The DOI matches its Crossref record; 279 of the 288 references it cites were found in a registry or an index; 28 of the 288 sources its claims cite were checked for support.
Nanoparticles Engineering by Pulsed Laser Ablation in Liquids: Concepts and Applications
Open accessAbstract
Laser synthesis emerges as a suitable technique to produce ligand-free nanoparticles, alloys and functionalized nanomaterials for catalysis, imaging, biomedicine, energy and environmental applications. In the last decade, laser ablation and nanoparticle generation in liquids has proven to be a unique and efficient technique to generate, excite, fragment and conjugate a large variety of nanostructures in a scalable and clean way. In this work, we give an overview on the fundamentals of pulsed laser synthesis of nanocolloids and new information about its scalability towards selected applications. Biomedicine, catalysis and sensing are the application areas mainly discussed in this review, highlighting advantages of laser-synthesized nanoparticles for these types of applications and, once partially resolved, the limitations to the technique for large-scale applications.
Overview
CoChat Summary
TL;DR
This review surveys pulsed laser ablation in liquids (LAL) as a chemically clean route to ligand-free nanoparticles, alloys, and functional nanomaterials for biomedicine, catalysis, sensing, energy, and environmental applications. It concludes that LAL offers strong control over purity, crystal structure, and size distribution, but large-scale application still requires better colloidal stability, surface control, and defined gram-scale protocols.
Key findings
- LAL is presented as a scalable and clean synthesis route for nanocolloids, with applications in plasmonic sensing, nanomedicine, catalysis, and pollutant degradation; however, the review states that LAL colloids are “not yet applicable on a large scale.”
- Process parameters strongly affect productivity: IR laser light generally gives higher metal productivity than UV or Vis, but short wavelengths can become less productive at high colloid concentrations due to NP shielding; an optimum pulse duration is probably around single picoseconds. Electric-field-assisted LAL increased ablation rate by a factor of three, about 300 mg/30 min versus 100 mg/30 min without the field.
- Plasmonic tuning is demonstrated: Au/Ag alloy colloids can tune plasmon resonance continuously from about 400 nm (Ag) to 520 nm (Au); Ag spherical NPs showed higher plasmon sensitivity (125 nm/RIU) than Au NPs (45 nm/RIU), with roughly threefold increase after conversion to nanoplates and S = 460 nm/RIU after 730 nm irradiation.
- In photocatalysis, blue titania removed 76% of benzene after 80 min, while AuTiO2 left less than 1% residual benzene; after 5 min, BTX decreased by 53% with Au-decorated TiO2, 26% with blue TiO2, and 14% with commercial TiO2. Apparent rate constants increased from 1.4 × 10−2 min−1 (bare TiO2) to 3.8 × 10−2 min−1 (blue TiO2) and 8.3 × 10−2 min−1 (Au-loaded TiO2).
Methods
- Design: narrative review/overview of LAL fundamentals, process parameters, upscaling, and selected applications, not a primary systematic experimental study.
- Data/sample: synthesizes literature and the authors’ own contributions on ns/ps/fs LAL of metals and semiconductors in water and organic solvents, field-assisted LAL, plasmonic Au/Ag/Rh nanocolloids, SERS-based targeting, and TiO2/ZnO photocatalysis including BTX-contaminated industrial waters.
- Main analysis: qualitative and quantitative synthesis of cited experimental results, including optical emission spectroscopy, XRD/XPS, Raman/SERS, UV–Vis, plasmon sensitivity measurements, and photocatalytic degradation kinetics.
Limitations
- The paper states that LAL colloids are not yet large-scale applicable; reaching gram-scale production requires a properly defined LAL procedure and protocol, higher colloidal stability, and prevention of aggregation and larger-particle formation.
- It states that “ligand/surfactant-free” LAL NPs are not totally naked and still bear surface chemistry, with some surface atoms oxidized or complexed; an appropriate protocol for performance-oriented colloidal synthesis and isochronous surface modification is still not defined.
- The text also notes practical limits for nanoadsorption/nanophotocatalysis, the need for higher UV-SERS signal-to-noise, moderate Rh SERS enhancement with photo-degradation under 457 nm irradiation, and that the literature lacks full-range parameter data for productivity evaluation; as a review, it also relies on cited studies and selected examples rather than exhaustive primary data.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures


![Figure 3 (a) Image of laser-induced plasma on Al target immersed in water, acquired with ICCD camera. (b) Plasma temperature 2D map calculated as reported in [43] (Al target in MilliQ water, Elaser = 270 mJ, laser crater size = 1 ± 0.2 mm, λlaser = 532 nm, laser pulse duration = 6 ns, laser frequency = 10 Hz, delay time = 40 ns, gate width = 20 ns). (c) 3D representation of plasma temperature in (b).](https://figures.cochat.ai/paper-figures/96cfaa719e534646880c2f1310e9d25d/nanoparticles-engineering-by-pulsed-laser-ablation-in-liquids-concepts-and-figure-3.jpg)
![Figure 4 Time resolved shadowgraphy images of the laser induced bubble on Ag target immersed in water (a) and the corresponding bubble radius compared with the number of ejected Ag NPs during the bubble evolution (as calculated in [44]) (b). Experimental conditions: laser energy = 108 mJ, laser frequency = 2 Hz, laser crater size = 1 ± 0.2 mm, ICCD gate width = 20 µs and 5 accumulations for each image.](https://figures.cochat.ai/paper-figures/2fa383cc466a48779a6320553abcd0fe/nanoparticles-engineering-by-pulsed-laser-ablation-in-liquids-concepts-and-figure-4.jpg)
![Figure 5 Dependence graph of process parameters, arranged in component clusters, relevant to LAL up-scaling. If not marked differently by an arrow, the flow goes from the left to the right in horizontal direction and from the outside to the inside in vertical direction. Colors were used only for an improved overview. Reprinted with permission from [66].](https://figures.cochat.ai/paper-figures/cde1d6599a99445b96e13723f9ab45f6/nanoparticles-engineering-by-pulsed-laser-ablation-in-liquids-concepts-and-figure-5.jpg)
![Figure 6 Schematic of the laser ablation of metals in liquids at different wavelengths in absence (a) and presence (b) of colloidal particles. Equal energy densities were assumed for all laser spots. The diagram in (c) (linear scales for both axes) demonstrates the effect of an increasing colloidal concentration on the NP productivity in LAL at different wavelengths. The trends shown in the diagram represent the interpretation of the combined results of the discussed literature in Section 2.2.1. Reprinted with permission from [66].](https://figures.cochat.ai/paper-figures/78878d1c8aa84446bff81498c7ff288c/nanoparticles-engineering-by-pulsed-laser-ablation-in-liquids-concepts-and-figure-6.jpg)
![Figure 7 Illustration of the laser ablation of metals in liquids at different fluences varied by the pulse energy (a) and the working distance (b). The diagram in (c) demonstrates how the fluence variation caused by different initial spot sizes affects the NP productivity in LAL in the high-fluence regime. A Gaussian beam profile was assumed. In (c), both axes scale linearly. The trends shown in the diagram represent the interpretation of the combined results of the discussed literature in Section 2.2.1. The arrow and the less dense (dashed) line style in (c) indicate the trend in productivity induced by a smaller initial spot size. Reprinted with permission from [66].](https://figures.cochat.ai/paper-figures/69dcd42ab0de4a2581b8c3957bcdb61a/nanoparticles-engineering-by-pulsed-laser-ablation-in-liquids-concepts-and-figure-7.jpg)
![Figure 8 Illustration of the laser ablation of metals in liquids at different pulse durations neglecting non-linear effects. Thermal losses (a) and self-shielding by plasma (b) of pulses of different duration regimes. The diagram in (c) demonstrates how the coupling constant of electrons and phonons affects the NP productivity in LAL, depending on the laser pulse duration. A change of the coupling constant was assumed to have no influence on other material properties. In (c), the y-axis scales linearly. The trends shown in the diagram represent the interpretation of the combined results of the discussed literature in Section 2.2.1. In (c), the arrow and the less dense (dashed) line style indicate the effect of a longer coupling time of electrons and phonons of the target material on productivity. Reprinted with permission from [66].](https://figures.cochat.ai/paper-figures/082c9541edfe4142a53c0bd091799e62/nanoparticles-engineering-by-pulsed-laser-ablation-in-liquids-concepts-and-figure-8.jpg)
![Figure 9 Illustration of the optical breakdown of the liquid during the laser ablation of metals in liquids at different intensities neglecting non-linear effects. Dependence of the occurrence of the optical breakdown on the laser pulse duration (a) and on the colloid concentration (b). Reprinted with permission from [66].](https://figures.cochat.ai/paper-figures/67a4968f676d47e8a3d8c4f31c27e126/nanoparticles-engineering-by-pulsed-laser-ablation-in-liquids-concepts-and-figure-9.jpg)
![Figure 10 Illustration of a too short (a) and an appropriate (b) interpulse distance in the laser ablation of metals in liquids. The diagram in (c) demonstrates relative effects of different laser pulse durations on the dependence of the productivity on the inter-pulse distance. In (c), both axes scale linearly. The trends shown in the diagram represent the interpretation of the combined results of the discussed literature in Section 2.2.1. In (c), the arrow and the less dense line style indicate the effect of a longer laser pulse duration on productivity. Reprinted with permission from [66].](https://figures.cochat.ai/paper-figures/80abd62fefc240409da8004f1150f734/nanoparticles-engineering-by-pulsed-laser-ablation-in-liquids-concepts-and-figure-10.jpg)
![Figure 11 Illustration of the effect of the liquid flow rate (a) and of the liquid layer height (b) on the productivity in the laser ablation of metals in liquids. The diagram in (c) demonstrates relative effects of different liquid layer heights on the dependence of the productivity on the volume flow rate. In (c), both axes scale linearly. The trends shown in the diagram represent the interpretation of the combined results of the discussed literature in Section 2.2.1. In (c), the dashed line shows the effect of lower liquid layer height on the productivity, and the dashed line shows the effect of a too low liquid layer height compared to the solid line, respectively. Reprinted with permission from [66].](https://figures.cochat.ai/paper-figures/163ce9e6e4d240d8b028b2943d6757ad/nanoparticles-engineering-by-pulsed-laser-ablation-in-liquids-concepts-and-figure-11.jpg)
![Figure 12 Illustration of the effect of the target thickness in the laser ablation of metals in liquids (a) and the influence of the laser pulse duration on the heat confinement in thin targets (b). The diagram in (c) demonstrates relative effects of different laser pulse duration on the dependence of the productivity on the ablation target thickness. In (c), both axes scale linearly. The trends shown in the diagram represent the interpretation of the combined results of the discussed literature in Section 2.2.1. In (c), the arrow and the less dense line style indicate the effect of longer pulse duration on productivity. In (c), the vertical solid line in the center of the diagram marks the penetration depths of the laser pulse into the target material. Reprinted with permission from [66].](https://figures.cochat.ai/paper-figures/9affca35ffcc431a827e3dce2b836b79/nanoparticles-engineering-by-pulsed-laser-ablation-in-liquids-concepts-and-figure-12.jpg)


![Figure 15 Optical absorption spectra of spherical vs triangular silver NPs (a); SEM image of spherical NPs (b) and of triangular nanoparticles (c) TEM image and in the inset AFM profiles of triangular NPs (d). Reprinted from Ref. [156], Copyright (2019), with permission from Elsevier.](https://figures.cochat.ai/paper-figures/e83c97438fba4994acc9a4ac03278118/nanoparticles-engineering-by-pulsed-laser-ablation-in-liquids-concepts-and-figure-15.jpg)
![Figure 16 Plasmon sensitivity measurements from gold and silver spherical nanoparticles, obtained by laser ablation in water, and silver triangular nanoplates obtained by white light irradiation of the same spherical NPs (a); plasmon sensitivity measurements from triangular NPs obtained from monochromatic light irradiation of spherical NPs (also shown) obtained by laser ablation (b). Figure 16a reprinted from Ref. [156], Copyright (2019), with permission from Elsevier. Figure 16b reprinted from Ref. [170], with the permission of The Royal Society of Chemistry.](https://figures.cochat.ai/paper-figures/8536c795c71b46dfb0ce0c8ab3fba3ac/nanoparticles-engineering-by-pulsed-laser-ablation-in-liquids-concepts-and-figure-16.jpg)





Verification
Claims the paper makes
22 Valid · 9 Not valid · 150 Not checked · 135 Own results and interpretations
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“All studies agree independently from the ablated matter, the chosen liquid and the used laser pulse duration on a higher productivity by using IR laser light compared to UV or Vis.”
§ Nanoparticles Engineering by Pulsed Laser Ablation in Liquids: Concepts and Applications > 2. LAL Synthesis Methods: Principle, Process Parameters and Liquids Effects on Nanoparticle Formation > 2.2. Upscaling of Laser Synthesis of Colloids
What the sources say
- Partly supportedcites [54] Schwenke, 2011, Influence of processing time on nanoparticle generation during picosecond-pulsed fundamental and second harmonic laser ablation of metals in tetrahydrofuran, Appl. Phys. A sourceExperimental — accuracy not yet measured
The Results and discussion and Conclusions report higher nanoparticle productivity at the fundamental IR wavelength than at the visible second harmonic wavelength for Ag, Zn, and Mg ablated with picosecond pulses in polyurethane-doped tetrahydrofuran. The Introduction also reports similar findings from several studies using nanosecond pulses. These passages do not establish agreement among all studies regardless of material, liquid, or pulse duration, and the paper does not test a UV comparison. Page numbers were not provided for these passages. (LLM, conf=0.88)
- Not checked yetcites [67] Tsuji, 2000, Preparation of Metal Colloids by a Laser Ablation Technique in Solution: Influence of Laser Wavelength on the Efficiencies of Colloid Formation, Jpn. J. Appl. Phys. source
Checked before — its earlier verdict is held back until a new check runs.
- Not matchedcites [68] Pfleger, 2007, Laser ablation of silver in aqueous ambient: Effect of laser pulse wavelength and energy on efficiency of the process, J. Physics: Conf. Ser.
Couldn’t be matched to a paper in Crossref, so it can’t be checked.
- Not checked — no full text of the sourcecites [69] Intartaglia, 2014, Study on the productivity of silicon nanoparticles by picosecond laser ablation in water: Towards gram per hour yield, Opt. Express source
- Not checked — no full text of the sourcecites [70] Kim, 2014, The influence of laser wavelength and fluence on palladium nanoparticles produced by pulsed laser ablation in deionized water, Solid State Sci. source
boostedstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“The basic mechanisms inducing the laser ablation in liquid, as well as their dependence on laser pulse properties, do not differ notably, with respect of laser ablation in gaseous environment [54].”
§ Nanoparticles Engineering by Pulsed Laser Ablation in Liquids: Concepts and Applications > 2. LAL Synthesis Methods: Principle, Process Parameters and Liquids Effects on Nanoparticle Formation > 2.1. Mechanism in ns-Pulsed Laser Ablation in Liquid for the Production of Metallic Nanoparticles
What the sources say
- Partly supportedcites [54] Schwenke, 2011, Influence of processing time on nanoparticle generation during picosecond-pulsed fundamental and second harmonic laser ablation of metals in tetrahydrofuran, Appl. Phys. A sourceExperimental — accuracy not yet measured
The Introduction (page unavailable) says pulse duration changes the ablation mechanism in liquid, and the Results and discussion report effects of wavelength and fluence. The paper does not compare those mechanisms or their dependence on pulse properties with ablation in a gaseous environment, so the claimed similarity is unsupported. (LLM, conf=0.78)
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Rests on an assumption not shown here.
- Partly supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“The absence of the typical atomic spectral lines of the LIP expanding in a gaseous environment is due to the high density reached by the ablated matter under liquid confinement as discussed in [40,41,42].”
§ Nanoparticles Engineering by Pulsed Laser Ablation in Liquids: Concepts and Applications > 2. LAL Synthesis Methods: Principle, Process Parameters and Liquids Effects on Nanoparticle Formation > 2.1. Mechanism in ns-Pulsed Laser Ablation in Liquid for the Production of Metallic Nanoparticles
What the sources say
- Could not verifycites [40] Wagener, 2010, Laser fragmentation of organic microparticles into colloidal nanoparticles in a free liquid jet, Appl. Phys. A sourceExperimental — accuracy not yet measured
Our copy of Wagener, Philipp & Barcikowski (2010) covers laser fragmentation of melamine cyanurate microcrystals in a free liquid jet, with UV/VIS, DLS and TEM characterization (Abstract; §1 Introduction; §3 Results and discussion); its only mention of plasma is mechanistic — 'a focused laser pulse which generates a plasma and a subsequent shock wave within the microparticles' (§3). No passage addresses optical emission spectroscopy of the laser-induced plasma, atomic spectral lines, or their suppression under liquid confinement versus gaseous expansion (searched: 'absence of atomic spectral lines … liquid confinement', 'plasma emission shielding confining medium density', 'atomic emission lines plasma spectroscopy'). The claim's point is therefore not treated in our copy, neither supported nor contradicted. (LLM, conf=0.72)
- Not checked — no full text of the sourcecites [41] Amendola, 2007, Free Silver Nanoparticles Synthesized by Laser Ablation in Organic Solvents and Their Easy Functionalization, Langmuir source
- Partly supportedcites [42] Chemin, 2019, Doping nanoparticles using pulsed laser ablation in a liquid containing the doping agent, Nanoscale Adv. sourceExperimental — accuracy not yet measured
The Introduction describes a hot, dense plasma produced by laser ablation in liquid. It does not say that this density causes typical atomic spectral lines to be absent. The Experimental section’s LIBS measurements report atomic emission lines, but those measurements were made with argon gas flowing through the plasma region, not in the liquid-confined plume. (LLM, conf=0.78)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Could not verify
The sources with a verdict support this claim; the rest weren’t checked yet, have no full text we could read, or their verdicts aren’t rated yet.
In the paper
“This is strongly indicated by the observed smaller NP diameters at shorter applied wavelengths [54,69,70], which may be the result of fragmentation induced by subsequent laser pulses during batch-LAL.”
§ Nanoparticles Engineering by Pulsed Laser Ablation in Liquids: Concepts and Applications > 2. LAL Synthesis Methods: Principle, Process Parameters and Liquids Effects on Nanoparticle Formation > 2.2. Upscaling of Laser Synthesis of Colloids
What the sources say
- Supportedcites [54] Schwenke, 2011, Influence of processing time on nanoparticle generation during picosecond-pulsed fundamental and second harmonic laser ablation of metals in tetrahydrofuran, Appl. Phys. A source
The Results and discussion section (page unavailable) reports that, for silver colloids, particle diameter decreased more sharply at the shorter wavelength (515 nm) than at 1030 nm. It says the decrease could be attributed to fragmentation of dispersed nanoparticles during post-irradiation, matching the claim's tentative explanation. (LLM, conf=0.89)
- Not checked — no full text of the sourcecites [69] Intartaglia, 2014, Study on the productivity of silicon nanoparticles by picosecond laser ablation in water: Towards gram per hour yield, Opt. Express source
- Not checked — no full text of the sourcecites [70] Kim, 2014, The influence of laser wavelength and fluence on palladium nanoparticles produced by pulsed laser ablation in deionized water, Solid State Sci. source
hedgedstates a possible cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
The sources with a verdict support this claim; the rest weren’t checked yet, have no full text we could read, or their verdicts aren’t rated yet.
In the paper
“The laser wavelength essentially influences the ablation rate in LAL [54,67,68,69,70].”
§ Nanoparticles Engineering by Pulsed Laser Ablation in Liquids: Concepts and Applications > 2. LAL Synthesis Methods: Principle, Process Parameters and Liquids Effects on Nanoparticle Formation > 2.2. Upscaling of Laser Synthesis of Colloids
What the sources say
- Supportedcites [54] Schwenke, 2011, Influence of processing time on nanoparticle generation during picosecond-pulsed fundamental and second harmonic laser ablation of metals in tetrahydrofuran, Appl. Phys. A source
The Results and discussion report that silver ablation at 1030 nm maintained a linear ablation rate, whereas at 515 nm losses of excitation light led to saturation of cumulative ablated mass. The Conclusions likewise identify laser wavelength as a factor in ablation efficiency, while noting that pulse energy, fluence, and colloidal properties also matter. (LLM, conf=0.90)
- Not checked yetcites [67] Tsuji, 2000, Preparation of Metal Colloids by a Laser Ablation Technique in Solution: Influence of Laser Wavelength on the Efficiencies of Colloid Formation, Jpn. J. Appl. Phys. source
Checked before — its earlier verdict is held back until a new check runs.
- Not matchedcites [68] Pfleger, 2007, Laser ablation of silver in aqueous ambient: Effect of laser pulse wavelength and energy on efficiency of the process, J. Physics: Conf. Ser.
Couldn’t be matched to a paper in Crossref, so it can’t be checked.
- Not checked — no full text of the sourcecites [69] Intartaglia, 2014, Study on the productivity of silicon nanoparticles by picosecond laser ablation in water: Towards gram per hour yield, Opt. Express source
- Not checked — no full text of the sourcecites [70] Kim, 2014, The influence of laser wavelength and fluence on palladium nanoparticles produced by pulsed laser ablation in deionized water, Solid State Sci. source
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
179 more claims · 11 with their cited sources checked
Create a free account to see all 316 claims and to verify the 33 references still open.
- It may state two separate claims as one. 94
- The quote only partly states this claim. 5
- Probably not a substantial claim. 43
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Nanoparticles Engineering by Pulsed Laser Ablation in Liquids: Concepts and Applications > 3. Promising Applications of LAL Nanostructures for Biotechnology Applications and for Organic Pollutants Degradation > 3.1. Plasmonic Properties of Metal Nanoparticles and Plasmon Sensitivity
“It has to be noted that Equation (1) is strictly valid only for spherical particles, while for particles with different shapes, the geometry must be taken into account and a plasmon resonance shift can be expected.”
§ Nanoparticles Engineering by Pulsed Laser Ablation in Liquids: Concepts and Applications > 3. Promising Applications of LAL Nanostructures for Biotechnology Applications and for Organic Pollutants Degradation > 3.1. Plasmonic Properties of Metal Nanoparticles and Plasmon Sensitivity
“In this case the polarizability is expressed as:(11)α=4πε0R3ε−εmε+2εm where ε is the dielectric function [ε1(ω)+iε2(ω)] and R the radius of the NP.”
Cited works that were retracted
Works this paper cites that were later retracted, from the retraction notices publishers deposit. Major when the notice came out before this paper was published.
A note, not an issue: for example, a cited work that was retracted only after this paper was published, which its authors could not have known.
In the paper
“The availability of a consistent SERS enhancement in the deep-UV spectral region would therefore allow recording Raman spectra with very low excitation power [190,209], which would be beneficial to reduce photo-degradation issues.”
Cited work 10.1039/c8an00341f · retracted 2021-07-06 · notice 10.1039/d1an90061g · this paper published 2020-11-23
Citations
Cites
1 retracted
Das, R., & Soni, R. K. (2018) · The Analyst · doi:10.1039/c8an00341f · Cited by 11 · cited 1×
“The availability of a consistent SERS enhancement in the deep-UV spectral region would therefore allow recording Raman spectra with very low excitation power [190,209], which would be beneficial to reduce photo-degradation issues.”
BackgroundRetractedElectrochemical Photolysis of Water at a Semiconductor Electrode
FUJISHIMA, A., & HONDA, K. (1972) · Nature · doi:10.1038/238037a0 · Cited by 34,169 · cited 6×
“In the second part of ‘900, after Fujishima and Honda (1972) discussed the photocatalytic water splitting on a TiO2 electrode [242], environmental applications (energy production and degradation of organic pollutants) using solar light and semiconductor oxides became one of the attractive topics of photocatalysis.”
BackgroundInfluentialAbsorption and Scattering of Light by Small Particles
Bohren, C. F., & Huffman, D. R. (1998) · doi:10.1002/9783527618156 · Cited by 18,474
Biosensing with plasmonic nanosensors
Anker, J. N., Hall, W. P., Lyandres, O., Shah, N. C., Zhao, J., & Van Duyne, R. P. (2008) · Nature Materials · doi:10.1038/nmat2162 · Cited by 6,786
Plasmonics beyond the diffraction limit
Gramotnev, D. K., & Bozhevolnyi, S. I. (2010) · Nature Photonics · doi:10.1038/nphoton.2009.282 · Cited by 3,903 · cited 2×
“Much more complex is the situation in all those cases where the NP has a shape far from spherical-like and proper simulations about the plasmonic response should be conducted to interpret the response [142,144,145].”
BackgroundShell-isolated nanoparticle-enhanced Raman spectroscopy
Li, J. F., Huang, Y. F., Ding, Y., Yang, Z. L., Li, S. B., Zhou, X. S., Fan, F. R., Zhang, W., Zhou, Z. Y., Wu, D. Y., et al. (2010) · Nature · doi:10.1038/nature08907 · Cited by 3,559
TiO2 Photocatalysis: A Historical Overview and Future Prospects
Hashimoto, K., Irie, H., & Fujishima, A. (2005) · Japanese Journal of Applied Physics · doi:10.1143/jjap.44.8269 · Cited by 3,367 · cited 1×
“The discovery of photoinduced water splitting together with other results such as photoinduced redox reactions of adsorbed substances on TiO2 by UV irradiation [243] and the decomposition of CN− ions in UV-irradiated aqueous TiO2 suspensions [244] have significantly expanded the field of application of TiO2 based phot…”
BackgroundReview on nanoparticles and nanostructured materials: history, sources, toxicity and regulations
Jeevanandam, J., Barhoum, A., Chan, Y. S., Dufresne, A., & Danquah, M. K. (2018) · Beilstein Journal of Nanotechnology · doi:10.3762/bjnano.9.98 · Cited by 3,297 · cited 1×
“, edible and nontoxic nano-delivery systems, or effective formulations that are safe for human consumption and drug treatments [22].”
BackgroundDecontamination and disinfection of water by solar photocatalysis: Recent overview and trends
Malato, S., Fernández-Ibáñez, P., Maldonado, M. I., Blanco, J., & Gernjak, W. (2009) · Catalysis Today · doi:10.1016/j.cattod.2009.06.018 · Cited by 3,004 · cited 3×
“The main redox reactions are summarized by Horikoshi and Malato [250,251] as follows: e− + O2 → O−·2 O−·2 (ads) + H + → HO·2(ads) h+ + H2O→ ·OH(ads) + H+ h+ + O−·2 (ads)→ 2O·(ads) h+ + P→ P·+ (14) Then, oxygen and pollutant radicals further react to give oxidation of organic products.”
BackgroundHeberer, T. (2002) · Toxicology Letters · doi:10.1016/s0378-4274(02)00041-3 · Cited by 2,995
Research works printed but not linked: 10
- Stafe, 2010, Pulsed laser ablation of solids, Rom. Rep. Phys., 62, 758
- Hamid, 2015, Electric field effect on the synthesis of nanogold particles by PLAL, Int. J. Chem. Nat. Sci., 3, 269
- Santoro, M., Fazio, E., Trusso, S., Ossi, P.M., Tommasini, M., and Neri, F. (2016, January 14–16). Rhodium nanoparticles synthesized by nanosecond and picosecond Pulsed Laser Ablation in Liquid. GISR2016. Proceedings of the Italian Meeting on Raman Spectroscopy and Non Linear Optic Effects, Padova, Italy.
- Santoro, M., Bertoncini, A., Fazio, E., Tommasini, M., Neri, F., Ossi, P.M., and Trusso, S. (2018, January 21–23). Nanostructured Rhodium Thin Films Deposited by Pulsed Laser Deposition for SERS Detection. CNS2018—4°. Proceedings of the Congresso Nazionale Sensori, Catania, Italy.
- Wang, 2005, Effects of dopant states on photoactivity in carbon-doped TiO2, J. Physics: Condens. Matter, 17, L209
- Eibner, 1911, Action of Light on Pigments, Chem. Ztg., 35, 753
- Keidel, 1929, The Fading of Aniline Dyes in the Presence of Titanium White, Farben Ztg., 34, 1242
- Osugi, 1936, On the photoxidation of ammonium compounds in solution and soil, Jpn. J. Soil Manure., 10, 11
- Frenkel, 1936, On the Absorption of Light and the Trapping of Electrons and Positive Holes in Crystalline Dielectrics, Phys. Zs. Sowjetunion., 9, 158
- Negrea, 2008, Stuies regarding the Benzene, Toluene and o-Xylene Removal from Waste Water, Politeh. Univ., 53, 1
Cited by
Fazio, E., Spadaro, S., Corsaro, C., Neri, G., Leonardi, S. G., Neri, F., Lavanya, N., Sekar, C., Donato, N., & Neri, G. (2021) · Sensors · doi:10.3390/s21072494 · Cited by 274
Self-citationZoubi, W. A., Putri, R. A. K., Abukhadra, M. R., & Ko, Y. G. (2023) · Nano Energy · doi:10.1016/j.nanoen.2023.108362 · Cited by 142
Yogesh, G. K., Shukla, S., Sastikumar, D., & Koinkar, P. (2021) · Applied Physics A · doi:10.1007/s00339-021-04951-6 · Cited by 148
Khairani, I. Y., Mínguez-Vega, G., Doñate-Buendía, C., & Gökce, B. (2023) · Physical Chemistry Chemical Physics · doi:10.1039/d3cp01214j · Cited by 130
Self-citationSynergistic antibacterial mechanism of silver-copper bimetallic nanoparticles
Hao, Z., Wang, M., Cheng, L., Si, M., Feng, Z., & Feng, Z. (2024) · Frontiers in Bioengineering and Biotechnology · doi:10.3389/fbioe.2023.1337543 · Cited by 125
“Compared to several prevalent manufacturing techniques, PLAL offers faster production of BNPs and effective control over the size distribution, yield, and shape of nanoparticles (Fazio et al., 2020; Nyabadza et al., 2023).”
Method
Metadata
- Authors
- Fazio, E., Gökce, B., De Giacomo, A., Meneghetti, M., Compagnini, G., Tommasini, M., Waag, F., Lucotti, A., Zanchi, C. G., Ossi, P. M., Dell’Aglio, M., D’Urso, L., Condorelli, M., Scardaci, V., Biscaglia, F., Litti, L., Gobbo, M., Gallo, G., Santoro, M., Trusso, S., & Neri, F.
- Affiliations
- University of Messina (IT)
- University of Duisburg-Essen (DE)
- Department of Chemistry, University of Bari, Via Orabona 4, 70126 Bari, Italy
- University of Padua (IT)
- University of Catania (IT)
- Politecnico di Milano (IT)
- Istituto di Nanotecnologia (IT)
- STMicroelectronics (Italy) (IT)
- Institute for Chemical and Physical Processes (IT)
- Corresponding author
- Fazio, Enza
- ORCID
- Fazio, Enza
- Gökce, Bilal
- De Giacomo, Alessandro
- Meneghetti, Moreno
- Compagnini, Giuseppe
- Tommasini, Matteo
- Waag, Friedrich
- Lucotti, Andrea
- Zanchi, Chiara Giuseppina
- Ossi, Paolo Maria
- Dell’Aglio, Marcella
- D’Urso, Luisa
- Condorelli, Marcello
- Scardaci, Vittorio
- Litti, Lucio
- Gobbo, Marina
- Gallo, Giovanni
- Trusso, Sebastiano
- Neri, Fortunato
- Venue
- Nanomaterials
- Publisher
- MDPI AG
- Published
- 2020-11-23
- Volume
- 10
- Issue
- 11
- Pages
- 2317
- ISSN
- 2079-4991 (ISSN-L)
- PMC
- PMC7700616
- OpenAlex
- W3108657096
- Cited by
- 346
- References
- 288
- Citations by year
- 2026: 62 · 2025: 83 · 2024: 65 · 2023: 66 · 2022: 45 · 2021: 24
- FWCI
- 2.82
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Nanomaterials (publishedVersion, cc-by)
- PubMed Central (publishedVersion, cc-by)
- PubMed (publishedVersion)
- Virtual Community of Pathological Anatomy (University of Castilla La Mancha) (submittedVersion, other-oa)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- CINECA IRIS Institutional Research Information System (University of Bari Aldo Moro) (submittedVersion)
- Padua Research Archive (University of Padova) (submittedVersion, cc-by)
- Funders
- Università degli Studi di Padova (04SID2016, 08SID2017)
- Topics
- Physical Sciences › Materials Science › Materials Chemistry › Laser-Ablation Synthesis of Nanoparticles
- Physical Sciences › Physics and Astronomy › Acoustics and Ultrasonics › Ultrasound and Cavitation Phenomena
- Physical Sciences › Materials Science › Electronic, Optical and Magnetic Materials › Gold and Silver Nanoparticles Synthesis and Applications
- Keywords
- pulsed laser ablation in liquid, laser synthesis, ligand-free nanoparticles, nanocolloids, functionalized nanomaterials, scalable nanoparticle synthesis, biomedical applications, catalysis, sensing, energy applications, environmental applications
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol and qwen3.8-omni-flash).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
How to cite
Cite CoChat for the checks on this page, and the paper for its own findings.
- This page
- CoChat. (2026). Citation check: Nanoparticles Engineering by Pulsed Laser Ablation in Liquids: Concepts and Applications. https://app.cochat.ai/papers/10.3390/nano10112317
- The paper
- Fazio, E., Gökce, B., De Giacomo, A., Meneghetti, M., Compagnini, G., Tommasini, M., Waag, F., Lucotti, A., Zanchi, C. G., Ossi, P. M., Dell’Aglio, M., D’Urso, L., Condorelli, M., Scardaci, V., Biscaglia, F., Litti, L., Gobbo, M., Gallo, G., Santoro, M., . . . Neri, F. (2020). Nanoparticles Engineering by Pulsed Laser Ablation in Liquids: Concepts and Applications. Nanomaterials. https://doi.org/10.3390/nano10112317
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.