The DOI matches its Crossref record; 60 of the 60 references it cites were found in a registry or an index.
Microstructural porosity in additive manufacturing: The formation and detection of pores in metal parts fabricated by powder bed fusion
Open accessAbstract
Metal additive manufacturing (AM) is an innovative manufacturing technique that can build complex and high value metal parts layer by layer using a computerized three‐dimensional solid model. Powder bed fusion (PBF) is one of the most common AM techniques. It sequentially processes a powdered feedstock in thin layers and solidifies it by either a laser beam or an electron beam. However, PBF induces microstructural defects that can adversely affect the performance of the manufactured components. These undesirable defects including voids and porosities must be avoided or minimized to limit their negative effects on mechanical properties and to ensure the consistency and repeatability of AM parts. The present article provides an overview of the formation mechanisms of pores in AM metals and some emerging techniques for the detection and quantification of pores. The review also highlights other common defects in PBF parts such as microstructural features associated with keyhole mode of melting.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Additive Manufacturing Technologies: Rapid Prototyping to Direct Digital Manufacturing
Gibson, I., Rosen, D. W., & Stucker, B. (2010) · National University of Singapore · doi:10.1007/978-1-4419-1120-9 · Cited by 2,969
A study of the microstructural evolution during selective laser melting of Ti–6Al–4V
Thijs, L., Verhaeghe, F., Craeghs, T., Humbeeck, J. V., & Kruth, J.-P. (2010) · Acta Materialia · doi:10.1016/j.actamat.2010.02.004 · Cited by 2,929
Khairallah, S. A., Anderson, A. T., Rubenchik, A., & King, W. E. (2016) · Acta Materialia · doi:10.1016/j.actamat.2016.02.014 · Cited by 2,766
The metallurgy and processing science of metal additive manufacturing
Sames, W. J., List, F. A., Pannala, S., Dehoff, R. R., & Babu, S. S. (2016) · International Materials Reviews · doi:10.1080/09506608.2015.1116649 · Cited by 2,529
Residual stresses in selective laser sintering and selective laser melting
Mercelis, P., & Kruth, J. (2006) · Rapid Prototyping Journal · doi:10.1108/13552540610707013 · Cited by 2,015
Thijs, L., Kempen, K., Kruth, J.-P., & Van Humbeeck, J. (2013) · Acta Materialia · doi:10.1016/j.actamat.2012.11.052 · Cited by 1,917
Observation of keyhole-mode laser melting in laser powder-bed fusion additive manufacturing
King, W. E., Barth, H. D., Castillo, V. M., Gallegos, G. F., Gibbs, J. W., Hahn, D. E., Kamath, C., & Rubenchik, A. M. (2014) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2014.06.005 · Cited by 1,616
Vilaro, T., Colin, C., & Bartout, J. D. (2011) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-011-0731-y · Cited by 1,283
Reducing porosity in AlSi10Mg parts processed by selective laser melting
Aboulkhair, N. T., Everitt, N. M., Ashcroft, I., & Tuck, C. (2014) · Additive Manufacturing · doi:10.1016/j.addma.2014.08.001 · Cited by 1,281
Read, N., Wang, W., Essa, K., & Attallah, M. M. (2015) · Materials & Design (1980-2015) · doi:10.1016/j.matdes.2014.09.044 · Cited by 1,218
Brandl, E., Heckenberger, U., Holzinger, V., & Buchbinder, D. (2012) · Materials & Design · doi:10.1016/j.matdes.2011.07.067 · Cited by 1,151
Gu, D., Hagedorn, Y.-C., Meiners, W., Meng, G., Batista, R. J. S., Wissenbach, K., & Poprawe, R. (2012) · Acta Materialia · doi:10.1016/j.actamat.2012.04.006 · Cited by 1,089
Gong, H., Rafi, K., Gu, H., Starr, T., & Stucker, B. (2014) · Additive Manufacturing · doi:10.1016/j.addma.2014.08.002 · Cited by 1,038
Mechanical behavior of additive manufactured, powder-bed laser-fused materials
Mower, T. M., & Long, M. J. (2016) · Materials Science and Engineering: A · doi:10.1016/j.msea.2015.10.068 · Cited by 1,001
Gong, H., Rafi, K., Gu, H., Janaki Ram, G. D., Starr, T., & Stucker, B. (2015) · Materials & Design · doi:10.1016/j.matdes.2015.07.147 · Cited by 940
Defect formation mechanisms in selective laser melting: a review
Zhang, B., Li, Y., & Bai, Q. (2017) · Chinese Journal of Mechanical Engineering · doi:10.1007/s10033-017-0121-5 · Cited by 924
Process defects and in situ monitoring methods in metal powder bed fusion: a review
Grasso, M., & Colosimo, B. M. (2017) · Measurement Science and Technology · doi:10.1088/1361-6501/aa5c4f · Cited by 833
Lasers and materials in selective laser sintering
Kruth, J. P., Wang, X., Laoui, T., & Froyen, L. (2003) · Assembly Automation · doi:10.1108/01445150310698652 · Cited by 826
Qiu, C., Adkins, N. J. E., & Attallah, M. M. (2013) · Materials Science and Engineering: A · doi:10.1016/j.msea.2013.04.099 · Cited by 821
A Review on Process Monitoring and Control in Metal-Based Additive Manufacturing
Tapia, G., & Elwany, A. (2014) · Journal of Manufacturing Science and Engineering · doi:10.1115/1.4028540 · Cited by 711
Dynamics of pore formation during laser powder bed fusion additive manufacturing
Martin, A. A., Calta, N. P., Khairallah, S. A., Wang, J., Depond, P. J., Fong, A. Y., Thampy, V., Guss, G. M., Kiss, A. M., Stone, K. H., et al. (2019) · Nature Communications · doi:10.1038/s41467-019-10009-2 · Cited by 711
Additive layered manufacturing: sectors of industrial application shown through case studies
Petrovic, V., Vicente Haro Gonzalez, J., Jordá Ferrando, O., Delgado Gordillo, J., Ramón Blasco Puchades, J., & Portolés Griñan, L. (2011) · International Journal of Production Research · doi:10.1080/00207540903479786 · Cited by 676
High Power Selective Laser Melting (HP SLM) of Aluminum Parts
Buchbinder, D., Schleifenbaum, H., Heidrich, S., Meiners, W., & Bültmann, J. (2011) · Physics Procedia · doi:10.1016/j.phpro.2011.03.035 · Cited by 666
Comparison of density measurement techniques for additive manufactured metallic parts
Spierings, A. B., Schneider, M., & Eggenberger, R. (2011) · Rapid Prototyping Journal · doi:10.1108/13552541111156504 · Cited by 613
Yu, W. H., Sing, S. L., Chua, C. K., Kuo, C. N., & Tian, X. L. (2019) · Progress in Materials Science · doi:10.1016/j.pmatsci.2019.04.006 · Cited by 586
Formation and reduction of hydrogen porosity during selective laser melting of AlSi10Mg
Weingarten, C., Buchbinder, D., Pirch, N., Meiners, W., Wissenbach, K., & Poprawe, R. (2015) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2015.02.013 · Cited by 585
Oxides, porosity and fatigue performance of AlSi10Mg parts produced by selective laser melting
Ming, T., & Pistorius, P. C. (2016) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2016.06.002 · Cited by 487
Physical Aspects of Process Control in Selective Laser Sintering of Metals
Das, S. (2003) · Advanced Engineering Materials · doi:10.1002/adem.200310099 · Cited by 434
Porosity Measurements and Analysis for Metal Additive Manufacturing Process Control
Slotwinski, J. A., Garboczi, E. J., & Hebenstreit, K. M. (2014) · Journal of Research of the National Institute of Standards and Technology · doi:10.6028/jres.119.019 · Cited by 408
Defect generation and propagation mechanism during additive manufacturing by selective beam melting
Bauereiß, A., Scharowsky, T., & Körner, C. (2014) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2014.05.002 · Cited by 351
Porosity prediction: Supervised-learning of thermal history for direct laser deposition
Khanzadeh, M., Chowdhury, S., Marufuzzaman, M., Tschopp, M. A., & Bian, L. (2018) · Journal of Manufacturing Systems · doi:10.1016/j.jmsy.2018.04.001 · Cited by 338
The effect of powder oxidation on defect formation in laser additive manufacturing
Leung, C. L. A., Marussi, S., Towrie, M., Atwood, R. C., Withers, P. J., & Lee, P. D. (2019) · Acta Materialia · doi:10.1016/j.actamat.2018.12.027 · Cited by 336
Additive Manufacturing of Metals
Milewski, J. O. (2017) · Springer series in materials science · doi:10.1007/978-3-319-58205-4 · Cited by 332
Fundamental consolidation mechanisms during selective beam melting of powders
Körner, C., Bauereiß, A., & Attar, E. (2013) · Modelling and Simulation in Materials Science and Engineering · doi:10.1088/0965-0393/21/8/085011 · Cited by 323
Maskery, I., Aboulkhair, N. T., Corfield, M. R., Tuck, C., Clare, A. T., Leach, R. K., Wildman, R. D., Ashcroft, I. A., & Hague, R. J. M. (2016) · Materials Characterization · doi:10.1016/j.matchar.2015.12.001 · Cited by 317
Functionally graded materials for orthopedic applications – an update on design and manufacturing
Sola, A., Bellucci, D., & Cannillo, V. (2016) · Biotechnology Advances · doi:10.1016/j.biotechadv.2015.12.013 · Cited by 314
Self-citationGas flow effects on selective laser melting (SLM) manufacturing performance
Ferrar, B., Mullen, L., Jones, E., Stamp, R., & Sutcliffe, C. J. (2012) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2011.09.020 · Cited by 302
Seifi, M., Salem, A. A., Satko, D. P., Shaffer, J., & Lewandowski, J. J. (2016) · International Journal of Fatigue · doi:10.1016/j.ijfatigue.2016.06.001 · Cited by 291
Defects-dictated tensile properties of selective laser melted Ti-6Al-4V
Voisin, T., Calta, N. P., Khairallah, S. A., Forien, J., Balogh, L., Cunningham, R., Rollett, A. D., & Wang, Y. (2018) · Materials & Design · doi:10.1016/j.matdes.2018.08.004 · Cited by 277
Cunningham, R., Nicolas, A., Madsen, J., Fodran, E., Anagnostou, E., Sangid, M. D., & Rollett, A. D. (2017) · Materials Research Letters · doi:10.1080/21663831.2017.1340911 · Cited by 259
Yang, K. V., Rometsch, P., Davies, C. H. J., Huang, A., & Wu, X. (2018) · Materials & Design · doi:10.1016/j.matdes.2018.05.026 · Cited by 243
Metal Alloys for Fusion‐Based Additive Manufacturing
Zhang, D., Sun, S., Qiu, D., Gibson, M. A., Dargusch, M. S., Brandt, M., Qian, M., & Easton, M. A. (2018) · Advanced Engineering Materials · doi:10.1002/adem.201700952 · Cited by 236
Malekipour, E., & El-Mounayri, H. (2018) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-017-1172-6 · Cited by 230
On the role of thermal fluid dynamics into the evolution of porosity during selective laser melting
Panwisawas, C., Qiu, C. L., Sovani, Y., Brooks, J. W., Attallah, M. M., & Basoalto, H. C. (2015) · Scripta Materialia · doi:10.1016/j.scriptamat.2015.04.016 · Cited by 228
Additive Manufacturing of Metals: The Technology, Materials, Design and Production
Yang, L., Hsu, K., Baughman, B., Godfrey, D., Medina, F., Menon, M., & Wiener, S. (2017) · Springer Series in Advanced Manufacturing · doi:10.1007/978-3-319-55128-9 · Cited by 215
Young’s modulus and volume porosity relationships for additive manufacturing applications
Choren, J. A., Heinrich, S. M., & Silver-Thorn, M. B. (2013) · Journal of Materials Science · doi:10.1007/s10853-013-7237-5 · Cited by 208
Prithivirajan, V., & Sangid, M. D. (2018) · Materials & Design · doi:10.1016/j.matdes.2018.04.022 · Cited by 204
Åsberg, M., Fredriksson, G., Hatami, S., Fredriksson, W., & Krakhmalev, P. (2019) · Materials Science and Engineering: A · doi:10.1016/j.msea.2018.08.046 · Cited by 184
Olakanmi, E. O., Cochrane, R. F., & Dalgarno, K. W. (2011) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2010.09.003 · Cited by 171
Kim, F. H., Moylan, S. P., Garboczi, E. J., & Slotwinski, J. A. (2017) · Additive manufacturing · doi:10.1016/j.addma.2017.06.011 · Cited by 126
Tong, J., Bowen, C., Persson, J., & Plummer, A. R. (2016) · Materials Science and Technology · doi:10.1080/02670836.2016.1172787 · Cited by 115
Iebba, M., Astarita, A., Mistretta, D., Colonna, I., Liberini, M., Scherillo, F., Pirozzi, C., Borrelli, R., Franchitti, S., & Squillace, A. (2017) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-017-2796-2 · Cited by 96
Morrow, B., Lienert, T. J., Knapp, C., Sutton, J. O., Brand, M. J., Pacheco, R. M., Livescu, V., Carpenter, J. S., & Gray, G. T., III (2018) · Metallurgical and Materials Transactions A · doi:10.1007/s11661-018-4661-9 · Cited by 90
Study on Shrinkage Behaviour of Direct Laser Sintering Metallic Powder
Zhu, H. H., Lü, L., & Fuh, J. Y. H. (2006) · Proceedings of the Institution of Mechanical Engineers Part B Journal of Engineering Manufacture · doi:10.1243/095440505x32995 · Cited by 87
Scanning optical microscopy for porosity quantification of additively manufactured components
Wang, P., Tan, X., He, C., Nai, M. L. S., Huang, R., Tor, S. B., & Wei, J. (2018) · Additive manufacturing · doi:10.1016/j.addma.2018.03.019 · Cited by 70
Brandão, A. D., Gerard, R., Gumpinger, J., Beretta, S., Makaya, A., Pambaguian, L., & Ghidini, T. (2017) · Materials · doi:10.3390/ma10050522 · Cited by 69
Porosity of additive manufacturing parts for process monitoring
Slotwinski, J. A., & Garboczi, E. J. (2014) · AIP conference proceedings · doi:10.1063/1.4864957 · Cited by 64
Ngnekou, J. N. D., Nadot, Y., Hénaff, G., Nicolaï, J., & Ridosz, L. (2017) · Procedia Structural Integrity · doi:10.1016/j.prostr.2017.11.063 · Cited by 61
Titanium foam scaffolds for dental applications
Nouri, A. (2016) · Elsevier eBooks · doi:10.1016/b978-0-08-101289-5.00005-6 · Cited by 34
Self-citationIgarashi, T. (2016) · Seikei-Kakou · doi:10.4325/seikeikakou.28.288 · Cited by 28
Cited by
Metal additive manufacturing in aerospace: A review
Blakey-Milner, B., Gradl, P., Snedden, G., Brooks, M., Pitot, J., Lopez, E., Leary, M., Berto, F., & du Plessis, A. (2021) · Materials & Design · doi:10.1016/j.matdes.2021.110008 · Cited by 2,263
Khan, N., & Riccio, A. (2024) · Progress in Aerospace Sciences · doi:10.1016/j.paerosci.2024.101021 · Cited by 486
Al-Maharma, A. Y., Patil, S. P., & Markert, B. (2020) · Materials Research Express · doi:10.1088/2053-1591/abcc5d · Cited by 404
Mukherjee, T., Elmer, J. W., Wei, H. L., Lienert, T. J., Zhang, W., Kou, S., & DebRoy, T. (2023) · Progress in Materials Science · doi:10.1016/j.pmatsci.2023.101153 · Cited by 267
Post-Process Treatments for Additive-Manufactured Metallic Structures: A Comprehensive Review
Ge, J., Pillay, S., & Ning, H. (2023) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-023-08051-9 · Cited by 157
Metadata
- Authors
- Sola, A., & Nouri, A.
- Venue
- Journal of Advanced Manufacturing and Processing
- Publisher
- Wiley
- Published
- 2019-06-28
- Volume
- 1
- Issue
- 3
- ISSN
- 2637-403X (ISSN-L)
- OpenAlex
- W2954552741
- Cited by
- 378
- References
- 60
- FWCI
- 18.42
- Type
- journal article
- Language
- en
- Open access
- green
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.