Lignin-impregnated biochar assisted with microwave irradiation for CO2 capture: adsorption performance and mechanism
Open accessThe DOI matches its Crossref record; 63 of the 63 references it cites were found in a registry or an index; 2 of the 57 sources its claims cite were checked for support.
Abstract
Abstract Bamboo biochar was modified by lignin impregnation and microwave irradiation to enhance its performance for CO 2 capture. The pore structure of lignin-impregnated biochar was significantly affected by the impregnation ratio. The maximum specific surface area of 377.32 m 2 g −1 and micropore volume of 0.163 cm 3 g −1 were observed on the biochar with an impregnation ratio of 1:20 (mass ratio of lignin to biochar). Lignin impregnation increased the CO 2 adsorption capacity of biochar up to 134.46 mg g −1 . Correlation analysis confirmed the crucial role of biochar’s pore structure in adsorption. The Avrami model fitted the CO 2 capture curves well. The calculation of adsorption activation energy suggested that the adsorption process was dominated by physical mechanism assisted with partial chemical mechanism. Meanwhile, Langmuir isotherm analysis indicated that lignin impregnation transformed the larger pores of biochar into more uniform micropores, thereby making the adsorption process closer to monolayer adsorption. Both the high reusability (89.79–99.06%) after 10 successive cycles and the excellent CO 2 selectivity in competitive adsorption confirmed that lignin-impregnated biochar is an outstanding adsorbent for CO 2 capture. Graphical Abstract
Overview
CoChat Summary
TL;DR
This study modified bamboo biochar by lignin impregnation plus microwave irradiation to improve CO2 capture, and found that pore structure and basicity jointly controlled performance. The best sample reached 134.46 mg g−1 CO2 uptake at 0°C, showed 89.79–99.06% reuse efficiency after 10 cycles, and had strong CO2 selectivity in competitive gas tests.
Key findings
- Lignin impregnation plus microwave irradiation increased biochar specific surface area up to 377.32 m² g−1 and micropore volume up to 0.163 cm³ g−1 at the 1:20 lignin-to-biochar mass ratio.
- CO2 adsorption capacity reached 134.46 mg g−1; across samples it was 105.85–134.46 mg g−1 at 0°C.
- Linear correlation analysis showed pore structure was dominant for CO2 capture, with R² = 0.9427 for SSA, 0.8343 for pore volume, and 0.9204 for micropore volume; micropores mattered more than total pore volume.
- Kinetic and thermodynamic analyses indicated adsorption was mainly physisorption with slight chemisorption; Avrami model fit best with R² = 0.968–0.984, and activation energy ranged from 1.23 to 5.05 kJ mol−1.
- Reusability remained high after 10 adsorption/desorption cycles, with reuse efficiency of 89.79–99.06%; in competitive adsorption, single-gas uptake dropped to 23.70 mg g−1 CO2, 0.14 mg g−1 NO, and 45.06 mg g−1 SO2 from 28.50, 0.24, and 50.10 mg g−1, respectively.
Methods
- Bamboo was pyrolyzed at 600°C for 5 h to make biochar, then modified by wet lignin impregnation at lignin:biochar mass ratios of 1:3, 1:5, 1:10, 1:15, and 1:20, followed by microwave irradiation at 600 W for 20 min.
- Characterization included N2 adsorption/desorption, elemental analysis, TGA, Raman spectroscopy, Boehm titration, and FTIR.
- CO2 adsorption was measured by TGA at 25, 35, 45, 55, and 65°C and at 0°C for isotherms; reusability used 10 consecutive cycles, and selectivity was tested in multicomponent breakthrough with CO2/NO/SO2 at 12/0.4/0.4 vol%.
Limitations
- The paper states that datasets are available from the corresponding author on reasonable request, which means the data are not fully deposited in the paper itself.
- The study itself uses only one biomass source and precursor system (bamboo biochar with lignin), so generalization to other feedstocks is not directly tested in the text.
- The paper reports multicomponent selectivity using CO2, NO, and SO2 at one gas-mixture condition; broader real-flue-gas variability is not examined in the text.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
2 Valid · 3 Not valid · 40 Not checked · 100 Own results and interpretations
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“Lignin impregnation increased the CO 2 adsorption capacity ofbiochar upto134.46mg g -1 .”
states a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The Avrami model fitted the CO 2 capture curveswell.”
boostedstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“CO2 uptake onlignin-impregnated biochar reached 134.46 mg g -1”
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper states — it cites no source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“CO2 uptake onlignin-impregnated biochar reached 134.46 mg g -1 andwasassociated withmicropore, alkalinity, andtemperature.”
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
A result the paper reports from its own data — it cites no other source for it, so there is none to check. The quote shows it is in the paper.
In the paper
“The maximum specific surface area of377.32 m 2 g -1 andmicropore volume of0.163 cm 3 g -1 were observed onthebiochar withanimpregnation ratio of1:20 (mass ratio oflignin tobiochar).”
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
74 more claims
Create a free account to see all 145 claims and every source verdict.
- Probably not a substantial claim. 21
- Borderline: one of the tests for a substantial claim is unclear. 2
- It may state two separate claims as one. 52
- The quote only partly states this claim. 1
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Self-check results appear here once an independent check has confirmed them.
Cited works that were retracted
Works this paper cites that were later retracted, from the retraction notices publishers deposit. Major when the notice came out before this paper was published.
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
“Igalavithana et al. (2020a) found that KOH-activated biochar showed excellent CO 2 adsorption capacity due to its abundant micropo-res developed after activation.”
Cited work 10.1016/j.scitotenv.2020.139845 · retracted 2020-10-15 · notice 10.1016/j.scitotenv.2020.139845 · this paper published 2024-03-08
Citations
Cites
1 retracted
Igalavithana, A. D., Choi, S. W., Shang, J., Hanif, A., Dissanayake, P. D., Tsang, D. C. W., Kwon, J.-H., Lee, K. B., & Ok, Y. S. (2020) · Science of The Total Environment · doi:10.1016/j.scitotenv.2020.139845 · Cited by 180 · cited 2×
“Igalavithana et al. (2020a) found that KOH-activated biochar showed excellent CO 2 adsorption capacity due to its abundant micropo-res developed after activation.”
RetractedAdsorption of VOCs onto engineered carbon materials: A review
Zhang, X., Gao, B., Creamer, A. E., Cao, C., & Li, Y. (2017) · Journal of Hazardous Materials · doi:10.1016/j.jhazmat.2017.05.013 · Cited by 1,479 · cited 1×
“That was because lignin impregnation reduced biochar’s pore size and increased the diffusion resistance of CO 2 in the narrow pores (Zhang et al. 2017).”
Self-citationLignin utilization: A review of lignin depolymerization from various aspects
Chio, C., Sain, M., & Qin, W. (2019) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2019.03.008 · Cited by 1,209 · cited 1×
“This results in low lignin utilization efficiency and even causes serious environmental pollution (Chio et al. 2019).”
Foong, S. Y., Liew, R. K., Yang, Y., Cheng, Y. W., Yek, P. N. Y., Wan Mahari, W. A., Lee, X. Y., Han, C. S., Vo, D.-V. N., Van Le, Q., et al. (2020) · Chemical Engineering Journal · doi:10.1016/j.cej.2020.124401 · Cited by 749 · cited 1×
“It transfers electromagnetic energy into heat energy and accumulate it inside the material via frequency oscillation of alternating electric field, making polar molecule rub against each other to generate heat (Foong et al. 2020).”
Zhang, J., Liu, J., & Liu, R. (2015) · Bioresource Technology · doi:10.1016/j.biortech.2014.11.011 · Cited by 560 · cited 1×
“This can be ascribed to the volatilization of organic sulfur content (Zhang et al. 2015), and some of the hydrogen bonds were broken during the dehydration process during microwave irradiation (Devi and Saroha 2015a).”
Hong, W. Y. (2022) · Carbon Capture Science & Technology · doi:10.1016/j.ccst.2022.100044 · Cited by 455 · cited 1×
“Adsorption is one of the most promising strategies in CO 2 capture for its superiorities of high efficiency, cost-effectiveness, stability, and easy operation (Hong 2022).”
Biochar from microwave pyrolysis of biomass: A review
Li, J., Dai, J., Liu, G., Zhang, H., Gao, Z., Fu, J., He, Y., & Huang, Y. (2016) · Biomass and Bioenergy · doi:10.1016/j.biombioe.2016.09.010 · Cited by 442
Carbon dioxide capture using biochar produced from sugarcane bagasse and hickory wood
Creamer, A. E., Gao, B., & Zhang, M. (2014) · Chemical Engineering Journal · doi:10.1016/j.cej.2014.03.105 · Cited by 432 · cited 1×
“According to gravimetric method reported previously (Creamer et al. 2014), CO 2 capture experiment was carried out on the TGA.”
Self-citationAn overview of activated carbons utilization for the post-combustion carbon dioxide capture
Rashidi, N. A., & Yusup, S. (2016) · Journal of CO2 Utilization · doi:10.1016/j.jcou.2015.11.002 · Cited by 394 · cited 1×
“…microporosity and alkalinity of biochar, such as CO 2 activation (Dissanayake et al. 2020), ultrasonic treatment (Shafawi et al. 2021), impregnation (Zhang et al. 2022b), grafting (Zhang et al. 2022a), solid–solid mixing (Rashidi and Yusup 2016), ligand functionalization (Mankar et al. 2021), etc.”
Petrovic, B., Gorbounov, M., & Masoudi Soltani, S. (2021) · Microporous and Mesoporous Materials · doi:10.1016/j.micromeso.2020.110751 · Cited by 381 · cited 1×
“Nevertheless, in terms of CO 2 adsorption, micropores and alkalinity play more crucial role (Goel et al. 2021; Petrovic et al. 2021).”
Influence of activation conditions on the physicochemical properties of activated biochar: a review
Panwar, N. L., & Pawar, A. (2022) · Biomass Conversion and Biorefinery · doi:10.1007/s13399-020-00870-3 · Cited by 369 · cited 1×
“Impregnation is a mild and economical modification process, by contrast, other methods like KOH activation and steam activation are usually carried out under strict conditions requiring high temperature and high pressure (Panwar and Pawar 2022).”
A review on microwave assisted pyrolysis of coal and biomass for fuel production
Mushtaq, F., Mat, R., & Ani, F. N. (2014) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2014.07.073 · Cited by 351 · cited 1×
“Many studies have proven that biochar has higher loss tangent value than raw biomass (Mushtaq et al. 2014; Salema et al. 2017; Siddique et al. 2022).”
Kostas, E. T., Beneroso, D., & Robinson, J. P. (2017) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2017.03.135 · Cited by 319 · cited 1×
“Biomass usually has poor microwave absorption capacity because of its low loss tangent value (Kostas et al. 2017; Salema et al. 2017).”
Adsorption of CO2 from flue gas by novel seaweed-based KOH-activated porous biochars
Ding, S., & Liu, Y. (2020) · Fuel · doi:10.1016/j.fuel.2019.116382 · Cited by 311 · cited 1×
“Pseudo-first-order model is mainly used to describe pure physical adsorption (Ding and Liu 2020), while pseudo-second-order model is applicable when the chemisorption is the rate-limiting step (Cho et al. 2017).”
Functionalized MOFs for Enhanced CO2 Capture
Torrisi, A., Bell, R. G., & Mellot-Draznieks, C. (2010) · Crystal Growth & Design · doi:10.1021/cg100646e · Cited by 293 · cited 1×
“Adsorption capacity of biochar is affected by many factors, such as porosity (Guo et al. 2022), alkalinity (Kumar et al. 2015), surface functional groups (Torrisi et al. 2010), mineral content (Li et al. 2017), hydro-philicity and hydrophobicity (Dissanayake et al. 2020).”
Strategic use of biochar for CO2 capture and sequestration
Jung, S., Park, Y.-K., & Kwon, E. E. (2019) · Journal of CO2 Utilization · doi:10.1016/j.jcou.2019.04.012 · Cited by 268 · cited 1×
“For example, metal and metal oxide impregnation improves the basicity of biochar (Jung et al. 2019; Zubbri et al. 2020), while glucose and chitosan impregnation strengthens the pore structure of biochar (Zhang et al. 2022b).”
Microwave and slow pyrolysis biochar—Comparison of physical and functional properties
Mašek, O., Budarin, V., Gronnow, M., Crombie, K., Brownsort, P., Fitzpatrick, E., & Hurst, P. (2013) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2012.11.015 · Cited by 256 · cited 1×
“Similar observations have been reported by Mašek et al. (2013).”
Karimi, M., Shirzad, M., Silva, J. A. C., & Rodrigues, A. E. (2022) · Journal of CO2 Utilization · doi:10.1016/j.jcou.2022.101890 · Cited by 237
Gasification biochar from biowaste (food waste and wood waste) for effective CO2 adsorption
Igalavithana, A. D., Choi, S. W., Dissanayake, P. D., Shang, J., Wang, C.-H., Yang, X., Kim, S., Tsang, D. C. W., Lee, K. B., & Ok, Y. S. (2020) · Journal of Hazardous Materials · doi:10.1016/j.jhazmat.2019.121147 · Cited by 225 · cited 2×
“Igalavithana et al. (2020a) found that KOH-activated biochar showed excellent CO 2 adsorption capacity due to its abundant micropo-res developed after activation.”
Dissanayake, P. D., Choi, S. W., Igalavithana, A. D., Yang, X., Tsang, D. C. W., Wang, C.-H., Kua, H. W., Lee, K. B., & Ok, Y. S. (2020) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2020.109785 · Cited by 219 · cited 3×
“Adsorption capacity of biochar is affected by many factors, such as porosity (Guo et al. 2022), alkalinity (Kumar et al. 2015), surface functional groups (Torrisi et al. 2010), mineral content (Li et al. 2017), hydro-philicity and hydrophobicity (Dissanayake et al. 2020).”
Microwave pyrolysis of rice straw to produce biochar as an adsorbent for CO2 capture
Huang, Y.-F., Chiueh, P.-T., Shih, C.-H., Lo, S.-L., Sun, L., Zhong, Y., & Qiu, C. (2015) · Energy · doi:10.1016/j.energy.2015.02.026 · Cited by 211
Raganati, F., Alfe, M., Gargiulo, V., Chirone, R., & Ammendola, P. (2019) · Chemical Engineering Journal · doi:10.1016/j.cej.2019.04.165 · Cited by 209 · cited 4×
“This might be attributed to the deviations in the uniformity of adsorption sites, and different regions had different probabilities to capture CO 2 (Raganati et al. 2019).”
InfluentialCO2 capture by adsorption on biomass-derived activated char: A review.
Goel, C., Mohan, S., & Dinesha, P. (2021) · Science of the Total Environment · doi:10.1016/j.scitotenv.2021.149296 · Cited by 206 · cited 1×
“Nevertheless, in terms of CO 2 adsorption, micropores and alkalinity play more crucial role (Goel et al. 2021; Petrovic et al. 2021).”
Straw and wood based biochar for CO2 capture: Adsorption performance and governing mechanisms
Cao, L., Zhang, X., Xu, Y., Xiang, W., Wang, R., Ding, F., Hong, P., & Gao, B. (2022) · Separation and Purification Technology · doi:10.1016/j.seppur.2022.120592 · Cited by 196 · cited 3×
“Cao et al. (2022) prepared various straw and wood biochars, and found that the biochar with the highest alkalinity had the highest CO 2 uptake of 79.99 mg g − 1 at 0 °C.”
InfluentialSelf-citationTechnical challenges in scaling up the microwave technology for biomass processing
Siddique, I. J., Salema, A. A., Antunes, E., & Vinu, R. (2022) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2021.111767 · Cited by 189 · cited 1×
“Many studies have proven that biochar has higher loss tangent value than raw biomass (Mushtaq et al. 2014; Salema et al. 2017; Siddique et al. 2022).”
Shafawi, A. N., Mohamed, A. R., Lahijani, P., & Mohammadi, M. (2021) · Journal of Environmental Chemical Engineering · doi:10.1016/j.jece.2021.106869 · Cited by 187 · cited 1×
“…have been developed to improve the microporosity and alkalinity of biochar, such as CO 2 activation (Dissanayake et al. 2020), ultrasonic treatment (Shafawi et al. 2021), impregnation (Zhang et al. 2022b), grafting (Zhang et al. 2022a), solid–solid mixing (Rashidi and Yusup 2016), ligand…”
Devi, P., & Saroha, A. K. (2015) · Bioresource Technology · doi:10.1016/j.biortech.2015.05.084 · Cited by 186 · cited 2×
“As reported, the physical adsorption activation energy is less than 4.184 kJ mol − 1 , while it ranges 40–800 kJ mol − 1 for pure chemical adsorption (Devi and Saroha 2015b; Huang et al. 2015).”
InfluentialDevi, P., & Saroha, A. K. (2015) · Chemical Engineering Journal · doi:10.1016/j.cej.2015.02.087 · Cited by 168 · cited 2×
“As reported, the physical adsorption activation energy is less than 4.184 kJ mol − 1 , while it ranges 40–800 kJ mol − 1 for pure chemical adsorption (Devi and Saroha 2015b; Huang et al. 2015).”
InfluentialProcess and engineering trends in membrane based carbon capture
Sreedhar, I., Vaidhiswaran, R., Kamani, B. M., & Venugopal, A. (2017) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2016.10.025 · Cited by 167 · cited 1×
“Various methods, such as adsorption, absorption, chemical looping combustion, cryogenic distillation, and membrane separations have been employed for CO 2 capture (Sreedhar et al. 2017).”
Zhang, X., Miao, X., Xiang, W., Zhang, J., Cao, C., Wang, H., Hu, X., & Gao, B. (2021) · Journal of Hazardous Materials · doi:10.1016/j.jhazmat.2020.123540 · Cited by 150 · cited 1×
“Many adsor-bents, such as activated carbon (Zhang et al. 2021), carbon nano-tubes (Baghery et al. 2019), MOFs (Ma et al. 2022), zeolitic imidazolate frameworks (ZIFs) (Chang et al. 2020) and metal oxides (Liao et al. 2022) have already been employed for CO 2 adsorption.”
Self-citationLi, J., Liang, N., Jin, X., Zhou, D., Li, H., Wu, M., & Pan, B. (2016) · Chemosphere · doi:10.1016/j.chemosphere.2016.12.041 · Cited by 137 · cited 2×
“Therefore, biochar prepared by microwave irradiation has demonstrated more uniform micropores, superior specific surface area (SSA) and surface functional groups (Li et al. 2016; Shirvani-moghaddam et al. 2022).”
Kumar, K. V., Preuss, K., Lu, L., Guo, Z. X., & Titirici, M. M. (2015) · The Journal of Physical Chemistry C · doi:10.1021/acs.jpcc.5b06017 · Cited by 135
Methodological limitations to determining acidic groups at biochar surfaces via the Boehm titration
Tsechansky, L., & Gräber, E. R. (2013) · Carbon · doi:10.1016/j.carbon.2013.09.044 · Cited by 134 · cited 1×
“Boehm titration method was employed to determine the total basicity (Tsechansky and Graber 2014).”
Cho, D.-W., Kwon, G., Yoon, K., Tsang, Y. F., Ok, Y. S., Kwon, E. E., & Song, H. (2017) · Energy Conversion and Management · doi:10.1016/j.enconman.2017.04.095 · Cited by 115 · cited 1×
“Pseudo-first-order model is mainly used to describe pure physical adsorption (Ding and Liu 2020), while pseudo-second-order model is applicable when the chemisorption is the rate-limiting step (Cho et al. 2017).”
Atinafu, D. G., Yeol Yun, B., Uk Kim, Y., Wi, S., & Kim, S. (2021) · Chemical Engineering Journal · doi:10.1016/j.cej.2021.128887 · Cited by 114 · cited 1×
“Excessive microwave irradiation may also have side effects on biochar, such as the collapse of pore tunnel at high temperature (Atinafu et al. 2021).”
Chang, C.-W., Kao, Y.-H., Shen, P.-H., Kang, P.-C., & Wang, C.-Y. (2020) · Journal of Hazardous Materials · doi:10.1016/j.jhazmat.2020.122974 · Cited by 113 · cited 1×
“Many adsor-bents, such as activated carbon (Zhang et al. 2021), carbon nano-tubes (Baghery et al. 2019), MOFs (Ma et al. 2022), zeolitic imidazolate frameworks (ZIFs) (Chang et al. 2020) and metal oxides (Liao et al. 2022) have already been employed for CO 2 adsorption.”
Xiang, W., Zhang, X., Luo, J., Li, Y., Guo, T., & Gao, B. (2022) · Environmental Research · doi:10.1016/j.envres.2022.114339 · Cited by 111
Self-citationLi, G., Shen, B., Li, Y., Zhao, B., Wang, F., He, C., Wang, Y., & Zhang, M. (2015) · Journal of Hazardous Materials · doi:10.1016/j.jhazmat.2015.05.031 · Cited by 110 · cited 1×
“Arrhenius equation was used to calculate the activation energy of CO 2 adsorbed on biochar (Li et al. 2015; Raganati et al. 2019), which ranged from 1.23 kJ mol − 1 to 5.05 kJ mol − 1 (Fig.”
InfluentialZhang, X., Cao, L., Xiang, W., Xu, Y., & Gao, B. (2022) · Separation and Purification Technology · doi:10.1016/j.seppur.2022.121295 · Cited by 110
Self-citationPreparation of biochar with high absorbability and its nutrient adsorption–desorption behaviour
Gong, H., Tan, Z., Zhang, L., & Huang, Q. (2019) · Science of The Total Environment · doi:10.1016/j.scitotenv.2019.133728 · Cited by 109
Cao, W., Xu, H., Zhang, X., Xiang, W., Qi, G., Wan, L., & Gao, B. (2023) · Chemical Engineering Journal · doi:10.1016/j.cej.2023.144523 · Cited by 109
Self-citationLin, J., Sun, S., Xu, D., Cui, C., Ma, R., Luo, J., Fang, L., & Li, H. (2021) · Chemical Engineering Journal · doi:10.1016/j.cej.2021.132195 · Cited by 108 · cited 1×
“Bio-char with plentiful pores can absorb an abundance of microwave and converted it into heat energy (Lin et al. 2022).”
Sun, Y., Wang, T., Sun, X., Bai, L., Han, C., & Zhang, P. (2021) · Industrial Crops and Products · doi:10.1016/j.indcrop.2021.113473 · Cited by 97 · cited 1×
“Only large pores of biochar would be filled with lignin because it has high molecular weight and large molecular size (Sun et al. 2021).”
Enhancement of CO2 adsorption on biochar sorbent modified by metal incorporation
Zubbri, N. A., Mohamed, A. R., Kamiuchi, N., & Mohammadi, M. (2020) · Environmental Science and Pollution Research · doi:10.1007/s11356-020-07734-3 · Cited by 92 · cited 2×
“For example, metal and metal oxide impregnation improves the basicity of biochar (Jung et al. 2019; Zubbri et al. 2020), while glucose and chitosan impregnation strengthens the pore structure of biochar (Zhang et al. 2022b).”
Liao, W., Tang, C., Zheng, H., Ding, J., Zhang, K., Wang, H., Lu, J.-Q., Huang, W., & Zhang, Z. (2022) · Journal of Catalysis · doi:10.1016/j.jcat.2022.01.037 · Cited by 92
Salema, A. A., Ani, F. N., Mouris, J., & Hutcheon, R. (2017) · Fuel Processing Technology · doi:10.1016/j.fuproc.2017.06.006 · Cited by 91
Functional Biochar Synergistic Solid/Liquid-Phase CO2 Capture: A Review
Zhang, Y., Wang, S., Feng, D., Gao, J., Dong, L., Zhao, Y., Sun, S., Huang, Y., & Qin, Y. (2022) · Energy & Fuels · doi:10.1021/acs.energyfuels.1c04372 · Cited by 91
Chu, G., Zhao, J., Chen, F., Dong, X., Zhou, D., Liang, N., Wu, M., Pan, B., & Steinberg, C. E. W. (2017) · Environmental Pollution · doi:10.1016/j.envpol.2017.04.067 · Cited by 90 · cited 1×
“Chu et al. (2017) found biochar prepared by microwave irradiation had better pore structure compared with that prepared by muffle furnace.”
Zhang, X., Xiang, W., Miao, X., Li, F., Qi, G., Cao, C., Ma, X., Chen, S., Zimmerman, A. R., & Gao, B. (2022) · The Science of The Total Environment · doi:10.1016/j.scitotenv.2022.153996 · Cited by 89
Self-citationKim, H.-B., Kim, J.-G., Kim, T., Alessi, D. S., & Baek, K. (2020) · Chemical Engineering Journal · doi:10.1016/j.cej.2020.124687 · Cited by 85 · cited 1×
“Kim et al. (2020) prepared sawdust biochar and found the absorption band of aromatic rings and aromatic C–”
Metal catalysts supported on biochars: Part I synthesis and characterization
Santos, J. L., Mäki-Arvela, P., Monzón, A., Murzin, D. Y., & Centeno, M. Á. (2020) · Applied Catalysis B: Environment and Energy · doi:10.1016/j.apcatb.2019.118423 · Cited by 79
Xiang, W., Zhang, X., Cao, C., Quan, G., Wang, M., Zimmerman, A. R., & Gao, B. (2022) · Bioresource Technology · doi:10.1016/j.biortech.2022.127274 · Cited by 78 · cited 2×
“…microporosity and alkalinity of biochar, such as CO 2 activation (Dissanayake et al. 2020), ultrasonic treatment (Shafawi et al. 2021), impregnation (Zhang et al. 2022b), grafting (Zhang et al. 2022a), solid–solid mixing (Rashidi and Yusup 2016), ligand functionalization (Mankar et al. 2021), etc.”
Self-citationLi, H., Li, J., Fan, X., Li, X., & Gao, X. (2019) · Fuel · doi:10.1016/j.fuel.2018.10.139 · Cited by 76 · cited 1×
“Li et al. (2019) prepared sawdust and oil sludge biochar, and found that biochar with higher carbon content exhibited higher heating rate and pyrolysis efficiency under microwave irradiation.”
Dai, Q., Liu, Q., Zhang, X., Cao, L., Hu, B., Shao, J., Ding, F., Guo, X., & Gao, B. (2022) · Fuel · doi:10.1016/j.fuel.2022.124587 · Cited by 71
Self-citationZhang, J., Huang, D., Shao, J., Zhang, X., Zhang, S., Yang, H., & Chen, H. (2022) · Fuel Processing Technology · doi:10.1016/j.fuproc.2022.107250 · Cited by 64
Self-citationAdsorption of CO2 using biochar - Review of the impact of gas mixtures and water on adsorption
Mamaghani, Z. G., Hawboldt, K., & MacQuarrie, S. (2023) · Journal of environmental chemical engineering · doi:10.1016/j.jece.2023.109643 · Cited by 63 · cited 2×
“The typical flue gas from coal-fired power plants usually contains 10–16% CO 2 and small traces of NOx and SOx (Ghanbarpour Mamaghani et al. 2023), so the volume concentrations of CO 2 , NO, and SO 2 used in multicompetent competitive adsorption experiment were 12 vol%, 0.4 vol%, and 0.4 vol%,…”
InfluentialJellali, S., El-Bassi, L., Charabi, Y., Usman, M., Khiari, B., Al-Wardy, M., & Jeguirim, M. (2021) · Journal of Environmental Management · doi:10.1016/j.jenvman.2021.114368 · Cited by 60 · cited 1×
“As a newly emerged carbon material, biochar has been widely used in environmental management and ecological restoration, which is also a promising candidate for CO 2 capture (Jellali et al. 2022; Zhang et al. 2022b).”
Microwave synthesis of biochar for environmental applications
Shirvanimoghaddam, K., Czech, B., Abdikheibari, S., Brodie, G. I., Kończak, M., Krzyszczak, A., Al–Othman, A., & Naebe, M. (2021) · Journal of Analytical and Applied Pyrolysis · doi:10.1016/j.jaap.2021.105415 · Cited by 46
Enhanced 2-D MOFs nanosheets/PIM-PMDA-OH mixed matrix membrane for efficient CO2 separation
Ma, Y., He, X., Tang, S., et al. (2022) · Journal of environmental chemical engineering · doi:10.1016/j.jece.2022.107274 · Cited by 44
Baghery, R., Riahi, S., Abbasi, M., & Mohammadi‐Khanaposhtani, M. (2019) · Journal of Molecular Liquids · doi:10.1016/j.molliq.2019.111431 · Cited by 38
Guo, T., Tian, W., & Wang, Y. (2022) · Atmosphere · doi:10.3390/atmos13071110 · Cited by 32 · cited 1×
“Adsorption capacity of biochar is affected by many factors, such as porosity (Guo et al. 2022), alkalinity (Kumar et al. 2015), surface functional groups (Torrisi et al. 2010), mineral content (Li et al. 2017), hydro-philicity and hydrophobicity (Dissanayake et al. 2020).”
Mankar, J. S., Rayalu, S. S., Balasubramanian, R., & Krupadam, R. J. (2021) · Chemosphere · doi:10.1016/j.chemosphere.2021.131405 · Cited by 27 · cited 1×
“…microporosity and alkalinity of biochar, such as CO 2 activation (Dissanayake et al. 2020), ultrasonic treatment (Shafawi et al. 2021), impregnation (Zhang et al. 2022b), grafting (Zhang et al. 2022a), solid–solid mixing (Rashidi and Yusup 2016), ligand functionalization (Mankar et al. 2021), etc.”
Enhanced 2-D MOFs nanosheets/PES-g-PEG mixed matrix membrane for efficient CO2 separation
Ma, Y., He, X., Xu, S., Yu, Y., Zhang, C., Meng, J., Zeng, L., & Tang, K. (2022) · Chemical Engineering Research and Design · doi:10.1016/j.cherd.2022.02.017
Cited by
Shi, W., Guo, Y., Lu, Q., Li, H., Liang, Y., Ma, F., Yang, B., & Chang, B. (2025) · Green Chemistry · doi:10.1039/d5gc03217b · Cited by 52
Ma, J., Zheng, L., & Yu, F. (2024) · Desalination · doi:10.1016/j.desal.2024.117597 · Cited by 35
Iron-modified coal gangue/rice husk biochar composites for enhanced removal of aqueous As(V)
Kong, W., Li, X., Li, F., Zimmerman, A. R., Gao, B., & Wang, J. (2024) · Separation and Purification Technology · doi:10.1016/j.seppur.2024.131028 · Cited by 29
Self-citationLi, M., Liu, W., Mao, Y., Liu, K., Zhang, L., Cao, Z., Ma, Q., Ye, L., & Peng, H. (2024) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2024.08.028 · Cited by 26
Liu, K., Liu, K., Ye, L., et al. (2025) · Fuel · doi:10.1016/j.fuel.2025.134588 · Cited by 22
Metadata
- Authors
- Zhang, X., Xu, H., Xiang, W., You, X., Dai, H., & Gao, B.
- Affiliations
- Xuzhou University of Technology (CN)
- Rensselaer Polytechnic Institute (US)
- Corresponding author
- Zhang, Xueyang
- ORCID
- Zhang, Xueyang
- Venue
- Biochar
- Published
- 2024-03-08
- Volume
- 6
- Issue
- 1
- ISSN
- 2524-7867 (ISSN-L)
- OpenAlex
- W4392593234
- Cited by
- 40
- References
- 62
- Citations by year
- 2026: 16 · 2025: 19 · 2024: 7
- FWCI
- 5.19
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- cc-by
- creativecommons.org/licenses/by/4.0 (tdm)
- creativecommons.org/licenses/by/4.0 (vor)
- Locations
- Biochar (publishedVersion, cc-by)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Funders
- Basic Research Program of Jiangsu Province (BK20201151)
- Natural Science Foundation of Xuzhou City (KC21288)
- Topics
- Physical Sciences › Chemical Engineering › Filtration and Separation › Carbon Dioxide Capture Technologies
- Physical Sciences › Materials Science › Materials Chemistry › Catalytic Processes in Materials Science
- Physical Sciences › Chemical Engineering › Catalysis › Catalysts for Methane Reforming
- Keywords
- bamboo biochar, CO2 capture, microwave irradiation, CO2 adsorption, pore structure, micropores, impregnation ratio, Avrami equation
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-11, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-11 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.