KCl Induced Corrosion of a 304-type Austenitic Stainless Steel at 600°C; The Role of Potassium
The DOI matches its Crossref record; 22 of the 22 references it cites were found in a registry or an index.
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“Potassium chloride may then condense on particles in the flue gas or on surfaces, forming a corrosive deposit. 6,11,12”
From Potassium, Chlorine, and Sulfur in Ash, Particles, Deposits, and Corrosion during Wood Combustion in a Circulating Fluidized-Bed Boiler (2007) · cites this paper as [11]
In the citing paper
“Once a deposit including alkali metals has been formed, corrosion may be enhanced 6,11,12 and the super heater tubes may have to be replaced, implying costly shutdown and repair.”
From Potassium, Chlorine, and Sulfur in Ash, Particles, Deposits, and Corrosion during Wood Combustion in a Circulating Fluidized-Bed Boiler (2007) · cites this paper as [11]
In the citing paper
“Exposures of alloy 304 and Sanicro 28 to an O2 + H2O environment in the presence of KCl (s) at 600 C showed that KCl reacts with the protective (Cr,Fe)2O3 oxide according to reaction 2, forming K2CrO4 and poorly protective Fe2O3: 11,12”
From Potassium, Chlorine, and Sulfur in Ash, Particles, Deposits, and Corrosion during Wood Combustion in a Circulating Fluidized-Bed Boiler (2007) · cites this paper as [11]
In the citing paper
“The reaction depletes the oxide in chromium and was reported to trigger rapid oxidation of the alloy, similar to the depletion caused by CrO2(OH)2 (g).”
From Potassium, Chlorine, and Sulfur in Ash, Particles, Deposits, and Corrosion during Wood Combustion in a Circulating Fluidized-Bed Boiler (2007) · cites this paper as [11]
In the citing paper
“Judging from previous laboratory investigations in similar environments, the acceleration of corrosion is attributed to the reaction of KCl (formed in the flue gas) with the protective chromium-rich oxide, forming K2CrO4.”
From Potassium, Chlorine, and Sulfur in Ash, Particles, Deposits, and Corrosion during Wood Combustion in a Circulating Fluidized-Bed Boiler (2007) · cites this paper as [11]
1 more claim about this paper
Create a free account to see every claim other papers make about this one.
Citations
Cites
Thermochemical data of pure substances
(1993) · Choice Reviews Online · doi:10.5860/choice.31-0632 · Cited by 4,494
Thermochemical Data of Pure Substances
Barin, I. (1995) · doi:10.1002/9783527619825 · Cited by 4,241
The implications of chlorine-associated corrosion on the operation of biomass-fired boilers
Nielsen, H. P., Frandsen, F. J., Dam-Johansen, K., & Baxter, L. L. (2000) · Progress in Energy and Combustion Science · doi:10.1016/s0360-1285(00)00003-4 · Cited by 785
Grabke, H. J., Reese, E., & Spiegel, M. (1995) · Corrosion Science · doi:10.1016/0010-938x(95)00011-8 · Cited by 537
Asteman, H., Svensson, J.-E., Norell, M., & Johansson, L.-G. (2000) · Oxidation of Metals · doi:10.1023/a:1004642310974 · Cited by 325
Self-citationAsteman, H., Svensson, J.-E., Johansson, L.-G., & Norell, M. (1999) · Oxidation of Metals · doi:10.1023/a:1018875024306 · Cited by 304
Self-citationDeposition and high temperature corrosion in a 10 MW straw fired boiler
Michelsen, H. P., Frandsen, F., Dam-Johansen, K., & Larsen, O. H. (1998) · Fuel Processing Technology · doi:10.1016/s0378-3820(97)00062-3 · Cited by 258
Halvarsson, M., Tang, J. E., Asteman, H., Svensson, J.-E., & Johansson, L.-G. (2006) · Corrosion Science · doi:10.1016/j.corsci.2005.08.012 · Cited by 146
Self-citationZahs, A., Spiegel, M., & Grabke, H. (1999) · Materials and Corrosion · doi:10.1002/(sici)1521-4176(199910)50:10<561::aid-maco561>3.0.co;2-l · Cited by 131
Accelerated oxidation rate of chromium induced by sodium chloride
Shinata, Y. (1987) · Oxidation of Metals · doi:10.1007/bf00659274 · Cited by 129
Research works printed but not linked: 1
- Y. Shinata, 1987, Oxidation of Metals., 27, 315, 10.1007/bf00659274 · DOI · Paper page
Cited by
Items 101–183 of 183
Wu, D., Liu, S., Yuan, Z., Cao, P., Wei, X., & Zhang, C. (2021) · Journal of Thermal Spray Technology · doi:10.1007/s11666-021-01248-1 · Cited by 14
Wu, D., Dahl, K. V., Madsen, J. L., Christiansen, T. L., Montgomery, M., & Hald, J. K. (2018) · ACS Applied Energy Materials · doi:10.1021/acsaem.7b00253 · Cited by 14
Olivas-Ogaz, M. A., Eklund, J., Svensson, J.-E., Liske, J., & Jonsson, T. (2017) · Oxidation of Metals · doi:10.1007/s11085-017-9763-z · Cited by 13
Self-citationPorosity-Based Corrosion Model for Alkali Halide Ash Deposits during Biomass Co-firing
O’Hagan, C. P., O’Brien, B., Griffin, F., Hooper, B., Leen, S. B., & Monaghan, R. F. D. (2015) · Energy & Fuels · doi:10.1021/ef502275j · Cited by 14
A Comparative Study of the Initial Corrosion of KCl and PbCl2 on a Low-Alloyed Steel
Larsson, E., Gruber, H., Hellström, K., Jonsson, T., Liske, J., & Svensson, J. E. (2017) · Oxidation of Metals · doi:10.1007/s11085-017-9765-x · Cited by 14
Self-citationMeißner, T. M., Grégoire, B., Montero, X., Miller, E., Maier, J., & Galetz, M. C. (2020) · Energy & Fuels · doi:10.1021/acs.energyfuels.0c01474 · Cited by 15
Effect of microstructure on KCl corrosion attack of modified AISI 310 steel
Malede, Y. C., Montgomery, M., Dahl, K. V., & Hald, J. K. (2017) · Materials at High Temperatures · doi:10.1080/09603409.2017.1389381 · Cited by 14
“chloride followed by formation of oxide through active oxidation [3,15,25] and/or ionic transport [26,27] .”
BackgroundInfluence of PbCl2 and KCl salt mixture on high temperature corrosion of alloy 625
Núñez, A. M., Börjesson, E., Kinnunen, H., Lindberg, D., & Norling, R. (2023) · Fuel · doi:10.1016/j.fuel.2023.130196 · Cited by 12
Okoro, S. C., Montgomery, M., Frandsen, F., & Pantleon, K. (2017) · Oxidation of Metals · doi:10.1007/s11085-017-9794-5 · Cited by 14
Calmunger, M., Chai, G., Johansson, S., & Moverare, J. J. (2014) · Theoretical and Applied Mechanics Letters · doi:10.1063/2.1404104 · Cited by 12
The Influence of KCl and HCl on the High-Temperature Oxidation of a Fe-2.25Cr-1Mo Steel at 400 °C
Larsson, E., Liske, J., Persdotter, A., Jonsson, T., Svensson, J., & Johansson, L.-G. (2019) · Oxidation of Metals · doi:10.1007/s11085-019-09943-9 · Cited by 12
Self-citationCorrosion of Heat-Transfer Materials Induced by KCl, HCl, and O2 Under Chemical-Looping Conditions
Eriksson, J.-E., Lehmusto, J., Silvander, L., Lindberg, D. M., Zevenhoven, M., Yrjas, P., Brink, A., Hupa, M. M., & Hupa, L. (2024) · High Temperature Corrosion of Materials · doi:10.1007/s11085-024-10250-1 · Cited by 11
Mori, G., Vidic, K., Bucher, E., Yasir, M., Hornauer, D., Nachtnebel, M., Fitzek, H., & Schroettner, H. (2019) · Materials and Corrosion · doi:10.1002/maco.201810451 · Cited by 11
Should the oxygen source be considered in the initiation of KCl-induced high-temperature corrosion?
Lehmusto, J., Sattari, M., Halvarsson, M., & Hupa, L. (2021) · Corrosion Science · doi:10.1016/j.corsci.2021.109332 · Cited by 11
Ding, Y., Vandervort, J. A., Strand, C. L., & Hanson, R. K. (2021) · Journal of Quantitative Spectroscopy and Radiative Transfer · doi:10.1016/j.jqsrt.2021.107895 · Cited by 11
Sadeghi, E., Markocsan, N., Hussain, T., Huhtakangas, M., & Joshi, S. V. (2018) · CORROSION · doi:10.5006/2802 · Cited by 10
Lindmark, H., Phother-Simon, J., Paz, M. D., Nockert, J., Lind, F., Jonasson, A., Barisic, V. B., Vänskä, K., Rioja-Monllor, L., & Liske, J. (2023) · Fuel · doi:10.1016/j.fuel.2022.127299 · Cited by 10
Superheater Corrosion Produced by Biomass Fuels
Sharp, W. B., Singbeil, D., & Keiser, J. R. (2012) · NACE CORROSION Conference · doi:10.5006/c2012-01308 · Cited by 11
Controlling Atmospheric Corrosion of Weathering Steel Using Anodic Polarization Protection Technique
Abdo, H. S., Seikh, A. H., Fouly, A., & Hashmi, F. H. (2021) · Processes · doi:10.3390/pr9081469 · Cited by 10
Wu, D., Li, Y., Yuan, Z., Xiang, L., Wei, X., & Zhang, C. (2023) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2023.130117 · Cited by 11
High-Temperature Corrosion Characterization of Ni-Al Laser Cladding: The Effect of Al Content and Fe
Wang, X., Liu, Z., Cheng, K., Li, J., Ning, H., & Mao, J. (2024) · Journal of Thermal Spray Technology · doi:10.1007/s11666-024-01782-8 · Cited by 9
Investigating corrosion memory: The influence of previous boiler operation on current corrosion rate
Paz, M. D., Zhao, D., Karlsson, S., Liske, J., & Jonsson, T. (2016) · Fuel Processing Technology · doi:10.1016/j.fuproc.2016.09.018 · Cited by 9
Okoro, S. C., Montgomery, M., Frandsen, F., & Pantleon, K. (2017) · Surface and Coatings Technology · doi:10.1016/j.surfcoat.2017.03.068 · Cited by 9
KCl‐induced corrosion of Ni‐based alloys containing 35–45 wt% Cr
Malede, Y. C., Simon, J. P., Jonsson, T., Montgomery, M., Dahl, K. V., & Hald, J. (2019) · Materials and Corrosion · doi:10.1002/maco.201810658 · Cited by 8
Wu, H., Bankiewicz, D., Yrjas, P., & Hupa, M. M. (2015) · Energy & Fuels · doi:10.1021/acs.energyfuels.5b00204 · Cited by 9
Broström, M. (2010) · DiVA at Umeå University (Umeå University) · Cited by 21
Engineering polyaryl ether coatings bearing phthalazinone moiety resistant to salt spray corrosion
Zhao, Y., Liu, L., Li, J., Zhao, J., Gu, C., Liu, B., Wang, D., Zhang, S., Jian, X., & Weng, Z. (2024) · Applied Surface Science · doi:10.1016/j.apsusc.2024.162148 · Cited by 8
The analysis of furnace wall deposits in a low-NOx waste wood-fired bubbling fluidised bed boiler
Alipour, Y., Viklund, P., & Henderson, P. (2012) · KTH Publication Database DiVA (KTH Royal Institute of Technology) · Cited by 8
Laboratory studies on the ageing behaviour of waste incineration superheater ash deposits
Balint, R., Niemi, J., Hayashi, S., & Lehmusto, J. (2025) · Energy · doi:10.1016/j.energy.2025.135359 · Cited by 7
Calmunger, M., Chai, G., Johansson, S., & Moverare, J. J. (2013) · Key engineering materials · doi:10.4028/www.scientific.net/kem.592-593.590 · Cited by 7
Corrosion in Complex Environments
Young, D. J. (2016) · Elsevier eBooks · doi:10.1016/b978-0-08-100101-1.00012-1 · Cited by 7
Talus, A., Alipour, Y., Norling, R., & Henderson, P. (2016) · Materials and Corrosion · doi:10.1002/maco.201508693 · Cited by 7
Singh, M. K., Mahobia, G. S., Sinha, O. P., & Singh, V. (2019) · Materials Research Express · doi:10.1088/2053-1591/ab3547 · Cited by 6
The potential of SO2 for reducing corrosion in WtE plants
Hunsinger, H., & Andersson, S. (2014) · Journal of Material Cycles and Waste Management · doi:10.1007/s10163-014-0271-9 · Cited by 6
Kingsbery, P., & Stephan‐Scherb, C. (2022) · Materials and Corrosion · doi:10.1002/maco.202112901 · Cited by 6
Dominating High Temperature Corrosion Mechanisms in Low Alloy Steels in Wood Chips Fired Boilers
Gruber, T., Retschitzegger, S., Scharler, R., & Obernberger, I. (2016) · Energy & Fuels · doi:10.1021/acs.energyfuels.5b02290 · Cited by 6
Effect of service exposure on KCl corrosion attack of AISI 347H FG steel
Malede, Y. C., Dahl, K. V., Montgomery, M., Grumsen, F. B., & Hald, J. K. (2019) · Journal of Materials Science · doi:10.1007/s10853-019-03863-4 · Cited by 6
Wu, D., Wu, H., Yuan, Z., Zheng, J., Wei, X., & Zhang, C. (2022) · Journal of Thermal Spray Technology · doi:10.1007/s11666-022-01451-8 · Cited by 6
Ssenteza, V., Jonsson, T., Nockert, J., & Liske, J. (2024) · High Temperature Corrosion of Materials · doi:10.1007/s11085-024-10265-8 · Cited by 5
Ssenteza, V., Panas, I., Rioja-Monllor, L., Chyrkin, A., Sand, T., Siriki, R., & Jonsson, T. (2025) · Materials & Design · doi:10.1016/j.matdes.2025.113894 · Cited by 6
Verma, R., & Kaushal, G. (2022) · Journal of Thermal Spray Technology · doi:10.1007/s11666-022-01445-6 · Cited by 6
“Pettersson et al. 2005 (Ref 40), Jonsson et al. 2009 (Ref 41), Pettersson et al. 2009 (Ref 42) and Karlsson et al. 2012 (Ref 43) observed similar chromate production on 304 stainless steel at 600 C in the presence of KCl and reported that the chromate synthesis acted as a sink for chromium in the…”
BackgroundImproving Heat Recovery In Biomass-Fired Boilers
Keiser, J. R., USDOE Office of Energy Efficiency and Renewable Energy (EERE), Sharp, W., Singbeil, D., Singh, P., Frederick, L. A., & Meyer, J. (2013) · OSTI OAI (U.S. Department of Energy Office of Scientific and Technical Information) · doi:10.2172/1093743 · Cited by 7
Yildiz, C., Richter, M., Ströhle, J., & Epple, B. (2024) · Energy & Fuels · doi:10.1021/acs.energyfuels.3c04150 · Cited by 4
On High-Temperature Behaviours of Heat Resistant Austenitic Alloys
Calmunger, M. (2015) · Linköping University Electronic Press eBooks · doi:10.3384/diss.diva-122945 · Cited by 4
“The materials used for future biomass-fired power plants with higher efficiency are required to display improved properties as higher yield strength, fatigue strength, creep strength and high-temperature corrosion resistance [9–13].”
Gada, H., Mudgal, D., & Ahmad, B. (2019) · Journal of Physics Conference Series · doi:10.1088/1742-6596/1240/1/012129 · Cited by 4
High Temperature Corrosion under Simulated Biomass Deposit Conditions
Pettersson, R. F. A., Flyg, J., & Viklund, P. (2009) · NACE CORROSION Conference · doi:10.5006/c2009-09168 · Cited by 4
Electrochemical Corrosion Investigations on Anaerobic Treated Distillery Effluent
Ram, C., Sharma, C., & Singh, A. K. (2014) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-014-0960-5 · Cited by 4
Lehmusto, J., Bergelin, M., Lindberg, D., & Juhanoja, J. (2018) · CORROSION · doi:10.5006/2859 · Cited by 4
Chen, T., Liang, Y., Hua, C., Cao, W., Su, C., Yang, Y., Yang, Z., Huang, T., Liu, G., & Song, P. Y. (2026) · Journal of Alloys and Compounds · doi:10.1016/j.jallcom.2026.188311 · Cited by 3
Nikbakht, A., Bahramian, B., & Geers, C. (2024) · High Temperature Corrosion of Materials · doi:10.1007/s11085-024-10259-6 · Cited by 4
Danish Experiences in Biomass Corrosion and Recent Areas of Research
Montgomery, M., Malede, Y. C., Wu, D., & Dahl, K. V. (2018) · CORROSION · doi:10.5006/2963 · Cited by 3
“The coupled effect of 40% H2O + 5% O2 in the gas phase and small amounts of KCl deposit on stainless alloys at 600°C was investigated by [10,11] focusing on the mechanism of breakdown of the protective oxide by potassium to form potassium chromate.”
BackgroundCalmunger, M., Chai, G., Johansson, S., & Moverare, J. J. (2013) · Cited by 3
Influence of Deformation Rate on Mechanical Response of an AISI 316L Austenitic Stainless Steel
Calmunger, M., Chai, G., Johansson, S., & Moverare, J. J. (2014) · Advanced materials research · doi:10.4028/www.scientific.net/amr.922.49 · Cited by 3
High-Temperature Behaviour of Austenitic Alloys
Calmunger, M. (2013) · Linköping University Electronic Press eBooks · doi:10.3384/lic.diva-98242 · Cited by 3
“It is a sustainable fuel because it gives no net contribution of CO2 to the atmosphere and it can be considered endless [3, 4].”
Furnace Wall Corrosion in a Wood-fired Boiler
Alipour, Y. (2015) · DiVA (Digitala Vetenskapliga Arkivet) · Cited by 5
Gall, D., Allgurén, T., Johansson, J., Normann, F., Hultén, A. H., Gunnarsson, A., & Andersson, K. (2022) · Energy & Fuels · doi:10.1021/acs.energyfuels.2c00293 · Cited by 2
EFFECT OF BURNING BIO-MASS FUEL ON THE CORROSION PERFORMANCE OF STEELS IN THE 34.5MW BOILER
Bhagria, B. K., Sidhu, S. S., Ahuja, L., & Mudgal, D. (2023) · Surface Review and Letters · doi:10.1142/s0218625x24500045 · Cited by 3
High‐temperature KCl‐induced corrosion of high Cr and Ni alloys investigated by in‐situ diffraction
Kingsbery, P., Manzoni, A. M., Ocaño, P. S., Többens, D. M., & Stephan‐Scherb, C. (2024) · Materials and Corrosion · doi:10.1002/maco.202314224 · Cited by 2
Mechanical Behaviors of Alloy 617 with Varied Strain Rates at High Temperatures
Calmunger, M., Chai, G., Johansson, S., & Moverare, J. J. (2014) · Materials science forum · doi:10.4028/www.scientific.net/msf.783-786.1182 · Cited by 2
Corrosion Behaviour of Hastelloy C22 in Alkali Salt Environment
Kassim, S. A., Yeian, L. S., & Abdullah, T. K. (2018) · Journal of Physics Conference Series · doi:10.1088/1742-6596/1082/1/012107 · Cited by 2
Reducing High Temperature Corrosion when Burning Waste by Adding Digested Sewage Sludge
Karlsson, S., Åmand, L.-E., & Pettersson, J. (2011) · Chalmers Publication Library (Chalmers University of Technology) · Cited by 6
Self-citationSsenteza, V., Olausson, M. D. P., Eklund, J., Nockert, J., Liske, J., & Jonsson, T. (2025) · Energy & Fuels · doi:10.1021/acs.energyfuels.4c04806 · Cited by 1
Persdotter, A., Larsson, H., Eklund, J., Bigdeli, S., & Jonsson, T. (2024) · Corrosion Science · doi:10.1016/j.corsci.2024.112473 · Cited by 1
Khantisopon, K., Singh, S., Joshi, V. V., Jitputti, J., Berndt, C. C., & Ang, A. S. M. (2025) · Journal of Thermal Spray Technology · doi:10.1007/s11666-025-02041-0 · Cited by 1
Corrosion behavior of Ni and Ni-Cr-Mo alloys in high-temperature KCl-MgCl2 salt vapor
Chen, J., Liu, D., Chen, H. L., Wu, C., Ren, K., Li, Y., Wang, J., (107450), C. W., & Li, Y. (2026) · Materials Chemistry and Physics · doi:10.1016/j.matchemphys.2026.132340 · Cited by 1
Yao, X., Zhao, Z., Li, L., Xu, K., Zhang, X., & Xu, K. (2026) · Journal of the Energy Institute · doi:10.1016/j.joei.2026.102727 · Cited by 1
NaCl- and CaCl2-Induced High Temperature Corrosion of Automotive Exhaust Components
Vidic, K., Mori, G., Yasir, M., & Knoll, D. (2018) · NACE CORROSION Conference · doi:10.5006/c2018-11303 · Cited by 1
An in plant study of High Temperature Corrosion during Co-combustion of Biomass and Coal
Sundqvist, S. (2012) · Chalmers Publication Library (Chalmers University of Technology)
High Temperature Corrosion of Stainless Steels - The Effects of Chloride Salts and SO2(g)
Karlsson, S. (2011) · Chalmers Publication Library (Chalmers University of Technology) · Cited by 1
Long Term High-Temperature Environmental Effect on Impact Toughness in Austenitic Alloys
Calmunger, M., Chai, G., Johansson, S., & Moverare, J. J. (2014) · Key engineering materials · doi:10.4028/www.scientific.net/kem.627.205
Experimental and numerical characterisation of materials for biomass co-firing
O’Hagan, C. P. (2017) · Arrow@dit (Dublin Institute of Technology) · doi:10.13025/16702 · Cited by 1
Hooshyar, H., Sattari, M., Jonsson, T., Johansson, L., Svensson, J., & Liske, J. (2023) · SSRN Electronic Journal · doi:10.2139/ssrn.4514530
Self-citationHuang, W., Song, P., Huang, T., Wang, J., Zhou, R., & Lu, J. (2024) · SSRN Electronic Journal · doi:10.2139/ssrn.4864963
Talus, A., Norling, R., & Núñez, A. M. (2024) · IEEE Lasers and Electro-Optics Society Annual Meeting (LEOS) · doi:10.5006/c2024-21033
Niemi, J., Balint, R., & Lehmusto, J. (2025) · Chemical Engineering Science · doi:10.1016/j.ces.2025.121726
Eriksson, J.-E., Mori, S., Silvander, L., Hupa, L., & Lehmusto, J. (2025) · High Temperature Corrosion of Materials · doi:10.1007/s11085-025-10339-1
Dureuil, I., Lalau, Y., Martinent, J.-R., Dejean, G., Meffre, A., Lemrabti, I., Coquelet, C., & Minh, D. P. (2026) · ChemEngineering · doi:10.3390/chemengineering10110134
Szajna, E., TUPAJ, M., Tomaszewska, A., Dudek, A., Moskal, G., Jagiełło, K., Hercog, J., Szymański, K., Trzcionka-Szajna, A., & Purzyńska, H. (2025) · Journal of Thermal Analysis and Calorimetry · doi:10.1007/s10973-025-14908-z
Materials and Coatings for Superheater Tubes in Biomass- and Waste-fired Boilers
Ssenteza, V. (2023) · Chalmers Research (Chalmers University of Technology)
High-temperature corrosion behavior of Ni-Cr-Mo-xSi alloy cladding layer in molten NaCl-KCl
Kong, Y., Cheng, K., Shen, Y., Ning, H., Li, J., Huang, Y., Liu, Q., & Liu, Z. (2025) · Journal of Energy Storage · doi:10.1016/j.est.2025.118553
A Study on the Degradation Mechanisms of Heat-Resistant Grate Bars Induced by High-Alkali Deposits
Moosavi, P., Hasani, S., Mohebbi, E., Ebrahimi, M., Mashreghi, A., Shadkami, M. D., Zadmehr, M. R., & Rajabi, A. (2026) · Journal of Failure Analysis and Prevention · doi:10.1007/s11668-026-02409-6
“The degradation of components and the accumulation of alkalis are significant concerns that extend beyond iron ore pelletizing facilities, as demonstrated by extensive analyses conducted across various industries [13, 14, 44, 45, 51, 52, 55, 63, 73, 75–79].”
Svaveldosering i fastbränslepanna
Gunnarsson, A. (2026) · Lund University Publications Student Papers (Lund University)
Metadata
- Authors
- Pettersson, J., Asteman, H., Svensson, J. E., & Johansson, L. G.
- Affiliations
- Chalmers University of Technology (SE)
- Max-Planck-Institut für Nachhaltige Materialien (DE)
- Corresponding author
- Johansson, L. -G.
- Venue
- Oxidation of Metals
- Published
- 2005-08
- Volume
- 64
- Issue
- 1-2
- Pages
- 23-41
- ISSN
- 0030-770X (ISSN-L)
- 1573-4889
- OpenAlex
- W2042098561
- Cited by
- 182
- References
- 21
- Citations by year
- 2026: 5 · 2025: 8 · 2024: 13 · 2023: 10 · 2022: 9 · 2021: 10 · 2020: 9 · 2019: 17 · 2018: 10 · 2017: 12 · 2016: 9 · 2015: 13 · 2014: 15 · 2013: 10 · 2012: 10
- FWCI
- 4.63
- Type
- journal article
- Language
- en
- Open access
- closed
- Licence
- www.springer.com/tdm (tdm)
- Locations
- Oxidation of Metals (publishedVersion)
- Chalmers Publication Library (Chalmers University of Technology) (submittedVersion)
- Chalmers Research (Chalmers University of Technology) (submittedVersion)
- Funders
- Chalmers Tekniska Högskola
- Topics
- Physical Sciences › Materials Science › Surfaces, Coatings and Films › High-Temperature Coating Behaviors
- Physical Sciences › Materials Science › Metals and Alloys › Hydrogen embrittlement and corrosion behaviors in metals
- Physical Sciences › Materials Science › Materials Chemistry › Corrosion Behavior and Inhibition
- Keywords
- high-temperature corrosion, 304 stainless steel, potassium chloride, potassium, potassium chromate, chromium depletion, spinel oxides, oxide scale growth, scale/metal interface
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.