [65,78].”
§ Modelling the Proton-Conductive Membrane in Practical Polymer Electrolyte Membrane Fuel Cell (PEMFC) Simulation: A Review > 5. Coupled Proton-Water Transport
What the sources say
- Supportedcites [65] Weber, 2004, Transport in polymer-electrolyte membranes—II. Mathematical model, J. Electrochem. Soc. source
In the Mathematical Model section (page unavailable), the paper says that treating pressure as a separate driving force in a vapor-equilibrated membrane adds a variable and requires another equation or assumption; it calls common treatments nonrigorous and potentially arbitrary. It distinguishes the liquid-equilibrated case, where the chemical-potential driving force can be expressed in terms of pressure alone. (LLM, conf=0.86)
- Not checked — no full text of the sourcecites [78] Paddison, S.J., and Promislow, K.S. (2009). Coupled Proton and Water Transport in Polymer Electrolyte Membranes. Device and Materials Modeling in PEM Fuel Cells, Springer. source
hedged- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“From a thermodynamic standpoint, the inclusion of pressure as a local variable, in addition to electrolyte potential and water content, is almost certainly an overdetermination of the system except for the liquid-equilibrated case; it has not found general support [65,78].”
§ Modelling the Proton-Conductive Membrane in Practical Polymer Electrolyte Membrane Fuel Cell (PEMFC) Simulation: A Review > 5. Coupled Proton-Water Transport
What the sources say
- Partly supportedcites [65] Weber, 2004, Transport in polymer-electrolyte membranes—II. Mathematical model, J. Electrochem. Soc. sourceExperimental — accuracy not yet measured
The Mathematical Model section says that separating chemical potential into activity and pressure in a vapor-equilibrated membrane introduces another variable and requires an additional equation or assumption; it also says the common treatments are not rigorous. It distinguishes the liquid-equilibrated case, where pressure can be the driving force. It does not say that including pressure overdetermines a system specified by electrolyte potential and water content, or establish the broader claim that the approach has not found general support. Page numbers are unavailable in our copy. (LLM, conf=0.82)
- Not checked — no full text of the sourcecites [78] Paddison, S.J., and Promislow, K.S. (2009). Coupled Proton and Water Transport in Polymer Electrolyte Membranes. Device and Materials Modeling in PEM Fuel Cells, Springer. source
hedged- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
Every source the paper cites for this claim was checked and supports it.
In the paper
“Weber and Newman have advocated the interpretation of the hydrated membrane as a system with three chemical components: water, protons, and fixed membrane structure [65].”
§ Modelling the Proton-Conductive Membrane in Practical Polymer Electrolyte Membrane Fuel Cell (PEMFC) Simulation: A Review > 5. Coupled Proton-Water Transport
What the sources say
- Supportedcites [65] Weber, 2004, Transport in polymer-electrolyte membranes—II. Mathematical model, J. Electrochem. Soc. source
The Mathematical Model section describes a concentrated-solution system composed of water, proton, and membrane. It also identifies the membrane as stationary, matching the claim’s fixed membrane structure. Page numbers are not provided in our copy. (LLM, conf=0.94)
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
97 more claims · 11 with their cited sources checked
Create a free account to see all 235 claims and to verify the 62 references still open.
- It may state two separate claims as one. 78
- Probably not a substantial claim. 84
Citations
Cites
Polymer Electrolyte Fuel Cell Model
Springer, T. E., Zawodzinski, T. A., & Gottesfeld, S. (1991) · Journal of The Electrochemical Society · doi:10.1149/1.2085971 · Cited by 3,528
New Insights into Perfluorinated Sulfonic-Acid Ionomers
Kusoglu, A., & Weber, A. Z. (2017) · Chemical Reviews · doi:10.1021/acs.chemrev.6b00159 · Cited by 2,432
Kreuer, K.-D., Paddison, S. J., Spohr, E., & Schuster, M. (2004) · Chemical Reviews · doi:10.1021/cr020715f · Cited by 2,187
Review of the proton exchange membranes for fuel cell applications
Peighambardoust, S. J., Rowshanzamir, S., & Amjadi, M. (2010) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2010.05.017 · Cited by 2,186
Anion-exchange membranes in electrochemical energy systems
Varcoe, J. R., Atanassov, P., Dekel, D. R., Herring, A. M., Hickner, M. A., Kohl, P. A., Kucernak, A. R., Mustain, W. E., Nijmeijer, K., Scott, K., et al. (2014) · Energy Environ. Sci. · doi:10.1039/c4ee01303d · Cited by 2,051
Water Uptake by and Transport Through Nafion® 117 Membranes
Zawodzinski, T. A., Derouin, C., Radzinski, S., Sherman, R. J., Smith, V. T., Springer, T. E., & Gottesfeld, S. (1993) · Journal of The Electrochemical Society · doi:10.1149/1.2056194 · Cited by 1,530
A Mathematical Model of the Solid‐Polymer‐Electrolyte Fuel Cell
Bernardi, D. M., & Verbrugge, M. W. (1992) · Journal of The Electrochemical Society · doi:10.1149/1.2221251 · Cited by 1,368
Porous‐electrode theory with battery applications
Newman, J., & Tiedemann, W. (1975) · AIChE Journal · doi:10.1002/aic.690210103 · Cited by 1,255
Solid polymer electrolyte membranes for fuel cell applications—a review
Smitha, B., Sridhar, S., & Khan, A. A. (2005) · Journal of Membrane Science · doi:10.1016/j.memsci.2005.01.035 · Cited by 1,216
A Water and Heat Management Model for Proton‐Exchange‐Membrane Fuel Cells
Nguyen, T. V., & White, R. E. (1993) · Journal of The Electrochemical Society · doi:10.1149/1.2220792 · Cited by 1,134
Research works printed but not linked: 3
- The Chemours Company FC, LLC. (2017). Product Bulletin P-11: Nafion(TM) NR211 and NR212 Ion Exchange Materials: Solution Cast Membranes, The Chemours Company FC, LLC.
- The Chemours Company FC, LLC. (2016). Product Bulletin P-12: Nafion(TM) N115, N117 and N1110 Ion Exchange Materials: Extrusion Cast Membranes, The Chemours Company FC, LLC.
- Paddison, S.J., and Promislow, K.S. (2009). A Combination Model for Macroscopic Transport in Polymer-Electrolyte Membranes. Device and Materials Modeling in PEM Fuel Cells, Springer. · DOI · Paper page
Cited by
A review on lifetime prediction of proton exchange membrane fuel cells system
Hua, Z., Zheng, Z., Pahon, E., Péra, M.-C., & Gao, F. (2022) · Journal of Power Sources · doi:10.1016/j.jpowsour.2022.231256 · Cited by 289
Application of Machine Learning in Optimizing Proton Exchange Membrane Fuel Cells: A Review
Ding, R., Zhang, S., Chen, Y., Rui, Z., Hua, K., Wu, Y., Li, X., Duan, X., Wang, X., Li, J., et al. (2022) · Energy and AI · doi:10.1016/j.egyai.2022.100170 · Cited by 171
Yang, L., Nik-Ghazali, N.-N., Ali, M. A. H., Chong, W. T., Yang, Z., & Liu, H. (2023) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2023.113737 · Cited by 168
A survey of Digital Twin techniques in smart manufacturing and management of energy applications
Wang, Y., Kang, X., & Chen, Z. (2022) · Green Energy and Intelligent Transportation · doi:10.1016/j.geits.2022.100014 · Cited by 147
Pan, Y., Wang, H., & Brandon, N. P. (2021) · Journal of Power Sources · doi:10.1016/j.jpowsour.2021.230560 · Cited by 129
Metadata
- Authors
- Dickinson, E. J. F., & Smith, G.
- Affiliations
- National Physical Laboratory (GB)
- Corresponding author
- Dickinson, Edmund J. F.
- Venue
- Membranes
- Publisher
- MDPI AG
- Published
- 2020-10-28
- Volume
- 10
- Issue
- 11
- Pages
- 310
- ISSN
- 2077-0375 (ISSN-L)
- PMC
- PMC7692588
- OpenAlex
- W3097817857
- Cited by
- 109
- References
- 192
- Citations by year
- 2026: 17 · 2025: 17 · 2024: 26 · 2023: 20 · 2022: 17 · 2021: 12
- FWCI
- 0.56
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Membranes (publishedVersion, cc-by)
- PubMed Central (publishedVersion, cc-by)
- PubMed (publishedVersion)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Fraunhofer-Publica (Fraunhofer-Gesellschaft) (submittedVersion)
- Funders
- Department for Business, Energy and Industrial Strategy, UK Government (National Measurement System)
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Fuel Cells and Related Materials
- Physical Sciences › Materials Science › Materials Chemistry › Advancements in Solid Oxide Fuel Cells
- Physical Sciences › Chemical Engineering › Filtration and Separation › Membrane-based Ion Separation Techniques
- Keywords
- proton-conducting membranes, proton exchange membrane fuel cells, proton transport, moisture sorption isotherms, water diffusion coefficient, electro-osmotic drag, membrane swelling, non-isothermal transport, gas transport, membrane degradation
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol and qwen3.8-omni-flash).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Modelling the Proton-Conductive Membrane in Practical Polymer Electrolyte Membrane Fuel Cell (PEMFC) Simulation: A Review. https://app.cochat.ai/papers/10.3390/membranes10110310
- The paper
- Dickinson, E. J. F., & Smith, G. (2020). Modelling the Proton-Conductive Membrane in Practical Polymer Electrolyte Membrane Fuel Cell (PEMFC) Simulation: A Review. Membranes. https://doi.org/10.3390/membranes10110310
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.