The DOI matches its Crossref record; 44 of the 44 references it cites were found in a registry or an index.
The effect of processing parameters on the mechanical characteristics of PLA produced by a 3D FFF printer
Open accessAbstract
3D printing by fused filament fabrication (FFF) provides an innovative manufacturing method for complex geometry components. Since FFF is a layered manufacturing process, effects of process parameters are of concern when plastic materials such as polylactic acid (PLA), polystyrene and nylon are used. This study explores how the process parameters, e.g. build orientation and infill pattern/density, affect the mechanical response of PLA samples produced using FFF. Digital image correlation (DIC) was employed to get full-field surface-strain measurements. The results show the influence of build orientation and infill density is significant. For on-edge orientation, the tensile strength and Young’s modulus were 55 MPa and 3.5 GPa respectively, which were about 91% and 40% less for the upright orientation, demonstrating a significant anisotropy. The tensile strength and Young’s modulus increased with increasing infill density. In contrast, different infill patterns have no significant effect. Considering the influence of build orientation, based on the experimental results, a constitutive model derived from the laminate plate theory was employed. The material parameters were determined by tensile tests. Results demonstrated a reasonable agreement between the experimental data and the predictive model. Similar anisotropy to tension was observed in shear tests; shear modulus and shear strength for 45° flat orientation were about 1.55 GPa and 36 MPa, whereas for upright specimens they were about 0.95 GPa and 18 MPa, respectively. The findings provide a framework for systematic mechanical characterisation of 3D-printed polymers and potential ways of choosing process parameters to maximise performance for a given design.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Mechanics of laminated composite plates and shells : theory and analysis
Reddy, J. N. (2004) · Cited by 4,797
Mechanics of Laminated Composite Plates and Shells
Reddy, J. N. (2003) · CRC Press eBooks · doi:10.1201/b12409 · Cited by 3,845
Anisotropic material properties of fused deposition modeling ABS
Ahn, S., Montero, M., Odell, D., Roundy, S., & Wright, P. K. (2002) · Rapid Prototyping Journal · doi:10.1108/13552540210441166 · Cited by 2,382
Chacón, J. M., Caminero, M. A., García-Plaza, E., & Núñez, P. J. (2017) · Materials & Design · doi:10.1016/j.matdes.2017.03.065 · Cited by 1,603
Mechanical characterization of 3D-printed polymers
Dizon, J. R. C., Espera, A. H., Chen, Q., & Advincula, R. C. (2018) · Additive Manufacturing · doi:10.1016/j.addma.2017.12.002 · Cited by 1,340
Parametric appraisal of mechanical property of fused deposition modelling processed parts
Sood, A. K., Ohdar, R. K., & Mahapatra, S. S. (2010) · Materials & Design · doi:10.1016/j.matdes.2009.06.016 · Cited by 1,318
Hild, F., & Roux, S. (2006) · Strain · doi:10.1111/j.1475-1305.2006.00258.x · Cited by 1,188
Wu, W., Geng, P., Li, G., Zhao, D., Zhang, H., & Zhao, J. (2015) · Materials · doi:10.3390/ma8095271 · Cited by 881
Application of an optimized digital correlation method to planar deformation analysis
Sutton, M., Mingqi, C., Peters, W., Chao, Y., & McNeill, Sr. (1986) · Image and Vision Computing · doi:10.1016/0262-8856(86)90057-0 · Cited by 724
Lanzotti, A., Grasso, M., Staiano, G., & Martorelli, M. (2015) · Rapid Prototyping Journal · doi:10.1108/rpj-09-2014-0135 · Cited by 684
Paolini, A., Kollmannsberger, S., & Rank, E. (2019) · Additive Manufacturing · doi:10.1016/j.addma.2019.100894 · Cited by 673
Ning, F., Cong, W., Hu, Y., & Wang, H. (2017) · Journal of Composite Materials · doi:10.1177/0021998316646169 · Cited by 632
Measurements of the mechanical response of unidirectional 3D-printed PLA
Song, Y., Li, Y., Song, W., Yee, K., Lee, K.-Y., & Tagarielli, V. L. (2017) · Materials & Design · doi:10.1016/j.matdes.2017.03.051 · Cited by 624
Additive construction: State-of-the-art, challenges and opportunities
Labonnote, N., Rønnquist, A., Manum, B., & Rüther, P. (2016) · Automation in Construction · doi:10.1016/j.autcon.2016.08.026 · Cited by 607
Optimization of rapid prototyping parameters for production of flexible ABS object
Lee, B. H., Abdullah, J. M., & Khan, Z. A. (2005) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2005.02.259 · Cited by 578
Mechanical property characterization and simulation of fused deposition modeling Polycarbonate parts
Domingo-Espin, M., Puigoriol-Forcada, J. M., Garcia-Granada, A.-A., Llumà, J., Borros, S., & Reyes, G. (2015) · Materials & Design · doi:10.1016/j.matdes.2015.06.074 · Cited by 535
Durgun, I., & Ertan, R. (2014) · Rapid Prototyping Journal · doi:10.1108/rpj-10-2012-0091 · Cited by 530
Measurement of anisotropic compressive strength of rapid prototyping parts
Lee, C. S., Kim, S. G., Kim, H. J., & Ahn, S. (2007) · Journal of Materials Processing Technology · doi:10.1016/j.jmatprotec.2006.11.095 · Cited by 504
Casavola, C., Cazzato, A., Moramarco, V., & Pappalettere, C. (2015) · Materials & Design · doi:10.1016/j.matdes.2015.11.009 · Cited by 493
Recent Advances in Bioink Design for 3D Bioprinting of Tissues and Organs
Ji, S., & Guvendiren, M. (2017) · Frontiers in Bioengineering and Biotechnology · doi:10.3389/fbioe.2017.00023 · Cited by 490
Rankouhi, B., Javadpour, S., Delfanian, F., & Letcher, T. (2016) · Journal of Failure Analysis and Prevention · doi:10.1007/s11668-016-0113-2 · Cited by 457
Experimental characterization of the mechanical properties of 3D-printed ABS and polycarbonate parts
Cantrell, J. T., Rohde, S., Damiani, D., Gurnani, R., DiSandro, L., Anton, J., Young, A., Jerez, A., Steinbach, D., Kroese, C., et al. (2017) · Rapid Prototyping Journal · doi:10.1108/rpj-03-2016-0042 · Cited by 433
Mechanical behavior of acrylonitrile butadiene styrene fused deposition materials modeling
Matas, J. F. R., Thomas, J. P., & Renaud, J. E. (2003) · Rapid Prototyping Journal · doi:10.1108/13552540310489604 · Cited by 388
Anisotropic Mechanical Properties of ABS Parts Fabricated by Fused Deposition Modelling
Ziemian, C., Sharma, M., & Ziemi, S. (2012) · Mechanical Engineering · doi:10.5772/34233 · Cited by 387
Isotropic and anisotropic elasticity and yielding of 3D printed material
Zou, R. X., Xia, Y., Liu, S., Hu, P., Hou, W., Hu, Q., & Shan, C. (2016) · Composites Part B Engineering · doi:10.1016/j.compositesb.2016.06.009 · Cited by 358
Ghaffar, S. H., Corker, J., & Fan, M. (2018) · Automation in Construction · doi:10.1016/j.autcon.2018.05.005 · Cited by 358
Effects of layer thickness and binder saturation level parameters on 3D printing process
Vaezi, M., & Chua, C. K. (2011) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-010-2821-1 · Cited by 341
Frontiers of 3D Printing/Additive Manufacturing: from Human Organs to Aircraft Fabrication
Murr, L. E. (2016) · Journal of Material Science and Technology · doi:10.1016/j.jmst.2016.08.011 · Cited by 329
Material Property Testing of 3D-Printed Specimen in PLA on an Entry-Level 3D Printer
Letcher, T., & Waytashek, M. (2014) · Volume 2A: Advanced Manufacturing · doi:10.1115/imece2014-39379 · Cited by 325
Akhoundi, B., & Behravesh, A. H. (2019) · Experimental Mechanics · doi:10.1007/s11340-018-00467-y · Cited by 297
Additive manufacturing of custom orthoses and prostheses—A review
Chen, R. K., Jin, Y.-A., Wensman, J., & Shih, A. (2016) · Additive Manufacturing · doi:10.1016/j.addma.2016.04.002 · Cited by 292
Torrado, A. R., & Roberson, D. A. (2016) · Journal of Failure Analysis and Prevention · doi:10.1007/s11668-016-0067-4 · Cited by 291
Farzadi, A., Solati-Hashjin, M., Asadi-Eydivand, M., & Abu Osman, N. A. (2014) · PLoS ONE · doi:10.1371/journal.pone.0108252 · Cited by 284
Zaldivar, R. J., Witkin, D. B., McLouth, T., Patel, D. N., Schmitt, K., & Nokes, J. P. (2017) · Additive Manufacturing · doi:10.1016/j.addma.2016.11.007 · Cited by 277
Onwubolu, G. C., & Rayegani, F. (2014) · International Journal of Manufacturing Engineering · doi:10.1155/2014/598531 · Cited by 252
Deposition direction-dependent failure criteria for fused deposition modeling polycarbonate
Hill, N., & Haghi, M. (2014) · Rapid Prototyping Journal · doi:10.1108/rpj-04-2013-0039 · Cited by 181
Dave, H. K., Patadiya, N. H., Prajapati, A. R., & Rajpurohit, S. R. (2019) · Proceedings of the Institution of Mechanical Engineers Part C Journal of Mechanical Engineering Science · doi:10.1177/0954406219856383 · Cited by 159
Panda, S. K., Padhee, S., Sood, A. K., & Mahapatra, S. S. (2009) · Intelligent Information Management · doi:10.4236/iim.2009.12014 · Cited by 150
Ulu, E., Korkmaz, E., Yay, K., Özdoğanlar, O. B., & Kara, L. B. (2015) · Journal of Mechanical Design · doi:10.1115/1.4030998 · Cited by 132
Towards Single-Step Biofabrication of Organs on a Chip via 3D Printing
Knowlton, S. M., Yenilmez, B., & Taşoğlu, S. (2016) · Trends in biotechnology · doi:10.1016/j.tibtech.2016.06.005 · Cited by 117
Structure–mechanical property relationship in fused deposition modelling
Rezayat, H., Zhou, W., Siriruk, A., Penumadu, D., & Babu, S. S. (2015) · Materials Science and Technology · doi:10.1179/1743284715y.0000000010 · Cited by 107
3D printing for drug manufacturing: A perspective on the future of pharmaceuticals
Lepowsky, E., & Taşoğlu, S. (2017) · International Journal of Bioprinting · doi:10.18063/ijb.v1i1.119 · Cited by 103
Failure analysis of 3D printed glass fiber/PA12 composite lattice structures using DIC
Hao, W., Liu, Y., Wang, T., Guo, G., Chen, H., & Fang, D. (2019) · Composite Structures · doi:10.1016/j.compstruct.2019.111192 · Cited by 72
Additive Manufacturing of Aerospace Alloys for Aircraft Structures
Kobryn, P. A., Ontko, N. R., Perkins, L., & Tiley, J. (2006) · Cited by 69
Cited by
Ghorbani, J., Koirala, P., Shen, Y.-L., & Tehrani, M. (2022) · Journal of Manufacturing Processes · doi:10.1016/j.jmapro.2022.06.026 · Cited by 115
Ahmed, R., Dola, I. S., Ahmed, S., Rahman, M. M., Shanto, T. A., & Taylor, R. (2026) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-026-18078-6 · Cited by 6
Metadata
- Authors
- Gonabadi, H., Yadav, A., & Bull, S. J.
- Venue
- The International Journal of Advanced Manufacturing Technology
- Published
- 2020-10-02
- Volume
- 111
- Issue
- 3-4
- Pages
- 695-709
- ISSN
- 0268-3768 (ISSN-L)
- 1433-3015
- OpenAlex
- W3089973426
- Cited by
- 256
- References
- 44
- FWCI
- 9.09
- Type
- journal article
- Language
- en
- Open access
- hybrid
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.